Geneve's Virtual Network Identifier (VNI) is 24 bit long, so the range
of values for it would be from 0 to 16777215 (2^24 -1).  However, one
cannot create a geneve device with VNI set to 16777215. This patch fixes
this issue.
Signed-off-by: NGirish Moodalbail <girish.moodalbail@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With SYSTEMPORT Lite we have holes in our statistics layout that make us
skip over the hardware MIB counters, bcm_sysport_get_stats() was not
taking that into account resulting in reporting 0 for all SW-maintained
statistics, fix this by skipping accordingly.

Fixes: 44a4524c ("net: systemport: Add support for SYSTEMPORT Lite")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a link between two nodes come up, both endpoints will initially
send out a STATE message to the peer, to increase the probability that
the peer endpoint also is up when the first traffic message arrives.
Thereafter, if the establishing link is the second link between two
nodes, this first "traffic" message is a TUNNEL_PROTOCOL/SYNCH message,
helping the peer to perform initial synchronization between the two
links.

However, the initial STATE message may be lost, in which case the SYNCH
message will be the first one arriving at the peer. This should also
work, as the SYNCH message itself will be used to take up the link
endpoint before  initializing synchronization.

Unfortunately the code for this case is broken. Currently, the link is
brought up through a tipc_link_fsm_evt(ESTABLISHED) when a SYNCH
arrives, whereupon __tipc_node_link_up() is called to distribute the
link slots and take the link into traffic. But, __tipc_node_link_up() is
itself starting with a test for whether the link is up, and if true,
returns without action. Clearly, the tipc_link_fsm_evt(ESTABLISHED) call
is unnecessary, since tipc_node_link_up() is itself issuing such an
event, but also harmful, since it inhibits tipc_node_link_up() to
perform the test of its tasks, and the link endpoint in question hence
is never taken into traffic.

This problem has been exposed when we set up dual links between pre-
and post-4.4 kernels, because the former ones don't send out the
initial STATE message described above.

We fix this by removing the unnecessary event call.
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 65d8fc77 ("futex: Remove requirement for lock_page() in
get_futex_key()") removed an unnecessary lock_page() with the
side-effect that page->mapping needed to be treated very carefully.

Two defensive warnings were added in case any assumption was missed and
the first warning assumed a correct application would not alter a
mapping backing a futex key.  Since merging, it has not triggered for
any unexpected case but Mark Rutland reported the following bug
triggering due to the first warning.

  kernel BUG at kernel/futex.c:679!
  Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
  Modules linked in:
  CPU: 0 PID: 3695 Comm: syz-executor1 Not tainted 4.13.0-rc3-00020-g307fec773ba3 #3
  Hardware name: linux,dummy-virt (DT)
  task: ffff80001e271780 task.stack: ffff000010908000
  PC is at get_futex_key+0x6a4/0xcf0 kernel/futex.c:679
  LR is at get_futex_key+0x6a4/0xcf0 kernel/futex.c:679
  pc : [<ffff00000821ac14>] lr : [<ffff00000821ac14>] pstate: 80000145

The fact that it's a bug instead of a warning was due to an unrelated
arm64 problem, but the warning itself triggered because the underlying
mapping changed.

This is an application issue but from a kernel perspective it's a
recoverable situation and the warning is unnecessary so this patch
removes the warning.  The warning may potentially be triggered with the
following test program from Mark although it may be necessary to adjust
NR_FUTEX_THREADS to be a value smaller than the number of CPUs in the
system.

    #include <linux/futex.h>
    #include <pthread.h>
    #include <stdio.h>
    #include <stdlib.h>
    #include <sys/mman.h>
    #include <sys/syscall.h>
    #include <sys/time.h>
    #include <unistd.h>

    #define NR_FUTEX_THREADS 16
    pthread_t threads[NR_FUTEX_THREADS];

    void *mem;

    #define MEM_PROT  (PROT_READ | PROT_WRITE)
    #define MEM_SIZE  65536

    static int futex_wrapper(int *uaddr, int op, int val,
                             const struct timespec *timeout,
                             int *uaddr2, int val3)
    {
        syscall(SYS_futex, uaddr, op, val, timeout, uaddr2, val3);
    }

    void *poll_futex(void *unused)
    {
        for (;;) {
            futex_wrapper(mem, FUTEX_CMP_REQUEUE_PI, 1, NULL, mem + 4, 1);
        }
    }

    int main(int argc, char *argv[])
    {
        int i;

        mem = mmap(NULL, MEM_SIZE, MEM_PROT,
               MAP_SHARED | MAP_ANONYMOUS, -1, 0);

        printf("Mapping @ %p\n", mem);

        printf("Creating futex threads...\n");

        for (i = 0; i < NR_FUTEX_THREADS; i++)
            pthread_create(&threads[i], NULL, poll_futex, NULL);

        printf("Flipping mapping...\n");
        for (;;) {
            mmap(mem, MEM_SIZE, MEM_PROT,
                 MAP_FIXED | MAP_SHARED | MAP_ANONYMOUS, -1, 0);
        }

        return 0;
    }
Reported-and-tested-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NMel Gorman <mgorman@suse.de>
Acked-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Cc: stable@vger.kernel.org # 4.7+
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull i2c fixes from Wolfram Sang:
 "The main thing is to allow empty id_tables for ACPI to make some
  drivers get probed again. It looks a bit bigger than usual because it
  needs some internal renaming, too.

  Other than that, there is a fix for broken DSTDs, a super simple
  enablement for ARM MPS, and two documentation fixes which I'd like to
  see in v4.13 already"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: rephrase explanation of I2C_CLASS_DEPRECATED
  i2c: allow i2c-versatile for ARM MPS platforms
  i2c: designware: Some broken DSTDs use 1MiHz instead of 1MHz
  i2c: designware: Print clock freq on invalid clock freq error
  i2c: core: Allow empty id_table in ACPI case as well
  i2c: mux: pinctrl: mention correct module name in Kconfig help text

Pull block fixes from Jens Axboe:
 "Three patches that should go into this release.

  Two of them are from Paolo and fix up some corner cases with BFQ, and
  the last patch is from Ming and fixes up a potential usage count
  imbalance regression due to the recent NOWAIT work"

* 'for-linus' of git://git.kernel.dk/linux-block:
  blk-mq: don't leak preempt counter/q_usage_counter when allocating rq failed
  block, bfq: consider also in_service_entity to state whether an entity is active
  block, bfq: reset in_service_entity if it becomes idle

Pull crypto fixes from Herbert Xu:
 "Fix two regressions in the inside-secure driver with respect to
  hmac(sha1)"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: inside-secure - fix the sha state length in hmac_sha1_setkey
  crypto: inside-secure - fix invalidation check in hmac_sha1_setkey

Pull networking fixes from David Miller:
 "The pull requests are getting smaller, that's progress I suppose :-)

   1) Fix infinite loop in CIPSO option parsing, from Yujuan Qi.

   2) Fix remote checksum handling in VXLAN and GUE tunneling drivers,
      from Koichiro Den.

   3) Missing u64_stats_init() calls in several drivers, from Florian
      Fainelli.

   4) TCP can set the congestion window to an invalid ssthresh value
      after congestion window reductions, from Yuchung Cheng.

   5) Fix BPF jit branch generation on s390, from Daniel Borkmann.

   6) Correct MIPS ebpf JIT merge, from David Daney.

   7) Correct byte order test in BPF test_verifier.c, from Daniel
      Borkmann.

   8) Fix various crashes and leaks in ASIX driver, from Dean Jenkins.

   9) Handle SCTP checksums properly in mlx4 driver, from Davide
      Caratti.

  10) We can potentially enter tcp_connect() with a cached route
      already, due to fastopen, so we have to explicitly invalidate it.

  11) skb_warn_bad_offload() can bark in legitimate situations, fix from
      Willem de Bruijn"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
  net: avoid skb_warn_bad_offload false positives on UFO
  qmi_wwan: fix NULL deref on disconnect
  ppp: fix xmit recursion detection on ppp channels
  rds: Reintroduce statistics counting
  tcp: fastopen: tcp_connect() must refresh the route
  net: sched: set xt_tgchk_param par.net properly in ipt_init_target
  net: dsa: mediatek: add adjust link support for user ports
  net/mlx4_en: don't set CHECKSUM_COMPLETE on SCTP packets
  qed: Fix a memory allocation failure test in 'qed_mcp_cmd_init()'
  hysdn: fix to a race condition in put_log_buffer
  s390/qeth: fix L3 next-hop in xmit qeth hdr
  asix: Fix small memory leak in ax88772_unbind()
  asix: Ensure asix_rx_fixup_info members are all reset
  asix: Add rx->ax_skb = NULL after usbnet_skb_return()
  bpf: fix selftest/bpf/test_pkt_md_access on s390x
  netvsc: fix race on sub channel creation
  bpf: fix byte order test in test_verifier
  xgene: Always get clk source, but ignore if it's missing for SGMII ports
  MIPS: Add missing file for eBPF JIT.
  bpf, s390: fix build for libbpf and selftest suite
  ...

skb_warn_bad_offload triggers a warning when an skb enters the GSO
stack at __skb_gso_segment that does not have CHECKSUM_PARTIAL
checksum offload set.

Commit b2504a5d ("net: reduce skb_warn_bad_offload() noise")
observed that SKB_GSO_DODGY producers can trigger the check and
that passing those packets through the GSO handlers will fix it
up. But, the software UFO handler will set ip_summed to
CHECKSUM_NONE.

When __skb_gso_segment is called from the receive path, this
triggers the warning again.

Make UFO set CHECKSUM_UNNECESSARY instead of CHECKSUM_NONE. On
Tx these two are equivalent. On Rx, this better matches the
skb state (checksum computed), as CHECKSUM_NONE here means no
checksum computed.

See also this thread for context:
http://patchwork.ozlabs.org/patch/799015/

Fixes: b2504a5d ("net: reduce skb_warn_bad_offload() noise")
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

qmi_wwan_disconnect is called twice when disconnecting devices with
separate control and data interfaces.  The first invocation will set
the interface data to NULL for both interfaces to flag that the
disconnect has been handled.  But the matching NULL check was left
out when qmi_wwan_disconnect was added, resulting in this oops:

  usb 2-1.4: USB disconnect, device number 4
  qmi_wwan 2-1.4:1.6 wwp0s29u1u4i6: unregister 'qmi_wwan' usb-0000:00:1d.0-1.4, WWAN/QMI device
  BUG: unable to handle kernel NULL pointer dereference at 00000000000000e0
  IP: qmi_wwan_disconnect+0x25/0xc0 [qmi_wwan]
  PGD 0
  P4D 0
  Oops: 0000 [#1] SMP
  Modules linked in: <stripped irrelevant module list>
  CPU: 2 PID: 33 Comm: kworker/2:1 Tainted: G            E   4.12.3-nr44-normandy-r1500619820+ #1
  Hardware name: LENOVO 4291LR7/4291LR7, BIOS CBET4000 4.6-810-g50522254fb 07/21/2017
  Workqueue: usb_hub_wq hub_event [usbcore]
  task: ffff8c882b716040 task.stack: ffffb8e800d84000
  RIP: 0010:qmi_wwan_disconnect+0x25/0xc0 [qmi_wwan]
  RSP: 0018:ffffb8e800d87b38 EFLAGS: 00010246
  RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
  RDX: 0000000000000001 RSI: ffff8c8824f3f1d0 RDI: ffff8c8824ef6400
  RBP: ffff8c8824ef6400 R08: 0000000000000000 R09: 0000000000000000
  R10: ffffb8e800d87780 R11: 0000000000000011 R12: ffffffffc07ea0e8
  R13: ffff8c8824e2e000 R14: ffff8c8824e2e098 R15: 0000000000000000
  FS:  0000000000000000(0000) GS:ffff8c8835300000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 00000000000000e0 CR3: 0000000229ca5000 CR4: 00000000000406e0
  Call Trace:
   ? usb_unbind_interface+0x71/0x270 [usbcore]
   ? device_release_driver_internal+0x154/0x210
   ? qmi_wwan_unbind+0x6d/0xc0 [qmi_wwan]
   ? usbnet_disconnect+0x6c/0xf0 [usbnet]
   ? qmi_wwan_disconnect+0x87/0xc0 [qmi_wwan]
   ? usb_unbind_interface+0x71/0x270 [usbcore]
   ? device_release_driver_internal+0x154/0x210
Reported-and-tested-by: NNathaniel Roach <nroach44@gmail.com>
Fixes: c6adf779 ("net: usb: qmi_wwan: add qmap mux protocol support")
Cc: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit e5dadc65 ("ppp: Fix false xmit recursion detect with two ppp
devices") dropped the xmit_recursion counter incrementation in
ppp_channel_push() and relied on ppp_xmit_process() for this task.
But __ppp_channel_push() can also send packets directly (using the
.start_xmit() channel callback), in which case the xmit_recursion
counter isn't incremented anymore. If such packets get routed back to
the parent ppp unit, ppp_xmit_process() won't notice the recursion and
will call ppp_channel_push() on the same channel, effectively creating
the deadlock situation that the xmit_recursion mechanism was supposed
to prevent.

This patch re-introduces the xmit_recursion counter incrementation in
ppp_channel_push(). Since the xmit_recursion variable is now part of
the parent ppp unit, incrementation is skipped if the channel doesn't
have any. This is fine because only packets routed through the parent
unit may enter the channel recursively.

Finally, we have to ensure that pch->ppp is not going to be modified
while executing ppp_channel_push(). Instead of taking this lock only
while calling ppp_xmit_process(), we now have to hold it for the full
ppp_channel_push() execution. This respects the ppp locks ordering
which requires locking ->upl before ->downl.

Fixes: e5dadc65 ("ppp: Fix false xmit recursion detect with two ppp devices")
Signed-off-by: NGuillaume Nault <g.nault@alphalink.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 7e3f2952 ("rds: don't let RDS shutdown a connection
while senders are present"), refilling the receive queue was removed
from rds_ib_recv(), along with the increment of
s_ib_rx_refill_from_thread.

Commit 73ce4317 ("RDS: make sure we post recv buffers")
re-introduces filling the receive queue from rds_ib_recv(), but does
not add the statistics counter. rds_ib_recv() was later renamed to
rds_ib_recv_path().

This commit reintroduces the statistics counting of
s_ib_rx_refill_from_thread and s_ib_rx_refill_from_cq.
Signed-off-by: NHåkon Bugge <haakon.bugge@oracle.com>
Reviewed-by: NKnut Omang <knut.omang@oracle.com>
Reviewed-by: NWei Lin Guay <wei.lin.guay@oracle.com>
Reviewed-by: NShamir Rabinovitch <shamir.rabinovitch@oracle.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With new TCP_FASTOPEN_CONNECT socket option, there is a possibility
to call tcp_connect() while socket sk_dst_cache is either NULL
or invalid.

 +0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 4
 +0 fcntl(4, F_SETFL, O_RDWR|O_NONBLOCK) = 0
 +0 setsockopt(4, SOL_TCP, TCP_FASTOPEN_CONNECT, [1], 4) = 0
 +0 connect(4, ..., ...) = 0

<< sk->sk_dst_cache becomes obsolete, or even set to NULL >>

 +1 sendto(4, ..., 1000, MSG_FASTOPEN, ..., ...) = 1000

We need to refresh the route otherwise bad things can happen,
especially when syzkaller is running on the host :/

Fixes: 19f6d3f3 ("net/tcp-fastopen: Add new API support")
Reported-by: NDmitry Vyukov <dvyukov@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: NWei Wang <weiwan@google.com>
Acked-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now xt_tgchk_param par in ipt_init_target is a local varibale,
par.net is not initialized there. Later when xt_check_target
calls target's checkentry in which it may access par.net, it
would cause kernel panic.

Jaroslav found this panic when running:

  # ip link add TestIface type dummy
  # tc qd add dev TestIface ingress handle ffff:
  # tc filter add dev TestIface parent ffff: u32 match u32 0 0 \
    action xt -j CONNMARK --set-mark 4

This patch is to pass net param into ipt_init_target and set
par.net with it properly in there.

v1->v2:
  As Wang Cong pointed, I missed ipt_net_id != xt_net_id, so fix
  it by also passing net_id to __tcf_ipt_init.
v2->v3:
  Missed the fixes tag, so add it.

Fixes: ecb2421b ("netfilter: add and use nf_ct_netns_get/put")
Reported-by: NJaroslav Aster <jaster@redhat.com>
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Manually adjust the port settings of user ports once PHY polling has
completed. This patch extends the adjust_link callback to configure the
per port PMCR register, applying the proper values polled from the PHY.
Without this patch flow control was not always getting setup properly.
Signed-off-by: NShashidhar Lakkavalli <shashidhar.lakkavalli@openmesh.com>
Signed-off-by: NMuciri Gatimu <muciri@openmesh.com>
Signed-off-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

if the NIC fails to validate the checksum on TCP/UDP, and validation of IP
checksum is successful, the driver subtracts the pseudo-header checksum
from the value obtained by the hardware and sets CHECKSUM_COMPLETE. Don't
do that if protocol is IPPROTO_SCTP, otherwise CRC32c validation fails.

V2: don't test MLX4_CQE_STATUS_IPV6 if MLX4_CQE_STATUS_IPV4 is set
Reported-by: NShuang Li <shuali@redhat.com>
Fixes: f8c6455b ("net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE")
Signed-off-by: NDavide Caratti <dcaratti@redhat.com>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull rdma fixes from Doug Ledford:
 "Third set of -rc fixes for 4.13 cycle

   - small set of miscellanous fixes

   - a reasonably sizable set of IPoIB fixes that deal with multiple
     long standing issues"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
  IB/hns: checking for IS_ERR() instead of NULL
  RDMA/mlx5: Fix existence check for extended address vector
  IB/uverbs: Fix device cleanup
  RDMA/uverbs: Prevent leak of reserved field
  IB/core: Fix race condition in resolving IP to MAC
  IB/ipoib: Notify on modify QP failure only when relevant
  Revert "IB/core: Allow QP state transition from reset to error"
  IB/ipoib: Remove double pointer assigning
  IB/ipoib: Clean error paths in add port
  IB/ipoib: Add get statistics support to SRIOV VF
  IB/ipoib: Add multicast packets statistics
  IB/ipoib: Set IPOIB_NEIGH_TBL_FLUSH after flushed completion initialization
  IB/ipoib: Prevent setting negative values to max_nonsrq_conn_qp
  IB/ipoib: Make sure no in-flight joins while leaving that mcast
  IB/ipoib: Use cancel_delayed_work_sync when needed
  IB/ipoib: Fix race between light events and interface restart

Allow any number of command line arguments to match either the
section header or the section contents and create new files.

Create MAINTAINERS.new and SECTION.new.

This allows scripting of the movement of various sections from
MAINTAINERS.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Instead of reading STDIN and writing STDOUT, use specific filenames of
MAINTAINERS and MAINTAINERS.new.

Use hash references instead of global hash %hash so future modifications
can read and write specific hashes to split up MAINTAINERS into multiple
files using a script.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Section [A-Z]: patterns are not currently in any required sorting order.
Add a specific sorting sequence to MAINTAINERS entries.
Sort F: and X: patterns in alphabetic order.

The preferred section ordering is:

  SECTION HEADER
  M:	Maintainers
  R:	Reviewers
  P:	Named persons without email addresses
  L:	Mailing list addresses
  S:	Status of this section (Supported, Maintained, Orphan, etc...)
  W:	Any relevant URLs
  T:	Source code control type (git, quilt, etc)
  Q:	Patchwork patch acceptance queue site
  B:	Bug tracking URIs
  C:	Chat URIs
  F:	Files with wildcard patterns (alphabetic ordered)
  X:	Excluded files with wildcard patterns (alphabetic ordered)
  N:	Files with regex patterns
  K:	Keyword regexes in source code for maintainership identification

Miscellaneous perl neatening:

 - Rename %map to %hash, map has a different meaning in perl
 - Avoid using \& and local variables for function indirection
 - Use return for a little c like clarity
 - Use c-like function call style instead of &function
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Allow for MAINTAINERS to become a directory and if it is,
read all the files in the directory for maintained sections.

Optionally look for all files named MAINTAINERS in directories
excluding the .git directory by using --find-maintainer-files.

This optional feature adds ~.3 seconds of CPU on an Intel
i5-6200 with an SSD.

Miscellanea:

 - Create a read_maintainer_file subroutine from the existing code
 - Test only the existence of MAINTAINERS, not whether it's a file
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The openbmc mailing list is moderated for non-subscribers.
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Acked-by: NBrendan Higgins <brendanhiggins@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Joel Stanley <joel@jms.id.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fixes: f47e07bc ("Fix up MAINTAINERS file problems")
Cc: Joe Perches <joe@perches.com>
Signed-off-by: NSedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull SCSI fixes from James Bottomley:
 "Two small fixes, one re-fix of a previous fix and five patches sorting
  out hotplug in the bnx2X class of drivers. The latter is rather
  involved, but necessary because these drivers have started dropping
  lockdep recursion warnings on the hotplug lock because of its
  conversion to a percpu rwsem"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: sg: only check for dxfer_len greater than 256M
  scsi: aacraid: reading out of bounds
  scsi: qedf: Limit number of CQs
  scsi: bnx2i: Simplify cpu hotplug code
  scsi: bnx2fc: Simplify CPU hotplug code
  scsi: bnx2i: Prevent recursive cpuhotplug locking
  scsi: bnx2fc: Prevent recursive cpuhotplug locking
  scsi: bnx2fc: Plug CPU hotplug race

Fix the warning message on the parisc and IA64 architectures to show the
correct function name of the caller by using %pS instead of %pF. The
message is printed with the value of _RET_IP_ which calls
__builtin_return_address(0) and as such returns the IP address caller
instead of pointer to a function descriptor of the caller.

The effect of this patch is visible on the parisc and ia64 architectures
only since those are the ones which use function descriptors while on
all others %pS and %pF will behave the same.

Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: NHelge Deller <deller@gmx.de>
Fixes: eecabf56 ("random: suppress spammy warnings about unseeded randomness")
Fixes: d06bfd19 ("random: warn when kernel uses unseeded randomness")
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull Xtensa fixes from Max Filippov:

 - use asm-generic instances of asm/param.h and asm/device.h instead of
   exact copies in arch/xtensa/include/asm;

 - fix build error for xtensa cores with aliasing WT cache: define cache
   flushing functions and copy_{to,from}_user_page;

 - add missing EXPORT_SYMBOLs for clear_user_highpage, copy_user_highpage,
   flush_dcache_page, local_flush_cache_range, local_flush_cache_page,
   csum_partial and csum_partial_copy_generic.

* tag 'xtensa-20170807' of git://github.com/jcmvbkbc/linux-xtensa:
  xtensa: mm/cache: add missing EXPORT_SYMBOLs
  xtensa: don't limit csum_partial export by CONFIG_NET
  xtensa: fix cache aliasing handling code for WT cache
  xtensa: remove wrapper header for asm/param.h
  xtensa: remove wrapper header for asm/device.h

Pull MTD fixes from Brian Norris:
 "I missed getting these out for rc4, but here are some MTD fixes.

  Just NAND fixes (in both the core handling, and a few drivers). Notes
  stolen from Boris:

  Core fixes:

   - fix data interface setup for ONFI NANDs that do not support the SET
     FEATURES command

   - fix a kernel doc header

   - fix potential integer overflow when retrieving timing information
     from the parameter page

   - fix wrong OOB layout for small page NANDs

  Driver fixes:

   - fix potential division-by-zero bug

   - fix backward compat with old atmel-nand DT bindings

   - fix ->setup_data_interface() in the atmel NAND driver"

* tag 'for-linus-20170807' of git://git.infradead.org/linux-mtd:
  mtd: nand: atmel: Fix EDO mode check
  mtd: nand: Declare tBERS, tR and tPROG as u64 to avoid integer overflow
  mtd: nand: Fix timing setup for NANDs that do not support SET FEATURES
  mtd: nand: Fix a docs build warning
  mtd: nand: sunxi: fix potential divide-by-zero error
  nand: fix wrong default oob layout for small pages using soft ecc
  mtd: nand: atmel: Fix DT backward compatibility in pmecc.c

Pull xfs fixes from Darrick Wong:
 "I have a couple more bug fixes for you today:

   - fix memory leak when issuing discard

   - fix propagation of the dax inode flag"

* tag 'xfs-4.13-fixes-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: Fix per-inode DAX flag inheritance
  xfs: Fix leak of discard bio

We allocate 'p_info->mfw_mb_cur' and 'p_info->mfw_mb_shadow' but we check
'p_info->mfw_mb_addr' instead of 'p_info->mfw_mb_cur'.

'p_info->mfw_mb_addr' is never 0, because it is initiliazed a few lines
above in 'qed_load_mcp_offsets()'.

Update the test and check the result of the 2 'kzalloc()' instead.
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: NTomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The synchronization type that was used earlier to guard the loop that
deletes unused log buffers may lead to a situation that prevents any
thread from going through the loop.

The patch deletes previously used synchronization mechanism and moves
the loop under the spin_lock so the similar cases won't be feasible in
the future.

Found by by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAnton Volkov <avolkov@ispras.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On L3, the qeth_hdr struct needs to be filled with the next-hop
IP address.
The current code accesses rtable->rt_gateway without checking that
rtable is a valid address. The accidental access to a lowcore area
results in a random next-hop address in the qeth_hdr.
rtable (or more precisely, skb_dst(skb)) can be NULL in rare cases
(for instance together with AF_PACKET sockets).
This patch adds the missing NULL-ptr checks.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Fixes: 87e7597b qeth: Move away from using neighbour entries in qeth_l3_fill_header()
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'rdma-rc-2017-07-26' of git://git.kernel.org/pub/scm/linux/kernel/git/leon/linux-rdma into leon-ipoib

IPoIB fixes for 4.13

The patchset provides various fixes for IPoIB. It is combination of
fixes to various issues discovered during verification along with
static checkers cleanup patches.

Most of the patches are from pre-git era and hence lack of Fixes lines.

There is one exception in this IPoIB group - addition of patch revert:
Revert "IB/core: Allow QP state transition from reset to error", but
it followed by proper fix to the annoying print, so I thought it is
appropriate to include it.
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Dean Jenkins says:

====================
asix: Improve robustness

Please consider taking these patches to improve the robustness of the ASIX USB
to Ethernet driver.

Failures prompting an ASIX driver code review
=============================================

On an ARM i.MX6 embedded platform some strange one-off and two-off failures were
observed in and around the ASIX USB to Ethernet driver. This was observed on a
highly modified kernel 3.14 with the ASIX driver containing back-ported changes
from kernel.org up to kernel 4.8 approximately.

a) A one-off failure in asix_rx_fixup_internal():

There was an occurrence of an attempt to write off the end of the netdev buffer
which was trapped by skb_over_panic() in skb_put().

[20030.846440] skbuff: skb_over_panic: text:7f2271c0 len:120 put:60 head:8366ecc0 data:8366ed02 tail:0x8366ed7a end:0x8366ed40 dev:eth0
[20030.863007] Kernel BUG at 8044ce38 [verbose debug info unavailable]

[20031.215345] Backtrace:
[20031.217884] [<8044cde0>] (skb_panic) from [<8044d50c>] (skb_put+0x50/0x5c)
[20031.227408] [<8044d4bc>] (skb_put) from [<7f2271c0>] (asix_rx_fixup_internal+0x1c4/0x23c [asix])
[20031.242024] [<7f226ffc>] (asix_rx_fixup_internal [asix]) from [<7f22724c>] (asix_rx_fixup_common+0x14/0x18 [asix])
[20031.260309] [<7f227238>] (asix_rx_fixup_common [asix]) from [<7f21f7d4>] (usbnet_bh+0x74/0x224 [usbnet])
[20031.269879] [<7f21f760>] (usbnet_bh [usbnet]) from [<8002f834>] (call_timer_fn+0xa4/0x1f0)
[20031.283961] [<8002f790>] (call_timer_fn) from [<80030834>] (run_timer_softirq+0x230/0x2a8)
[20031.302782] [<80030604>] (run_timer_softirq) from [<80028780>] (__do_softirq+0x15c/0x37c)
[20031.321511] [<80028624>] (__do_softirq) from [<80028c38>] (irq_exit+0x8c/0xe8)
[20031.339298] [<80028bac>] (irq_exit) from [<8000e9c8>] (handle_IRQ+0x8c/0xc8)
[20031.350038] [<8000e93c>] (handle_IRQ) from [<800085c8>] (gic_handle_irq+0xb8/0xf8)
[20031.365528] [<80008510>] (gic_handle_irq) from [<8050de80>] (__irq_svc+0x40/0x70)

Analysis of the logic of the ASIX driver (containing backported changes from
kernel.org up to kernel 4.8 approximately) suggested that the software could not
trigger skb_over_panic(). The analysis of the kernel BUG() crash information
suggested that the netdev buffer was written with 2 minimal 60 octet length
Ethernet frames (ASIX hardware drops the 4 octet FCS field) and the 2nd Ethernet
frame attempted to write off the end of the netdev buffer.

Note that the netdev buffer should only contain 1 Ethernet frame so if an
attempt to write 2 Ethernet frames into the buffer is made then that is wrong.
However, the logic of the asix_rx_fixup_internal() only allows 1 Ethernet frame
to be written into the netdev buffer.

Potentially this failure was due to memory corruption because it was only seen
once.

b) Two-off failures in the NAPI layer's backlog queue:

There were 2 crashes in the NAPI layer's backlog queue presumably after
asix_rx_fixup_internal() called usbnet_skb_return().

[24097.273945] Unable to handle kernel NULL pointer dereference at virtual address 00000004

[24097.398944] PC is at process_backlog+0x80/0x16c

[24097.569466] Backtrace:
[24097.572007] [<8045ad98>] (process_backlog) from [<8045b64c>] (net_rx_action+0xcc/0x248)
[24097.591631] [<8045b580>] (net_rx_action) from [<80028780>] (__do_softirq+0x15c/0x37c)
[24097.610022] [<80028624>] (__do_softirq) from [<800289cc>] (run_ksoftirqd+0x2c/0x84)

and

[ 1059.828452] Unable to handle kernel NULL pointer dereference at virtual address 00000000

[ 1059.953715] PC is at process_backlog+0x84/0x16c

[ 1060.140896] Backtrace:
[ 1060.143434] [<8045ad98>] (process_backlog) from [<8045b64c>] (net_rx_action+0xcc/0x248)
[ 1060.163075] [<8045b580>] (net_rx_action) from [<80028780>] (__do_softirq+0x15c/0x37c)
[ 1060.181474] [<80028624>] (__do_softirq) from [<80028c38>] (irq_exit+0x8c/0xe8)
[ 1060.199256] [<80028bac>] (irq_exit) from [<8000e9c8>] (handle_IRQ+0x8c/0xc8)
[ 1060.210006] [<8000e93c>] (handle_IRQ) from [<800085c8>] (gic_handle_irq+0xb8/0xf8)
[ 1060.225492] [<80008510>] (gic_handle_irq) from [<8050de80>] (__irq_svc+0x40/0x70)

The embedded board was only using an ASIX USB to Ethernet adaptor eth0.

Analysis suggested that the doubly-linked list pointers of the backlog queue had
been corrupted because one of the link pointers was NULL.

Potentially this failure was due to memory corruption because it was only seen
twice.

Results of the ASIX driver code review
======================================

During the code review some weaknesses were observed in the ASIX driver and the
following patches have been created to improve the robustness.

Brief overview of the patches
-----------------------------

1. asix: Add rx->ax_skb = NULL after usbnet_skb_return()

The current ASIX driver sends the received Ethernet frame to the NAPI layer of
the network stack via the call to usbnet_skb_return() in
asix_rx_fixup_internal() but retains the rx->ax_skb pointer to the netdev
buffer. The driver no longer needs the rx->ax_skb pointer at this point because
the NAPI layer now has the Ethernet frame.

This means that asix_rx_fixup_internal() must not use rx->ax_skb after the call
to usbnet_skb_return() because it could corrupt the handling of the Ethernet
frame within the network layer.

Therefore, to remove the risk of erroneous usage of rx->ax_skb, set rx->ax_skb
to NULL after the call to usbnet_skb_return(). This avoids potential erroneous
freeing of rx->ax_skb and erroneous writing to the netdev buffer.  If the
software now somehow inappropriately reused rx->ax_skb, then a NULL pointer
dereference of rx->ax_skb would occur which makes investigation easier.

2. asix: Ensure asix_rx_fixup_info members are all reset

This patch creates reset_asix_rx_fixup_info() to allow all the
asix_rx_fixup_info structure members to be consistently reset to initial
conditions.

Call reset_asix_rx_fixup_info() upon each detectable error condition so that the
next URB is processed from a known state.

Otherwise, there is a risk that some members of the asix_rx_fixup_info structure
may be incorrect after an error occurred so potentially leading to a
malfunction.

3. asix: Fix small memory leak in ax88772_unbind()

This patch creates asix_rx_fixup_common_free() to allow the rx->ax_skb to be
freed when necessary.

asix_rx_fixup_common_free() is called from ax88772_unbind() before the parent
private data structure is freed.

Without this patch, there is a risk of a small netdev buffer memory leak each
time ax88772_unbind() is called during the reception of an Ethernet frame that
spans across 2 URBs.

Testing
=======

The patches have been sanity tested on a 64-bit Linux laptop running kernel
4.13-rc2 with the 3 patches applied on top.

The ASIX USB to Adaptor used for testing was (output of lsusb):
ID 0b95:772b ASIX Electronics Corp. AX88772B

Test #1
-------

The test ran a flood ping test script which slowly incremented the ICMP Echo
Request's payload from 0 to 5000 octets. This eventually causes IPv4
fragmentation to occur which causes Ethernet frames to be sent very close to
each other so increases the probability that an Ethernet frame will span 2 URBs.
The test showed that all pings were successful. The test took about 15 minutes
to complete.

Test #2
-------

A script was run on the laptop to periodically run ifdown and ifup every second
so that the ASIX USB to Adaptor was up for 1 second and down for 1 second.

From a Linux PC connected to the laptop, the following ping command was used
ping -f -s 5000 <ip address of laptop>

The large ICMP payload causes IPv4 fragmentation resulting in multiple
Ethernet frames per original IP packet.

Kernel debug within the ASIX driver was enabled to see whether any ASIX errors
were generated. The test was run for about 24 hours and no ASIX errors were
seen.

Patches
=======

The 3 patches have been rebased off the net-next repo master branch with HEAD
fbbeefdd net: fec: Allow reception of frames bigger than 1522 bytes
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When Ethernet frames span mulitple URBs, the netdev buffer memory
pointed to by the asix_rx_fixup_info structure remains allocated
during the time gap between the 2 executions of asix_rx_fixup_internal().

This means that if ax88772_unbind() is called within this time
gap to free the memory of the parent private data structure then
a memory leak of the part filled netdev buffer memory will occur.

Therefore, create a new function asix_rx_fixup_common_free() to
free the memory of the netdev buffer and add a call to
asix_rx_fixup_common_free() from inside ax88772_unbind().

Consequently when an unbind occurs part way through receiving
an Ethernet frame, the netdev buffer memory that is holding part
of the received Ethernet frame will now be freed.
Signed-off-by: NDean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a risk that the members of the structure asix_rx_fixup_info
become unsynchronised leading to the possibility of a malfunction.

For example, rx->split_head was not being set to false after an
error was detected so potentially could cause a malformed 32-bit
Data header word to be formed.

Therefore add function reset_asix_rx_fixup_info() to reset all the
members of asix_rx_fixup_info so that future processing will start
with known initial conditions.

Also, if (skb->len != offset) becomes true then call
reset_asix_rx_fixup_info() so that the processing of the next URB
starts with known initial conditions. Without the call, the check
does nothing which potentially could lead to a malfunction
when the next URB is processed.

In addition, for robustness, call reset_asix_rx_fixup_info() before
every error path's "return 0". This ensures that the next URB is
processed from known initial conditions.
Signed-off-by: NDean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In asix_rx_fixup_internal() there is a risk that rx->ax_skb gets
reused after passing the Ethernet frame into the network stack via
usbnet_skb_return().

The risks include:

a) asynchronously freeing rx->ax_skb after passing the netdev buffer
   to the NAPI layer which might corrupt the backlog queue.

b) erroneously reusing rx->ax_skb such as calling skb_put_data() multiple
   times which causes writing off the end of the netdev buffer.

Therefore add a defensive rx->ax_skb = NULL after usbnet_skb_return()
so that it is not possible to free rx->ax_skb or to apply
skb_put_data() too many times.
Signed-off-by: NDean Jenkins <Dean_Jenkins@mentor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 18f3d6be ("selftests/bpf: Add test cases to test narrower ctx field loads")
introduced new eBPF test cases. One of them (test_pkt_md_access.c)
fails on s390x. The BPF verifier error message is:

[root@s8360046 bpf]# ./test_progs
test_pkt_access:PASS:ipv4 349 nsec
test_pkt_access:PASS:ipv6 212 nsec
[....]
libbpf: load bpf program failed: Permission denied
libbpf: -- BEGIN DUMP LOG ---
libbpf:
0: (71) r2 = *(u8 *)(r1 +0)
invalid bpf_context access off=0 size=1

libbpf: -- END LOG --
libbpf: failed to load program 'test1'
libbpf: failed to load object './test_pkt_md_access.o'
Summary: 29 PASSED, 1 FAILED
[root@s8360046 bpf]#

This is caused by a byte endianness issue. S390x is a big endian
architecture.  Pointer access to the lowest byte or halfword of a
four byte value need to add an offset.
On little endian architectures this offset is not needed.

Fix this and use the same approach as the originator used for other files
(for example test_verifier.c) in his original commit.

With this fix the test program test_progs succeeds on s390x:
[root@s8360046 bpf]# ./test_progs
test_pkt_access:PASS:ipv4 236 nsec
test_pkt_access:PASS:ipv6 217 nsec
test_xdp:PASS:ipv4 3624 nsec
test_xdp:PASS:ipv6 1722 nsec
test_l4lb:PASS:ipv4 926 nsec
test_l4lb:PASS:ipv6 1322 nsec
test_tcp_estats:PASS: 0 nsec
test_bpf_obj_id:PASS:get-fd-by-notexist-prog-id 0 nsec
test_bpf_obj_id:PASS:get-fd-by-notexist-map-id 0 nsec
test_bpf_obj_id:PASS:get-prog-info(fd) 0 nsec
test_bpf_obj_id:PASS:get-map-info(fd) 0 nsec
test_bpf_obj_id:PASS:get-prog-info(fd) 0 nsec
test_bpf_obj_id:PASS:get-map-info(fd) 0 nsec
test_bpf_obj_id:PASS:get-prog-fd(next_id) 0 nsec
test_bpf_obj_id:PASS:get-prog-info(next_id->fd) 0 nsec
test_bpf_obj_id:PASS:get-prog-fd(next_id) 0 nsec
test_bpf_obj_id:PASS:get-prog-info(next_id->fd) 0 nsec
test_bpf_obj_id:PASS:check total prog id found by get_next_id 0 nsec
test_bpf_obj_id:PASS:get-map-fd(next_id) 0 nsec
test_bpf_obj_id:PASS:get-map-fd(next_id) 0 nsec
test_bpf_obj_id:PASS:get-map-fd(next_id) 0 nsec
test_bpf_obj_id:PASS:get-map-fd(next_id) 0 nsec
test_bpf_obj_id:PASS:get-map-fd(next_id) 0 nsec
test_bpf_obj_id:PASS:get-map-fd(next_id) 0 nsec
test_bpf_obj_id:PASS:get-map-fd(next_id) 0 nsec
test_bpf_obj_id:PASS:check get-map-info(next_id->fd) 0 nsec
test_bpf_obj_id:PASS:get-map-fd(next_id) 0 nsec
test_bpf_obj_id:PASS:check get-map-info(next_id->fd) 0 nsec
test_bpf_obj_id:PASS:check total map id found by get_next_id 0 nsec
test_pkt_md_access:PASS: 277 nsec
Summary: 30 PASSED, 0 FAILED
[root@s8360046 bpf]#

Fixes: 18f3d6be ("selftests/bpf: Add test cases to test narrower ctx field loads")
Signed-off-by: NThomas Richter <tmricht@linux.vnet.ibm.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The existing sub channel code did not wait for all the sub-channels
to completely initialize. This could lead to race causing crash
in napi_netif_del() from bad list. The existing code would send
an init message, then wait only for the initial response that
the init message was received. It thought it was waiting for
sub channels but really the init response did the wakeup.

The new code keeps track of the number of open channels and
waits until that many are open.

Other issues here were:
  * host might return less sub-channels than was requested.
  * the new init status is not valid until after init was completed.

Fixes: b3e6b82a ("hv_netvsc: Wait for sub-channels to be processed during probe")
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull x86 platform driver fix from Darren Hart:
 "Fix loop preventing some platforms from waking up via the power button
  in s2idle:

   - intel-vbtn: match power button on press rather than release"

* tag 'platform-drivers-x86-v4.13-4' of git://git.infradead.org/linux-platform-drivers-x86:
  platform/x86: intel-vbtn: match power button on press rather than release