Instead of enabling the watchdog in each individual dts file, select in
the SoC dtsi file instead.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add alias for gpio nodes, so that gpio driver can identify the port
number and then specify a sensible gpio base rather than using the
one dynamically allocated by gpio core.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Some mxc processors have an edge_sel feature, which allows the IRQ to be
triggered by any edge.

This patch makes use of this feature if available, which skips mxc_flip_edge().

Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: NSascha Hauer <kernel@pengutronix.de>
Cc: <linux-arm-kernel@lists.infradead.org>
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Imx6q sabrelite board uses ecspi1 to connect a spi flash sst25vf016b,
we need to add pinctrl information for it in the dts, otherwise the
ecspi1 driver can't work and the connected flash is wrongly
detected as a mr25h256 flash like this:

m25p80 spi32766.0: found mr25h256, expected sst25vf016b
m25p80 spi32766.0: mr25h256 (32 Kbytes)

Cc: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: NHui Wang <jason77.wang@gmail.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

- add usbphy devices
- add usb host controller and otg devices
- add usb h1 vbus regulator
Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Change the value of #interrupt-cells of gpio nodes from 1 to 2, so that
the gpio irq type can be specified in device tree.  Also update binding
document to make it clear.
Reported-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add the DT node for gpmi nand.
Add the pinmux support for gpmi nand.

The gpmi nand may conflicts with other modules, such as MMC.
So we do not enable the gpmi nand for mx6q-arm2 board, just add the
node for the board.
Acked-by: NDong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: NHuang Shijie <shijie8@gmail.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

add DT node for apbh-dma.
Signed-off-by: NHuang Shijie <shijie8@gmail.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NRichard Zhao <richard.zhao@linaro.org>
Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NRichard Zhao <richard.zhao@linaro.org>
Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Signed-off-by: NDong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

It has been pointed out by device tree maintainer for several times
that the generic names 'serial' and 'ethernet' should be used for
those devices per ePAPR.  Renames imx uart and fec device tree nodes
to stop them being bad examples.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>

Add anatop regulators to imx6q.dtsi for all imx6q platforms.
Signed-off-by: NYing-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Signed-off-by: NRichard Zhao <richard.zhao@linaro.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add support for the new smp_twd runtime registration interface
to the imx6q platforms, and remove the old compile-time support.

The imx6q DTS file is updated to match the TWD DT documentation.
Also present in this patch a DTS fix to the timer interrupt routing
(the PPI connection uses bits [15:8]) and trigger (rising edge).
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

UART1/UART2/... is more readable than UART0/UART1/... .
Remove redundant UART comments.
Signed-off-by: NRichard Zhao <richard.zhao@linaro.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

GPIO1/GPIO2/... is more readable than GPIO0/GPIO1/... .
Remove redundant gpio comments.
Signed-off-by: NRichard Zhao <richard.zhao@linaro.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

It adds device tree source and documentation for imx6q platform.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>