We need to have a station and a queue for the monitor
interface to be able to inject traffic. We used to have
this traffic routed to the auxiliary queue, but this queue
isn't scheduled for the station we had linked to the
monitor vif.

Allocate a new queue, link it to the monitor vif's station
and make that queue use the BE fifo.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=196715

Cc: stable@vger.kernel.org
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

There is a macro for converting TX response rate to a
rate scale value, use it.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

locking/atomics: COCCINELLE/treewide: Convert trivial ACCESS_ONCE() patterns to READ_ONCE()/WRITE_ONCE()

Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.

For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.

However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:

----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()

// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch

virtual patch

@ depends on patch @
expression E1, E2;
@@

- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)

@ depends on patch @
expression E;
@@

- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.comSigned-off-by: NIngo Molnar <mingo@kernel.org>

In the compressed BA notif, the driver didn't parse out
the LQ color, so statistics for the rates tried were
always thrown out. Add it so it gets correctly used.

While at it, fix the name of the relevant field in the
struct.

Fixes: c46e7724 ("iwlwifi: mvm: support new BA notification response")
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

AP interfaces now send all non-bufferable frames using the broadcast
station. Thus allow them to use the probe queue and don't warn about
it.

Fixes: eb045e6e ("iwlwifi: mvm: Avoid deferring non bufferable frames")
Signed-off-by: NAvraham Stern <avraham.stern@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When we flush a queue, the packets will have a 'failed'
status but we shouldn't send a BAR. This check was missing.
Because of that, when we got an ampdu_action with
IEEE80211_AMPDU_TX_STOP_FLUSH, we started the following
ping pong with the firmware:

1) Set the station as 'draining'
2) Get a failed Tx status (DRAINED)
3) Send a BAR because of the failed Tx status

(loop of 2 and 3)

This loop wasn't endless since the BAR isn't sent on a
queue that would trigger a "nested" BAR.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The firmware team is now re-using a bit that hasn't been
used for a few generations. Re-use for TX_ON_AIR drop.
This bit will be set by the firmware to indicate that
a frame in an A-MPDU was dropped but not because of the
already mapped reasons.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

All the firmware versions the driver supports enable DQA, and thus
the only way to get non-DQA mode is to modify the source. Remove
this mode to simplify the code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The FIFO numbering is different in A000 devices. This
means that we routed BE packets to BK FIFO. Fix this.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Split out the firmware debug code to be more general, so that it
can be used by different subdrivers.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Refactor the shared memory command parsing into common code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The bit was set only if there was at least one reclaimed frame in an
aggregation. It's important to set it also in the case that the whole
A-MPDU was lost, otherwise rate scaling statistics will not be
updated correctly. Thus, set it always in ba notification handler.

This fixes a throughput degradation of about 20% in certain scenarios
with multiple streams on 11ac.
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When we enabled TCP checksum offload, we need to tell the
firmware where the IP header starts. If we have an IV, then
we need to adapt that value since the IV is placed before
the SNAP header. This is true only for cases where the
driver adds the IV, not the WEP case in which the IV is
added by the firmware itself.

On A000 devices series, the IV is always added by the
device.

Fix this.

Fixes: 5e6a98dc ("iwlwifi: mvm: enable TCP/UDP checksum support for 9000 family")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When a station that's not associated sends a data frame (e.g. an NDP)
hostapd will respond with a disassoc frame, telling it that it's not
associated. The station might also not be authenticated, in which case
there will not be a station entry for it, and as a result we need to
accept such frames without a station.

Fixes: 3ee0f0e2 ("iwlwifi: mvm: fix DQA AP mode station assumption")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When we get a non-STA frame to transmit in client mode, we try to use
the IWL_MVM_DQA_BSS_CLIENT_QUEUE queue (queue #4). However, at this
point, the queue might not be allocated at all, causing warnings. The
scenario on which this happened was a race condition between mac80211
and our queue allocation work:
 * mac80211 sends auth
 * we stop mac80211 queues to allocate a hw queue
 * authentication is aborted
 * we allocate HW queue and start mac80211 queues
 * mac80211 removes station
 * mac80211 hands us the auth frame from the pending queue

At this point, since mac80211 has already removed the station, we try
to transmit the frame through this special non-station case on queue
4 anyway.

In order to really use it properly, we'd have to again go through the
hw queue allocation work, and attach it to a station, etc. In this
case that isn't possible (there's no station anymore), but if this
special case were needed, then we'd have to do it this way.

However, the special case is documented to exist for TDLS, but can't
trigger there because the TDLS setup frames etc. are normal to-DS
frames going to the peer through the AP. Testing also confirms that
this code path isn't triggered in TDLS.

Therefore, remove the code path to avoid using an unused queue. The
erroneous frame described above will still be transmitted on the AUX
queue, but arguably that's a mac80211 problem, which will eventually
be fixed by moving everything there to TXQs.

Fixes: e3118ad7 ("iwlwifi: mvm: support tdls in dqa mode")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When we get large sends on non-QoS association, we had a
bug that mangled the SNAP header. Fix that.

Fixes: a6d5e32f ("iwlwifi: mvm: send large SKBs to the transport")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Getting the TID of a packet before we know it is a QoS data
packet isn't a good idea. Delay the TID retrieval until
we know the packet is a QoS data packet.

Fixes: bb81bb68 ("iwlwifi: mvm: add Tx A-MSDU inside A-MPDU")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

There may be a difference between the mac80211 vif->cab_queue and
mvmvif->cab_queue, particularly with TVQM. Make the code map this
earlier, instead of first returning the mac80211 one again from
iwl_mvm_get_ctrl_vif_queue().
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The code was intended to enable IP header checksumming on AMSDUs, but
failed to really do so because the A-MSDU bit was set after all the
checksumming bits, and thus checking for A-MSDU could never be true.

Fix this by setting the A-MSDU bit before the offload bits.

Fixes: 5e6a98dc ("iwlwifi: mvm: enable TCP/UDP checksum support for 9000 family")
Reported-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When hostapd adds a station, it does so before sending the association
response frame, so that it can indicate the correct status code in the
response.

However, when this then fails, or the association response already is
a reject for some other reason, then there's no station entry and thus
no per-station management queue to send the response on and it must be
sent on the probe response queue. The code should therefore not warn.

In theory, we could check and warn if the status code is success, but
that seems excessive, so just relax the check to allow any association
response frames.

Fixes: 3ee0f0e2 ("iwlwifi: mvm: fix DQA AP mode station assumption")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When receiving a BA_NOTIF on new TX API, it can
contain BAs for several TIDs. Go over them and
reclaim TX for every TID.

Note that although the small API change, the API
version still isn't bumped forward, as this NIC
isn't still officially released.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When trying to TX through a monitor interface, the
conditions in iwl_mvm_tx_skb_non_sta() don't match
and the frame tries to go out from an usued TXQ.

Add a check for monitor iface, and use the AUX queue
in such a case.

In non-DQA mode the frame is sent through the
static-allocated queues anyway, so the problem is
in DQA mode only.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This new API allows flushing queues based on station ID and TID in A000
devices.  One reason for using this is that tfd_queue_mask is only good
for 32 queues, which is not enough for A000 devices.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NMordechai Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This improves documentation, since kernel-doc can't deal with the
union well.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

On A000 HW, the SCD rdptr has only 8 bits allocated
for it, thus when checking if a queue is full, or
when checking if the SSN is equal to the TID's
next_reclaimed, A000 HW should trim the SSN.

Fix this by "normalizing" the SSN to wrap around
0xFF when comparing to the next_reclaimed on A000
HW.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Avoid one kind of symbol shadowing another in iwl_mvm_flush_sta()
by renaming the function parameter.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When sending a Tx Command with a Tx packet, we allocate the
Tx command separately from the payload of the packet.
The WiFi MAC header is then copied into the buffer that was
allocated for the Tx Command. This means that this buffer
needs to be big enough to contain both. This is why it is
allocated with iwl_trans_alloc_tx_cmd which returns a
pointer to a newly allocated not zeroed struct
iwl_device_cmd.

The Tx command has a few bit fields and hence it needs to
be zeroed, but all the rest of the buffer doesn't need to
be zeroed since it will either be memcopy'ed with the MAC
header, or not even sent to the device.
This means that we don't need to zero all the
iwl_device_cmd structure, but rather only the size of
the iwl_tx_cmd structure.

Since sizeof(iwl_tx_cmd) - sizeof(iwl_tx_cmd) is about
260 bytes, this can avoid touching 4 cache lines for each
packet.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Enable offload assist for AMSDU when the AMSDU present flag is set.

Fixes: a830baba9c2e ("iwlwifi: mvm: support new TX API")
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Up until now, the driver was comparing the rate reported by the FW and
the rate of the latest LQ command to avoid processing data belonging
to the old LQ command. Recently, FW changed the meaning of the initial
rate field in tx response and it holds the actual rate (which is not
necessarily the initial rate of LQ's rate table). Use instead LQ cmd
color to be able to filter out tx responses/BA notifications which
where sent during earlier LQ commands' time frame.

This fixes some throughput degradation in noisy environments.
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

There's no point to declare an address as a __le32/__le16
and then only take a pointer to it anyway, change that to
just a sta_addr[ETH_ALEN].
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Avoid using the global flush and move to flush per
station whenever possible in DQA mode.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Most of the fields aren't needed in new TX path.
Enlarging the struct to 512 queues will consume a lot of memory.
Remove all references to the struct in the new TX path.
Move mac80211 queue mapping outside, since it will be needed per
queue for TVQM mode.
Add warning in paths that shouldn't be hit.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We can't use IEEE80211_INVAL_HW_QUEUE to mark a queue as
invalid since 255 will be a valid value for a TVQM queue
index.
Use IWL_MVM_INVALID_QUEUE instead for accessing txq_id.
reserved_queue can stay a u8 since reserved_queue is not
used when TVQM is enabled.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

cab_queue can now get bigger than u8, since in TVQM we will support
512 queues..
Support it by maintaining internal mapping between the actual number
and mac80211 queue (IWL_MVM_DQA_GCAST_QUEUE).
For pre-a000 the internal queue will be the same as the mac80211
queue.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When FW fails to get block ack, it will send the notification with
0 items in the TFD queue elements. Allow this and handle accordingly.

Fixes: c46e7724 ("iwlwifi: mvm: support new BA notification response")
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

API was changed once more to support 2 LMACs.
Adapt to change while preserving current functionality.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In TVQM mode the TX responses were changed to include
queue number since legacy TX queue number retrieval cannot
be scaled up to 512 queues.
Support this change.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

For a000 FW moved to 15 as management TID.
The change for us is fairly local - translate old TID to 15
when enabling and disabling a queue, and make sure to cover
it also on TX responses.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

a000 devices queue management is going to change significantly.
We will have 512 queues. Those queues will be assigned number
by the firmware and not by the driver.

In addition, due to SN offload having TX queue shared between TIDs
is impossible

Also, the ADD_STA command no longer updates queues status.
The only point of changing queue in the SCD queue config API.

From driver perspective we have here a new design:

Queue sharing and inactivity checks are disabled.

Once this is done, the only paths that call scd_queue_cfg command
are paths that alloc and release TX queues - which will make future
accommodation to queue number assignment by FW easier.
Since allocating 512 queues statically is not advisable, transport
will allocate the queue on demand, fill the command with DRAM data
and send it. This is reflected in the new transport API.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Support the new TX command API for a000 devices.
Command is a very slim version of current TX command.
Generalize iwl_mvm_tx_mpdu to get rid of TX command dependencies.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>