Add comments describing the platform data members
and per-chip-select SPI configuration structure.

Also, add some comments describing the what happens
during the driver probe.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Setup the owner member of the platform driver to THIS_MODULE
instead of leaving it NULL.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Enable SPI only when active transfers are in progress. Keep
it in local low power when not in use.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

The "clk_internal" platform data member which contols the
CLKMOD bit in Global Control Register 1 is not useful
since CLKMOD needs be set to 1 *always* to ensure master
mode operation.

Remove this platform data.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Let DMA operation be specified on a per-device basis instead
of selecting it once during probe.

A side effect of this is the need to combine the PIO and DMA buffer
txrx_bufs routine. This is good since they anyway share some common
functionality.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

The DMA code does not use the existing completion variable 'done'
which is being used for interrupt mode transfers. Instead it uses
two different completion variables specific to DMA mode transfers.

Eliminate the usage of new completion variables for DMA mode and
use the existing completion variable.

[nsekhar@ti.com: To make this process easy, eliminate the two
different DMA completion callback functions for tx and rx and
use a single callback function instead]
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Do not simply clean the DMA channel on a DMA completion
error. Instead, use wcount and rcount members of davinci_spi
to detecion non-completion of DMA and signal EIO to the
application.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Use a dummy param slot linked to itself to take care of the
extra "sync event" that gets sent to EDMA controller after
the last byte has been transferred.

The dummy PaRAM slot that is linked to the actual DMA PaRAM
slot "absorbs" this event and prevents a EDMA CC error to
be asserted.

Without this provision, the EDMA CC error would be asserted
because the channel PaRAM would be empty after the transfer
and EDMA would not know what to make out of the extra sync
event.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Do not allocate (and de-allocate) SPI DMA channels during setup
(and cleanup) for each SPI device. Instead, allocate the DMA
channels once duing probe and use them for the life time of
the driver.

This makes sense since there are dedicated DMA channels meant
for SPI use.

This also helps remove the unnecessary DMA "sync_dev" variables
being used to store DMA channel information.

Also, the "use_dma" platform variable is now eliminated since
it is possible to check if the platform supports DMA or not
based upon whether DMA resources can be found or not.
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Tested-By: NBrian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Do not stop SPI DMA event generation in either transmit or
receive DMA event call back because the single setting affects
both transmit and receive event generation.

Depending on the order in which the callbacks happen, transmit
or receive events can get unintentionally stalled.

Instead, disable event generation once after both the transmit
and receive DMA completes.

While at it, remove the largely under-used function to set or
clear DMA event generation.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Currently a series of EDMA API calls are being made to setup
various aspects of EDMA PaRAM slots for receive and transmit.

Instead setup the PaRAM using a local structure and write once
to the hardware using edma_write_slot()
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

In keeping with the full duplex nature of the SPI bus. Always
start receive DMA along with transmit DMA.

If there is no receive buffer provided with the transfer, use
a temporary buffer to receive the data to be thrown away.

[michael.williamson@criticallink.com: receive DMA size should
be same as transfer length to avoid hang-up when transfer length
is smaller than temporary rx buffer size (rx buffer not provided)]
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Remove usage of temporary buffer when no transmit data is provided.
Instead, use the transmit register itself as the source of data.

By choosing the transmit register itself as the source of data, this
patch helps remove unnecessary accesses to memory when no real data
is being transmitted.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Due to the full duplex nature of the SPI bus, the SPI master
on DaVinci needs transmit to be active even if the tranfer is
only meant to collect receive data.

The current code achieves this by using a temporary zeroed buffer
to provide DMA data in case the transfer does not have a transmit
buffer provided.

However, the transmit DMA is started only if transmit buffer is
provided rendering the temporary buffer unused. Instead the code
relies on a write to SPIDAT1 register to trigger transmit operation.
This however only sends two bytes of data.

Fix this by starting transmit DMA always.

This changes exposes a bug on DM355 where the CSHOLD bit in
SPIDAT1 needs to be written to in between transfers. Handle
that by introducing a "cshold_bug" platform data which is
set to true for DM355.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Do not store DMA channel related information per chip-select since
that information does not depend on the chip select.

The same DMA channels can be used for transfers on all chip-selects
since the transfer happens one-at-a-time.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Remove unnecessary call to davinci_spi_setup_transfer() at the end
of davinci_spi_setup().

davinci_spi_setup_transfer() is registered as the setup_transfer
callback for the bitbang layer and is called independently by
the bitbang layer to setup the transfer before it begins.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

The function davinci_spi_bufs_prep() is doing stuff that
davinci_spi_setup() is doing. Eliminate it and move the work
to davinci_spi_setup()
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Configure the data-in, data-out and clock functionality pins
in SPIPC0 register only once during probe. No need to set these
bits for each transfer.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Add support for SPI interrupt mode operation.

Define a per chip-select "io type" variable which
specifies if the transfers on this chip-select should
happen in interrupt mode or polled mode.

Introduce a new function davinci_spi_process_events()
to help consolidate the code between interrupt mode
processing and polled mode processing.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Use the fact that the get_tx and get_rx can now cope with
NULL buffer pointers to simplify the poll mode transfer
code.

While at it, check for SPI errors every transfer rather than
at the end of the whole transfer.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

The interrupt mode support as it stands is another version
of poll mode. Even when interrupt mode is selected, the code
tight loops on interrupt status register, rendering it totally
useless. A completion variable is initialized, but never used.

Remove this fake interrupt mode since users can anyway use
poll mode with no functional difference. A usefully implemented
interrupt mode support can be added later.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

The completion variable 'done' is unnecessarly initialized by
the function davinci_spi_bufs_dma() where as it is not used
for DMA transfers at all.

Remove the unnecessary initialization.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

In davinci_spi_check_error(), Tx interrupt being set is
treated as error. This function is only meant to flag
bus error conditions and Tx interrupt being set at that
point is not a bus error but rather a driver bug.

Stop checking for Tx interrupt and flagging that as an
IO error.
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Tested-By: NBrian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

The variable count in DaVinci SPI driver's private data is
largely unused and its minor use can easily be eliminated.

Remove the variable.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

In the davinci_spi_bufs_dma() function, SPI is briefly disabled
before enabling it immediately back again.

Remove this unnecessary disable.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

In the davinci_spi_{tx|rx}_u{8|16}() functions, check for
buffer pointer being valid before using it. While providing
for better error checking, this change will help simplify
code in the caller.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

The EDMA acount (called data_type in davinci_spi_bufs_dma())
is simply the bytes_per_word obtained in the transfer setup
function. The current code calculates the acount value from
bytes_per_word in a convoluted manner. Simplify the code.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

The count member of davinci_spi is internal to the driver and
is not shared with framework. Eliminate its unnecessary update.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

The struct davinci_spi_slave has a single member. Eliminate it
and store the per-chipselect data in struct davinci_spi directly.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Several members of struct davinci_spi_slave are unused in code.
Remove such members.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Just enabling WAITENA in SPIFMTn register waits for the
enable signal from the slave indefinitely. Allow support
for finite waiting by adding support for c2e delay
(maximum time for addressed slave to respond) and t2e
delay (maximum time for slave to respond after transmit
data finished).

While at it, modify the T2C and C2T defines by prepending
the register name as is the convention followed for other
register field elsewhere in the driver.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Setup chip-select timers values only if timer is enabled
(timer_disbled in spi configuration is false).

As a nice side effect, this patch removes code duplicated in
davinci_spi_bufs_pio() and davinci_spi_bufs_dma().
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Consolidate the setup of SPIFMTn register under
davinci_spi_setup_transfer() simplifying the code
and avoiding unnecessary reads and writes to the
register.

The two inline functions {set|clear}_fmt_bits() can
be eliminated because of this.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Some chip-select specific paramterers like wdelay, parity, usage of
chip-select timers (and the actual timer values) are included in
platform data forcing the same behaviour across all chip-selects.

Create a new davinci_spi_config data structure which can be passed
along using controller_data member of spi_device data structure
on a per-device basis.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

The SPI_READY bit of struct spi_device:mode serves the purpose
of letting the SPI master know if the slave can signal if it is
ready for transfer or not.

The 'wait_enable' platform data was duplicating this functionality.
Use the framework provided method of indicating this capability.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Simplify pre-scalar calculation and move it into a seprate
function.

Refuse to correct invalid pre-scalar values silently as this
might lead to unexpected bugs and lower performance. Instead
an error will force users to dig into the root-cause of the
issue.

While at it, remove some device specific checks on the maximum
SPI frequency. As the driver supports the SPI interface
implemented on various devices, it should only take care of core
SPI limitations and leave the device specific handling to platform
code.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Sometimes, the chip selects provided by SPI module are
muxed with other functionality and cannot be used in
some designs. In such cases, it becomes convenient to use
an available GPIO line as chip select.

This patch enables the DaVinci SPI driver to treat specific
GPIO lines as chip selects based on information provided in
platform data.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

On TI DaVinci's SPI controller, the SPIDAT1 register which
controls the chip slect status, also has data transmit register
in the lower 16 bits. Writing to the whole 32-bits triggers
an additional data transmit every time the chip select is disabled.

While most SPI slaves cope-up with this, some cannot. This
patch fixes this by doing a 16-bit write on the upper half
of the SPIDAT1 register

While at it, group the SPIGCR1 register related defines seperately
from SPIDAT1 register defines.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Let davinci_spi_chipselect() perform both activation and
deactivation of chip selects. This lets spi_bitbang fully
control chip select activation, as intended by the SPI API.

With this change, the chip select activation code need not
be duplicated in davinci_spi_bufs_{pio|dma}().

Also, keeping chip select active control is removed as a
platform data and simply controlled using information from
spi_bitbang on whether chip slect should be activated or
de-activated.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Quit writing the same constant value determining the chip-select
mode when no transmissions are in progress in davinci_spi_chipelect().

Instead just setup the SPIDEF register once during probe.
Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: NMichael Williamson <michael.williamson@criticallink.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>