This patch adds support to the dsa slave network device so that
switch drivers can implement the SIOC[GS]HWTSTAMP ioctls and the
ethtool timestamp-info interface.
Signed-off-by: NBrandon Streiff <brandon.streiff@ni.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support for enabling the internal PHY for a 'cpu' port.
It has been tested on GE B850v3,  B650v3 and B450v3, which have a
built-in MV88E6240 switch hardwired to a PCIe based network card.
On these machines the internal PHY of the i210 network card and
the Marvell switch are connected to each other and must be enabled
for properly using the switch. While the i210 PHY will be enabled
when the network interface is enabled, the switch's port is not
exposed as network interface. Additionally the mv88e6xxx driver
resets the chip during probe, so the PHY is disabled without this
patch.
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of having the different master network device drivers
potentially used by DSA/Broadcom tags, move the padding necessary for
the switches to accept short packets where it makes most sense: within
tag_brcm.c. This avoids multiplying the number of similar commits to
e.g: bgmac, bcmsysport, etc.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need to make the dsa_legacy_register() stub return 0 in order for
dsa_init_module() to successfully register and continue registering the
ETH_P_XDSA packet handler.

Fixes: 2a93c1a3 ("net: dsa: Allow compiling out legacy support")
Reported-by: NEgil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to let MT7530 switch can recognize well those egress packets
having both special tag and VLAN tag, the information about the special
tag should be carried on the existing VLAN tag. On the other hand, it's
unnecessary for extra handling for ingress packets when VLAN tag is
present since it is able to put the VLAN tag after the special tag and
then follow the existing way to parse.
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These duplicate includes have been found with scripts/checkincludes.pl but
they have been removed manually to avoid removing false positives.
Signed-off-by: NPravin Shedge <pravin.shedge4linux@gmail.com>
Acked-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce a configuration option: CONFIG_NET_DSA_LEGACY allowing to compile out
support for the old platform device and Device Tree binding registration.
Support for these configurations is scheduled to be removed in 4.17.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tcfm_dev always points to the correct netdev and we already
hold a refcnt, so no need to use tcfm_ifindex to lookup again.

If we would support moving target netdev across netns, using
pointer would be better than ifindex.

This also fixes dumping obsolete ifindex, now after the
target device is gone we just dump 0 as ifindex.

Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DSA ports also need to have a dedicated CPU port assigned to them,
because they need to know where to egress frames targeting the CPU,
e.g. To_Cpu frames received on a Marvell Tag port.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a MAC address is added to or removed from a switch port in the
fabric, the target switch must program its port and adjacent switches
must program their local DSA port used to reach the target switch.

For this purpose, use the dsa_towards_port() helper to identify the
local switch port which must be programmed.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch brings no functional changes.
It moves out the MDB code iterating on a multicast group into new
dsa_switch_mdb_{prepare,add}_bitmap() functions.

This gives us a better isolation of the two switchdev phases.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch brings no functional changes.
It moves out the VLAN code iterating on a list of VLAN members into new
dsa_switch_vlan_{prepare,add}_bitmap() functions.

This gives us a better isolation of the two switchdev phases.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The DSA switch MDB ops pass the switchdev_trans structure down to the
drivers, but no one is using them and they aren't supposed to anyway.

Remove the trans argument from MDB prepare and add operations.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The DSA switch VLAN ops pass the switchdev_trans structure down to the
drivers, but no one is using them and they aren't supposed to anyway.

Remove the trans argument from VLAN prepare and add operations.

At the same time, fix the following checkpatch warning:

    WARNING: line over 80 characters
    #74: FILE: drivers/net/dsa/dsa_loop.c:177:
    +				      const struct switchdev_obj_port_vlan *vlan)
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Setting the refcount to 0 when allocating a tree to match the number of
switch devices it holds may cause an 'increment on 0; use-after-free',
if CONFIG_REFCOUNT_FULL is enabled.

To fix this, do not decrement the refcount of a newly allocated tree,
increment it when an already allocated tree is found, and decrement it
after the probing of a switch, as done with the previous behavior.

At the same time, make dsa_tree_get and dsa_tree_put accept a NULL
argument to simplify callers, and return the tree after incrementation,
as most kref users like of_node_get and of_node_put do.

Fixes: 8e5bf975 ("net: dsa: simplify tree reference counting")
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Tested-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The lan9303 set bits in the host CPU tag indicating if a ingress frame
is a trapped IGMP or STP frame. Use these bits to calculate
skb->offload_fwd_mark more efficiently.
Signed-off-by: NEgil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DSA now uses one of the symbols exported by the bridge,
br_vlan_enabled(). This has a stub, if the bridge is not
enabled. However, if the bridge is enabled, we cannot have DSA built
in and the bridge as a module, otherwise we get undefined symbols at
link time:

   net/dsa/port.o: In function `dsa_port_vlan_add':
   net/dsa/port.c:255: undefined reference to `br_vlan_enabled'
   net/dsa/port.o: In function `dsa_port_vlan_del':
   net/dsa/port.c:270: undefined reference to `br_vlan_enabled'
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new type: DSA_TAG_PROTO_PREPEND which allows us to support for the
4-bytes Broadcom tag that we already support, but in a format where it
is pre-pended to the packet instead of located between the MAC SA and
the Ethertyper (DSA_TAG_PROTO_BRCM).
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for supporting the same Broadcom tag format, but instead
of inserted between the MAC SA and EtherType, prepended to the Ethernet
frame, restructure the code a little bit to make that possible and take
an offset parameter.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A number of drivers want to check whether the configured CPU port is a
possible configuration for enabling tagging, pass down the CPU port
number so they verify that.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that IGMP packets no longer is flooded in HW, we want the SW bridge to
forward packets based on bridge configuration. To make that happen,
IGMP packets must have skb->offload_fwd_mark = 0.
Signed-off-by: NEgil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The software bridge needs to know if a packet has already been bridged
by hardware offload to ports in the same hardware offload, in order
that it does not re-flood them, causing duplicates. This is
particularly true for broadcast and multicast traffic which the host
has requested.

By setting offload_fwd_mark in the skb the bridge will only flood to
ports in other offloads and other netifs. Set this flag in the DSA and
EDSA tag driver.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SWITCHDEV_ATTR_ID_PORT_PARENT_ID is used by the software bridge when
determining which ports to flood a packet out. If the packet
originated from a switch, it assumes the switch has already flooded
the packet out the switches ports, so the bridge should not flood the
packet itself out switch ports. Ports on the same switch are expected
to return the same parent ID when SWITCHDEV_ATTR_ID_PORT_PARENT_ID is
called.

DSA gets this wrong with clusters of switches. As far as the software
bridge is concerned, the cluster is all one switch. A packet from any
switch in the cluster can be assumed to have been flooded as needed
out of all ports of the cluster, not just the switch it originated
from. Hence all ports of a cluster should return the same parent. The
old implementation did not, each switch in the cluster had its own ID.

Also wrong was that the ID was not unique if multiple DSA instances
are in operation.

Use the tree ID as the parent ID, which is the same for all switches
in a cluster and unique across switch clusters.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current code does not return after successfully preparing the VLAN
addition on every ports member of a it. Fix this.

Fixes: 1ca4aa9c ("net: dsa: check VLAN capability of every switch")
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current code does not return after successfully preparing the MDB
addition on every ports member of a multicast group. Fix this.

Fixes: a1a6b7ea ("net: dsa: add cross-chip multicast support")
Reported-by: NEgil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The software bridge can be build with vlan filtering support
included. However, by default it is turned off. In its turned off
state, it still passes VLANs via switchev, even though they are not to
be used. Don't pass these VLANs to the hardware. Only do so when vlan
filtering is enabled.

This fixes at least one corner case. There are still issues in other
corners, such as when vlan_filtering is later enabled.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that the host indicates when a multicast group should be forwarded
from the switch to the host, don't do it by default.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The notify mechanism does not need to modify the port it is notifying.
So make the parameter const.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add code to handle switchdev host mdb add/del. Since DSA uses one of
the switch ports as a transport to the host, we just need to add an
MDB on this port.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit brings no functional changes. It gets rid of the underscore
prefixed _dsa_register_switch and _dsa_unregister_switch functions in
favor of dsa_switch_probe() which parses and adds a switch to a tree and
dsa_switch_remove() which removes a switch from a tree.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that the tree setup is centralized, we can simplify the code a bit
more by setting up or tearing down the tree directly when adding or
removing a switch to/from it.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The *_complete() functions take too much arguments to do only one thing:
they try to fetch the dsa_port structures corresponding to device nodes
under the "link" list property of DSA ports, and use them to setup the
routing table of switches.

This patch simplifies them by providing instead simpler
dsa_{port,switch,tree}_setup_routing_table functions which return a
boolean value, true if the tree is complete.

dsa_tree_setup_routing_table is called inside dsa_tree_setup which
simplifies the switch registering function as well.

A switch's routing table is now initialized before its setup.

This also makes dsa_port_is_valid obsolete, remove it.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The OF code provides a of_for_each_phandle() helper to iterate over
phandles. Use it instead of arbitrary iterating ourselves over the list
of phandles hanging to the "link" property of the port's device node.

The of_phandle_iterator_next() helper calls of_node_put() itself on
it.node. Thus We must only do it ourselves if we break the loop.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of having two dsa_ds_find_port_dn (which returns a bool) and
dsa_dst_find_port_dn (which returns a switch) functions, provide a more
explicit dsa_tree_find_port_by_node function which returns a matching
port.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dsa_dsa_port_apply and dsa_cpu_port_apply functions do exactly the
same. The dsa_user_port_apply function does not try to register a fixed
link but try to create a slave.

This commit factorizes and scopes all that in two convenient
dsa_port_setup and dsa_port_teardown functions.

It won't hurt to register a devlink_port for unused port as well.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patches brings no functional changes. It removes the unused dst
argument from the dsa_ds_apply and dsa_ds_unapply functions, rename them
to dsa_switch_setup and dsa_switch_teardown for a more explicit scope.

This clarifies the steps of the setup or teardown of a switch fabric.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit provides better scope for the DSA tree setup and teardown
functions. It renames the "applied" bool to "setup" and print a message
when the tree is setup, as it is done during teardown.

At the same time, check dst->setup in dsa_tree_setup, where it is set to
true.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add DSA helpers to setup and teardown a master net device wired to its
CPU port. This centralizes the dsa_ptr assignment.

This also makes the master ethtool helpers static at the same time.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dsa_dst_parse function called just before dsa_dst_apply does not
parse the tree but does only one thing: it assigns the default CPU port
to dst->cpu_dp and to each user ports.

This patch simplifies this by calling a dsa_tree_setup_default_cpu
function at the beginning of dsa_dst_apply directly.

A dsa_port_is_user helper is added for convenience.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A DSA port has a dedicated CPU port assigned to it, stored in the cpu_dp
member. It is not meant to be modified by a port, thus make it const.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>