In case of SGMII more, for example when a MAC2MAC connection
is needed, the port selection bits (inside the MAC configuration
registers) have to be programmed according to the link selected.
So the patch adds a new DT parameter to pass the port selection
and to programmed related PCS and CORE to use it.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By default, all gmac cores disable the PCS block and always
enable the PMT.

Note that this is done in a different way by 3.x and 4.x cores.

With this rework, PCS and PMT interrupt masks can be driven by
parameters now moved inside the mac_device_info structure
and the settings follow what the HW capability register reports.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 3.xx and 4.xx synopsys gmacs have a very similar
PCS embedded module and they share almost the same registers:
for example:
  AN_Control, AN_Status, AN_Advertisement, AN_Link_Partner_Ability,
  AN_Expansion, TBI_Extended_Status.

Just the RGMII/SMII Control/Status register differs.

So This patch aims to reorganize and enhance the PCS support.
It removes the existent support from the dwmac1000/dwmac4_core.c
moving basic PCS functions inside a new file called: stmmac_pcs.h.

The patch also reviews the available APIs to be better shared among
different hardware and easily enhanced to support new features.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Calling the fixed-phy functions when CONFIG_FIXED_PHY=m as a previous
change tried cannot work if the caller is in built-in code:

drivers/of/built-in.o: In function `of_phy_register_fixed_link':
of_reserved_mem.c:(.text+0x85e0): undefined reference to `fixed_phy_register'

Making of_mdio depend on 'FIXED_PHY || !FIXED_PHY' would solve this
dependency by enforcing that OF_MDIO itself becomes a loadable module
when FIXED_PHY=y, but that creates a different dependency as it
breaks any built-in ethernet driver that uses of_mdio.

Making FIXED_PHY a bool option also cannot work, since it depends on
PHYLIB, which again is tristate.

This version now uses 'select FIXED_PHY' to ensure that the fixed-phy
portion of of_mdio is not optional. The main downside of this is
a small increase in code size for cases that do not need fixed phy
support, but it should avoid all of the link-time problems.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: d1bd330a ("of_mdio: Enable fixed PHY support if driver is a module")
Acked-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drop redundant include of moduleparam.h

The Coccinelle semantic patch used to make this change is as follows:
@ includesmodule @
@@

#include <linux/module.h>

@ depends on includesmodule @
@@

- #include <linux/moduleparam.h>
Signed-off-by: NAmitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to inet_diag facility to filter sockets based on device
index. If an interface index is in the filter only sockets bound
to that index (sk_bound_dev_if) are returned.
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Russell King says:

====================
Initial SFP support patches

Please review and merge this initial patch set, which is part of a
larger set previously posted adding SFP support to phy and mvneta.

This initial set are focused on cleaning up and reorganising the
fixed-phy code to allow the core software-phy code to be re-used.

These are based on net-next.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no prevention of a concurrent call to both fixed_mdio_read()
and fixed_phy_update_state(), which can result in the state being
modified while it's being inspected.  Fix this by using a seqcount
to detect modifications, and memcpy()ing the state.

We remain slightly naughty here, calling link_update() and updating
the link status within the read-side loop - which would need rework
of the design to change.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Generate software phy registers as and when requested, rather than
duplicating the state in fixed_phy.  This allows us to eliminate
the duplicate storage of of the same data, which is only different
in format.

As fixed_phy_update_regs() no longer updates register state, rename
it to fixed_phy_update().
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Separate out the generation of MII registers from the state validation.
This allows us to simplify the error handing in fixed_phy() by allowing
earlier error detection.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert the swphy register generation to tabular form which allows us
to eliminate multiple switch() statements.  This results in a smaller
object code size, more efficient, and easier to add support for faster
speeds.

Before:

Idx Name          Size      VMA       LMA       File off  Algn
  0 .text         00000164  00000000  00000000  00000034  2**2

   text    data     bss     dec     hex filename
    388       0       0     388     184 swphy.o

After:

Idx Name          Size      VMA       LMA       File off  Algn
  0 .text         000000fc  00000000  00000000  00000034  2**2
  5 .rodata       00000028  00000000  00000000  00000138  2**2

   text    data     bss     dec     hex filename
    324       0       0     324     144 swphy.o
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the fixed_phy MII register generation to a library to allow other
software phy implementations to use this code.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'linux-can-next-for-4.8-20160623' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next

Marc Kleine-Budde says:

====================
pull-request: can-next 2016-06-17

this is a pull request of 4 patches for net-next/master.

Arnd Bergmann's patch fixes a regresseion in af_can introduced in
linux-can-next-for-4.8-20160617. There are two patches by Ramesh
Shanmugasundaram, which add CAN-2.0 support to the rcar_canfd driver.
And a patch by Ed Spiridonov that adds better error diagnoses messages
to the Ed Spiridonov driver.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace calls to kmalloc followed by a memcpy with a direct call to
kmemdup.

The Coccinelle semantic patch used to make this change is as follows:
@@
expression from,to,size,flag;
statement S;
@@

-  to = \(kmalloc\|kzalloc\)(size,flag);
+  to = kmemdup(from,size,flag);
   if (to==NULL || ...) S
-  memcpy(to, from, size);
Signed-off-by: NAmitoj Kaur Chawla <amitoj1606@gmail.com>
Acked-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

trivial fixes to spelling mistakes of the words "excessive collisions"
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

trivial fixes to spelling mistakes of the word "descriptors"
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox 100G mlx5e Ethernet extensions

This series includes multiple features extensions for mlx5 Ethernet netdevice driver.
Namely, TX Rate limiting, RX interrupt moderation, ethtool settings.

TX Rate limiting:
	- ConnectX-4 rate limiting infrastructure
	- Set max rate NDO support

RX interrupt moderation:
	- CQE based coalescing option (controlled via priv flags)
	- Adaptive RX coalescing

ethtool settings:
	- priv flags callbacks
	- Support new ksettings API
	- Add 50G missing link mode
	- Support auto negotiation on/off

Applied on top: 0e9390eb ("Merge branch 'mlxsw-next'")
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previous to this patch auto negotiation was reported off although it was
on by default in hardware. This patch reports the correct information to
ethtool and allows the user to toggle it on/off.

Added another parameter to set port proto function in order to pass
the auto negotiation field to the hardware.
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use new get/set link ksettings and remove get/set settings legacy
callbacks.
This allows us to use bitmasks longer than 32 bit for supported and
advertised link modes and use modes that were previously not supported.
Signed-off-by: NGal Pressman <galp@mellanox.com>
CC: Ben Hutchings <bwh@kernel.org>
CC: David Decotigny <decot@googlers.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add MLX5E_50GBASE_SR2 as ETHTOOL_LINK_MODE_50000baseSR2_Full_BIT.
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Cc: Ben Hutchings <bwh@kernel.org>
Cc: David Decotigny <decot@googlers.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ETHTOOL_LINK_MODE_50000baseSR2_Full_BIT bit.
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Cc: Ben Hutchings <bwh@kernel.org>
Cc: David Decotigny <decot@googlers.com>
Acked-By: NDavid Decotigny <decot@googlers.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a dedicated function to toggle port link. It should be called only
after setting a port register.
Toggle will set port link to down and bring it back up in case that it's
admin status was up.
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Striving for high message rate and low interrupt rate.

Usage:
        ethtool -C <interface> adaptive-rx on/off
Signed-off-by: NGil Rockah <gilr@mellanox.com>
Signed-off-by: NAchiad Shochat <achiad@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
CC: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In this mode the moderation timer will restart upon
new completion (CQE) generation rather than upon interrupt
generation.

The outcome is that for bursty traffic the period timer will never
expire and thus only the moderation frames counter will dictate
interrupt generation, thus the interrupt rate will be relative
to the incoming packets size.
If the burst seizes for "moderation period" time then an interrupt
will be issued immediately.

CQE based moderation is off by default and can be controlled
via ethtool set_priv_flags.

Performance tested on ConnectX4-Lx 50G.

Less packet loss in netperf UDP and TCP tests, with no bw degradation,
for both single and multi streams, with message sizes of
64, 1024, 1472 and 32768 byte.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NAchiad Shochat <achiad@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NGil Rockah <gilr@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce an infrastructure for getting/setting private net device
flags.

Currently a 'nop' priv flag is added, following patches will override
the flag will actual feature specific flags.
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement set_maxrate ndo.
Use the rate index from the hardware table to attach to channel SQ/TXQ.
In case of failure to configure new rate, the queue remains with
unlimited rate.

We save the configuration on priv structure and apply it each time
Send Queues are being reinitialized (after open/close) operations.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Configuring and managing HW rate limit tables.
The HW holds a table of rate limits, each rate is
associated with an index in that table.
Later a Send Queue uses this index to set the rate limit.
Multiple Send Queues can have the same rate limit, which is
represented by a single entry in this table.
Even though a rate can be shared, each queue is being rate
limited independently of others.

The SW shadow of this table holds the rate itself,
the index in the HW table and the refcount (number of queues)
working with this rate.

The exported functions are mlx5_rl_add_rate and mlx5_rl_remove_rate.
Number of different rates and their values are derived
from HW capabilities.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sathya Perla says:

====================
be2net: patch set

Hi Dave, pls consider commiting the following patches to the net-next tree.
Thanks!

Patch 1 replaces the be_max_eqs() macro with two new macros called
be_max_nic_eqs() and be_max_func_eqs() to clear confusion in that part
of the code.

Patch 2 adds support to configure asymmetric number of rx/tx queues via
ethtool set-channels option.

Patch 3 disables EVB when VFs are not enabled on a BE3 SR-IOV config to
avoid the broadcast echo problem.

Patch 4 updates copyright markings in be2net src files

Patch 5 updates the be2net maintainers' list
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes Padmanabh's name from the maintainers list as he's no
longer with the company. It also adds the driver name on the headline to
make it easy to lookup the maintainers list by the driver name.
Signed-off-by: NSathya Perla <sathya.perla@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates year and company name in the copyright markings in the
be2net source files.
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On SR-IOV profiles, when the user connects a Linux Bridge or OVS to a BE3
vport, they suffer the "broadcast/multicast echo" problem. BE3 EVB echoes
broadcast and multicast packets back to PF's vport confusing the
Linux bridge.  BE3 relies on the src-mac addr being programmed on the
interface to avoid sending back an echo of a broadcast or multicast packet
on a vPort. When a Linux bridge is connected to a BE3, the mac-addr of the
VM behind the bridge doesn't get configured on the vPort and so echo
cancellation doesn't work.
This patch worksaround this problem by disabling the EVB initially
and re-enabling it *only* when SR-IOV is enabled by the user. For the
driver fix to work, the BE3 FW version must be >= 11.1.84.0.
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

be2net so far supported creation of RX/TX queues only in pairs.
On configs where rx and tx queue counts are different, creation of only
the lesser number of queues has been supported.

This patch now allows a combination of RX/TX-only channels along with
combined channels. N TX-queues and M RX-queues can be created with the
following cmds:
ethtool -L ethX combined N rx M-N  (when N < M)
ethtool -L ethX combined M tx N-M (when M < N)

Setting both RX-only and TX-only channels is still not supported.
It is mandatory to create atleast one combined channel.
Signed-off-by: NSathya Perla <sathya.perla@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The EQs available on a function are shared between NIC and RoCE.
The be_max_eqs() macro was so far being used to refer to the max number of
EQs available for NIC. This has caused some confusion in the code. To fix
this confusion this patch introduces a new macro called be_max_nic_eqs()
to refer to the max number of EQs avialable for NIC only and renames
be_max_eqs() to be_max_func_eqs().
Signed-off-by: NSathya Perla <sathya.perla@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Andy Duan says:

====================
net: fec: add new type device

Different i.MX SOC FEC support different features like :
    - i.MX6Q/DL FEC does not support AVB and interrupt coalesc
    - i.MX6SX/i.MX7D supports AVB and interrupt coalesc
    - i.MX6UL/ULL does not support AVB, but support interrupt coalesc

Then, add new quirk flag to judge the supported features, and add new
type device for i.MX6UL.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

i.MX6UL is a member in i.MX series family, the SOC FEC inherits from
i.MX6SX but removes some IP features, lets define a new type for fec
device.
Signed-off-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Different i.MX SOC FEC support different features like :
- i.MX6Q/DL FEC does not support AVB and interrupt coalesc
- i.MX6SX/i.MX7D supports AVB and interrupt coalesc
- i.MX6UL/ULL does not support AVB, but support interrupt coalesc

So, add new quirk flag to judge the supported features.
Signed-off-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'rxrpc-rewrite-20160622-2' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs

David Howells says:

====================
rxrpc: Get rid of conn bundle and transport structs

Here's the next part of the AF_RXRPC rewrite.  The primary purpose of this
set is to get rid of the rxrpc_conn_bundle and rxrpc_transport structs.
This simplifies things for future development of the connection handling.

To this end, the following significant changes are made:

 (1) The rxrpc_connection struct is given pointers to the local and peer
     endpoints, inside the rxrpc_conn_parameters struct.  Pointers to the
     transport's copy of these pointers are then redirected to the
     connection struct.

 (2) Exclusive connection handling is fixed.  Exclusive connections should
     do just one call and then be retired.  They are used in security
     negotiations and, I believe, the idea is to avoid reuse of negotiated
     security contexts.

     The current code is doing a single connection per socket and doing all
     the calls over that.  With this change it gets a new connection for
     each call made.

 (3) A new sendmsg() control message marker is added to make individual
     calls operate over exclusive connections.  This should be used in
     future in preference to the sockopt that marks a socket as "exclusive
     connection".

 (4) IDs for client connections initiated by a machine are now allocated
     from a global pool using the IDR facility and are unique across all
     client connections, no matter their destination.  The IDR facility is
     then used to look up a connection on the connection ID alone.  Other
     parameters are then verified afterwards.

     Note that the IDR facility may use a lot of memory if the IDs it holds
     are widely scattered.  Given this, in a future commit, client
     connections will be retired if they are more than a certain distance
     from the last ID allocated.

     The client epoch is advanced by 1 each time the client ID counter
     wraps.  Connections outside the current epoch will also be retired in
     a future commit.

 (5) The connection bundle concept is removed and the client connection
     tree is moved into the local endpoint.  The queue for waiting for a
     call channel is moved to the rxrpc_connection struct as there can only
     be one connection for any particular key going to any particular peer
     now.

 (6) The rxrpc_transport struct is removed and the service connection tree
     is moved into the peer struct.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add constants and callback functions for the dwmac on rk3228/rk3229 socs.
As can be seen, the base structure is the same, only registers and the
bits in them moved slightly.
Signed-off-by: NXing Zheng <zhengxing@rock-chips.com>
Reviewed-by: NHeiko Stuebner <heiko@sntech.de>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>