DC9 has a separate HW flow from the rest of the DC states and it is
available in GEN9 LP platforms and on GEN11 and newer, so here
moving the assignment of the mask to a single conditional block to
simplifly code.

Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201111162408.98002-1-jose.souza@intel.com

!HAS_DISPLAY() implies !HAS_OVERLAY(), skipping overlay setup anyway, so
return earlier from intel_modeset_init() for clarity.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201106225531.920641-4-lucas.demarchi@intel.com

Display is always disabled and enabled when resetting any engine, but if
there is no display it should not do anything with display and only
reset the needed engines.

Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201106225531.920641-3-lucas.demarchi@intel.com

Rename intel_finish_reset to intel_display_finish_reset, so it's clear
from gt/ that we are calling out the display code.
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201106225531.920641-2-lucas.demarchi@intel.com

Rename intel_prepare_reset to intel_display_prepare_reset, so it's clear
from gt/ that we are calling out the display code.
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201106225531.920641-1-lucas.demarchi@intel.com

Reduce this maintenance nightmare a bit by converting the plane
min/max width/height stuff into vfuncs.

Now, if I could just think of a nice way to also use this for
intel_mode_valid_max_plane_size()...
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200924185113.30849-1-ville.syrjala@linux.intel.comReviewed-by: NAditya Swarup <aditya.swarup@intel.com>

JSL has update in vswing table for eDP.

BSpec: 21257

Changes since V1:
        - Fixed few checkpatch errors

Cc: Souza Jose <jose.souza@intel.com>
Signed-off-by: NTejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201020053657.99890-1-tejaskumarx.surendrakumar.upadhyay@intel.com

DG1 uses 2 registers for the ddi clock mapping, with PHY A and B using
DPCLKA_CFGCR0 and PHY C and D using DPCLKA1_CFGCR0. Hide this behind a
single macro that chooses the correct register according to the phy
being accessed, use the correct bitfields for each pll/phy and implement
separate functions for DG1 since it doesn't share much with ICL/TGL
anymore.

The previous values were correct for PHY A and B since they were using
the same register as before and the bitfields were matching.

v2: Add comment and try to simplify DG1_DPCLKA* macros by reusing
previous ones
v3:
  - Fix DG1_DPCLKA_CFGCR0_DDI_CLK_SEL_MASK() after wrong macro reuse
  - Move phy -> id map to a separate macro (Aditya)
  - Remove DG1_DPCLKA_CFGCR0_DDI_CLK_SEL_MASK where not required
    (Aditya)
  - Use drm_WARN_ON

Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Clinton Taylor <Clinton.A.Taylor@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NAditya Swarup <aditya.swarup@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201106210006.837953-1-lucas.demarchi@intel.com

To help diagnose modifier related issues let's include that
information in the various state dumps.

Cc: Simon Ser <contact@emersion.fr>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201103153026.16566-1-ville.syrjala@linux.intel.comAcked-by: NSimon Ser <contact@emersion.fr>

As per W/A implemented for TGL to program half of the nominal
DCO divider fraction value which is also applicable on EHL.

Changes since V2:
	- Apply stepping B0 till FOREVER
	- B0 - revid update as per Bspec 29153
Changes since V1:
        - ehl_ used as to keep earliest platform prefix
        - WA required B0 stepping onwards

Cc: Deak Imre <imre.deak@intel.com>
Signed-off-by: NTejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201104050655.171185-1-tejaskumarx.surendrakumar.upadhyay@intel.com

Replace the previous approach to force compute the initial PSR state
after i915 take over from firmware by the better and recently added
initial_fastset_check() hook.

Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201102221048.104294-1-jose.souza@intel.com

Fix a typo that led to some MST short pulse event handling issue (the
short pulse event was handled for both encoder instances, each having
its own state).

Fixes: 1d8ca002 ("drm/i915: Add PORT_TCn aliases to enum port")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201104010000.4165574-1-imre.deak@intel.com

If the VBT assigned tc->legacy_port mismatches the live_status indicator
for the connector, we ignore the VBT directive and switch over to the HW
setting. This is not a driver error, unless we happen to misparse the
VBT or the live_status registers. However, for the system in CI where
the error is only reported on 1 port out of 4, the evidence indicates
the VBT is wrong. Stop flaging this as an error since the cause is
beyond our control, fixup the mistake and continue on.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201030153209.14808-1-chris@chris-wilson.co.uk

As with the VBT DVO port, RKL uses PHY based mapping for the
VBT AUX CH. Adjust the code to use the new AUX_USBCn names
and add a comment to explain the situation.
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201028213323.5423-7-ville.syrjala@linux.intel.com

Let's make the AUX CH names match the spec (AUX A-F for pre-tgl,
AUX A-C or AUX USBC1-6 for tgl+). And while at it let's include
the full encoder name in the AUX CH name as well (as opposed to
just using port_name() which wouldn't give us the right thing on
tgl+).
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201028213323.5423-6-ville.syrjala@linux.intel.com

Just like with the DDIs tgl+ renamed the AUX CHs to reflect
the type of the DDI. Let's add the aliasing enum values for
the type-C AUX CHs.
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201028213323.5423-5-ville.syrjala@linux.intel.com

Let's pimp the DDI encoder->name to reflect what the spec calls them.
Ie. on pre-tgl DDI A-F, on tgl+ DDI A-C or DDI TC1-6.

Also since each encoder is really a combination of the DDI and the PHY
we include the PHY name as well.

ICL is a bit special since it already has the two different types
of DDIs (combo or TC) but it still calls them just DDI A-F regarless
of the type. For that let's add an extra "(TC)" note to remind
is which type of DDI it really is.

The code is darn ugly, but not sure there's much we can do about it.
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201028213323.5423-4-ville.syrjala@linux.intel.com

Since tgl the DDIs have been named A,B,C,TC1,TC2,TC3...
Add the appropriate enum values for the TC DDIs to enum port.

v2: Deal with rkl and dg1
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201028213323.5423-3-ville.syrjala@linux.intel.com

Make the namespacing for enum tc_port better by adding
the TC_ to the actual enum values.

v2: Drop the extra TC (Lucas)
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201028213323.5423-2-ville.syrjala@linux.intel.com

We don't currently handle the initial fb readout correctly
for 90/270 degree rotated scanout. Reject it.

Cc: stable@vger.kernel.org
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201020194330.28568-1-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit a40a8305)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

The atomic check hooks must look up the encoder to be used with a
connector from the connector's atomic state, and not assume that it's
the connector's current attached encoder. The latter one can change
under the atomic check func, or can be unset yet as in the case of MST
connectors.

This fixes
[    7.940719] Oops: 0000 [#1] SMP NOPTI
[    7.944407] CPU: 2 PID: 143 Comm: kworker/2:2 Not tainted 5.6.0-1023-oem #23-Ubuntu
[    7.952102] Hardware name: Dell Inc. Latitude 7320/, BIOS 88.87.11 09/07/2020
[    7.959278] Workqueue: events output_poll_execute [drm_kms_helper]
[    7.965511] RIP: 0010:intel_psr_atomic_check+0x37/0xa0 [i915]
[    7.971327] Code: 80 2d 06 00 00 20 74 42 80 b8 34 71 00 00 00 74 39 48 8b 72 08 48 85 f6 74 30 80 b8 f8 71 00 00 00 74 27 4c 8b 87 80 04 00 00 <41> 8b 78 78 83 ff 08 77 19 31 c9 83 ff 05 77 19 48 81 c1 20 01 00
[    7.977541] input: PS/2 Generic Mouse as /devices/platform/i8042/serio1/input/input5
[    7.990154] RSP: 0018:ffffb864c073fac8 EFLAGS: 00010202
[    7.990155] RAX: ffff8c5d55ce0000 RBX: ffff8c5d54519000 RCX: 0000000000000000
[    7.990155] RDX: ffff8c5d55cb30c0 RSI: ffff8c5d89a0c800 RDI: ffff8c5d55fcf800
[    7.990156] RBP: ffffb864c073fac8 R08: 0000000000000000 R09: ffff8c5d55d9f3a0
[    7.990156] R10: ffff8c5d55cb30c0 R11: 0000000000000009 R12: ffff8c5d55fcf800
[    7.990156] R13: ffff8c5d55cb30c0 R14: ffff8c5d56989cc0 R15: ffff8c5d56989cc0
[    7.990158] FS:  0000000000000000(0000) GS:ffff8c5d8e480000(0000) knlGS:0000000000000000
[    8.047193] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[    8.052970] CR2: 0000000000000078 CR3: 0000000856500005 CR4: 0000000000760ee0
[    8.060137] PKRU: 55555554
[    8.062867] Call Trace:
[    8.065361]  intel_digital_connector_atomic_check+0x53/0x130 [i915]
[    8.071703]  intel_dp_mst_atomic_check+0x5b/0x200 [i915]
[    8.077074]  drm_atomic_helper_check_modeset+0x1db/0x790 [drm_kms_helper]
[    8.083942]  intel_atomic_check+0x92/0xc50 [i915]
[    8.088705]  ? drm_plane_check_pixel_format+0x4f/0xb0 [drm]
[    8.094345]  ? drm_atomic_plane_check+0x7a/0x3a0 [drm]
[    8.099548]  drm_atomic_check_only+0x2b1/0x450 [drm]
[    8.104573]  drm_atomic_commit+0x18/0x50 [drm]
[    8.109070]  drm_client_modeset_commit_atomic+0x1c9/0x200 [drm]
[    8.115056]  drm_client_modeset_commit_force+0x55/0x160 [drm]
[    8.120866]  drm_fb_helper_restore_fbdev_mode_unlocked+0x54/0xb0 [drm_kms_helper]
[    8.128415]  drm_fb_helper_set_par+0x34/0x50 [drm_kms_helper]
[    8.134225]  drm_fb_helper_hotplug_event.part.0+0xb4/0xe0 [drm_kms_helper]
[    8.141150]  drm_fb_helper_hotplug_event+0x1c/0x30 [drm_kms_helper]
[    8.147481]  intel_fbdev_output_poll_changed+0x6f/0xa0 [i915]
[    8.153287]  drm_kms_helper_hotplug_event+0x2c/0x40 [drm_kms_helper]
[    8.159709]  output_poll_execute+0x1aa/0x1c0 [drm_kms_helper]
[    8.165506]  process_one_work+0x1e8/0x3b0
[    8.169561]  worker_thread+0x4d/0x400
[    8.173249]  kthread+0x104/0x140
[    8.176515]  ? process_one_work+0x3b0/0x3b0
[    8.180726]  ? kthread_park+0x90/0x90
[    8.184416]  ret_from_fork+0x1f/0x40

Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2361
References: https://gitlab.freedesktop.org/drm/intel/-/issues/2486Reported-by: NWilliam Tseng <william.tseng@intel.com>
Reported-by: NCooper Chiou <cooper.chiou@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NAnshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201027160928.3665377-1-imre.deak@intel.com

First check in the function is if swsci() is supported. All the error
paths are easy to figure out the reason, so remove the extra debug
message: it's normal not to support swsci() e.g. in dgfx.

v2: Rather than special case dgfx, just remove the debug message
    (from Ville)
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201027044618.719064-2-lucas.demarchi@intel.com

DG1 has one more combo phy port, no TC and all irq handling goes through
SDE, like for MCC.

v2: Also change intel_hpd_pin_default() to include DG1 mapping
v3, v4: Rebase on hpd refactor

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201021082034.3170478-2-lucas.demarchi@intel.com

Writes to CURSURFLIVE in TGL are causing IOMMU errors and visual
glitches that are often reproduced when executing CPU intensive
workloads while a eDP 4K panel is attached.

Manually exiting PSR causes the frontbuffer to be updated without
glitches and the IOMMU errors are also gone but this comes at the cost
of less time with PSR active.

So using this workaround until this issue is root caused and a better
fix is found.

The current code is already ready to enable PSR after this exit if
there is not other frontbuffer modifications.

Adding a new if block in psr_force_hw_tracking_exit() instead of reuse
the else/gen8- block because the plan is to revert this workaround
as soon as a better solution is found.

Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Tested-by: NGwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: NGwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201002231627.24528-1-jose.souza@intel.com

The block comment for cnl_program_nearest_filter_coefs() has a wonderful
diagram, but although it is marked up as kerneldoc does not use the
markup for providing the function definition.

drivers/gpu/drm/i915/display/intel_display.c:6341: warning: Function parameter or member 'dev_priv' not described in 'cnl_program_nearest_filter_coefs'
drivers/gpu/drm/i915/display/intel_display.c:6341: warning: Function parameter or member 'pipe' not described in 'cnl_program_nearest_filter_coefs'
drivers/gpu/drm/i915/display/intel_display.c:6341: warning: Function parameter or member 'id' not described in 'cnl_program_nearest_filter_coefs'
drivers/gpu/drm/i915/display/intel_display.c:6341: warning: Function parameter or member 'set' not described in 'cnl_program_nearest_filter_coefs'
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201021185649.17759-1-chris@chris-wilson.co.uk

We don't currently handle the initial fb readout correctly
for 90/270 degree rotated scanout. Reject it.

Cc: stable@vger.kernel.org
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201020194330.28568-1-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

GEN >= 10 hardware supports the programmable scaler filter.

Attach scaling filter property for CRTC and plane for GEN >= 10
hardwares and program scaler filter based on the selected filter
type.

changes since v3:
* None
changes since v2:
* Use updated functions
* Add ps_ctrl var to contain the full PS_CTRL register value (Ville)
* Duplicate the scaling filter in crtc and plane hw state (Ville)
changes since v1:
* None
Changes since RFC:
* Enable properties for GEN >= 10 platforms (Ville)
* Do not round off the crtc co-ordinate (Danial Stone, Ville)
* Add new functions to handle scaling filter setup (Ville)
* Remove coefficient set 0 hardcoding.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NUma Shankar <uma.shankar@intel.com>
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NAnkit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: NPankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201020161427.6941-5-pankaj.laxminarayan.bharadiya@intel.com

Integer scaling (IS) is a nearest-neighbor upscaling technique that
simply scales up the existing pixels by an integer
(i.e., whole number) multiplier.Nearest-neighbor (NN) interpolation
works by filling in the missing color values in the upscaled image
with that of the coordinate-mapped nearest source pixel value.

Both IS and NN preserve the clarity of the original image. Integer
scaling is particularly useful for pixel art games that rely on
sharp, blocky images to deliver their distinctive look.

Introduce functions to configure the scaler filter coefficients to
enable nearest-neighbor filtering.

Bspec: 49247

changes since v6:
* Trust compiler, remove pointless inline keyword from cnl_coef_tap()
  & cnl_nearest_filter_coef() functions (Ville)
changes since v4:
* Make cnl_coef_tap(), cnl_nearest_filter_coef() inline (Uma)
changes since v3:
* None
changes since v2:
* Move APIs from 5/5 into this patch.
* Change filter programming related function names to cnl_*, move
  filter select bits related code into inline function (Ville)
changes since v1:
* Rearrange skl_scaler_setup_nearest_neighbor_filter() to iterate the
  registers directly instead of the phases and taps (Ville)

changes since RFC:
* Refine the skl_scaler_setup_nearest_neighbor_filter() logic (Ville)
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NUma Shankar <uma.shankar@intel.com>
Signed-off-by: NShashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NAnkit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: NPankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201020161427.6941-4-pankaj.laxminarayan.bharadiya@intel.com

No functional changes in this patch.

With Bigjoiner, there are 2 pipes driving 2 halfs of 1
transcoder. The transcoder_mode has the full timings, and is used
for configuring the transcoder with the intended mode after
joining the 2 halves.
To clear the confusion, we rename intel_set_pipe_timings to
intel_set_transcoder_timings

v2:
* Split the renaming into separate patch (Ville)

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NManasi Navare <manasi.d.navare@intel.com>
Reviewed-by: NAnimesh Manna <animesh.manna@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201008214535.22942-2-manasi.d.navare@intel.com

Add a small wrapper for .hpd_irq_setup() which does the
"do we even have the hook?" and "are display interrupts enabled?"
checks.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201006185809.4655-3-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Currently we call .hpd_irq_setup() directly just before display
resume, and follow it with another call via intel_hpd_init()
just afterwards. Assuming the hpd pins are marked as enabled
during the open-coded call these two things do exactly the
same thing (ie. enable HPD interrupts). Which even makes sense
since we definitely need working HPD interrupts for MST sideband
during the display resume.

So let's nuke the open-coded call and move the intel_hpd_init()
call earlier. However we need to leave the poll_init_work stuff
behind after the display resume as that will trigger display
detection while we're resuming. We don't want that trampling over
the display resume process. To make this a bit more symmetric
we turn this into a intel_hpd_poll_{enable,disable}() pair.
So we end up with the following transformation:
intel_hpd_poll_init() -> intel_hpd_poll_enable()
lone intel_hpd_init() -> intel_hpd_init()+intel_hpd_poll_disable()
.hpd_irq_setup()+resume+intel_hpd_init() -> intel_hpd_init()+resume+intel_hpd_poll_disable()

If we really would like to prevent all *long* HPD processing during
display resume we'd need some kind of software mechanism to simply
ignore all long HPDs. Currently we appear to have that just for
fbdev via ifbdev->hpd_suspended. Since we aren't exploding left and
right all the time I guess that's mostly sufficient.

For a bit of history on this, we first got a mechanism to block
hotplug processing during suspend in commit 15239099 ("drm/i915:
enable irqs earlier when resuming") on account of moving the irq enable
earlier. This then got removed in commit 50c3dc97 ("drm/fb-helper:
Fix hpd vs. initial config races") because the fdev initial config
got pushed to a later point. The second ad-hoc hpd_irq_setup() for
resume was added in commit 0e32b39c ("drm/i915: add DP 1.2 MST
support (v0.7)") to be able to do MST sideband during the resume.
And finally we got a partial resurrection of the hpd blocking
mechanism in commit e8a8fedd ("drm/i915: Block fbdev HPD
processing during suspend"), but this time it only prevent fbdev
from handling hpd while resuming.

v2: Leave the poll_init_work behind
v3: Remove the extra intel_hpd_poll_disable() from display reset (Lyude)
    Add the missing intel_hpd_poll_disable() to display init (Imre)

Cc: Lyude Paul <lyude@redhat.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201013181137.30560-1-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NLyude Paul <lyude@redhat.com>

Rename intel_dp_sink_dpms() to intel_dp_set_power()
so one doesn't always have to convert from the DPMS
enum values to the actual DP D-states.

Also when dealing with a branch device this has nothing to
do with any sink, so the old name was nonsense anyway.
Also adjust the debug message accordingly, and pimp it
with the standard encoder id+name thing.

Trivial bits done with cocci:
@@
expression DP;
@@
(
- intel_dp_sink_dpms(DP, DRM_MODE_DPMS_OFF)
+ intel_dp_set_power(DP, DP_SET_POWER_D3)
|
- intel_dp_sink_dpms(DP, DRM_MODE_DPMS_ON)
+ intel_dp_set_power(DP, DP_SET_POWER_D0)
)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201016194800.25581-2-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Rather that try to trick LSPCON back into PCON mode from the .reset()
hook let's just do that as a regular part of the normal modeset
sequence, which is going to take care of the system resume case. During
a normal modeset this should normally be a nop as the mode should have
already been switched by .detect().
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201016194800.25581-1-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Underruns happens when plane height + y offset is not a modulo of 4
when FBC is enabled. It happens when scanline is at vactive - 10 but
that is not feasible to do from the software side so here completely
disabling FBC when height + y offset matches to avoid visual glitches.

Specification says that it only affects TGL display C stepping and
newer but to simply the check and as TGL is already in final costumers
hands, pre-production display stepping A and B was also included.

BSpec: 52887 ICL
BSpec: 52888 EHL/JSL
BSpec: 52890/55378 TGL
BSpec: 53508 DG1
BSpec: 53273 RKL
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201019175609.28715-1-jose.souza@intel.com

This sequence is not part of "Sequences to Initialize Display" but
as noted in the MBus page the DBUF_CTL.Tracker_state_service needs
to be set to 8.

BSpec: 49213
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201019173906.18892-1-jose.souza@intel.com

Currently we leave the cache_level of the initial fb obj
set to NONE. This means on eLLC machines the first pin_to_display()
will try to switch it to WT which requires a vma unbind+bind.
If that happens during the fbdev initialization rcu does not
seem operational which causes the unbind to get stuck. To
most appearances this looks like a dead machine on boot.

Avoid the unbind by already marking the object cache_level
as WT when creating it. We still do an excplicit ggtt pin
which will rewrite the PTEs anyway, so they will match whatever
cache level we set.

Cc: <stable@vger.kernel.org> # v5.7+
Suggested-by: NChris Wilson <chris@chris-wilson.co.uk>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2381Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007120329.17076-1-ville.syrjala@linux.intel.com
Link: https://patchwork.freedesktop.org/patch/msgid/20201015122138.30161-1-chris@chris-wilson.co.uk
(cherry picked from commit d46b60a2)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

In commit 79946723 ("drm/i915: Assume 100% brightness when not in
DPCD control mode"), we fixed the brightness level when DPCD control was
not active to max brightness. This is as good as we can guess since most
backlights go on full when uncontrolled.

However in doing so we changed the semantics of the initial
'backlight.enabled' value. At least on Pixelbooks, they  were relying
on the brightness level in DP_EDP_BACKLIGHT_BRIGHTNESS_MSB to be 0 on
boot such that enabled would be false. This causes the device to be
enabled when the brightness is set. Without this, brightness control
doesn't work. So by changing brightness to max, we also flipped enabled
to be true on boot.

To fix this, make enabled a function of brightness and backlight control
mechanism.

Fixes: 79946723 ("drm/i915: Assume 100% brightness when not in DPCD control mode")
Cc: Lyude Paul <lyude@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Kevin Chowski <chowski@chromium.org>>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Reviewed-by: NLyude Paul <lyude@redhat.com>
Signed-off-by: NLyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200918002845.32766-1-sean@poorly.run
(cherry picked from commit 4ade8f31)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

intel_dp_ycbcr420_config() is rather pointless. Just inline it
directly into intel_dp_compute_config(). This gets rid of the
ugly double assignment of output_format.

Not really sure what the best policy would be when the user
supplies a mode classified by the display as "YCbCr 4:2:0
only", but we know that we can't do YCbCr 4:2:0 output. For
now keep the current behaviour of just silently upgrade
it to RGB 4:4:4.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200924184156.24491-3-ville.syrjala@linux.intel.comReviewed-by: NUma Shankar <uma.shankar@intel.com>

Remove the lspcon special case from intel_dp_compute_config() and
just treat it like any other DFP than can do 4:4:4->4:2:0 conversion.

The only difference between the two codepaths was that the lspcon
code tried to already halve port_clock. That was just total nonsense
as we hadn't even computed the base port_clock at that time.
All that stuff happens intel_dp_compute_link_config*() and it
already takes care of the 4:2:0 clock reduction.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200924184156.24491-2-ville.syrjala@linux.intel.comReviewed-by: NUma Shankar <uma.shankar@intel.com>

crtc_state->lspcon_downsampling isn't particularly useful at
the moment since we can't even do proper readout for it.
Let's get rid of it. Will help with unifying the LSPCON with
the regular DFP YCbCr output support.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200924184156.24491-1-ville.syrjala@linux.intel.comReviewed-by: NUma Shankar <uma.shankar@intel.com>