When I have KASAN enabled on my kernel and I start stressing the
touchscreen my system tends to hang.  The touchscreen is one of the
only things that does a lot of big i2c transfers and ends up hitting
the DMA paths in the geni i2c driver.  It appears that KASAN adds
enough delay in my system to tickle a race condition in the DMA setup
code.

When the system hangs, I found that it was running the geni_i2c_irq()
over and over again.  It had these:

m_stat   = 0x04000080
rx_st    = 0x30000011
dm_tx_st = 0x00000000
dm_rx_st = 0x00000000
dma      = 0x00000001

Notably we're in DMA mode but are getting M_RX_IRQ_EN and
M_RX_FIFO_WATERMARK_EN over and over again.

Putting some traces in geni_i2c_rx_one_msg() showed that when we
failed we were getting to the start of geni_i2c_rx_one_msg() but were
never executing geni_se_rx_dma_prep().

I believe that the problem here is that we are starting the geni
command before we run geni_se_rx_dma_prep().  If a transfer makes it
far enough before we do that then we get into the state I have
observed.  Let's change the order, which seems to work fine.

Although problems were seen on the RX path, code inspection suggests
that the TX should be changed too.  Change it as well.

Fixes: 37692de5 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller")
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Tested-by: NSai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: NAkash Asthana <akashast@codeaurora.org>
Reviewed-by: NStephen Boyd <swboyd@chromium.org>
Reviewed-by: NMukesh Kumar Savaliya <msavaliy@codeaurora.org>
Signed-off-by: NWolfram Sang <wsa@kernel.org>

On R-Car Gen2, we get a timeout when reading from the address set in
ICSAR, even though the slave interface is disabled. Clearing it fixes
this situation. Note that Gen3 is not affected.

To reproduce: bind and undbind an I2C slave on some bus, run
'i2cdetect' on that bus.

Fixes: de20d185 ("i2c: rcar: add slave support")
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NWolfram Sang <wsa@kernel.org>

My colleague Codrin Ciubotariu, now, maintains this driver internally.
Then I handover the mainline maintenance to him.
Signed-off-by: NLudovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: NWolfram Sang <wsa@kernel.org>

Drop the doubled word "be" in a comment.
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NWolfram Sang <wsa@kernel.org>

There are few issues on Zynq SOC observed in the stress tests causing
timeout errors. Even though all the data is received, timeout error
is thrown. This is due to an IP bug in which the COMP bit in ISR is
not set at end of transfer and completion interrupt is not generated.

This bug is seen on Zynq platforms when the following condition occurs:
Master read & HOLD bit set & Transfer size register reaches '0'.

One workaround is to clear the HOLD bit before the transfer size
register reaches '0'. The current implementation checks for this at
the start of the loop and also only for less than FIFO DEPTH case
(ignoring the equal to case).

So clear the HOLD bit when the data yet to receive is less than or
equal to the FIFO DEPTH. This avoids the IP bug condition.
Signed-off-by: NRaviteja Narayanam <raviteja.narayanam@xilinx.com>
Acked-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NWolfram Sang <wsa@kernel.org>

This reverts commit d358def7.

There are two issues with "i2c: cadence: Fix the hold bit setting" commit.

1. In case of combined message request from user space, when the HOLD
bit is cleared in cdns_i2c_mrecv function, a STOP condition is sent
on the bus even before the last message is started. This is because when
the HOLD bit is cleared, the FIFOS are empty and there is no pending
transfer. The STOP condition should occur only after the last message
is completed.

2. The code added by the commit is redundant. Driver is handling the
setting/clearing of HOLD bit in right way before the commit.

The setting of HOLD bit based on 'bus_hold_flag' is taken care in
cdns_i2c_master_xfer function even before cdns_i2c_msend/cdns_i2c_recv
functions.

The clearing of HOLD bit is taken care at the end of cdns_i2c_msend and
cdns_i2c_recv functions based on bus_hold_flag and byte count.
Since clearing of HOLD bit is done after the slave address is written to
the register (writing to address register triggers the message transfer),
it is ensured that STOP condition occurs at the right time after
completion of the pending transfer (last message).
Signed-off-by: NRaviteja Narayanam <raviteja.narayanam@xilinx.com>
Acked-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NWolfram Sang <wsa@kernel.org>

Merge tag 'perf-tools-fixes-2020-07-19' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into master

Pull perf tooling fixes from Arnaldo Carvalho de Melo:

 - Update hashmap.h from libbpf and kvm.h from x86's kernel UAPI.

 - Set opt->set in libsubcmd's OPT_CALLBACK_SET(). This fixes
   'perf record --switch-output-event event-name' usage"

* tag 'perf-tools-fixes-2020-07-19' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
  tools arch kvm: Sync kvm headers with the kernel sources
  perf tools: Sync hashmap.h with libbpf's
  libsubcmd: Fix OPT_CALLBACK_SET()

Merge tag 'x86-urgent-2020-07-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into master

Pull x86 fixes from Thomas Gleixner:
 "A pile of fixes for x86:

   - Fix the I/O bitmap invalidation on XEN PV, which was overlooked in
     the recent ioperm/iopl rework. This caused the TSS and XEN's I/O
     bitmap to get out of sync.

   - Use the proper vectors for HYPERV.

   - Make disabling of stack protector for the entry code work with GCC
     builds which enable stack protector by default. Removing the option
     is not sufficient, it needs an explicit -fno-stack-protector to
     shut it off.

   - Mark check_user_regs() noinstr as it is called from noinstr code.
     The missing annotation causes it to be placed in the text section
     which makes it instrumentable.

   - Add the missing interrupt disable in exc_alignment_check()

   - Fixup a XEN_PV build dependency in the 32bit entry code

   - A few fixes to make the Clang integrated assembler happy

   - Move EFI stub build to the right place for out of tree builds

   - Make prepare_exit_to_usermode() static. It's not longer called from
     ASM code"

* tag 'x86-urgent-2020-07-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/boot: Don't add the EFI stub to targets
  x86/entry: Actually disable stack protector
  x86/ioperm: Fix io bitmap invalidation on Xen PV
  x86: math-emu: Fix up 'cmp' insn for clang ias
  x86/entry: Fix vectors to IDTENTRY_SYSVEC for CONFIG_HYPERV
  x86/entry: Add compatibility with IAS
  x86/entry/common: Make prepare_exit_to_usermode() static
  x86/entry: Mark check_user_regs() noinstr
  x86/traps: Disable interrupts in exc_aligment_check()
  x86/entry/32: Fix XEN_PV build dependency

Merge tag 'timers-urgent-2020-07-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into master

Pull timer fixes from Thomas Gleixner:
 "Two fixes for the timer wheel:

   - A timer which is already expired at enqueue time can set the
     base->next_expiry value backwards. As a consequence base->clk can
     be set back as well. This can lead to timers expiring early. Add a
     sanity check to prevent this.

   - When a timer is queued with an expiry time beyond the wheel
     capacity then it should be queued in the bucket of the last wheel
     level which is expiring last.

     The code adjusted the expiry time to the maximum wheel capacity,
     which is only correct when the wheel clock is 0. Aside of that the
     check whether the delta is larger than wheel capacity does not
     check the delta, it checks the expiry value itself. As a result
     timers can expire at random.

     Fix this by checking the right variable and adjust expiry time so
     it becomes base->clock plus capacity which places it into the
     outmost bucket in the last wheel level"

* tag 'timers-urgent-2020-07-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timer: Fix wheel index calculation on last level
  timer: Prevent base->clk from moving backward

Merge tag 'sched-urgent-2020-07-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into master

Pull scheduler fixes from Thomas Gleixner:
 "A set of scheduler fixes:

   - Plug a load average accounting race which was introduced with a
     recent optimization casing load average to show bogus numbers.

   - Fix the rseq CPU id initialization for new tasks. sched_fork() does
     not update the rseq CPU id so the id is the stale id of the parent
     task, which can cause user space data corruption.

   - Handle a 0 return value of task_h_load() correctly in the load
     balancer, which does not decrease imbalance and therefore pulls
     until the maximum number of loops is reached, which might be all
     tasks just created by a fork bomb"

* tag 'sched-urgent-2020-07-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/fair: handle case of task_h_load() returning 0
  sched: Fix unreliable rseq cpu_id for new tasks
  sched: Fix loadavg accounting race

Merge tag 'irq-urgent-2020-07-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into master

Pull irq fixes from Thomas Gleixner:
 "Two fixes for the interrupt subsystem:

   - Make the handling of the firmware node consistent and do not free
     the node after the domain has been created successfully. The core
     code stores a pointer to it which can lead to a use after free or
     double free.

     This used to "work" because the pointer was not stored when the
     initial code was written, but at some point later it was required
     to store it. Of course nobody noticed that the existing users break
     that way.

   - Handle affinity setting on inactive interrupts correctly when
     hierarchical irq domains are enabled.

     When interrupts are inactive with the modern hierarchical irqdomain
     design, the interrupt chips are not necessarily in a state where
     affinity changes can be handled. The legacy irq chip design allowed
     this because interrupts are immediately fully initialized at
     allocation time. X86 has a hacky workaround for this, but other
     implementations do not.

     This cased malfunction on GIC-V3. Instead of playing whack a mole
     to find all affected drivers, change the core code to store the
     requested affinity setting and then establish it when the interrupt
     is allocated, which makes the X86 hack go away"

* tag 'irq-urgent-2020-07-19' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq/affinity: Handle affinity setting on inactive interrupts correctly
  irqdomain/treewide: Keep firmware node unconditionally allocated

Pull USB fixes from Greg KH:
 "Here are a few small USB fixes, and one thunderbolt fix, for 5.8-rc6.

  Nothing huge in here, just the normal collection of gadget, dwc2/3,
  serial, and other minor USB driver fixes and id additions. Full
  details are in the shortlog.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'usb-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: serial: iuu_phoenix: fix memory corruption
  USB: c67x00: fix use after free in c67x00_giveback_urb
  usb: gadget: function: fix missing spinlock in f_uac1_legacy
  usb: gadget: udc: atmel: fix uninitialized read in debug printk
  usb: gadget: udc: atmel: remove outdated comment in usba_ep_disable()
  usb: dwc2: Fix shutdown callback in platform
  usb: cdns3: trace: fix some endian issues
  usb: cdns3: ep0: fix some endian issues
  usb: gadget: udc: gr_udc: fix memleak on error handling path in gr_ep_init()
  usb: gadget: fix langid kernel-doc warning in usbstring.c
  usb: dwc3: pci: add support for the Intel Jasper Lake
  usb: dwc3: pci: add support for the Intel Tiger Lake PCH -H variant
  usb: chipidea: core: add wakeup support for extcon
  USB: serial: option: add Quectel EG95 LTE modem
  thunderbolt: Fix path indices used in USB3 tunnel discovery
  USB: serial: ch341: add new Product ID for CH340
  USB: serial: option: add GosunCn GM500 series
  USB: serial: cypress_m8: enable Simply Automated UPB PIM

Pull dma-mapping fixes from Christoph Hellwig:
 "Ensure we always have fully addressable memory in the dma coherent
  pool (Nicolas Saenz Julienne)"

* tag 'dma-mapping-5.8-6' of git://git.infradead.org/users/hch/dma-mapping:
  dma-pool: do not allocate pool memory from CMA
  dma-pool: make sure atomic pool suits device
  dma-pool: introduce dma_guess_pool()
  dma-pool: get rid of dma_in_atomic_pool()
  dma-direct: provide function to check physical memory area validity

vmlinux-objs-y is added to targets, which currently means that the EFI
stub gets added to the targets as well. It shouldn't be added since it
is built elsewhere.

This confuses Makefile.build which interprets the EFI stub as a target
	$(obj)/$(objtree)/drivers/firmware/efi/libstub/lib.a
and will create drivers/firmware/efi/libstub/ underneath
arch/x86/boot/compressed, to hold this supposed target, if building
out-of-tree. [0]

Fix this by pulling the stub out of vmlinux-objs-y into efi-obj-y.

[0] See scripts/Makefile.build near the end:
    # Create directories for object files if they do not exist
Signed-off-by: NArvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NMasahiro Yamada <masahiroy@kernel.org>
Acked-by: NArd Biesheuvel <ardb@kernel.org>
Link: https://lkml.kernel.org/r/20200715032631.1562882-1-nivedita@alum.mit.edu

Some builds of GCC enable stack protector by default. Simply removing
the arguments is not sufficient to disable stack protector, as the stack
protector for those GCC builds must be explicitly disabled. Remove the
argument removals and add -fno-stack-protector. Additionally include
missed x32 argument updates, and adjust whitespace for readability.

Fixes: 20355e5f ("x86/entry: Exclude low level entry code from sanitizing")
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/202006261333.585319CA6B@keescook

Pull SCSI fix from James Bottomley:
 "One small driver fix. Although the one liner makes it sound like a
  cosmetic change, it's a regression fix for the megaraid_sas driver"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: megaraid_sas: Remove undefined ENABLE_IRQ_POLL macro

Merge tag 'hwmon-for-v5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging into master

Pull hwmon fixes from Guenter Roeck:

 - Using SCT on some Tohsiba drives causes firmware hangs. Disable its
   use in the drivetemp driver.

 - Handle potential buffer overflows in scmi and aspeed-pwm-tacho
   driver.

 - Energy reporting does not work well on all AMD CPUs. Restrict
   amd_energy to known working models.

 - Enable reading the CPU temperature on NCT6798D using undocumented
   registers.

 - Fix read errors seen if PEC is enabled in adm1275 driver.

 - Fix setting the pwm1_enable in emc2103 driver.

* tag 'hwmon-for-v5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (drivetemp) Avoid SCT usage on Toshiba DT01ACA family drives
  hwmon: (scmi) Fix potential buffer overflow in scmi_hwmon_probe()
  hwmon: (nct6775) Accept PECI Calibration as temperature source for NCT6798D
  hwmon: (adm1275) Make sure we are reading enough data for different chips
  hwmon: (emc2103) fix unable to change fan pwm1_enable attribute
  hwmon: (amd_energy) match for supported models
  hwmon: (aspeed-pwm-tacho) Avoid possible buffer overflow

Merge tag 'riscv-for-linus-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux into master

Pull RISC-V fixes from Palmer Dabbelt:
 "Two fixes:

   - 16KiB kernel stacks on rv64, which fixes a lot of crashes.

   - Rolling an mmiowb() into the scheduler, which when combined with
     Will's fix to the mmiowb()-on-spinlock should fix the PREEMPT
     issues we've been seeing"

* tag 'riscv-for-linus-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  RISC-V: Upgrade smp_mb__after_spinlock() to iorw,iorw
  riscv: use 16KB kernel stack on 64-bit

Merge tag 'powerpc-5.8-7' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux into master

Pull powerpc fixes from Michael Ellerman:
 "Some more powerpc fixes for 5.8:

   - A fix to the VAS code we merged this cycle, to report the proper
     error code to userspace for address translation failures. And a
     selftest update to match.

   - Another fix for our pkey handling of PROT_EXEC mappings.

   - A fix for a crash when booting a "secure VM" under an ultravisor
     with certain numbers of CPUs.

  Thanks to: Aneesh Kumar K.V, Haren Myneni, Laurent Dufour, Sandipan
  Das, Satheesh Rajendran, Thiago Jung Bauermann"

* tag 'powerpc-5.8-7' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  selftests/powerpc: Use proper error code to check fault address
  powerpc/vas: Report proper error code for address translation failure
  powerpc/pseries/svm: Fix incorrect check for shared_lppaca_size
  powerpc/book3s64/pkeys: Fix pkey_access_permitted() for execute disable pkey

It has been observed that Toshiba DT01ACA family drives have
WRITE FPDMA QUEUED command timeouts and sometimes just freeze until
power-cycled under heavy write loads when their temperature is getting
polled in SCT mode. The SMART mode seems to be fine, though.

Let's make sure we don't use SCT mode for these drives then.

While only the 3 TB model was actually caught exhibiting the problem let's
play safe here to avoid data corruption and extend the ban to the whole
family.

Fixes: 5b46903d ("hwmon: Driver for disk and solid state drives with temperature sensors")
Cc: stable@vger.kernel.org
Signed-off-by: NMaciej S. Szmigiero <mail@maciej.szmigiero.name>
Link: https://lore.kernel.org/r/0cb2e7022b66c6d21d3f189a12a97878d0e7511b.1595075458.git.mail@maciej.szmigiero.nameSigned-off-by: NGuenter Roeck <linux@roeck-us.net>

tss_invalidate_io_bitmap() wasn't wired up properly through the pvop
machinery, so the TSS and Xen's io bitmap would get out of sync
whenever disabling a valid io bitmap.

Add a new pvop for tss_invalidate_io_bitmap() to fix it.

This is XSA-329.

Fixes: 22fe5b04 ("x86/ioperm: Move TSS bitmap update to exit to user work")
Signed-off-by: NAndy Lutomirski <luto@kernel.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NJuergen Gross <jgross@suse.com>
Reviewed-by: NThomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/d53075590e1f91c19f8af705059d3ff99424c020.1595030016.git.luto@kernel.org

Pull NFS client fixes from Anna Schumaker:
 "A few more NFS client bugfixes for Linux 5.8:

  NFS:
   - Fix interrupted slots by using the SEQUENCE operation

  SUNRPC:
   - revert d03727b2 to fix unkillable IOs

  xprtrdma:
   - Fix double-free in rpcrdma_ep_create()
   - Fix recursion into rpcrdma_xprt_disconnect()
   - Fix return code from rpcrdma_xprt_connect()
   - Fix handling of connect errors
   - Fix incorrect header size calculations"

* tag 'nfs-for-5.8-3' of git://git.linux-nfs.org/projects/anna/linux-nfs:
  SUNRPC reverting d03727b2 ("NFSv4 fix CLOSE not waiting for direct IO compeletion")
  xprtrdma: fix incorrect header size calculations
  NFS: Fix interrupted slots by sending a solo SEQUENCE operation
  xprtrdma: Fix handling of connect errors
  xprtrdma: Fix return code from rpcrdma_xprt_connect()
  xprtrdma: Fix recursion into rpcrdma_xprt_disconnect()
  xprtrdma: Fix double-free in rpcrdma_ep_create()

Pull ARM SoC fixes from Arnd Bergmann:
 "This time there are a number of actual code fixes, plus a small set of
  device tree issues getting addressed:

  Renesas:

    - one defconfig cleanup to allow a later Kconfig change

  Intel socfpga:

    - enable QSPI devices on some machines

    - fix DTC validation warnings

  TI OMAP:

    - Two DEBUG_ATOMIC_SLEEP fixes for ti-sysc interconnect target
      module driver

    - A regression fix for ti-sysc no-idle handling that caused issues
      compared to earlier platform data based booting

    - A fix for memory leak for omap_hwmod_allocate_module

    - Fix d_can driver probe for am437x

  NXP i.MX:

    - A couple of fixes on i.MX platform device registration code to
      stop the use of invalid IRQ 0.

    - Fix a regression seen on ls1021a platform, caused by commit
      52102a3b ("soc: imx: move cpu code to drivers/soc/imx").

    - Fix a misconfiguration of audio SSI on imx6qdl-gw551x board.

  Amlogic Meson:

    - misc DT fixes

    - SoC ID fixes to detect all chips correctly"

* tag 'arm-fixes-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  arm64: dts: spcfpga: Align GIC, NAND and UART nodenames with dtschema
  ARM: dts: socfpga: Align L2 cache-controller nodename with dtschema
  arm64: dts: stratix10: increase QSPI reg address in nand dts file
  arm64: dts: stratix10: add status to qspi dts node
  arm64: dts: agilex: add status to qspi dts node
  ARM: dts: Fix dcan driver probe failed on am437x platform
  ARM: OMAP2+: Fix possible memory leak in omap_hwmod_allocate_module
  arm64: defconfig: Enable CONFIG_PCIE_RCAR_HOST
  soc: imx: check ls1021a
  ARM: imx: Remove imx_add_imx_dma() unused irq_err argument
  ARM: imx: Provide correct number of resources when registering gpio devices
  ARM: dts: imx6qdl-gw551x: fix audio SSI
  bus: ti-sysc: Do not disable on suspend for no-idle
  bus: ti-sysc: Fix sleeping function called from invalid context for RTC quirk
  bus: ti-sysc: Fix wakeirq sleeping function called from invalid context
  ARM: dts: meson: Align L2 cache-controller nodename with dtschema
  arm64: dts: meson-gxl-s805x: reduce initial Mali450 core frequency
  arm64: dts: meson: add missing gxl rng clock
  soc: amlogic: meson-gx-socinfo: Fix S905X3 and S905D3 ID's

Pull arm64 fixes from Will Deacon:
 "A batch of arm64 fixes.

  Although the diffstat is a bit larger than we'd usually have at this
  stage, a decent amount of it is the addition of comments describing
  our syscall tracing behaviour, and also a sweep across all the modular
  arm64 PMU drivers to make them rebust against unloading and unbinding.

  There are a couple of minor things kicking around at the moment (CPU
  errata and module PLTs for very large modules), but I'm not expecting
  any significant changes now for us in 5.8.

   - Fix kernel text addresses for relocatable images booting using EFI
     and with KASLR disabled so that they match the vmlinux ELF binary.

   - Fix unloading and unbinding of PMU driver modules.

   - Fix generic mmiowb() when writeX() is called from preemptible
     context (reported by the riscv folks).

   - Fix ptrace hardware single-step interactions with signal handlers,
     system calls and reverse debugging.

   - Fix reporting of 64-bit x0 register for 32-bit tasks via
     'perf_regs'.

   - Add comments describing syscall entry/exit tracing ABI"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  drivers/perf: Prevent forced unbinding of PMU drivers
  asm-generic/mmiowb: Allow mmiowb_set_pending() when preemptible()
  arm64: Use test_tsk_thread_flag() for checking TIF_SINGLESTEP
  arm64: ptrace: Use NO_SYSCALL instead of -1 in syscall_trace_enter()
  arm64: syscall: Expand the comment about ptrace and syscall(-1)
  arm64: ptrace: Add a comment describing our syscall entry/exit trap ABI
  arm64: compat: Ensure upper 32 bits of x0 are zero on syscall return
  arm64: ptrace: Override SPSR.SS when single-stepping is enabled
  arm64: ptrace: Consistently use pseudo-singlestep exceptions
  drivers/perf: Fix kernel panic when rmmod PMU modules during perf sampling
  efi/libstub/arm64: Retain 2MB kernel Image alignment if !KASLR

Setting interrupt affinity on inactive interrupts is inconsistent when
hierarchical irq domains are enabled. The core code should just store the
affinity and not call into the irq chip driver for inactive interrupts
because the chip drivers may not be in a state to handle such requests.

X86 has a hacky workaround for that but all other irq chips have not which
causes problems e.g. on GIC V3 ITS.

Instead of adding more ugly hacks all over the place, solve the problem in
the core code. If the affinity is set on an inactive interrupt then:

    - Store it in the irq descriptors affinity mask
    - Update the effective affinity to reflect that so user space has
      a consistent view
    - Don't call into the irq chip driver

This is the core equivalent of the X86 workaround and works correctly
because the affinity setting is established in the irq chip when the
interrupt is activated later on.

Note, that this is only effective when hierarchical irq domains are enabled
by the architecture. Doing it unconditionally would break legacy irq chip
implementations.

For hierarchial irq domains this works correctly as none of the drivers can
have a dependency on affinity setting in inactive state by design.

Remove the X86 workaround as it is not longer required.

Fixes: 02edee15 ("x86/apic/vector: Ignore set_affinity call for inactive interrupts")
Reported-by: NAli Saidi <alisaidi@amazon.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NAli Saidi <alisaidi@amazon.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200529015501.15771-1-alisaidi@amazon.com
Link: https://lkml.kernel.org/r/877dv2rv25.fsf@nanos.tec.linutronix.de

When an expiration delta falls into the last level of the wheel, that delta
has be compared against the maximum possible delay and reduced to fit in if
necessary.

However instead of comparing the delta against the maximum, the code
compares the actual expiry against the maximum. Then instead of fixing the
delta to fit in, it sets the maximum delta as the expiry value.

This can result in various undesired outcomes, the worst possible one
being a timer expiring 15 days ahead to fire immediately.

Fixes: 500462a9 ("timers: Switch to a non-cascading wheel")
Signed-off-by: NFrederic Weisbecker <frederic@kernel.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20200717140551.29076-2-frederic@kernel.org

Reverting commit d03727b2 "NFSv4 fix CLOSE not waiting for
direct IO compeletion". This patch made it so that fput() by calling
inode_dio_done() in nfs_file_release() would wait uninterruptably
for any outstanding directIO to the file (but that wait on IO should
be killable).

The problem the patch was also trying to address was REMOVE returning
ERR_ACCESS because the file is still opened, is supposed to be resolved
by server returning ERR_FILE_OPEN and not ERR_ACCESS.
Signed-off-by: NOlga Kornievskaia <kolga@netapp.com>
Signed-off-by: NAnna Schumaker <Anna.Schumaker@Netapp.com>

Pull io_uring fix from Jens Axboe:
 "Fix for a case where, with automatic buffer selection, we can leak the
  buffer descriptor for recvmsg"

* tag 'io_uring-5.8-2020-07-17' of git://git.kernel.dk/linux-block:
  io_uring: fix recvmsg memory leak with buffer selection

Pull block fix from Jens Axboe:
 "Single NVMe multipath capacity fix"

* tag 'block-5.8-2020-07-17' of git://git.kernel.dk/linux-block:
  nvme: explicitly update mpath disk capacity on revalidation

Merge tag 'fuse-fixes-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse into master

Pull fuse fixes from Miklos Szeredi:

 - two regressions in this cycle caused by the conversion of writepage
   list to an rb_tree

 - two regressions in v5.4 cause by the conversion to the new mount API

 - saner behavior of fsconfig(2) for the reconfigure case

 - an ancient issue with FS_IOC_{GET,SET}FLAGS ioctls

* tag 'fuse-fixes-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: Fix parameter for FS_IOC_{GET,SET}FLAGS
  fuse: don't ignore errors from fuse_writepages_fill()
  fuse: clean up condition for writepage sending
  fuse: reject options on reconfigure via fsconfig(2)
  fuse: ignore 'data' argument of mount(..., MS_REMOUNT)
  fuse: use ->reconfigure() instead of ->remount_fs()
  fuse: fix warning in tree_insert() and clean up writepage insertion
  fuse: move rb_erase() before tree_insert()

Merge tag 'ovl-fixes-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs into master

Pull overlayfs fixes from Miklos Szeredi:

 - fix a regression introduced in v4.20 in handling a regenerated
   squashfs lower layer

 - two regression fixes for this cycle, one of which is Oops inducing

 - miscellaneous issues

* tag 'ovl-fixes-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
  ovl: fix lookup of indexed hardlinks with metacopy
  ovl: fix unneeded call to ovl_change_flags()
  ovl: fix mount option checks for nfs_export with no upperdir
  ovl: force read-only sb on failure to create index dir
  ovl: fix regression with re-formatted lower squashfs
  ovl: fix oops in ovl_indexdir_cleanup() with nfs_export=on
  ovl: relax WARN_ON() when decoding lower directory file handle
  ovl: remove not used argument in ovl_check_origin
  ovl: change ovl_copy_up_flags static
  ovl: inode reference leak in ovl_is_inuse true case.

Merge tag 'spi-fix-v5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi into master

Pull spi fixes from Mark Brown:
 "A couple of small driver specific fixes for fairly minor issues"

* tag 'spi-fix-v5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: spi-sun6i: sun6i_spi_transfer_one(): fix setting of clock rate
  spi: mediatek: use correct SPI_CFG2_REG MACRO

Merge tag 'regulator-fix-v5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into master

Pull regulator fixes from Mark Brown:
 "The more substantial fix here is the rename of the da903x driver which
  fixes a collision with the parent MFD driver name which caused issues
  when things were built as modules.

  There's also a fix for a mislableled regulator on the pmi8994 which is
  quite important for systems with that device"

* tag 'regulator-fix-v5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  MAINTAINERS: remove obsolete entry after file renaming
  regulator: rename da903x to da903x-regulator
  regulator: qcom_smd: Fix pmi8994 label

Merge tag 'regmap-fix-v5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into master

Pull regmap fixes from Mark Brown:
 "A couple of substantial fixes here, one from Doug which fixes the
  debugfs code for MMIO regmaps (fortunately not the common case) and
  one from Marc fixing lookups of multiple regmaps for the same device
  (a very unusual case).

  There's also a fix for Kconfig to ensure we enable SoundWire properly"

* tag 'regmap-fix-v5.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: debugfs: Don't sleep while atomic for fast_io regmaps
  regmap: add missing dependency on SoundWire
  regmap: dev_get_regmap_match(): fix string comparison

Pull HID fixes from Jiri Kosina:

 - linked list race condition fix in hid-steam driver from Rodrigo Rivas
   Costa

 - assorted deviceID-specific quirks and other small cosmetic cleanups

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
  HID: logitech-hidpp: avoid repeated "multiplier = " log messages
  HID: logitech: Use HIDPP_RECEIVER_INDEX instead of 0xff
  HID: quirks: Ignore Simply Automated UPB PIM
  HID: apple: Disable Fn-key key-re-mapping on clone keyboards
  MAINTAINERS: update uhid and hid-wiimote entry
  HID: steam: fixes race in handling device list.
  HID: magicmouse: do not set up autorepeat
  HID: alps: support devices with report id 2
  HID: quirks: Always poll Obins Anne Pro 2 keyboard
  HID: i2c-hid: add Mediacom FlexBook edge13 to descriptor override

While digging through the recent mmiowb preemption issue it came up that
we aren't actually preventing IO from crossing a scheduling boundary.
While it's a bit ugly to overload smp_mb__after_spinlock() with this
behavior, it's what PowerPC is doing so there's some precedent.
Signed-off-by: NPalmer Dabbelt <palmerdabbelt@google.com>

Merge tag 'socfpga_fixes_for_v5.8_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/fixes

arm/arm64: dts: socfpga: fixes for v5.8
- Add status = "okay" in QSPI
- Increase QSPI size in reg property
- Fix dtschema for SoCFPGA platforms

* tag 'socfpga_fixes_for_v5.8_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
  arm64: dts: spcfpga: Align GIC, NAND and UART nodenames with dtschema
  ARM: dts: socfpga: Align L2 cache-controller nodename with dtschema
  arm64: dts: stratix10: increase QSPI reg address in nand dts file
  arm64: dts: stratix10: add status to qspi dts node
  arm64: dts: agilex: add status to qspi dts node

Link: https://lore.kernel.org/r/20200717155758.18233-1-dinguyen@kernel.orgSigned-off-by: NArnd Bergmann <arnd@arndb.de>

Merge tag 'renesas-fixes-for-v5.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/fixes

Renesas fixes for v5.8

  - Replace CONFIG_PCIE_RCAR by CONFIG_PCIE_RCAR_HOST in the defconfig,
    to unblock a planned Kconfig change.

* tag 'renesas-fixes-for-v5.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
  arm64: defconfig: Enable CONFIG_PCIE_RCAR_HOST

Link: https://lore.kernel.org/r/20200717100523.15418-1-geert+renesas@glider.beSigned-off-by: NArnd Bergmann <arnd@arndb.de>

Pull sound fixes from Takashi Iwai:
 "No surprise here, just a few device-specific small fixes: two fixes
  for USB LINE6 and one for USB-audio drivers wrt syzkaller fuzzer
  issues, while the rest are all HD-audio Realtek quirks"

* tag 'sound-5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda/realtek - fixup for yet another Intel reference board
  ALSA: hda/realtek - Enable Speaker for ASUS UX563
  ALSA: hda/realtek - Enable Speaker for ASUS UX533 and UX534
  ALSA: hda/realtek: Enable headset mic of Acer TravelMate B311R-31 with ALC256
  ALSA: hda/realtek: enable headset mic of ASUS ROG Zephyrus G14(G401) series with ALC289
  ALSA: hda/realtek - change to suitable link model for ASUS platform
  ALSA: usb-audio: Fix race against the error recovery URB submission
  ALSA: line6: Sync the pending work cancel at disconnection
  ALSA: line6: Perform sanity check for each URB creation