Reset only the index part of the mkey and keep the variant part. On
devlink reload, driver recreates mkeys, so the mkey index may change.
Trying to preserve the variant part of the mkey, driver mistakenly
merged the mkey index with current value. In case of a devlink reload,
current value of index part is dirty, so the index may be corrupted.

Fixes: 54c62e13 ("{IB,net}/mlx5: Setup mkey variant before mr create command invocation")
Signed-off-by: NAya Levin <ayal@nvidia.com>
Signed-off-by: NAmir Tzin <amirtz@nvidia.com>
Reviewed-by: NTariq Toukan <tariqt@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

Running devlink reload command for port in switchdev mode cause
resources to corrupt: driver can't release allocated EQ and reclaim
memory pages, because "rdma" auxiliary device had add CQs which blocks
EQ from deletion.
Erroneous sequence happens during reload-down phase, and is following:

1. detach device - suspends auxiliary devices which support it, destroys
   others. During this step "eth-rep" and "rdma-rep" are destroyed,
   "eth" - suspended.
2. disable SRIOV - moves device to legacy mode; as part of disablement -
   rescans drivers. This step adds "rdma" auxiliary device.
3. destroy EQ table - <failure>.

Driver shouldn't create any device during unload flows. To handle that
implement MLX5_PRIV_FLAGS_DETACH flag, set it on device detach and unset
on device attach. If flag is set do no-op on drivers rescan.

Fixes: a925b5e3 ("net/mlx5: Register mlx5 devices to auxiliary virtual bus")
Signed-off-by: NDmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: NLeon Romanovsky <leonro@nvidia.com>
Reviewed-by: NRoi Dayan <roid@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

Decapsulation L3 on small inner packets which are less than
64 Bytes was done incorrectly. In small packets there is an
extra padding added in L2 which should not be included in L3
length. The issue was that after decapL3 the extra L2 padding
caused an update on the L3 length.

To avoid this issue the new header is pushed to the beginning
of the packet (offset 0) which should not cause a HW reparse
and update the L3 length.

Fixes: c349b413 ("net/mlx5: DR, Add STEv1 modify header logic")
Reviewed-by: NErez Shitrit <erezsh@nvidia.com>
Reviewed-by: NYevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: NAlex Vesker <valex@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

When auxiliary bus autoprobe is disabled and SF is in ACTIVE state,
on SF port deletion it transitions from ACTIVE->ALLOCATED->INVALID.

When VHCA event handler queries the state, it is already transition
to INVALID state.

In this scenario, event handler missed to delete the SF device.

Fix it by deleting the SF when SF state is INVALID.

Fixes: 90d010b8 ("net/mlx5: SF, Add auxiliary device support")
Signed-off-by: NParav Pandit <parav@nvidia.com>
Reviewed-by: NVu Pham <vuhuong@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

E-switch should be able to set the GUID of host PF vport.
Currently it returns an error. This results in below error
when user attempts to configure MAC address of the PF of an
external controller.

$ devlink port function set pci/0000:03:00.0/196608 \
   hw_addr 00:00:00:11:22:33

mlx5_core 0000:03:00.0: mlx5_esw_set_vport_mac_locked:1876:(pid 6715):\
"Failed to set vport 0 node guid, err = -22.
RDMA_CM will not function properly for this VF."

Check for zero vport is no longer needed.

Fixes: 330077d1 ("net/mlx5: E-switch, Supporting setting devlink port function mac address")
Signed-off-by: NYuval Avnery <yuvalav@nvidia.com>
Signed-off-by: NParav Pandit <parav@nvidia.com>
Reviewed-by: NBodong Wang <bodong@nvidia.com>
Reviewed-by: NAlaa Hleihel <alaa@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

External controller PF's MAC address is not read from the device during
vport setup. Fail to read this results in showing all zeros to user
while the factory programmed MAC is a valid value.

$ devlink port show eth1 -jp
{
    "port": {
        "pci/0000:03:00.0/196608": {
            "type": "eth",
            "netdev": "eth1",
            "flavour": "pcipf",
            "controller": 1,
            "pfnum": 0,
            "splittable": false,
            "function": {
                "hw_addr": "00:00:00:00:00:00"
            }
        }
    }
}

Hence, read it when enabling a vport.

After the fix,

$ devlink port show eth1 -jp
{
    "port": {
        "pci/0000:03:00.0/196608": {
            "type": "eth",
            "netdev": "eth1",
            "flavour": "pcipf",
            "controller": 1,
            "pfnum": 0,
            "splittable": false,
            "function": {
                "hw_addr": "98:03:9b:a0:60:11"
            }
        }
    }
}

Fixes: f099fde1 ("net/mlx5: E-switch, Support querying port function mac address")
Signed-off-by: NBodong Wang <bodong@nvidia.com>
Signed-off-by: NParav Pandit <parav@nvidia.com>
Reviewed-by: NAlaa Hleihel <alaa@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

The device can be requested to be attached despite being not probed.
This situation is possible if devlink reload races with module removal,
and the following kernel panic is an outcome of such race.

 mlx5_core 0000:00:09.0: firmware version: 4.7.9999
 mlx5_core 0000:00:09.0: 0.000 Gb/s available PCIe bandwidth (8.0 GT/s PCIe x255 link)
 BUG: unable to handle page fault for address: fffffffffffffff0
 #PF: supervisor read access in kernel mode
 #PF: error_code(0x0000) - not-present page
 PGD 3218067 P4D 3218067 PUD 321a067 PMD 0
 Oops: 0000 [#1] SMP KASAN NOPTI
 CPU: 7 PID: 250 Comm: devlink Not tainted 5.12.0-rc2+ #2836
 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
 RIP: 0010:mlx5_attach_device+0x80/0x280 [mlx5_core]
 Code: f8 48 c1 e8 03 42 80 3c 38 00 0f 85 80 01 00 00 48 8b 45 68 48 8d 78 f0 48 89 fe 48 c1 ee 03 42 80 3c 3e 00 0f 85 70 01 00 00 <48> 8b 40 f0 48 85 c0 74 0d 48 89 ef ff d0 85 c0 0f 85 84 05 0e 00
 RSP: 0018:ffff8880129675f0 EFLAGS: 00010246
 RAX: 0000000000000000 RBX: 0000000000000001 RCX: ffffffff827407f1
 RDX: 1ffff110011336cf RSI: 1ffffffffffffffe RDI: fffffffffffffff0
 RBP: ffff888008e0c000 R08: 0000000000000008 R09: ffffffffa0662ee7
 R10: fffffbfff40cc5dc R11: 0000000000000000 R12: ffff88800ea002e0
 R13: ffffed1001d459f7 R14: ffffffffa05ef4f8 R15: dffffc0000000000
 FS:  00007f51dfeaf740(0000) GS:ffff88806d5c0000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: fffffffffffffff0 CR3: 000000000bc82006 CR4: 0000000000370ea0
 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
 Call Trace:
  mlx5_load_one+0x117/0x1d0 [mlx5_core]
  devlink_reload+0x2d5/0x520
  ? devlink_remote_reload_actions_performed+0x30/0x30
  ? mutex_trylock+0x24b/0x2d0
  ? devlink_nl_cmd_reload+0x62b/0x1070
  devlink_nl_cmd_reload+0x66d/0x1070
  ? devlink_reload+0x520/0x520
  ? devlink_nl_pre_doit+0x64/0x4d0
  genl_family_rcv_msg_doit+0x1e9/0x2f0
  ? mutex_lock_io_nested+0x1130/0x1130
  ? genl_family_rcv_msg_attrs_parse.constprop.0+0x240/0x240
  ? security_capable+0x51/0x90
  genl_rcv_msg+0x27f/0x4a0
  ? genl_get_cmd+0x3c0/0x3c0
  ? lock_acquire+0x1a9/0x6d0
  ? devlink_reload+0x520/0x520
  ? lock_release+0x6c0/0x6c0
  netlink_rcv_skb+0x11d/0x340
  ? genl_get_cmd+0x3c0/0x3c0
  ? netlink_ack+0x9f0/0x9f0
  ? lock_release+0x1f9/0x6c0
  genl_rcv+0x24/0x40
  netlink_unicast+0x433/0x700
  ? netlink_attachskb+0x730/0x730
  ? _copy_from_iter_full+0x178/0x650
  ? __alloc_skb+0x113/0x2b0
  netlink_sendmsg+0x6f1/0xbd0
  ? netlink_unicast+0x700/0x700
  ? netlink_unicast+0x700/0x700
  sock_sendmsg+0xb0/0xe0
  __sys_sendto+0x193/0x240
  ? __x64_sys_getpeername+0xb0/0xb0
  ? copy_page_range+0x2300/0x2300
  ? __up_read+0x1a1/0x7b0
  ? do_user_addr_fault+0x219/0xdc0
  __x64_sys_sendto+0xdd/0x1b0
  ? syscall_enter_from_user_mode+0x1d/0x50
  do_syscall_64+0x2d/0x40
  entry_SYSCALL_64_after_hwframe+0x44/0xae
 RIP: 0033:0x7f51dffb514a
 Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca 64 8b 04 25 18 00 00 00 85 c0 75 15 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 76 c3 0f 1f 44 00 00 55 48 83 ec 30 44 89 4c
 RSP: 002b:00007ffcaef22e78 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
 RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00007f51dffb514a
 RDX: 0000000000000030 RSI: 000055750daf2440 RDI: 0000000000000003
 RBP: 000055750daf2410 R08: 00007f51e0081200 R09: 000000000000000c
 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
 Modules linked in: mlx5_core(-) ptp pps_core ib_ipoib rdma_ucm rdma_cm iw_cm ib_cm ib_umad ib_uverbs ib_core [last unloaded: mlx5_ib]
 CR2: fffffffffffffff0
 ---[ end trace 7789831bfe74fa42 ]---

Fixes: a925b5e3 ("net/mlx5: Register mlx5 devices to auxiliary virtual bus")
Signed-off-by: NLeon Romanovsky <leonro@nvidia.com>
Reviewed-by: NParav Pandit <parav@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

In the case of the failure to execute mlx5_core_set_hca_defaults(),
we used wrong goto label to execute error unwind flow.

Fixes: 5bef709d ("net/mlx5: Enable host PF HCA after eswitch is initialized")
Reviewed-by: NSaeed Mahameed <saeedm@nvidia.com>
Reviewed-by: NMoshe Shemesh <moshe@nvidia.com>
Signed-off-by: NLeon Romanovsky <leonro@nvidia.com>
Reviewed-by: NParav Pandit <parav@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields.

The memcpy() is copying the entire structure, not just the first array.
Adjust the source argument so the compiler can do appropriate bounds
checking.
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields.

The memcpy() is copying the entire structure, not just the first array.
Adjust the source argument so the compiler can do appropriate bounds
checking.
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields.

The memcpy() is copying the entire structure, not just the first array.
Adjust the source argument so the compiler can do appropriate bounds
checking.
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

udpgro_fwd.sh contains many bash specific operators ("[[", "local -r"),
but it's using /bin/sh; in some distro /bin/sh is mapped to /bin/dash,
that doesn't support such operators.

Force the test to use /bin/bash explicitly and prevent false positive
test failures.
Signed-off-by: NAndrea Righi <andrea.righi@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While unix_may_send(sk, osk) is called while osk is locked, it appears
unix_release_sock() can overwrite unix_peer() after this lock has been
released, making KCSAN unhappy.

Changing unix_release_sock() to access/change unix_peer()
before lock is released should fix this issue.

BUG: KCSAN: data-race in unix_dgram_sendmsg / unix_release_sock

write to 0xffff88810465a338 of 8 bytes by task 20852 on cpu 1:
 unix_release_sock+0x4ed/0x6e0 net/unix/af_unix.c:558
 unix_release+0x2f/0x50 net/unix/af_unix.c:859
 __sock_release net/socket.c:599 [inline]
 sock_close+0x6c/0x150 net/socket.c:1258
 __fput+0x25b/0x4e0 fs/file_table.c:280
 ____fput+0x11/0x20 fs/file_table.c:313
 task_work_run+0xae/0x130 kernel/task_work.c:164
 tracehook_notify_resume include/linux/tracehook.h:189 [inline]
 exit_to_user_mode_loop kernel/entry/common.c:175 [inline]
 exit_to_user_mode_prepare+0x156/0x190 kernel/entry/common.c:209
 __syscall_exit_to_user_mode_work kernel/entry/common.c:291 [inline]
 syscall_exit_to_user_mode+0x20/0x40 kernel/entry/common.c:302
 do_syscall_64+0x56/0x90 arch/x86/entry/common.c:57
 entry_SYSCALL_64_after_hwframe+0x44/0xae

read to 0xffff88810465a338 of 8 bytes by task 20888 on cpu 0:
 unix_may_send net/unix/af_unix.c:189 [inline]
 unix_dgram_sendmsg+0x923/0x1610 net/unix/af_unix.c:1712
 sock_sendmsg_nosec net/socket.c:654 [inline]
 sock_sendmsg net/socket.c:674 [inline]
 ____sys_sendmsg+0x360/0x4d0 net/socket.c:2350
 ___sys_sendmsg net/socket.c:2404 [inline]
 __sys_sendmmsg+0x315/0x4b0 net/socket.c:2490
 __do_sys_sendmmsg net/socket.c:2519 [inline]
 __se_sys_sendmmsg net/socket.c:2516 [inline]
 __x64_sys_sendmmsg+0x53/0x60 net/socket.c:2516
 do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47
 entry_SYSCALL_64_after_hwframe+0x44/0xae

value changed: 0xffff888167905400 -> 0x0000000000000000

Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 20888 Comm: syz-executor.0 Not tainted 5.13.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: Nsyzbot <syzkaller@googlegroups.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

veth.sh is a shell script that uses /bin/sh; some distro (Ubuntu for
example) use dash as /bin/sh and in this case the test reports the
following error:

 # ./veth.sh: 21: local: -r: bad variable name
 # ./veth.sh: 21: local: -r: bad variable name

This happens because dash doesn't support the option "-r" with local.

Moreover, in case of missing bpf object, the script is exiting -1, that
is an illegal number for dash:

 exit: Illegal number: -1

Change the script to be compatible both with bash and dash and prevent
the errors above.
Signed-off-by: NAndrea Righi <andrea.righi@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
net/packet: annotate data races

KCSAN sent two reports about data races in af_packet.
Nothing serious, but worth fixing.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Like prior patch, we need to annotate lockless accesses to po->ifindex
For instance, packet_getname() is reading po->ifindex (twice) while
another thread is able to change po->ifindex.

KCSAN reported:

BUG: KCSAN: data-race in packet_do_bind / packet_getname

write to 0xffff888143ce3cbc of 4 bytes by task 25573 on cpu 1:
 packet_do_bind+0x420/0x7e0 net/packet/af_packet.c:3191
 packet_bind+0xc3/0xd0 net/packet/af_packet.c:3255
 __sys_bind+0x200/0x290 net/socket.c:1637
 __do_sys_bind net/socket.c:1648 [inline]
 __se_sys_bind net/socket.c:1646 [inline]
 __x64_sys_bind+0x3d/0x50 net/socket.c:1646
 do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47
 entry_SYSCALL_64_after_hwframe+0x44/0xae

read to 0xffff888143ce3cbc of 4 bytes by task 25578 on cpu 0:
 packet_getname+0x5b/0x1a0 net/packet/af_packet.c:3525
 __sys_getsockname+0x10e/0x1a0 net/socket.c:1887
 __do_sys_getsockname net/socket.c:1902 [inline]
 __se_sys_getsockname net/socket.c:1899 [inline]
 __x64_sys_getsockname+0x3e/0x50 net/socket.c:1899
 do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47
 entry_SYSCALL_64_after_hwframe+0x44/0xae

value changed: 0x00000000 -> 0x00000001

Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 25578 Comm: syz-executor.5 Not tainted 5.13.0-rc6-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: Nsyzbot <syzkaller@googlegroups.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tpacket_snd(), packet_snd(), packet_getname() and packet_seq_show()
can read po->num without holding a lock. This means other threads
can change po->num at the same time.

KCSAN complained about this known fact [1]
Add READ_ONCE()/WRITE_ONCE() to address the issue.

[1] BUG: KCSAN: data-race in packet_do_bind / packet_sendmsg

write to 0xffff888131a0dcc0 of 2 bytes by task 24714 on cpu 0:
 packet_do_bind+0x3ab/0x7e0 net/packet/af_packet.c:3181
 packet_bind+0xc3/0xd0 net/packet/af_packet.c:3255
 __sys_bind+0x200/0x290 net/socket.c:1637
 __do_sys_bind net/socket.c:1648 [inline]
 __se_sys_bind net/socket.c:1646 [inline]
 __x64_sys_bind+0x3d/0x50 net/socket.c:1646
 do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47
 entry_SYSCALL_64_after_hwframe+0x44/0xae

read to 0xffff888131a0dcc0 of 2 bytes by task 24719 on cpu 1:
 packet_snd net/packet/af_packet.c:2899 [inline]
 packet_sendmsg+0x317/0x3570 net/packet/af_packet.c:3040
 sock_sendmsg_nosec net/socket.c:654 [inline]
 sock_sendmsg net/socket.c:674 [inline]
 ____sys_sendmsg+0x360/0x4d0 net/socket.c:2350
 ___sys_sendmsg net/socket.c:2404 [inline]
 __sys_sendmsg+0x1ed/0x270 net/socket.c:2433
 __do_sys_sendmsg net/socket.c:2442 [inline]
 __se_sys_sendmsg net/socket.c:2440 [inline]
 __x64_sys_sendmsg+0x42/0x50 net/socket.c:2440
 do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47
 entry_SYSCALL_64_after_hwframe+0x44/0xae

value changed: 0x0000 -> 0x1200

Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 24719 Comm: syz-executor.5 Not tainted 5.13.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: Nsyzbot <syzkaller@googlegroups.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-5.13-20210616' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2021-06-16

this is a pull request of 4 patches for net/master.

The first patch is by Oleksij Rempel and fixes a Use-after-Free found
by syzbot in the j1939 stack.

The next patch is by Tetsuo Handa and fixes hung task detected by
syzbot in the bcm, raw and isotp protocols.

Norbert Slusarek's patch fixes a infoleak in bcm's struct
bcm_msg_head.

Pavel Skripkin's patch fixes a memory leak in the mcba_usb driver.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BUG: memory leak
unreferenced object 0xffff888101bc4c00 (size 32):
  comm "syz-executor527", pid 360, jiffies 4294807421 (age 19.329s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
    01 00 00 00 00 00 00 00 ac 14 14 bb 00 00 02 00 ................
  backtrace:
    [<00000000f17c5244>] kmalloc include/linux/slab.h:558 [inline]
    [<00000000f17c5244>] kzalloc include/linux/slab.h:688 [inline]
    [<00000000f17c5244>] ip_mc_add1_src net/ipv4/igmp.c:1971 [inline]
    [<00000000f17c5244>] ip_mc_add_src+0x95f/0xdb0 net/ipv4/igmp.c:2095
    [<000000001cb99709>] ip_mc_source+0x84c/0xea0 net/ipv4/igmp.c:2416
    [<0000000052cf19ed>] do_ip_setsockopt net/ipv4/ip_sockglue.c:1294 [inline]
    [<0000000052cf19ed>] ip_setsockopt+0x114b/0x30c0 net/ipv4/ip_sockglue.c:1423
    [<00000000477edfbc>] raw_setsockopt+0x13d/0x170 net/ipv4/raw.c:857
    [<00000000e75ca9bb>] __sys_setsockopt+0x158/0x270 net/socket.c:2117
    [<00000000bdb993a8>] __do_sys_setsockopt net/socket.c:2128 [inline]
    [<00000000bdb993a8>] __se_sys_setsockopt net/socket.c:2125 [inline]
    [<00000000bdb993a8>] __x64_sys_setsockopt+0xba/0x150 net/socket.c:2125
    [<000000006a1ffdbd>] do_syscall_64+0x40/0x80 arch/x86/entry/common.c:47
    [<00000000b11467c4>] entry_SYSCALL_64_after_hwframe+0x44/0xae

In commit 24803f38 ("igmp: do not remove igmp souce list info when set
link down"), the ip_mc_clear_src() in ip_mc_destroy_dev() was removed,
because it was also called in igmpv3_clear_delrec().

Rough callgraph:

inetdev_destroy
-> ip_mc_destroy_dev
     -> igmpv3_clear_delrec
        -> ip_mc_clear_src
-> RCU_INIT_POINTER(dev->ip_ptr, NULL)

However, ip_mc_clear_src() called in igmpv3_clear_delrec() doesn't
release in_dev->mc_list->sources. And RCU_INIT_POINTER() assigns the
NULL to dev->ip_ptr. As a result, in_dev cannot be obtained through
inetdev_by_index() and then in_dev->mc_list->sources cannot be released
by ip_mc_del1_src() in the sock_close. Rough call sequence goes like:

sock_close
-> __sock_release
   -> inet_release
      -> ip_mc_drop_socket
         -> inetdev_by_index
         -> ip_mc_leave_src
            -> ip_mc_del_src
               -> ip_mc_del1_src

So we still need to call ip_mc_clear_src() in ip_mc_destroy_dev() to free
in_dev->mc_list->sources.

Fixes: 24803f38 ("igmp: do not remove igmp souce list info ...")
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NChengyang Fan <cy.fan@huawei.com>
Acked-by: NHangbin Liu <liuhangbin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Joakim Zhang says:

====================
net: fixes for fec ptp

Small fixes for fec ptp.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit da722186 ("net: fec: set GPR bit on suspend by DT configuration.")
refactor the fec_devtype, need adjust ptp driver accordingly.

Fixes: da722186 ("net: fec: set GPR bit on suspend by DT configuration.")
Signed-off-by: NJoakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add clock rate zero check to fix coverity issue of "divide by 0".

Fixes: commit 85bd1798 ("net: fec: fix spin_lock dead lock")
Signed-off-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NJoakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit 46a8b29c ("net: usb: fix memory leak in smsc75xx_bind")
fails to clean up the work scheduled in smsc75xx_reset->
smsc75xx_set_multicast, which leads to use-after-free if the work is
scheduled to start after the deallocation. In addition, this patch
also removes a dangling pointer - dev->data[0].

This patch calls cancel_work_sync to cancel the scheduled work and set
the dangling pointer to NULL.

Fixes: 46a8b29c ("net: usb: fix memory leak in smsc75xx_bind")
Signed-off-by: NDongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Platform drivers may call stmmac_probe_config_dt() to parse dt, could
call stmmac_remove_config_dt() in error handing after dt parsed, so need
disable clocks in stmmac_remove_config_dt().

Go through all platforms drivers which use stmmac_probe_config_dt(),
none of them disable clocks manually, so it's safe to disable them in
stmmac_remove_config_dt().

Fixes: commit d2ed0a77 ("net: ethernet: stmmac: fix of-node and fixed-link-phydev leaks")
Signed-off-by: NJoakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Syzbot reported memory leak in SocketCAN driver for Microchip CAN BUS
Analyzer Tool. The problem was in unfreed usb_coherent.

In mcba_usb_start() 20 coherent buffers are allocated and there is
nothing, that frees them:

1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
   is not set (see mcba_usb_start) and this flag cannot be used with
   coherent buffers.

Fail log:
| [ 1354.053291][ T8413] mcba_usb 1-1:0.0 can0: device disconnected
| [ 1367.059384][ T8420] kmemleak: 20 new suspected memory leaks (see /sys/kernel/debug/kmem)

So, all allocated buffers should be freed with usb_free_coherent()
explicitly

NOTE:
The same pattern for allocating and freeing coherent buffers
is used in drivers/net/can/usb/kvaser_usb/kvaser_usb_core.c

Fixes: 51f3baad ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer")
Link: https://lore.kernel.org/r/20210609215833.30393-1-paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+57281c762a3922e14dfe@syzkaller.appspotmail.com
Signed-off-by: NPavel Skripkin <paskripkin@gmail.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

On 64-bit systems, struct bcm_msg_head has an added padding of 4 bytes between
struct members count and ival1. Even though all struct members are initialized,
the 4-byte hole will contain data from the kernel stack. This patch zeroes out
struct bcm_msg_head before usage, preventing infoleaks to userspace.

Fixes: ffd980f9 ("[CAN]: Add broadcast manager (bcm) protocol")
Link: https://lore.kernel.org/r/trinity-7c1b2e82-e34f-4885-8060-2cd7a13769ce-1623532166177@3c-app-gmx-bs52
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NNorbert Slusarek <nslusarek@gmx.net>
Acked-by: NOliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

syzbot is reporting hung task at register_netdevice_notifier() [1] and
unregister_netdevice_notifier() [2], for cleanup_net() might perform
time consuming operations while CAN driver's raw/bcm/isotp modules are
calling {register,unregister}_netdevice_notifier() on each socket.

Change raw/bcm/isotp modules to call register_netdevice_notifier() from
module's __init function and call unregister_netdevice_notifier() from
module's __exit function, as with gw/j1939 modules are doing.

Link: https://syzkaller.appspot.com/bug?id=391b9498827788b3cc6830226d4ff5be87107c30 [1]
Link: https://syzkaller.appspot.com/bug?id=1724d278c83ca6e6df100a2e320c10d991cf2bce [2]
Link: https://lore.kernel.org/r/54a5f451-05ed-f977-8534-79e7aa2bcc8f@i-love.sakura.ne.jp
Cc: linux-stable <stable@vger.kernel.org>
Reported-by: Nsyzbot <syzbot+355f8edb2ff45d5f95fa@syzkaller.appspotmail.com>
Reported-by: Nsyzbot <syzbot+0f1827363a305f74996f@syzkaller.appspotmail.com>
Reviewed-by: NKirill Tkhai <ktkhai@virtuozzo.com>
Tested-by: Nsyzbot <syzbot+355f8edb2ff45d5f95fa@syzkaller.appspotmail.com>
Tested-by: NOliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch fixes a Use-after-Free found by the syzbot.

The problem is that a skb is taken from the per-session skb queue,
without incrementing the ref count. This leads to a Use-after-Free if
the skb is taken concurrently from the session queue due to a CTS.

Fixes: 9d71dd0c ("can: add support of SAE J1939 protocol")
Link: https://lore.kernel.org/r/20210521115720.7533-1-o.rempel@pengutronix.de
Cc: Hillf Danton <hdanton@sina.com>
Cc: linux-stable <stable@vger.kernel.org>
Reported-by: syzbot+220c1a29987a9a490903@syzkaller.appspotmail.com
Reported-by: syzbot+45199c1b73b4013525cf@syzkaller.appspotmail.com
Signed-off-by: NOleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Daniel Borkmann says:

====================
pull-request: bpf 2021-06-15

The following pull-request contains BPF updates for your *net* tree.

We've added 5 non-merge commits during the last 11 day(s) which contain
a total of 10 files changed, 115 insertions(+), 16 deletions(-).

The main changes are:

1) Fix marking incorrect umem ring as done in libbpf's
   xsk_socket__create_shared() helper, from Kev Jackson.

2) Fix oob leakage under a spectre v1 type confusion
   attack, from Daniel Borkmann.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The previous commit didn't fix the bug properly. By mistake, it replaces
the pointer of the next skb in the descriptor ring instead of the current
one. As a result, the two descriptors are assigned the same SKB. The error
is seen during the iperf test when skb_put tries to insert a second packet
and exceeds the available buffer.

Fixes: c7718ee9 ("net: lantiq: fix memory corruption in RX ring ")
Signed-off-by: NAleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the QMI_WWAN_FLAG_PASS_THROUGH is set, netif_rx() is called from
qmi_wwan_rx_fixup(). When the call to netif_rx() is successful (which is
most of the time), usbnet_skb_return() is called (from rx_process()).
usbnet_skb_return() will then call netif_rx() a second time for the same
skb.

Simplify the code and avoid the redundant netif_rx() call by changing
qmi_wwan_rx_fixup() to always return 1 when QMI_WWAN_FLAG_PASS_THROUGH
is set. We then leave it up to the existing infrastructure to call
netif_rx().
Suggested-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NKristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is meant to make the host side cdc_ncm interface consistently
named just like the older CDC protocols: cdc_ether & cdc_ecm
(and even rndis_host), which all use 'FLAG_ETHER | FLAG_POINTTOPOINT'.

include/linux/usb/usbnet.h:
  #define FLAG_ETHER	0x0020		/* maybe use "eth%d" names */
  #define FLAG_WLAN	0x0080		/* use "wlan%d" names */
  #define FLAG_WWAN	0x0400		/* use "wwan%d" names */
  #define FLAG_POINTTOPOINT 0x1000	/* possibly use "usb%d" names */

drivers/net/usb/usbnet.c @ line 1711:
  strcpy (net->name, "usb%d");
  ...
  // heuristic:  "usb%d" for links we know are two-host,
  // else "eth%d" when there's reasonable doubt.  userspace
  // can rename the link if it knows better.
  if ((dev->driver_info->flags & FLAG_ETHER) != 0 &&
      ((dev->driver_info->flags & FLAG_POINTTOPOINT) == 0 ||
       (net->dev_addr [0] & 0x02) == 0))
          strcpy (net->name, "eth%d");
  /* WLAN devices should always be named "wlan%d" */
  if ((dev->driver_info->flags & FLAG_WLAN) != 0)
          strcpy(net->name, "wlan%d");
  /* WWAN devices should always be named "wwan%d" */
  if ((dev->driver_info->flags & FLAG_WWAN) != 0)
          strcpy(net->name, "wwan%d");

So by using ETHER | POINTTOPOINT the interface naming is
either usb%d or eth%d based on the global uniqueness of the
mac address of the device.

Without this 2.5gbps ethernet dongles which all seem to use the cdc_ncm
driver end up being called usb%d instead of eth%d even though they're
definitely not two-host.  (All 1gbps & 5gbps ethernet usb dongles I've
tested don't hit this problem due to use of different drivers, primarily
r8152 and aqc111)

Fixes tag is based purely on git blame, and is really just here to make
sure this hits LTS branches newer than v4.5.

Cc: Lorenzo Colitti <lorenzo@google.com>
Fixes: 4d06dd53 ("cdc_ncm: do not call usbnet_link_change from cdc_ncm_bind")
Signed-off-by: NMaciej Żenczykowski <maze@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function get_net_ns_by_fd() could be inlined when NET_NS is not
enabled.
Signed-off-by: NChangbin Du <changbin.du@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Scaled PPM conversion to PPB may (on 64bit systems) result
in a value larger than s32 can hold (freq/scaled_ppm is a long).
This means the kernel will not correctly reject unreasonably
high ->freq values (e.g. > 4294967295ppb, 281474976645 scaled PPM).

The conversion is equivalent to a division by ~66 (65.536),
so the value of ppb is always smaller than ppm, but not small
enough to assume narrowing the type from long -> s32 is okay.

Note that reasonable user space (e.g. ptp4l) will not use such
high values, anyway, 4289046510ppb ~= 4.3x, so the fix is
somewhat pedantic.

Fixes: d39a7435 ("ptp: validate the requested frequency adjustment.")
Fixes: d94ba80e ("ptp: Added a brand new class driver for ptp clocks.")
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update the function prototype of mhi_ndo_xmit to match
ndo_start_xmit. This otherwise leads to run time failures when
CFI is enabled in kernel.

Fixes: 3ffec6a1 ("net: Add mhi-net driver")
Signed-off-by: NSubash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In almost all cases from test_verifier that have been changed in here, we've
had an unreachable path with a load from a register which has an invalid
address on purpose. This was basically to make sure that we never walk this
path and to have the verifier complain if it would otherwise. Change it to
match on the right error for unprivileged given we now test these paths
under speculative execution.

There's one case where we match on exact # of insns_processed. Due to the
extra path, this will of course mismatch on unprivileged. Thus, restrict the
test->insn_processed check to privileged-only.

In one other case, we result in a 'pointer comparison prohibited' error. This
is similarly due to verifying an 'invalid' branch where we end up with a value
pointer on one side of the comparison.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Reviewed-by: NJohn Fastabend <john.fastabend@gmail.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>

The verifier only enumerates valid control-flow paths and skips paths that
are unreachable in the non-speculative domain. And so it can miss issues
under speculative execution on mispredicted branches.

For example, a type confusion has been demonstrated with the following
crafted program:

  // r0 = pointer to a map array entry
  // r6 = pointer to readable stack slot
  // r9 = scalar controlled by attacker
  1: r0 = *(u64 *)(r0) // cache miss
  2: if r0 != 0x0 goto line 4
  3: r6 = r9
  4: if r0 != 0x1 goto line 6
  5: r9 = *(u8 *)(r6)
  6: // leak r9

Since line 3 runs iff r0 == 0 and line 5 runs iff r0 == 1, the verifier
concludes that the pointer dereference on line 5 is safe. But: if the
attacker trains both the branches to fall-through, such that the following
is speculatively executed ...

  r6 = r9
  r9 = *(u8 *)(r6)
  // leak r9

... then the program will dereference an attacker-controlled value and could
leak its content under speculative execution via side-channel. This requires
to mistrain the branch predictor, which can be rather tricky, because the
branches are mutually exclusive. However such training can be done at
congruent addresses in user space using different branches that are not
mutually exclusive. That is, by training branches in user space ...

  A:  if r0 != 0x0 goto line C
  B:  ...
  C:  if r0 != 0x0 goto line D
  D:  ...

... such that addresses A and C collide to the same CPU branch prediction
entries in the PHT (pattern history table) as those of the BPF program's
lines 2 and 4, respectively. A non-privileged attacker could simply brute
force such collisions in the PHT until observing the attack succeeding.

Alternative methods to mistrain the branch predictor are also possible that
avoid brute forcing the collisions in the PHT. A reliable attack has been
demonstrated, for example, using the following crafted program:

  // r0 = pointer to a [control] map array entry
  // r7 = *(u64 *)(r0 + 0), training/attack phase
  // r8 = *(u64 *)(r0 + 8), oob address
  // [...]
  // r0 = pointer to a [data] map array entry
  1: if r7 == 0x3 goto line 3
  2: r8 = r0
  // crafted sequence of conditional jumps to separate the conditional
  // branch in line 193 from the current execution flow
  3: if r0 != 0x0 goto line 5
  4: if r0 == 0x0 goto exit
  5: if r0 != 0x0 goto line 7
  6: if r0 == 0x0 goto exit
  [...]
  187: if r0 != 0x0 goto line 189
  188: if r0 == 0x0 goto exit
  // load any slowly-loaded value (due to cache miss in phase 3) ...
  189: r3 = *(u64 *)(r0 + 0x1200)
  // ... and turn it into known zero for verifier, while preserving slowly-
  // loaded dependency when executing:
  190: r3 &= 1
  191: r3 &= 2
  // speculatively bypassed phase dependency
  192: r7 += r3
  193: if r7 == 0x3 goto exit
  194: r4 = *(u8 *)(r8 + 0)
  // leak r4

As can be seen, in training phase (phase != 0x3), the condition in line 1
turns into false and therefore r8 with the oob address is overridden with
the valid map value address, which in line 194 we can read out without
issues. However, in attack phase, line 2 is skipped, and due to the cache
miss in line 189 where the map value is (zeroed and later) added to the
phase register, the condition in line 193 takes the fall-through path due
to prior branch predictor training, where under speculation, it'll load the
byte at oob address r8 (unknown scalar type at that point) which could then
be leaked via side-channel.

One way to mitigate these is to 'branch off' an unreachable path, meaning,
the current verification path keeps following the is_branch_taken() path
and we push the other branch to the verification stack. Given this is
unreachable from the non-speculative domain, this branch's vstate is
explicitly marked as speculative. This is needed for two reasons: i) if
this path is solely seen from speculative execution, then we later on still
want the dead code elimination to kick in in order to sanitize these
instructions with jmp-1s, and ii) to ensure that paths walked in the
non-speculative domain are not pruned from earlier walks of paths walked in
the speculative domain. Additionally, for robustness, we mark the registers
which have been part of the conditional as unknown in the speculative path
given there should be no assumptions made on their content.

The fix in here mitigates type confusion attacks described earlier due to
i) all code paths in the BPF program being explored and ii) existing
verifier logic already ensuring that given memory access instruction
references one specific data structure.

An alternative to this fix that has also been looked at in this scope was to
mark aux->alu_state at the jump instruction with a BPF_JMP_TAKEN state as
well as direction encoding (always-goto, always-fallthrough, unknown), such
that mixing of different always-* directions themselves as well as mixing of
always-* with unknown directions would cause a program rejection by the
verifier, e.g. programs with constructs like 'if ([...]) { x = 0; } else
{ x = 1; }' with subsequent 'if (x == 1) { [...] }'. For unprivileged, this
would result in only single direction always-* taken paths, and unknown taken
paths being allowed, such that the former could be patched from a conditional
jump to an unconditional jump (ja). Compared to this approach here, it would
have two downsides: i) valid programs that otherwise are not performing any
pointer arithmetic, etc, would potentially be rejected/broken, and ii) we are
required to turn off path pruning for unprivileged, where both can be avoided
in this work through pushing the invalid branch to the verification stack.

The issue was originally discovered by Adam and Ofek, and later independently
discovered and reported as a result of Benedict and Piotr's research work.

Fixes: b2157399 ("bpf: prevent out-of-bounds speculation")
Reported-by: NAdam Morrison <mad@cs.tau.ac.il>
Reported-by: NOfek Kirzner <ofekkir@gmail.com>
Reported-by: NBenedict Schlueter <benedict.schlueter@rub.de>
Reported-by: NPiotr Krysiuk <piotras@gmail.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Reviewed-by: NJohn Fastabend <john.fastabend@gmail.com>
Reviewed-by: NBenedict Schlueter <benedict.schlueter@rub.de>
Reviewed-by: NPiotr Krysiuk <piotras@gmail.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>

... in such circumstances, we do not want to mark the instruction as seen given
the goal is still to jmp-1 rewrite/sanitize dead code, if it is not reachable
from the non-speculative path verification. We do however want to verify it for
safety regardless.

With the patch as-is all the insns that have been marked as seen before the
patch will also be marked as seen after the patch (just with a potentially
different non-zero count). An upcoming patch will also verify paths that are
unreachable in the non-speculative domain, hence this extension is needed.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Reviewed-by: NJohn Fastabend <john.fastabend@gmail.com>
Reviewed-by: NBenedict Schlueter <benedict.schlueter@rub.de>
Reviewed-by: NPiotr Krysiuk <piotras@gmail.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>

Instead of relying on current env->pass_cnt, use the seen count from the
old aux data in adjust_insn_aux_data(), and expand it to the new range of
patched instructions. This change is valid given we always expand 1:n
with n>=1, so what applies to the old/original instruction needs to apply
for the replacement as well.

Not relying on env->pass_cnt is a prerequisite for a later change where we
want to avoid marking an instruction seen when verified under speculative
execution path.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Reviewed-by: NJohn Fastabend <john.fastabend@gmail.com>
Reviewed-by: NBenedict Schlueter <benedict.schlueter@rub.de>
Reviewed-by: NPiotr Krysiuk <piotras@gmail.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>

Luiz Augusto von Dentz says:

====================
bluetooth pull request for net:

 - Fix crash on SMP when debug is enabled
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>