Complete the enablement of the cm framework feature in the adapter. Perform
the following:

 - Detect the presence of the congestion management framework feature.

When the cm framework is present:

 - Issue the SET_FEATURE command to enable the feature.

 - Register the cm statistics buffer with the adapter.

 - Read the cm enablement buffer to determine the cm framework state for cm
   management.

When cm management is enabled:

 - Monitor all FPIN and congestion signalling events, incrementing
   counters.

 - Regularly sync with the adapter to communicate congestion events and to
   receive an rx request limit.

 - Monitor requests for rx data and ensure that no more than the
   adapter prescribed limit is issued on the link. If the limit is
   exceeded, SCSI and/or NVMe traffic is temporarily suspended.

 - Maintain the minute, hourly, daily statistics buffer.

 - Monitor for congestion enablement change events, causing a reread of the
   enablement buffer and acting on any change in enablement.

And:

 - Add teardown logic, including buffer deregistration, on adapter
   detachment or reset.

Link: https://lore.kernel.org/r/20210816162901.121235-10-jsmart2021@gmail.comCo-developed-by: NJustin Tee <justin.tee@broadcom.com>
Signed-off-by: NJustin Tee <justin.tee@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When congestion mgmt is enabled, cmf has the driver regularly issue a
command to synchronize reporting of congestion mgmt events such as fpin and
signal delivery.

This patch adds the definition of the CMF_SYNC WQE and its CQE fields as
well as support for issuing the command. The patch also adds the few
remaining cmf-related SLI additions, such as feature definition for
enablement of CMF and notifications to the driver if the cm enablement mode
changes.

Link: https://lore.kernel.org/r/20210816162901.121235-9-jsmart2021@gmail.comCo-developed-by: NJustin Tee <justin.tee@broadcom.com>
Signed-off-by: NJustin Tee <justin.tee@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

As part of the cmf framework, the firmware maintains a table with
congestion related state information, specifically whether enabled and if
enabled, whether monitoring or actively managing congestion.

Add definition of the table and add support to read the table from the
adapter and determine if it is enabled. In support of this, the READ_OBJECT
mailbox command definition is added to the driver.

Link: https://lore.kernel.org/r/20210816162901.121235-8-jsmart2021@gmail.comCo-developed-by: NJustin Tee <justin.tee@broadcom.com>
Signed-off-by: NJustin Tee <justin.tee@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The cmf framework requires the driver to maintain a cm statistics table,
accessible inband, of congestion related statistics that are reported per
minute, rolled up to per hour, and rolled up again per day. Several days
worth may be maintained.  The table is registered with the adapter when the
MIB feature is enabled.

Add definition of the table and add support to register the table with the
adapter. Includes definition and initialization of event counters that are
later added to the statistics table.

Link: https://lore.kernel.org/r/20210816162901.121235-7-jsmart2021@gmail.comCo-developed-by: NJustin Tee <justin.tee@broadcom.com>
Signed-off-by: NJustin Tee <justin.tee@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When congestion management is enabled, issue EDC ELS to register congestion
signaling capabilities with the fabric. The response handling will process
the fabric parameters and set the reporting parameters.

Similarly, add support for receiving an EDC request from the fabric
generating a corresponding response.

Implement handlers for congestion signals from the fabric and maintain
statistics for them.

Link: https://lore.kernel.org/r/20210816162901.121235-6-jsmart2021@gmail.comCo-developed-by: NJustin Tee <justin.tee@broadcom.com>
Signed-off-by: NJustin Tee <justin.tee@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Expand FPIN logging:

 - Display Attached Port Names for Link Integrity and Peer Congestion
   events

 - Log Delivery, Peer Congestion, and Congestion events

 - Sanity check FPIN descriptor lengths when processing FPIN descriptors.

Log RDF events when congestion logging is enabled.

Link: https://lore.kernel.org/r/20210816162901.121235-5-jsmart2021@gmail.comCo-developed-by: NJustin Tee <justin.tee@broadcom.com>
Signed-off-by: NJustin Tee <justin.tee@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

MIB support is currently limited to detecting support in the adapter and
ensuring FDMI support is enabled if present.  For the new framework MIB
support also requires active enablement of support via the SET_FEATURES
command with the firmware.

Rework the MIB detection and enablement for the following:

 - Move detection away from the get_sli4_parameters routine, and into the
   hba_setup path. get_sli4_parameters is only called once at attachment
   while hba_setup is called as part of any SLI port reset path. This
   ensures detection after firmware download.

 - Update SET_FEATURES mbx command for the MIB enablement feature and add
   support for the feature.

 - Create the cmf_setup routine to encapsulate the detection of MIB support
   and perform the enablement of the MIB support feature.

Link: https://lore.kernel.org/r/20210816162901.121235-4-jsmart2021@gmail.comCo-developed-by: NJustin Tee <justin.tee@broadcom.com>
Signed-off-by: NJustin Tee <justin.tee@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Implement the SET_HOST_DATA mbox command to set date / time during
initialization.  It is used by the firmware for various purposes including
congestion management and firmware dumps.

Link: https://lore.kernel.org/r/20210816162901.121235-3-jsmart2021@gmail.comCo-developed-by: NJustin Tee <justin.tee@broadcom.com>
Signed-off-by: NJustin Tee <justin.tee@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add Exchange Diagnostic Capabilities (EDC) ELS definition and the following
capability descriptors:

 - Link Fault Capability Descriptor

 - Congestion Signaling Capability Descriptor

Definitions taken from FC-LS-5 r5.01

Link: https://lore.kernel.org/r/20210816162901.121235-2-jsmart2021@gmail.comSigned-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Change "allcation" to "allocation".

Link: https://lore.kernel.org/r/1891546521.01629282781634.JavaMail.epsvc@epcpadp4Signed-off-by: NKeoseong Park <keosung.park@samsung.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Driver is not setting up IRQs in the resume path. As a result, hibernation
path is broken and controller will not be operational after system is
resumed.

Set up IRQs to handle the hibernation case.

Link: https://lore.kernel.org/r/20210818081755.1274470-1-kashyap.desai@broadcom.com
Cc: sathya.prakash@broadcom.com
Cc: thenzl@redhat.com
Reported-by: NMarco Patalano <mpatalan@redhat.com>
Tested-by: NMarco Patalano <mpatalan@redhat.com>
Signed-off-by: NKashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Link: https://lore.kernel.org/r/20210823133458.3536824-1-pasic@linux.ibm.com
Fixes: f2542a3b ("scsi: scsi_ioctl: Move the "block layer" SCSI ioctl handling to drivers/scsi")
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NHalil Pasic <pasic@linux.ibm.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When HPB pinned region exists and mctx allocation for this region fails, a
memory leak is possible because memory is not released for the subregion
table of the current region.

Free memory for the subregion table of the current region.

Link: https://lore.kernel.org/r/1891546521.01629711601304.JavaMail.epsvc@epcpadp3Reviewed-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NKeoseong Park <keosung.park@samsung.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

There is a spelling mistake in a SNIC_HOST_INFO message. Fix it.

Link: https://lore.kernel.org/r/20210820151835.59804-1-colin.king@canonical.comSigned-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Link: https://lore.kernel.org/r/20210820095405.12801-4-hare@suse.deReviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

ncr_reset_bus() will complete all outstanding commands anyway, so there's
no need to single out a specific command.

Link: https://lore.kernel.org/r/20210820095405.12801-3-hare@suse.deReviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Always '1', so we can remove it.

Link: https://lore.kernel.org/r/20210820095405.12801-2-hare@suse.deReviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add FORCE so that if_changed can detect the command line change.
scsi_devinfo_tbl.c must be added to 'targets' too.

Link: https://lore.kernel.org/r/20210819012339.709409-1-masahiroy@kernel.orgSigned-off-by: NMasahiro Yamada <masahiroy@kernel.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Use scsi_cmd_to_rq(cmd)->tag instead of scsi_cmnd.tag as preference.

Link: https://lore.kernel.org/r/1629294801-32102-2-git-send-email-john.garry@huawei.comReviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Device reset and target reset will be using different calling sequences, so
open-code __qla2xxx_eh_generic_reset() in qla2xxx_eh_device_reset(), and
remove the now obsolete function __qla2xxx_eh_generic_reset().  No
functional changes.

Link: https://lore.kernel.org/r/20210819091913.94436-4-hare@suse.de
Cc: Nilesh Javali <njavali@marvell.com>
Reviewed-by: NNilesh Javali <njavali@marvell.com>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Device reset and target reset will be using different calling sequences, so
open-code __qla2xxx_eh_generic_reset() in qla2xxx_eh_target_reset().  No
functional changes.

Link: https://lore.kernel.org/r/20210819091913.94436-3-hare@suse.de
Cc: Nilesh Javali <njavali@marvell.com>
Reviewed-by: NNilesh Javali <njavali@marvell.com>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When calling bus reset the driver will be doing a full SAN resync, so there
is no need to wait for any pending RSCNs; they'll be re-issued during
resync anyway.

Link: https://lore.kernel.org/r/20210819091913.94436-2-hare@suse.de
Cc: Nilesh Javali <njavali@marvell.com>
Reviewed-by: NNilesh Javali <njavali@marvell.com>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Link: https://lore.kernel.org/r/20210817051315.2477-13-njavali@marvell.comSigned-off-by: NNilesh Javali <njavali@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

drivers/scsi/qla2xxx/qla_edif.c:213:25-29: Unneeded variable: "rval". Return "0"
on line 264

Remove unneeded variable used to store return value.

Generated by: scripts/coccinelle/misc/returnvar.cocci

Link: https://lore.kernel.org/r/20210817051315.2477-12-njavali@marvell.com
Fixes: 7ebb336e ("scsi: qla2xxx: edif: Add start + stop bsgs")
Reported-by: Nkernel test robot <lkp@intel.com>
Signed-off-by: Nkernel test robot <lkp@intel.com>
Signed-off-by: NNilesh Javali <njavali@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When Target port transitions personality from one to another (NVMe <-->
FCP), there could be some overlap of the two where one layer is going down
while the other layer is coming up. This overlap can cause temporary I/O
error. Detect those errors/transitions and recover from them. Triggers
session tear down and allow relogin to re-drive the connection under the
following conditions:

 - NVMe command error

 - On PRLO + N2N (rida format 2)

Link: https://lore.kernel.org/r/20210817051315.2477-11-njavali@marvell.comSigned-off-by: NQuinn Tran <qutran@marvell.com>
Signed-off-by: NNilesh Javali <njavali@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

For target port that register itself as both FCP + NVMe, initiator driver
will try to login one mode at a time. If the last mode did not succeed,
then driver will try the other mode.

When error is encountered, current code only flip to other mode one time
(NVMe->FCP) and remain on the last mode.  Driver wrongly assumed target
port does not support PRLI NVMe, instead it was not ready to receive PRLI.

This patch will alternate back and forth on every PRLI failure until login
retry count has depleted or it is succeeded.

Link: https://lore.kernel.org/r/20210817051315.2477-10-njavali@marvell.comSigned-off-by: NQuinn Tran <qutran@marvell.com>
Signed-off-by: NNilesh Javali <njavali@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The abort callback gets called only when it gets posted to firmware. The
refcounting is done properly in the callback. On internal errors, the
callback is not invoked leading to a hung I/O. Fix this by having separate
error code when command gets returned from firmware.

Link: https://lore.kernel.org/r/20210817051315.2477-9-njavali@marvell.comSigned-off-by: NArun Easi <aeasi@marvell.com>
Signed-off-by: NNilesh Javali <njavali@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Currently driver saves the personality type (FCP|NVMe) at the start of
first discovery of the remote device. If the remote device personality do
change over time, then qla driver needs to present that to user to decide.

Link: https://lore.kernel.org/r/20210817051315.2477-8-njavali@marvell.comSigned-off-by: NQuinn Tran <qutran@marvell.com>
Signed-off-by: NNilesh Javali <njavali@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

For initiator mode, always do secure login when authentication app started.
Also remove redundant flags to indicate secure connection.

Link: https://lore.kernel.org/r/20210817051315.2477-7-njavali@marvell.comSigned-off-by: NQuinn Tran <qutran@marvell.com>
Signed-off-by: NNilesh Javali <njavali@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

For EDIF + N2N to work, firmware 9.8 or later is required. The driver will
pause after PLOGI to allow app to authenticate. Once authentication
completes, app will tell driver to do PRLI.

Link: https://lore.kernel.org/r/20210817051315.2477-6-njavali@marvell.comSigned-off-by: NQuinn Tran <qutran@marvell.com>
Signed-off-by: NNilesh Javali <njavali@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The following hung task call trace was seen:

    [ 1230.183294] INFO: task qla2xxx_wq:523 blocked for more than 120 seconds.
    [ 1230.197749] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
    [ 1230.205585] qla2xxx_wq      D    0   523      2 0x80004000
    [ 1230.205636] Workqueue: qla2xxx_wq qlt_free_session_done [qla2xxx]
    [ 1230.205639] Call Trace:
    [ 1230.208100]  __schedule+0x2c4/0x700
    [ 1230.211607]  schedule+0x38/0xa0
    [ 1230.214769]  schedule_timeout+0x246/0x2f0
    [ 1230.222651]  wait_for_completion+0x97/0x100
    [ 1230.226921]  qlt_free_session_done+0x6a0/0x6f0 [qla2xxx]
    [ 1230.232254]  process_one_work+0x1a7/0x360

...when device side port resets were done.

Abort threads were getting out without processing due to the "deleted"
flag check. The delete thread, meanwhile, could not proceed with a
logout (that would have cleared out pending requests) as the logout IOCB
work was not progressing. It appears like the hung qlt_free_session_done()
thread is causing the ha->wq works on hold. The qlt_free_session_done()
was hung waiting for nvme_fc_unregister_remoteport() + localport_delete cb
to be complete, which would only happen when all I/Os are released.

Fix this by allowing abort to progress until device delete is completely
done. This should make the qlt_free_session_done() proceed without hang and
thus clear up the deadlock.

Link: https://lore.kernel.org/r/20210817051315.2477-5-njavali@marvell.comSigned-off-by: NArun Easi <aeasi@marvell.com>
Signed-off-by: NNilesh Javali <njavali@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

edif_enabled is prematurely turned on if hardware is capable of handling
the feature.  However, firmware also needs to support EDIF before enabling
this bit.

Link: https://lore.kernel.org/r/20210817051315.2477-4-njavali@marvell.comSigned-off-by: NQuinn Tran <qutran@marvell.com>
Signed-off-by: NNilesh Javali <njavali@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Reject inflight AUTH ELS if driver is going through session recovery.

Link: https://lore.kernel.org/r/20210817051315.2477-3-njavali@marvell.comSigned-off-by: NQuinn Tran <qutran@marvell.com>
Signed-off-by: NNilesh Javali <njavali@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When firmware indicates session has been torn down via UPDATE SA IOCB or
ELS Passthrough IOCB, the driver needs to also tear down the session.

Link: https://lore.kernel.org/r/20210817051315.2477-2-njavali@marvell.comSigned-off-by: NQuinn Tran <qutran@marvell.com>
Signed-off-by: NNilesh Javali <njavali@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The sd_spinup_disk() function logs what is happening. Unfortunately this
output stops if the media was marked as removed in the meantime. Add a
print for this case too.

Link: https://lore.kernel.org/r/CWXP265MB26803209FD08A64222EEEA02C4FD9@CWXP265MB2680.GBRP265.PROD.OUTLOOK.COMReviewed-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NChristian Loehle <cloehle@hyperstone.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The initial device scan might take some time, and there really is no need
to wait for it during probe().  So return immediately from scsi_scan_host()
during probe() and avoid any udev stalls during booting.

Link: https://lore.kernel.org/r/20210817075306.11315-1-mwilck@suse.comAcked-by: NTyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin Wilck <mwilck@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

TCM fails to pass the following tests in libiscsi:

  SCSI.ExtendedCopy.DescrType
  SCSI.ExtendedCopy.DescrLimits
  SCSI.ExtendedCopy.ParamHdr
  SCSI.ExtendedCopy.ValidSegDescr
  SCSI.ExtendedCopy.ValidTgtDescr

The xcopy code always returns the same NOT READY sense key for all detected
errors. Change the sense key for invalid requests to ILLEGAL REQUEST, and
for aborted transfers to COPY ABORTED.

Link: https://lore.kernel.org/r/20210803145410.80147-3-s.samoylenko@yadro.com
Fixes: d877d727 ("target: Fix a deadlock between the XCOPY code and iSCSI session shutdown")
Reviewed-by: NDavid Disseldorp <ddiss@suse.de>
Reviewed-by: NRoman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: NKonstantin Shelekhin <k.shelekhin@yadro.com>
Signed-off-by: NSergey Samoylenko <s.samoylenko@yadro.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Currently, backend drivers can fail I/O with SAM_STAT_CHECK_CONDITION which
gets us TCM_LOGICAL_UNIT_COMMUNICATION_FAILURE.

Add a new helper that allows backend drivers to fail with specific sense
codes.

This is based on a patch from Mike Christie <michael.christie@oracle.com>.

Cc: Mike Christie <michael.christie@oracle.com>
Link: https://lore.kernel.org/r/20210803145410.80147-2-s.samoylenko@yadro.comReviewed-by: NDavid Disseldorp <ddiss@suse.de>
Signed-off-by: NSergey Samoylenko <s.samoylenko@yadro.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

There is a regular need in the kernel to provide a way to declare having a
dynamically sized set of trailing elements in a structure. Kernel code
should always use "flexible array members"[1] for these cases. The older
style of one-element or zero-length arrays should no longer be used[2].

Refactor the code a bit according to the use of a flexible-array member in
struct pqi_event_config instead of a one-element array, and use the
struct_size() helper.

This helps with the ongoing efforts to globally enable -Warray-bounds and
get us closer to being able to tighten the FORTIFY_SOURCE routines on
memcpy().

This issue was found with the help of Coccinelle and audited and fixed,
manually.

[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.10/process/deprecated.html#zero-length-and-one-element-arrays

Link: https://github.com/KSPP/linux/issues/79
Link: https://github.com/KSPP/linux/issues/109
Link: https://lore.kernel.org/r/20210810210741.GA58765@embeddedorSigned-off-by: NGustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The return value of transport_kmap_data_sg() is assigned to the variable
buf:

  buf = transport_kmap_data_sg(cmd);

And then it is checked:

  if (!buf) {

This indicates that buf can be NULL. However, it is dereferenced in the
following statements:

  if (!(buf[3] & 0x80))
    buf[3] |= 0x80;
  if (!(buf[2] & 0x80))
    buf[2] |= 0x80;

To fix these possible null-pointer dereferences, dereference buf and call
transport_kunmap_data_sg() only when buf is not NULL.

Link: https://lore.kernel.org/r/20210810040414.248167-1-islituo@gmail.comReported-by: NTOTE Robot <oslab@tsinghua.edu.cn>
Reviewed-by: NBodo Stroesser <bostroesser@gmail.com>
Signed-off-by: NTuo Li <islituo@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>