By using this mechanism we can get rid of the not so nice method of
scheduling TX NAPI when the RX was scheduled. No bandwidth reduction was
seen with this change.

Changes from v1:
- Remove useless comment (Jakub)
- Do not bind the TX clean to NAPI budget (Jakub)
Signed-off-by: NJose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DMA Capabilites have grown but the DebugFS that shows this info has not
been updated. Lets add the missing information.
Signed-off-by: NJose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the hardware TID index is assumed to start from index 0.
However, with the following changeset,

commit c2193999 ("cxgb4: add support for high priority filters")

hardware TID index can start after the high priority region, which
has introduced a regression resulting in connection failures for
ULDs.

So, fix all related code to properly recalculate the TID start index
based on whether high priority filters are enabled or not.

Fixes: c2193999 ("cxgb4: add support for high priority filters")
Signed-off-by: NShahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit c2193999 ("cxgb4: add support for high priority filters")
has missed considering high priority region calculation in some code
paths. This patch fixes them.

Fixes: c2193999 ("cxgb4: add support for high priority filters")
Signed-off-by: NShahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are no clocks, resets or gpios referenced by Tegra ACPI
device so don't access clocks, resets or gpios interface with
ACPI device.

Clocks, resets and GPIOs for ACPI devices will be handled via
ACPI interface.
Signed-off-by: NAjay Gupta <ajayg@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use generic device api so that driver can work both with DT
or ACPI based devices.
Signed-off-by: NAjay Gupta <ajayg@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MT2712 SoC can provide the rmii reference clock, and the clock
will output from TXC pin only, which means ref_clk pin of external
PHY should connect to TXC pin in this case.
Add corresponding clock and timing settings.
Signed-off-by: NBiao Huang <biao.huang@mediatek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix up the mvpp2 validate implementation to adopt the same behaviour as
mvneta:
- only allow the link modes that the specified PHY interface mode
  supports with the exception of 1000base-X and 2500base-X.
- use the basex helper to deal with SFP modules that can be switched
  between 1000base-X vs 2500base-X.

This gives consistent behaviour between mvneta and mvpp2.

This commit depends on "net: phylink: extend clause 45 PHY validation
workaround" so is not marked for backporting to stable kernels.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Acked-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unlike mlxsw, the other listeners to the FIB notification chain do not
require any special modifications as they never considered multiple
identical routes.

This patch removes the old route notifications and converts all the
listeners to use the new replace / delete notifications.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the new notifications mlxsw does not need to handle identical
routes itself, as this is taken care of by the core IPv4 code.

Instead, mlxsw only needs to take care of inserting and removing routes
from the device.

Convert mlxsw to use the new IPv4 route notifications and simplify the
code.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

service_task will be scheduled  per second to do some periodic
jobs. When reset fails, it means this device is not available
now, so the periodic jobs do not need to be handled.

This patch adds flag HCLGE_STATE_RST_FAIL/HCLGEVF_STATE_RST_FAIL
to indicate that reset fails, and checks this flag before
schedule periodic task.
Signed-off-by: NGuojia Liao <liaoguojia@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The hns3 driver may be used in memory reclaim path when it
is the low level transport of a network file system, so it
needs to guarantee forward progress even under memory pressure.

This patch allocates a private WQ with WQ_MEM_RECLAIM set for
both hclge_main and hclgevf_main modules.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are four work (mbx_service_task, service_task,
rst_service_task and keep_alive_task)in the hclgevf module,
mbx_service_task is for handling mailbox issue, service_task is
for periodic management issue and rst_service_task is for reset
related issue, keep_alive_task is used to keepalive between PF
and VF, which can be done in a single work.

This patch removes the mbx_service_task, rst_service_task and
keep_alive_task, and moves the related handling to the
service_task work in order to remove concurrency between the four
work and to improve efficiency.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are three work (mbx_service_task, service_task,
rst_service_task) in the HNS3 driver, mbx_service_task is for
handling mailbox work, service_task is for periodic management
issue and rst_service_task is for reset related issue, which can
be handled in a single work.

This patch removes the mbx_service_task and rst_service_task
work, and moves the related handling to the service_task work
in order to remove concurrency between the three work and to
improve efficiency.

BTW, since stats_timer in struct hclge_hw_stats is not needed
anymore, so removes the definition of struct hclge_hw_stats,
and moves mac_stats into struct hclge_dev.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, a timer is defined to schedule hclgevf_service per
second. To simplify the code, this patch uses the delayed work
instead of timer to schedule hclgevf_serive.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some users complained about problems with r8169 and it turned out that
the generic PHY driver was used instead instead of the dedicated one.
In all cases reason was that r8169.ko was in initramfs, but realtek.ko
not. Manually adding realtek.ko to initramfs fixed the issues.
Root cause seems to be that tools like dracut and genkernel don't
consider softdeps. Add a check for loaded Realtek PHY driver module
and provide the user with a hint if it's not loaded.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is to add external trigger event support
for dpaa2-ptp driver with v2 dprtc_set_irq_mask() API.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 78beef62 ("nfp: abm: fix memory leak in
nfp_abm_u32_knode_replace").

The quoted commit does not fix anything and resulted in a bogus
CVE-2019-19076.

If match is NULL then it is known there is no matching entry in
list, hence, calling nfp_abm_u32_knode_delete() is pointless.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NJohn Hurley <john.hurley@netronome.com>

Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This allows incrementing the correct timeout statistic without any mess.
Down the road, devices can learn to reset just the specific queue.

The patch was generated with the following script:

use strict;
use warnings;

our $^I = '.bak';

my @work = (
["arch/m68k/emu/nfeth.c", "nfeth_tx_timeout"],
["arch/um/drivers/net_kern.c", "uml_net_tx_timeout"],
["arch/um/drivers/vector_kern.c", "vector_net_tx_timeout"],
["arch/xtensa/platforms/iss/network.c", "iss_net_tx_timeout"],
["drivers/char/pcmcia/synclink_cs.c", "hdlcdev_tx_timeout"],
["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"],
["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"],
["drivers/message/fusion/mptlan.c", "mpt_lan_tx_timeout"],
["drivers/misc/sgi-xp/xpnet.c", "xpnet_dev_tx_timeout"],
["drivers/net/appletalk/cops.c", "cops_timeout"],
["drivers/net/arcnet/arcdevice.h", "arcnet_timeout"],
["drivers/net/arcnet/arcnet.c", "arcnet_timeout"],
["drivers/net/arcnet/com20020.c", "arcnet_timeout"],
["drivers/net/ethernet/3com/3c509.c", "el3_tx_timeout"],
["drivers/net/ethernet/3com/3c515.c", "corkscrew_timeout"],
["drivers/net/ethernet/3com/3c574_cs.c", "el3_tx_timeout"],
["drivers/net/ethernet/3com/3c589_cs.c", "el3_tx_timeout"],
["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"],
["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"],
["drivers/net/ethernet/3com/typhoon.c", "typhoon_tx_timeout"],
["drivers/net/ethernet/8390/8390.h", "ei_tx_timeout"],
["drivers/net/ethernet/8390/8390.h", "eip_tx_timeout"],
["drivers/net/ethernet/8390/8390.c", "ei_tx_timeout"],
["drivers/net/ethernet/8390/8390p.c", "eip_tx_timeout"],
["drivers/net/ethernet/8390/ax88796.c", "ax_ei_tx_timeout"],
["drivers/net/ethernet/8390/axnet_cs.c", "axnet_tx_timeout"],
["drivers/net/ethernet/8390/etherh.c", "__ei_tx_timeout"],
["drivers/net/ethernet/8390/hydra.c", "__ei_tx_timeout"],
["drivers/net/ethernet/8390/mac8390.c", "__ei_tx_timeout"],
["drivers/net/ethernet/8390/mcf8390.c", "__ei_tx_timeout"],
["drivers/net/ethernet/8390/lib8390.c", "__ei_tx_timeout"],
["drivers/net/ethernet/8390/ne2k-pci.c", "ei_tx_timeout"],
["drivers/net/ethernet/8390/pcnet_cs.c", "ei_tx_timeout"],
["drivers/net/ethernet/8390/smc-ultra.c", "ei_tx_timeout"],
["drivers/net/ethernet/8390/wd.c", "ei_tx_timeout"],
["drivers/net/ethernet/8390/zorro8390.c", "__ei_tx_timeout"],
["drivers/net/ethernet/adaptec/starfire.c", "tx_timeout"],
["drivers/net/ethernet/agere/et131x.c", "et131x_tx_timeout"],
["drivers/net/ethernet/allwinner/sun4i-emac.c", "emac_timeout"],
["drivers/net/ethernet/alteon/acenic.c", "ace_watchdog"],
["drivers/net/ethernet/amazon/ena/ena_netdev.c", "ena_tx_timeout"],
["drivers/net/ethernet/amd/7990.h", "lance_tx_timeout"],
["drivers/net/ethernet/amd/7990.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/a2065.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/am79c961a.c", "am79c961_timeout"],
["drivers/net/ethernet/amd/amd8111e.c", "amd8111e_tx_timeout"],
["drivers/net/ethernet/amd/ariadne.c", "ariadne_tx_timeout"],
["drivers/net/ethernet/amd/atarilance.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/au1000_eth.c", "au1000_tx_timeout"],
["drivers/net/ethernet/amd/declance.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/lance.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/mvme147.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/ni65.c", "ni65_timeout"],
["drivers/net/ethernet/amd/nmclan_cs.c", "mace_tx_timeout"],
["drivers/net/ethernet/amd/pcnet32.c", "pcnet32_tx_timeout"],
["drivers/net/ethernet/amd/sunlance.c", "lance_tx_timeout"],
["drivers/net/ethernet/amd/xgbe/xgbe-drv.c", "xgbe_tx_timeout"],
["drivers/net/ethernet/apm/xgene-v2/main.c", "xge_timeout"],
["drivers/net/ethernet/apm/xgene/xgene_enet_main.c", "xgene_enet_timeout"],
["drivers/net/ethernet/apple/macmace.c", "mace_tx_timeout"],
["drivers/net/ethernet/atheros/ag71xx.c", "ag71xx_tx_timeout"],
["drivers/net/ethernet/atheros/alx/main.c", "alx_tx_timeout"],
["drivers/net/ethernet/atheros/atl1c/atl1c_main.c", "atl1c_tx_timeout"],
["drivers/net/ethernet/atheros/atl1e/atl1e_main.c", "atl1e_tx_timeout"],
["drivers/net/ethernet/atheros/atlx/atl.c", "atlx_tx_timeout"],
["drivers/net/ethernet/atheros/atlx/atl1.c", "atlx_tx_timeout"],
["drivers/net/ethernet/atheros/atlx/atl2.c", "atl2_tx_timeout"],
["drivers/net/ethernet/broadcom/b44.c", "b44_tx_timeout"],
["drivers/net/ethernet/broadcom/bcmsysport.c", "bcm_sysport_tx_timeout"],
["drivers/net/ethernet/broadcom/bnx2.c", "bnx2_tx_timeout"],
["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h", "bnx2x_tx_timeout"],
["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c", "bnx2x_tx_timeout"],
["drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c", "bnx2x_tx_timeout"],
["drivers/net/ethernet/broadcom/bnxt/bnxt.c", "bnxt_tx_timeout"],
["drivers/net/ethernet/broadcom/genet/bcmgenet.c", "bcmgenet_timeout"],
["drivers/net/ethernet/broadcom/sb1250-mac.c", "sbmac_tx_timeout"],
["drivers/net/ethernet/broadcom/tg3.c", "tg3_tx_timeout"],
["drivers/net/ethernet/calxeda/xgmac.c", "xgmac_tx_timeout"],
["drivers/net/ethernet/cavium/liquidio/lio_main.c", "liquidio_tx_timeout"],
["drivers/net/ethernet/cavium/liquidio/lio_vf_main.c", "liquidio_tx_timeout"],
["drivers/net/ethernet/cavium/liquidio/lio_vf_rep.c", "lio_vf_rep_tx_timeout"],
["drivers/net/ethernet/cavium/thunder/nicvf_main.c", "nicvf_tx_timeout"],
["drivers/net/ethernet/cirrus/cs89x0.c", "net_timeout"],
["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"],
["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"],
["drivers/net/ethernet/cortina/gemini.c", "gmac_tx_timeout"],
["drivers/net/ethernet/davicom/dm9000.c", "dm9000_timeout"],
["drivers/net/ethernet/dec/tulip/de2104x.c", "de_tx_timeout"],
["drivers/net/ethernet/dec/tulip/tulip_core.c", "tulip_tx_timeout"],
["drivers/net/ethernet/dec/tulip/winbond-840.c", "tx_timeout"],
["drivers/net/ethernet/dlink/dl2k.c", "rio_tx_timeout"],
["drivers/net/ethernet/dlink/sundance.c", "tx_timeout"],
["drivers/net/ethernet/emulex/benet/be_main.c", "be_tx_timeout"],
["drivers/net/ethernet/ethoc.c", "ethoc_tx_timeout"],
["drivers/net/ethernet/faraday/ftgmac100.c", "ftgmac100_tx_timeout"],
["drivers/net/ethernet/fealnx.c", "fealnx_tx_timeout"],
["drivers/net/ethernet/freescale/dpaa/dpaa_eth.c", "dpaa_tx_timeout"],
["drivers/net/ethernet/freescale/fec_main.c", "fec_timeout"],
["drivers/net/ethernet/freescale/fec_mpc52xx.c", "mpc52xx_fec_tx_timeout"],
["drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c", "fs_timeout"],
["drivers/net/ethernet/freescale/gianfar.c", "gfar_timeout"],
["drivers/net/ethernet/freescale/ucc_geth.c", "ucc_geth_timeout"],
["drivers/net/ethernet/fujitsu/fmvj18x_cs.c", "fjn_tx_timeout"],
["drivers/net/ethernet/google/gve/gve_main.c", "gve_tx_timeout"],
["drivers/net/ethernet/hisilicon/hip04_eth.c", "hip04_timeout"],
["drivers/net/ethernet/hisilicon/hix5hd2_gmac.c", "hix5hd2_net_timeout"],
["drivers/net/ethernet/hisilicon/hns/hns_enet.c", "hns_nic_net_timeout"],
["drivers/net/ethernet/hisilicon/hns3/hns3_enet.c", "hns3_nic_net_timeout"],
["drivers/net/ethernet/huawei/hinic/hinic_main.c", "hinic_tx_timeout"],
["drivers/net/ethernet/i825xx/82596.c", "i596_tx_timeout"],
["drivers/net/ethernet/i825xx/ether1.c", "ether1_timeout"],
["drivers/net/ethernet/i825xx/lib82596.c", "i596_tx_timeout"],
["drivers/net/ethernet/i825xx/sun3_82586.c", "sun3_82586_timeout"],
["drivers/net/ethernet/ibm/ehea/ehea_main.c", "ehea_tx_watchdog"],
["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"],
["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"],
["drivers/net/ethernet/ibm/ibmvnic.c", "ibmvnic_tx_timeout"],
["drivers/net/ethernet/intel/e100.c", "e100_tx_timeout"],
["drivers/net/ethernet/intel/e1000/e1000_main.c", "e1000_tx_timeout"],
["drivers/net/ethernet/intel/e1000e/netdev.c", "e1000_tx_timeout"],
["drivers/net/ethernet/intel/fm10k/fm10k_netdev.c", "fm10k_tx_timeout"],
["drivers/net/ethernet/intel/i40e/i40e_main.c", "i40e_tx_timeout"],
["drivers/net/ethernet/intel/iavf/iavf_main.c", "iavf_tx_timeout"],
["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"],
["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"],
["drivers/net/ethernet/intel/igb/igb_main.c", "igb_tx_timeout"],
["drivers/net/ethernet/intel/igbvf/netdev.c", "igbvf_tx_timeout"],
["drivers/net/ethernet/intel/ixgb/ixgb_main.c", "ixgb_tx_timeout"],
["drivers/net/ethernet/intel/ixgbe/ixgbe_debugfs.c", "adapter->netdev->netdev_ops->ndo_tx_timeout(adapter->netdev);"],
["drivers/net/ethernet/intel/ixgbe/ixgbe_main.c", "ixgbe_tx_timeout"],
["drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c", "ixgbevf_tx_timeout"],
["drivers/net/ethernet/jme.c", "jme_tx_timeout"],
["drivers/net/ethernet/korina.c", "korina_tx_timeout"],
["drivers/net/ethernet/lantiq_etop.c", "ltq_etop_tx_timeout"],
["drivers/net/ethernet/marvell/mv643xx_eth.c", "mv643xx_eth_tx_timeout"],
["drivers/net/ethernet/marvell/pxa168_eth.c", "pxa168_eth_tx_timeout"],
["drivers/net/ethernet/marvell/skge.c", "skge_tx_timeout"],
["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"],
["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"],
["drivers/net/ethernet/mediatek/mtk_eth_soc.c", "mtk_tx_timeout"],
["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"],
["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"],
["drivers/net/ethernet/mellanox/mlx5/core/en_main.c", "mlx5e_tx_timeout"],
["drivers/net/ethernet/micrel/ks8842.c", "ks8842_tx_timeout"],
["drivers/net/ethernet/micrel/ksz884x.c", "netdev_tx_timeout"],
["drivers/net/ethernet/microchip/enc28j60.c", "enc28j60_tx_timeout"],
["drivers/net/ethernet/microchip/encx24j600.c", "encx24j600_tx_timeout"],
["drivers/net/ethernet/natsemi/sonic.h", "sonic_tx_timeout"],
["drivers/net/ethernet/natsemi/sonic.c", "sonic_tx_timeout"],
["drivers/net/ethernet/natsemi/jazzsonic.c", "sonic_tx_timeout"],
["drivers/net/ethernet/natsemi/macsonic.c", "sonic_tx_timeout"],
["drivers/net/ethernet/natsemi/natsemi.c", "ns_tx_timeout"],
["drivers/net/ethernet/natsemi/ns83820.c", "ns83820_tx_timeout"],
["drivers/net/ethernet/natsemi/xtsonic.c", "sonic_tx_timeout"],
["drivers/net/ethernet/neterion/s2io.h", "s2io_tx_watchdog"],
["drivers/net/ethernet/neterion/s2io.c", "s2io_tx_watchdog"],
["drivers/net/ethernet/neterion/vxge/vxge-main.c", "vxge_tx_watchdog"],
["drivers/net/ethernet/netronome/nfp/nfp_net_common.c", "nfp_net_tx_timeout"],
["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"],
["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"],
["drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c", "pch_gbe_tx_timeout"],
["drivers/net/ethernet/packetengines/hamachi.c", "hamachi_tx_timeout"],
["drivers/net/ethernet/packetengines/yellowfin.c", "yellowfin_tx_timeout"],
["drivers/net/ethernet/pensando/ionic/ionic_lif.c", "ionic_tx_timeout"],
["drivers/net/ethernet/qlogic/netxen/netxen_nic_main.c", "netxen_tx_timeout"],
["drivers/net/ethernet/qlogic/qla3xxx.c", "ql3xxx_tx_timeout"],
["drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c", "qlcnic_tx_timeout"],
["drivers/net/ethernet/qualcomm/emac/emac.c", "emac_tx_timeout"],
["drivers/net/ethernet/qualcomm/qca_spi.c", "qcaspi_netdev_tx_timeout"],
["drivers/net/ethernet/qualcomm/qca_uart.c", "qcauart_netdev_tx_timeout"],
["drivers/net/ethernet/rdc/r6040.c", "r6040_tx_timeout"],
["drivers/net/ethernet/realtek/8139cp.c", "cp_tx_timeout"],
["drivers/net/ethernet/realtek/8139too.c", "rtl8139_tx_timeout"],
["drivers/net/ethernet/realtek/atp.c", "tx_timeout"],
["drivers/net/ethernet/realtek/r8169_main.c", "rtl8169_tx_timeout"],
["drivers/net/ethernet/renesas/ravb_main.c", "ravb_tx_timeout"],
["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"],
["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"],
["drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c", "sxgbe_tx_timeout"],
["drivers/net/ethernet/seeq/ether3.c", "ether3_timeout"],
["drivers/net/ethernet/seeq/sgiseeq.c", "timeout"],
["drivers/net/ethernet/sfc/efx.c", "efx_watchdog"],
["drivers/net/ethernet/sfc/falcon/efx.c", "ef4_watchdog"],
["drivers/net/ethernet/sgi/ioc3-eth.c", "ioc3_timeout"],
["drivers/net/ethernet/sgi/meth.c", "meth_tx_timeout"],
["drivers/net/ethernet/silan/sc92031.c", "sc92031_tx_timeout"],
["drivers/net/ethernet/sis/sis190.c", "sis190_tx_timeout"],
["drivers/net/ethernet/sis/sis900.c", "sis900_tx_timeout"],
["drivers/net/ethernet/smsc/epic100.c", "epic_tx_timeout"],
["drivers/net/ethernet/smsc/smc911x.c", "smc911x_timeout"],
["drivers/net/ethernet/smsc/smc9194.c", "smc_timeout"],
["drivers/net/ethernet/smsc/smc91c92_cs.c", "smc_tx_timeout"],
["drivers/net/ethernet/smsc/smc91x.c", "smc_timeout"],
["drivers/net/ethernet/stmicro/stmmac/stmmac_main.c", "stmmac_tx_timeout"],
["drivers/net/ethernet/sun/cassini.c", "cas_tx_timeout"],
["drivers/net/ethernet/sun/ldmvsw.c", "sunvnet_tx_timeout_common"],
["drivers/net/ethernet/sun/niu.c", "niu_tx_timeout"],
["drivers/net/ethernet/sun/sunbmac.c", "bigmac_tx_timeout"],
["drivers/net/ethernet/sun/sungem.c", "gem_tx_timeout"],
["drivers/net/ethernet/sun/sunhme.c", "happy_meal_tx_timeout"],
["drivers/net/ethernet/sun/sunqe.c", "qe_tx_timeout"],
["drivers/net/ethernet/sun/sunvnet.c", "sunvnet_tx_timeout_common"],
["drivers/net/ethernet/sun/sunvnet_common.c", "sunvnet_tx_timeout_common"],
["drivers/net/ethernet/sun/sunvnet_common.h", "sunvnet_tx_timeout_common"],
["drivers/net/ethernet/synopsys/dwc-xlgmac-net.c", "xlgmac_tx_timeout"],
["drivers/net/ethernet/ti/cpmac.c", "cpmac_tx_timeout"],
["drivers/net/ethernet/ti/cpsw.c", "cpsw_ndo_tx_timeout"],
["drivers/net/ethernet/ti/cpsw_priv.c", "cpsw_ndo_tx_timeout"],
["drivers/net/ethernet/ti/cpsw_priv.h", "cpsw_ndo_tx_timeout"],
["drivers/net/ethernet/ti/davinci_emac.c", "emac_dev_tx_timeout"],
["drivers/net/ethernet/ti/netcp_core.c", "netcp_ndo_tx_timeout"],
["drivers/net/ethernet/ti/tlan.c", "tlan_tx_timeout"],
["drivers/net/ethernet/toshiba/ps3_gelic_net.h", "gelic_net_tx_timeout"],
["drivers/net/ethernet/toshiba/ps3_gelic_net.c", "gelic_net_tx_timeout"],
["drivers/net/ethernet/toshiba/ps3_gelic_wireless.c", "gelic_net_tx_timeout"],
["drivers/net/ethernet/toshiba/spider_net.c", "spider_net_tx_timeout"],
["drivers/net/ethernet/toshiba/tc35815.c", "tc35815_tx_timeout"],
["drivers/net/ethernet/via/via-rhine.c", "rhine_tx_timeout"],
["drivers/net/ethernet/wiznet/w5100.c", "w5100_tx_timeout"],
["drivers/net/ethernet/wiznet/w5300.c", "w5300_tx_timeout"],
["drivers/net/ethernet/xilinx/xilinx_emaclite.c", "xemaclite_tx_timeout"],
["drivers/net/ethernet/xircom/xirc2ps_cs.c", "xirc_tx_timeout"],
["drivers/net/fjes/fjes_main.c", "fjes_tx_retry"],
["drivers/net/slip/slip.c", "sl_tx_timeout"],
["include/linux/usb/usbnet.h", "usbnet_tx_timeout"],
["drivers/net/usb/aqc111.c", "usbnet_tx_timeout"],
["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"],
["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"],
["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"],
["drivers/net/usb/ax88172a.c", "usbnet_tx_timeout"],
["drivers/net/usb/ax88179_178a.c", "usbnet_tx_timeout"],
["drivers/net/usb/catc.c", "catc_tx_timeout"],
["drivers/net/usb/cdc_mbim.c", "usbnet_tx_timeout"],
["drivers/net/usb/cdc_ncm.c", "usbnet_tx_timeout"],
["drivers/net/usb/dm9601.c", "usbnet_tx_timeout"],
["drivers/net/usb/hso.c", "hso_net_tx_timeout"],
["drivers/net/usb/int51x1.c", "usbnet_tx_timeout"],
["drivers/net/usb/ipheth.c", "ipheth_tx_timeout"],
["drivers/net/usb/kaweth.c", "kaweth_tx_timeout"],
["drivers/net/usb/lan78xx.c", "lan78xx_tx_timeout"],
["drivers/net/usb/mcs7830.c", "usbnet_tx_timeout"],
["drivers/net/usb/pegasus.c", "pegasus_tx_timeout"],
["drivers/net/usb/qmi_wwan.c", "usbnet_tx_timeout"],
["drivers/net/usb/r8152.c", "rtl8152_tx_timeout"],
["drivers/net/usb/rndis_host.c", "usbnet_tx_timeout"],
["drivers/net/usb/rtl8150.c", "rtl8150_tx_timeout"],
["drivers/net/usb/sierra_net.c", "usbnet_tx_timeout"],
["drivers/net/usb/smsc75xx.c", "usbnet_tx_timeout"],
["drivers/net/usb/smsc95xx.c", "usbnet_tx_timeout"],
["drivers/net/usb/sr9700.c", "usbnet_tx_timeout"],
["drivers/net/usb/sr9800.c", "usbnet_tx_timeout"],
["drivers/net/usb/usbnet.c", "usbnet_tx_timeout"],
["drivers/net/vmxnet3/vmxnet3_drv.c", "vmxnet3_tx_timeout"],
["drivers/net/wan/cosa.c", "cosa_net_timeout"],
["drivers/net/wan/farsync.c", "fst_tx_timeout"],
["drivers/net/wan/fsl_ucc_hdlc.c", "uhdlc_tx_timeout"],
["drivers/net/wan/lmc/lmc_main.c", "lmc_driver_timeout"],
["drivers/net/wan/x25_asy.c", "x25_asy_timeout"],
["drivers/net/wimax/i2400m/netdev.c", "i2400m_tx_timeout"],
["drivers/net/wireless/intel/ipw2x00/ipw2100.c", "ipw2100_tx_timeout"],
["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"],
["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"],
["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"],
["drivers/net/wireless/intersil/orinoco/main.c", "orinoco_tx_timeout"],
["drivers/net/wireless/intersil/orinoco/orinoco_usb.c", "orinoco_tx_timeout"],
["drivers/net/wireless/intersil/orinoco/orinoco.h", "orinoco_tx_timeout"],
["drivers/net/wireless/intersil/prism54/islpci_dev.c", "islpci_eth_tx_timeout"],
["drivers/net/wireless/intersil/prism54/islpci_eth.c", "islpci_eth_tx_timeout"],
["drivers/net/wireless/intersil/prism54/islpci_eth.h", "islpci_eth_tx_timeout"],
["drivers/net/wireless/marvell/mwifiex/main.c", "mwifiex_tx_timeout"],
["drivers/net/wireless/quantenna/qtnfmac/core.c", "qtnf_netdev_tx_timeout"],
["drivers/net/wireless/quantenna/qtnfmac/core.h", "qtnf_netdev_tx_timeout"],
["drivers/net/wireless/rndis_wlan.c", "usbnet_tx_timeout"],
["drivers/net/wireless/wl3501_cs.c", "wl3501_tx_timeout"],
["drivers/net/wireless/zydas/zd1201.c", "zd1201_tx_timeout"],
["drivers/s390/net/qeth_core.h", "qeth_tx_timeout"],
["drivers/s390/net/qeth_core_main.c", "qeth_tx_timeout"],
["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"],
["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"],
["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"],
["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"],
["drivers/staging/ks7010/ks_wlan_net.c", "ks_wlan_tx_timeout"],
["drivers/staging/qlge/qlge_main.c", "qlge_tx_timeout"],
["drivers/staging/rtl8192e/rtl8192e/rtl_core.c", "_rtl92e_tx_timeout"],
["drivers/staging/rtl8192u/r8192U_core.c", "tx_timeout"],
["drivers/staging/unisys/visornic/visornic_main.c", "visornic_xmit_timeout"],
["drivers/staging/wlan-ng/p80211netdev.c", "p80211knetdev_tx_timeout"],
["drivers/tty/n_gsm.c", "gsm_mux_net_tx_timeout"],
["drivers/tty/synclink.c", "hdlcdev_tx_timeout"],
["drivers/tty/synclink_gt.c", "hdlcdev_tx_timeout"],
["drivers/tty/synclinkmp.c", "hdlcdev_tx_timeout"],
["net/atm/lec.c", "lec_tx_timeout"],
["net/bluetooth/bnep/netdev.c", "bnep_net_timeout"]
);

for my $p (@work) {
	my @pair = @$p;
	my $file = $pair[0];
	my $func = $pair[1];
	print STDERR $file , ": ", $func,"\n";
	our @ARGV = ($file);
	while (<ARGV>) {
		if (m/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/) {
			print STDERR "found $1+$2 in $file\n";
		}
		if (s/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/$1, unsigned int txqueue$2/) {
			print STDERR "$func found in $file\n";
		}
		print;
	}
}

where the list of files and functions is simply from:

git grep ndo_tx_timeout, with manual addition of headers
in the rare cases where the function is from a header,
then manually changing the few places which actually
call ndo_tx_timeout.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Acked-by: NHeiner Kallweit <hkallweit1@gmail.com>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: NShannon Nelson <snelson@pensando.io>
Reviewed-by: NMartin Habets <mhabets@solarflare.com>

changes from v9:
	fixup a forward declaration
changes from v9:
	more leftovers from v3 change
changes from v8:
        fix up a missing direct call to timeout
        rebased on net-next
changes from v7:
	fixup leftovers from v3 change
changes from v6:
	fix typo in rtl driver
changes from v5:
	add missing files (allow any net device argument name)
changes from v4:
	add a missing driver header
changes from v3:
        change queue # to unsigned
Changes from v2:
        added headers
Changes from v1:
        Fix errors found by kbuild:
        generalize the pattern a bit, to pick up
        a couple of instances missed by the previous
        version.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The first_interrupt field is accessed in ena_intr_msix_io() upon
receiving an interrupt.The rx_ring and tx_ring fields of napi can
be NULL when receiving interrupt for xdp queues. This patch fixes
the issue by moving the field to the ena_napi struct.
Signed-off-by: NSameeh Jubran <sameehj@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit implements the XDP_TX action in the ena driver. We allocate
separate tx queues for the XDP_TX. We currently allow xdp only when
there is enough queues to allocate for xdp.
Signed-off-by: NSameeh Jubran <sameehj@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit implements the basic functionality of drop/pass logic in the
ena driver.
Signed-off-by: NSameeh Jubran <sameehj@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

T6 has a separate region known as high priority filter region
that allows classifying packets going through ULD path. So,
query firmware for HPFILTER resources and enable the high
priority offload filter support when it is available.
Signed-off-by: NShahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/freescale/enetc/enetc_qos.c: In function enetc_setup_tc_cbs:
drivers/net/ethernet/freescale/enetc/enetc_qos.c:195:6: warning: variable tc_max_sized_frame set but not used [-Wunused-but-set-variable]

Fixes: c431047c ("enetc: add support Credit Based Shaper(CBS) for hardware offload")
Signed-off-by: NChen Wandun <chenwandun@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Device stats are currently hard coded in the PCI BAR0 layout.
Add a ability to read them from the TLV area instead.
Names for the stats are maintained by the driver, and their
meaning documented. This allows us to more easily add and
remove device stats.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Provide a software TX timestamp and add it to the ethtool query
interface.

skb_tx_timestamp() is also needed if one would like to use PHY
timestamping.
Signed-off-by: NMichael Walle <michael@walle.cc>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clang warns:

../drivers/net/ethernet/smsc/smc911x.c:939:3: warning: misleading
indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
         if (!lp->ctl_rfduplx)
         ^
../drivers/net/ethernet/smsc/smc911x.c:936:2: note: previous statement
is here
        if (lp->ctl_rspeed != 100)
        ^
1 warning generated.

This warning occurs because there is a space after the tab on this line.
Remove it so that the indentation is consistent with the Linux kernel
coding style and clang no longer warns.

Fixes: 0a0c72c9 ("[PATCH] RE: [PATCH 1/1] net driver: Add support for SMSC LAN911x line of ethernet chips")
Link: https://github.com/ClangBuiltLinux/linux/issues/796Signed-off-by: NNathan Chancellor <natechancellor@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clang warns:

../drivers/net/ethernet/dec/tulip/uli526x.c:1812:3: warning: misleading
indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
        switch (mode) {
        ^
../drivers/net/ethernet/dec/tulip/uli526x.c:1809:2: note: previous
statement is here
        if (cr6set)
        ^
1 warning generated.

../drivers/net/ethernet/dec/tulip/dmfe.c:2217:3: warning: misleading
indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
        switch(mode) {
        ^
../drivers/net/ethernet/dec/tulip/dmfe.c:2214:2: note: previous
statement is here
        if (cr6set)
        ^
1 warning generated.

This warning occurs because there is a space before the tab on these
lines. Remove them so that the indentation is consistent with the Linux
kernel coding style and clang no longer warns.

While we are here, adjust the default block in dmfe_init_module to have
a proper break between the label and assignment and add a space between
the switch and opening parentheses to avoid a checkpatch warning.

Fixes: e1c3e501 ("[PATCH] initialisation cleanup for ULI526x-net-driver")
Link: https://github.com/ClangBuiltLinux/linux/issues/795Signed-off-by: NNathan Chancellor <natechancellor@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The variable rc is assigned with a value that is never read and
it is re-assigned a new value later on.  The assignment is redundant
and can be removed.  Clean up multiple occurrances of this pattern.

Addresses-Coverity: ("Unused value")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In referenced fix we removed the RTL8168e-specific jumbo config for
RTL8168evl in rtl_hw_jumbo_enable(). We have to do the same in
rtl_hw_jumbo_disable().

v2: fix referenced commit id

Fixes: 14012c9f ("r8169: fix jumbo configuration for RTL8168evl")
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RTL8125 also requires to enable RX for WoL.

v2: add missing Fixes tag

Fixes: f1bce4ad ("r8169: add support for RTL8125")
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now RX interrupt is triggered twice every time, because in
cpsw_rx_interrupt() it is asked first and then disabled. So there will be
pending interrupt always, when RX interrupt is enabled again in NAPI
handler.

Fix it by first disabling IRQ and then do ask.

Fixes: 870915fe ("drivers: net: cpsw: remove disable_irq/enable_irq as irq can be masked from cpsw itself")
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We may have found a bug in the nxp/lpc_eth.c driver. The function
platform_set_drvdata() is called twice, the second time it is called,
in lpc_mii_init(), it overwrites the struct net_device which should be
at pdev->dev->driver_data with pldat->mii_bus. When trying to remove
the driver, in lpc_eth_drv_remove(), platform_get_drvdata() will
return the pldat->mii_bus pointer and try to use it as a struct
net_device pointer. This causes unregister_netdev to segfault and
generate a kernel BUG. Is this reproducible?
Signed-off-by: NDaniel Martinez <linux@danielsmartinez.com>
Signed-off-by: NBruno Carneiro da Cunha <brunocarneirodacunha@usp.br>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refer to the databook of DesignWare Cores Ethernet MAC Universal:

6.2.1.5 Register 4 (Transmit Descriptor List Address Register

If this register is not changed when the ST bit is set to 0, then
the DMA takes the descriptor address where it was stopped earlier.

The stmmac_tx_err() does zero indices to Tx descriptors, but does
not reset HW current Tx descriptor address. To fix inconsistency,
the base address of the Tx descriptors should be rewritten before
restarting Tx.
Signed-off-by: NJongsung Kim <neidhard.kim@lge.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The EEE support has not been enabled on ENETC, but it may connect
to a PHY which supports EEE and advertises EEE by default, while
its link partner also advertises EEE. If this happens, the PHY enters
low power mode when the traffic rate is low and causes packet loss.
This patch disables EEE advertisement by default for any PHY that
ENETC connects to, to prevent the above unwanted outcome.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: NClaudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, when set VF VLAN with command "ip link set <pf name>
vf <vf id> vlan <vlan id>", the VF ID 0 is handled as PF incorrectly,
which should be the first VF. This patch fixes it.

Fixes: 21e043cd ("net: hns3: fix set port based VLAN for PF")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, hns3_nic_maybe_stop_tx() uses skb_copy() to linearize a
SKB if the BD num required by the SKB does not meet the hardware
limitation, and it linearizes the SKB by allocating a new linearized SKB
and freeing the old SKB, if hns3_nic_maybe_stop_tx() returns -EBUSY
because there are no enough space in the ring to send the linearized
skb to hardware, the sch_direct_xmit() still hold reference to old SKB
and try to retransmit the old SKB when dev_hard_start_xmit() return
TX_BUSY, which may cause use after freed problem.

This patch fixes it by using __skb_linearize() to linearize the
SKB in hns3_nic_maybe_stop_tx().

Fixes: 51e8439f ("net: hns3: add 8 BD limit for tx flow")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is timing window between ring_space checking and
netif_stop_subqueue when transmiting a SKB, and the TX BD
cleaning may be executed during the time window, which may
caused TX queue not restarted problem.

This patch fixes it by rechecking the ring_space after
netif_stop_subqueue to make sure TX queue is restarted.

Also, the ring->next_to_clean is updated even when pkts is
zero, because all the TX BD cleaned may be non-SKB, so it
needs to check if TX queue need to be restarted.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>