This simplifies the way that the book3s_pr makes the transition to
real mode when entering the guest.  We now call kvmppc_entry_trampoline
(renamed from kvmppc_rmcall) in the base kernel using a normal function
call instead of doing an indirect call through a pointer in the vcpu.
If kvm is a module, the module loader takes care of generating a
trampoline as it does for other calls to functions outside the module.

kvmppc_entry_trampoline then disables interrupts and jumps to
kvmppc_handler_trampoline_enter in real mode using an rfi[d].
That then uses the link register as the address to return to
(potentially in module space) when the guest exits.

This also simplifies the way that we call the Linux interrupt handler
when we exit the guest due to an external, decrementer or performance
monitor interrupt.  Instead of turning on the MMU, then deciding that
we need to call the Linux handler and turning the MMU back off again,
we now go straight to the handler at the point where we would turn the
MMU on.  The handler will then return to the virtual-mode code
(potentially in the module).

Along the way, this moves the setting and clearing of the HID5 DCBZ32
bit into real-mode interrupts-off code, and also makes sure that
we clear the MSR[RI] bit before loading values into SRR0/1.

The net result is that we no longer need any code addresses to be
stored in vcpu->arch.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

There are multiple features in PowerPC KVM that can now be enabled
depending on the user's wishes. Some of the combinations don't make
sense or don't work though.

So this patch adds a way to check if the executing environment would
actually be able to run the guest properly. It also adds sanity
checks if PVR is set (should always be true given the current code
flow), if PAPR is only used with book3s_64 where it works and that
HV KVM is only used in PAPR mode.
Signed-off-by: NAlexander Graf <agraf@suse.de>

When running a PAPR guest, some things change. The privilege level drops
from hypervisor to supervisor, SDR1 gets treated differently and we interpret
hypercalls. For bisectability sake, add the flag now, but only enable it when
all the support code is there.
Signed-off-by: NAlexander Graf <agraf@suse.de>

This adds support for running KVM guests in supervisor mode on those
PPC970 processors that have a usable hypervisor mode.  Unfortunately,
Apple G5 machines have supervisor mode disabled (MSR[HV] is forced to
1), but the YDL PowerStation does have a usable hypervisor mode.

There are several differences between the PPC970 and POWER7 in how
guests are managed.  These differences are accommodated using the
CPU_FTR_ARCH_201 (PPC970) and CPU_FTR_ARCH_206 (POWER7) CPU feature
bits.  Notably, on PPC970:

* The LPCR, LPID or RMOR registers don't exist, and the functions of
  those registers are provided by bits in HID4 and one bit in HID0.

* External interrupts can be directed to the hypervisor, but unlike
  POWER7 they are masked by MSR[EE] in non-hypervisor modes and use
  SRR0/1 not HSRR0/1.

* There is no virtual RMA (VRMA) mode; the guest must use an RMO
  (real mode offset) area.

* The TLB entries are not tagged with the LPID, so it is necessary to
  flush the whole TLB on partition switch.  Furthermore, when switching
  partitions we have to ensure that no other CPU is executing the tlbie
  or tlbsync instructions in either the old or the new partition,
  otherwise undefined behaviour can occur.

* The PMU has 8 counters (PMC registers) rather than 6.

* The DSCR, PURR, SPURR, AMR, AMOR, UAMOR registers don't exist.

* The SLB has 64 entries rather than 32.

* There is no mediated external interrupt facility, so if we switch to
  a guest that has a virtual external interrupt pending but the guest
  has MSR[EE] = 0, we have to arrange to have an interrupt pending for
  it so that we can get control back once it re-enables interrupts.  We
  do that by sending ourselves an IPI with smp_send_reschedule after
  hard-disabling interrupts.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This adds infrastructure which will be needed to allow book3s_hv KVM to
run on older POWER processors, including PPC970, which don't support
the Virtual Real Mode Area (VRMA) facility, but only the Real Mode
Offset (RMO) facility.  These processors require a physically
contiguous, aligned area of memory for each guest.  When the guest does
an access in real mode (MMU off), the address is compared against a
limit value, and if it is lower, the address is ORed with an offset
value (from the Real Mode Offset Register (RMOR)) and the result becomes
the real address for the access.  The size of the RMA has to be one of
a set of supported values, which usually includes 64MB, 128MB, 256MB
and some larger powers of 2.

Since we are unlikely to be able to allocate 64MB or more of physically
contiguous memory after the kernel has been running for a while, we
allocate a pool of RMAs at boot time using the bootmem allocator.  The
size and number of the RMAs can be set using the kvm_rma_size=xx and
kvm_rma_count=xx kernel command line options.

KVM exports a new capability, KVM_CAP_PPC_RMA, to signal the availability
of the pool of preallocated RMAs.  The capability value is 1 if the
processor can use an RMA but doesn't require one (because it supports
the VRMA facility), or 2 if the processor requires an RMA for each guest.

This adds a new ioctl, KVM_ALLOCATE_RMA, which allocates an RMA from the
pool and returns a file descriptor which can be used to map the RMA.  It
also returns the size of the RMA in the argument structure.

Having an RMA means we will get multiple KMV_SET_USER_MEMORY_REGION
ioctl calls from userspace.  To cope with this, we now preallocate the
kvm->arch.ram_pginfo array when the VM is created with a size sufficient
for up to 64GB of guest memory.  Subsequently we will get rid of this
array and use memory associated with each memslot instead.

This moves most of the code that translates the user addresses into
host pfns (page frame numbers) out of kvmppc_prepare_vrma up one level
to kvmppc_core_prepare_memory_region.  Also, instead of having to look
up the VMA for each page in order to check the page size, we now check
that the pages we get are compound pages of 16MB.  However, if we are
adding memory that is mapped to an RMA, we don't bother with calling
get_user_pages_fast and instead just offset from the base pfn for the
RMA.

Typically the RMA gets added after vcpus are created, which makes it
inconvenient to have the LPCR (logical partition control register) value
in the vcpu->arch struct, since the LPCR controls whether the processor
uses RMA or VRMA for the guest.  This moves the LPCR value into the
kvm->arch struct and arranges for the MER (mediated external request)
bit, which is the only bit that varies between vcpus, to be set in
assembly code when going into the guest if there is a pending external
interrupt request.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This lifts the restriction that book3s_hv guests can only run one
hardware thread per core, and allows them to use up to 4 threads
per core on POWER7.  The host still has to run single-threaded.

This capability is advertised to qemu through a new KVM_CAP_PPC_SMT
capability.  The return value of the ioctl querying this capability
is the number of vcpus per virtual CPU core (vcore), currently 4.

To use this, the host kernel should be booted with all threads
active, and then all the secondary threads should be offlined.
This will put the secondary threads into nap mode.  KVM will then
wake them from nap mode and use them for running guest code (while
they are still offline).  To wake the secondary threads, we send
them an IPI using a new xics_wake_cpu() function, implemented in
arch/powerpc/sysdev/xics/icp-native.c.  In other words, at this stage
we assume that the platform has a XICS interrupt controller and
we are using icp-native.c to drive it.  Since the woken thread will
need to acknowledge and clear the IPI, we also export the base
physical address of the XICS registers using kvmppc_set_xics_phys()
for use in the low-level KVM book3s code.

When a vcpu is created, it is assigned to a virtual CPU core.
The vcore number is obtained by dividing the vcpu number by the
number of threads per core in the host.  This number is exported
to userspace via the KVM_CAP_PPC_SMT capability.  If qemu wishes
to run the guest in single-threaded mode, it should make all vcpu
numbers be multiples of the number of threads per core.

We distinguish three states of a vcpu: runnable (i.e., ready to execute
the guest), blocked (that is, idle), and busy in host.  We currently
implement a policy that the vcore can run only when all its threads
are runnable or blocked.  This way, if a vcpu needs to execute elsewhere
in the kernel or in qemu, it can do so without being starved of CPU
by the other vcpus.

When a vcore starts to run, it executes in the context of one of the
vcpu threads.  The other vcpu threads all go to sleep and stay asleep
until something happens requiring the vcpu thread to return to qemu,
or to wake up to run the vcore (this can happen when another vcpu
thread goes from busy in host state to blocked).

It can happen that a vcpu goes from blocked to runnable state (e.g.
because of an interrupt), and the vcore it belongs to is already
running.  In that case it can start to run immediately as long as
the none of the vcpus in the vcore have started to exit the guest.
We send the next free thread in the vcore an IPI to get it to start
to execute the guest.  It synchronizes with the other threads via
the vcore->entry_exit_count field to make sure that it doesn't go
into the guest if the other vcpus are exiting by the time that it
is ready to actually enter the guest.

Note that there is no fixed relationship between the hardware thread
number and the vcpu number.  Hardware threads are assigned to vcpus
as they become runnable, so we will always use the lower-numbered
hardware threads in preference to higher-numbered threads if not all
the vcpus in the vcore are runnable, regardless of which vcpus are
runnable.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This improves I/O performance for guests using the PAPR
paravirtualization interface by making the H_PUT_TCE hcall faster, by
implementing it in real mode.  H_PUT_TCE is used for updating virtual
IOMMU tables, and is used both for virtual I/O and for real I/O in the
PAPR interface.

Since this moves the IOMMU tables into the kernel, we define a new
KVM_CREATE_SPAPR_TCE ioctl to allow qemu to create the tables.  The
ioctl returns a file descriptor which can be used to mmap the newly
created table.  The qemu driver models use them in the same way as
userspace managed tables, but they can be updated directly by the
guest with a real-mode H_PUT_TCE implementation, reducing the number
of host/guest context switches during guest IO.

There are certain circumstances where it is useful for userland qemu
to write to the TCE table even if the kernel H_PUT_TCE path is used
most of the time.  Specifically, allowing this will avoid awkwardness
when we need to reset the table.  More importantly, we will in the
future need to write the table in order to restore its state after a
checkpoint resume or migration.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This adds the infrastructure for handling PAPR hcalls in the kernel,
either early in the guest exit path while we are still in real mode,
or later once the MMU has been turned back on and we are in the full
kernel context.  The advantage of handling hcalls in real mode if
possible is that we avoid two partition switches -- and this will
become more important when we support SMT4 guests, since a partition
switch means we have to pull all of the threads in the core out of
the guest.  The disadvantage is that we can only access the kernel
linear mapping, not anything vmalloced or ioremapped, since the MMU
is off.

This also adds code to handle the following hcalls in real mode:

H_ENTER       Add an HPTE to the hashed page table
H_REMOVE      Remove an HPTE from the hashed page table
H_READ        Read HPTEs from the hashed page table
H_PROTECT     Change the protection bits in an HPTE
H_BULK_REMOVE Remove up to 4 HPTEs from the hashed page table
H_SET_DABR    Set the data address breakpoint register

Plus code to handle the following hcalls in the kernel:

H_CEDE        Idle the vcpu until an interrupt or H_PROD hcall arrives
H_PROD        Wake up a ceded vcpu
H_REGISTER_VPA Register a virtual processor area (VPA)

The code that runs in real mode has to be in the base kernel, not in
the module, if KVM is compiled as a module.  The real-mode code can
only access the kernel linear mapping, not vmalloc or ioremap space.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This adds support for KVM running on 64-bit Book 3S processors,
specifically POWER7, in hypervisor mode.  Using hypervisor mode means
that the guest can use the processor's supervisor mode.  That means
that the guest can execute privileged instructions and access privileged
registers itself without trapping to the host.  This gives excellent
performance, but does mean that KVM cannot emulate a processor
architecture other than the one that the hardware implements.

This code assumes that the guest is running paravirtualized using the
PAPR (Power Architecture Platform Requirements) interface, which is the
interface that IBM's PowerVM hypervisor uses.  That means that existing
Linux distributions that run on IBM pSeries machines will also run
under KVM without modification.  In order to communicate the PAPR
hypercalls to qemu, this adds a new KVM_EXIT_PAPR_HCALL exit code
to include/linux/kvm.h.

Currently the choice between book3s_hv support and book3s_pr support
(i.e. the existing code, which runs the guest in user mode) has to be
made at kernel configuration time, so a given kernel binary can only
do one or the other.

This new book3s_hv code doesn't support MMIO emulation at present.
Since we are running paravirtualized guests, this isn't a serious
restriction.

With the guest running in supervisor mode, most exceptions go straight
to the guest.  We will never get data or instruction storage or segment
interrupts, alignment interrupts, decrementer interrupts, program
interrupts, single-step interrupts, etc., coming to the hypervisor from
the guest.  Therefore this introduces a new KVMTEST_NONHV macro for the
exception entry path so that we don't have to do the KVM test on entry
to those exception handlers.

We do however get hypervisor decrementer, hypervisor data storage,
hypervisor instruction storage, and hypervisor emulation assist
interrupts, so we have to handle those.

In hypervisor mode, real-mode accesses can access all of RAM, not just
a limited amount.  Therefore we put all the guest state in the vcpu.arch
and use the shadow_vcpu in the PACA only for temporary scratch space.
We allocate the vcpu with kzalloc rather than vzalloc, and we don't use
anything in the kvmppc_vcpu_book3s struct, so we don't allocate it.
We don't have a shared page with the guest, but we still need a
kvm_vcpu_arch_shared struct to store the values of various registers,
so we include one in the vcpu_arch struct.

The POWER7 processor has a restriction that all threads in a core have
to be in the same partition.  MMU-on kernel code counts as a partition
(partition 0), so we have to do a partition switch on every entry to and
exit from the guest.  At present we require the host and guest to run
in single-thread mode because of this hardware restriction.

This code allocates a hashed page table for the guest and initializes
it with HPTEs for the guest's Virtual Real Memory Area (VRMA).  We
require that the guest memory is allocated using 16MB huge pages, in
order to simplify the low-level memory management.  This also means that
we can get away without tracking paging activity in the host for now,
since huge pages can't be paged or swapped.

This also adds a few new exports needed by the book3s_hv code.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This moves the slb field, which represents the state of the emulated
SLB, from the kvmppc_vcpu_book3s struct to the kvm_vcpu_arch, and the
hpte_hash_[v]pte[_long] fields from kvm_vcpu_arch to kvmppc_vcpu_book3s.
This is in accord with the principle that the kvm_vcpu_arch struct
represents the state of the emulated CPU, and the kvmppc_vcpu_book3s
struct holds the auxiliary data structures used in the emulation.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Dynamically assign host PIDs to guest PIDs, splitting each guest PID into
multiple host (shadow) PIDs based on kernel/user and MSR[IS/DS].  Use
both PID0 and PID1 so that the shadow PIDs for the right mode can be
selected, that correspond both to guest TID = zero and guest TID = guest
PID.

This allows us to significantly reduce the frequency of needing to
invalidate the entire TLB.  When the guest mode or PID changes, we just
update the host PID0/PID1.  And since the allocation of shadow PIDs is
global, multiple guests can share the TLB without conflict.

Note that KVM does not yet support the guest setting PID1 or PID2 to
a value other than zero.  This will need to be fixed for nested KVM
to work.  Until then, we enforce the requirement for guest PID1/PID2
to stay zero by failing the emulation if the guest tries to set them
to something else.
Signed-off-by: NLiu Yu <yu.liu@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This is done lazily.  The SPE save will be done only if the guest has
used SPE since the last preemption or heavyweight exit.  Restore will be
done only on demand, when enabling MSR_SPE in the shadow MSR, in response
to an SPE fault or mtmsr emulation.

For SPEFSCR, Linux already switches it on context switch (non-lazily), so
the only remaining bit is to save it between qemu and the guest.
Signed-off-by: NLiu Yu <yu.liu@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Keep the guest MSR and the guest-mode true MSR separate, rather than
modifying the guest MSR on each guest entry to produce a true MSR.

Any bits which should be modified based on guest MSR must be explicitly
propagated from vcpu->arch.shared->msr to vcpu->arch.shadow_msr in
kvmppc_set_msr().

While we're modifying the guest entry code, reorder a few instructions
to bury some load latencies.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Linux doesn't use USPRG0 (now renamed VRSAVE in the architecture, even
when Altivec isn't involved), but a guest might.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Following dump is observed on host when clearing the exit timing counters

[root@p1021mds kvm]# echo -n 'c' > vm1200_vcpu0_timing
INFO: task echo:1276 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
echo          D 0ff5bf94     0  1276   1190 0x00000000
Call Trace:
[c2157e40] [c0007908] __switch_to+0x9c/0xc4
[c2157e50] [c040293c] schedule+0x1b4/0x3bc
[c2157e90] [c04032dc] __mutex_lock_slowpath+0x74/0xc0
[c2157ec0] [c00369e4] kvmppc_init_timing_stats+0x20/0xb8
[c2157ed0] [c0036b00] kvmppc_exit_timing_write+0x84/0x98
[c2157ef0] [c00b9f90] vfs_write+0xc0/0x16c
[c2157f10] [c00ba284] sys_write+0x4c/0x90
[c2157f40] [c000e320] ret_from_syscall+0x0/0x3c

        The vcpu->mutex is used by kvm_ioctl_* (KVM_RUN etc) and same was
used when clearing the stats (in kvmppc_init_timing_stats()). What happens
is that when the guest is idle then it held the vcpu->mutx. While the
exiting timing process waits for guest to release the vcpu->mutex and
a hang state is reached.

        Now using seprate lock for exit timing stats.
Signed-off-by: NBharat Bhushan <Bharat.Bhushan@freescale.com>
Acked-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

On Book3s_32 the tlbie instruction flushed effective addresses by the mask
0x0ffff000. This is pretty hard to reflect with a hash that hashes ~0xfff, so
to speed up that target we should also keep a special hash around for it.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

So far we've been running all code without locking of any sort. This wasn't
really an issue because I didn't see any parallel access to the shadow MMU
code coming.

But then I started to implement dirty bitmapping to MOL which has the video
code in its own thread, so suddenly we had the dirty bitmap code run in
parallel to the shadow mmu code. And with that came trouble.

So I went ahead and made the MMU modifying functions as parallelizable as
I could think of. I hope I didn't screw up too much RCU logic :-). If you
know your way around RCU and locking and what needs to be done when, please
take a look at this patch.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

We will be introducing a method to project the shared page in guest context.
As soon as we're talking about this coupling, the shared page is colled magic
page.

This patch introduces simple defines, so the follow-up patches are easier to
read.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

On PowerPC it's very normal to not support all of the physical RAM in real mode.
To check if we're matching on the shared page or not, we need to know the limits
so we can restrain ourselves to that range.

So let's make it a define instead of open-coding it. And while at it, let's also
increase it.
Signed-off-by: NAlexander Graf <agraf@suse.de>

v2 -> v3:

  - RMO -> PAM (non-magic page)
Signed-off-by: NAvi Kivity <avi@redhat.com>

When in kernel mode there are 4 additional registers available that are
simple data storage. Instead of exiting to the hypervisor to read and
write those, we can just share them with the guest using the page.

This patch converts all users of the current field to the shared page.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

The SRR0 and SRR1 registers contain cached values of the PC and MSR
respectively. They get written to by the hypervisor when an interrupt
occurs or directly by the kernel. They are also used to tell the rfi(d)
instruction where to jump to.

Because it only gets touched on defined events that, it's very simple to
share with the guest. Hypervisor and guest both have full r/w access.

This patch converts all users of the current field to the shared page.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

The DAR register contains the address a data page fault occured at. This
register behaves pretty much like a simple data storage register that gets
written to on data faults. There is no hypervisor interaction required on
read or write.

This patch converts all users of the current field to the shared page.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

One of the most obvious registers to share with the guest directly is the
MSR. The MSR contains the "interrupts enabled" flag which the guest has to
toggle in critical sections.

So in order to bring the overhead of interrupt en- and disabling down, let's
put msr into the shared page. Keep in mind that even though you can fully read
its contents, writing to it doesn't always update all state. There are a few
safe fields that don't require hypervisor interaction. See the documentation
for a list of MSR bits that are safe to be set from inside the guest.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

For transparent variable sharing between the hypervisor and guest, I introduce
a shared page. This shared page will contain all the registers the guest can
read and write safely without exiting guest context.

This patch only implements the stubs required for the basic structure of the
shared page. The actual register moving follows.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

This patch converts unnecessary divide and modulo operations
in the KVM large page related code into logical operations.
This allows to convert gfn_t to u64 while not breaking 32
bit builds.
Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

We just introduced generic functions to handle shadow pages on PPC.
This patch makes the respective backends make use of them, getting
rid of a lot of duplicate code along the way.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

There are some pieces in the code that I overlooked that still use
u64s instead of longs. This slows down 32 bit hosts unnecessarily, so
let's just move them to ulong.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

The shadow vcpu now contains some fields we don't use from the vcpu anymore.
Access to them happens using inline functions that happily use the shadow
vcpu fields.

So let's now ifdef them out to booke only and add asm-offsets.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Upstream recently added a new name for PPC64: Book3S_64.

So instead of using CONFIG_PPC64 we should use CONFIG_PPC_BOOK3S consotently.
That makes understanding the code easier (I hope).
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Bool defaults to at least byte width. We usually only want to waste a single
bit on this. So let's move all the bool values to bitfields, potentially
saving memory.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

MOL uses its own hypercall interface to call back into userspace when
the guest wants to do something.

So let's implement that as an exit reason, specify it with a CAP and
only really use it when userspace wants us to.

The only user of it so far is MOL.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

DSISR is only defined as 32 bits wide. So let's reflect that in the
structs too.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

The guest I was trying to get to run uses the LHA and LHAU instructions.
Those instructions basically do a load, but also sign extend the result.

Since we need to fill our registers by hand when doing MMIO, we also need
to sign extend manually.

This patch implements sign extended MMIO and the LHA(U) instructions.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Modern PowerPCs have a 64 bit wide FPSCR register. Let's accomodate for that
and make it 64 bits in our vcpu struct too.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

The Gekko has GPRs, SPRs and FPRs like normal PowerPC codes, but
it also has QPRs which are basically single precision only FPU registers
that get used when in paired single mode.

The following patches depend on them being around, so let's add the
definitions early.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Old method prematurely sets ESR and DEAR.
Move this part after we decide to inject interrupt,
which is more like hardware behave.
Signed-off-by: NLiu Yu <yu.liu@freescale.com>
Acked-by: NHollis Blanchard <hollis@penguinppc.org>
Acked-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

SRR1 stores more information that just the MSR value. It also stores
valuable information about the type of interrupt we received, for
example whether the storage interrupt we just got was because of a
missing htab entry or not.

We use that information to speed up the exit path.

Now if we get preempted before we can interpret the shadow_msr values,
we get into vcpu_put which then calls the MSR handler, which then sets
all the SRR1 information bits in shadow_msr to 0. Great.

So let's preserve the SRR1 specific bits in shadow_msr whenever we set
the MSR. They don't hurt.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

When our guest starts using either the FPU, Altivec or VSX we need to make
sure Linux knows about it and sneak into its process switching code
accordingly.

This patch makes accesses to the above parts of the system work inside the
VM.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Currently we're racy when doing the transition from IR=1 to IR=0, from
the module memory entry code to the real mode SLB switching code.

To work around that I took a look at the RTAS entry code which is faced
with a similar problem and did the same thing:

  A small helper in linear mapped memory that does mtmsr with IR=0 and
  then RFIs info the actual handler.

Thanks to that trick we can safely take page faults in the entry code
and only need to be really wary of what to do as of the SLB switching
part.
Signed-off-by: NAlexander Graf <agraf@suse.de>
Signed-off-by: NAvi Kivity <avi@redhat.com>