Pull pin control fixes from Linus Walleij:
 "Here is a slew of pin control fixes I've accumulated for the v4.0
  kernel.  Nothing special, just driver fixes (mainly embedded Intel it
  seems) and a misunderstanding regarding the stub functions was
  reverted:

   - Fix up consumer return values on pin control stubs.
   - Four patches fixing up the interrupt handling and sleep context
     save in the Baytrail driver.
   - Make default output directions work properly in the Cherryview
     driver.
   - Fix interrupt locking in the AT91 driver.
   - Fix setting interrupt generating lines as input in the sunxi
     driver"

* tag 'pinctrl-v4.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: sun4i: GPIOs configured as irq must be set to input before reading
  pinctrl: at91: move lock/unlock_as_irq calls into request/release
  pinctrl: update direction_output function of cherryview driver
  pinctrl: baytrail: Save pin context over system sleep
  pinctrl: baytrail: Rework interrupt handling
  pinctrl: baytrail: Clear interrupt triggering from pins that are in GPIO mode
  pinctrl: baytrail: Relax GPIO request rules
  Revert "pinctrl: consumer: use correct retval for placeholder functions"

Pull two arch/nios2 fixes from Ley Foon Tan:
 - Remove ucontext.h from exported arch headers
 - nios2: mm: do not invoke OOM killer on kernel fault OOM

* tag 'nios2-fixes-v4.0-rc5' of git://git.rocketboards.org/linux-socfpga-next:
  nios2: mm: do not invoke OOM killer on kernel fault OOM
  nios2: Remove ucontext.h from exported arch headers

Pull IDE fix from David Miller:
 "Just one fix to convert a by-hand conversion of jiffies to msecs, from
  Nicholas McGuire"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide:
  ide_tape: convert jiffies with jiffies_to_msecs

Pull sparc fixes from David Miller:

 1) Some command cases of semtimedop() not even handled due to miscoded
    comparison on sparc64.  From Rob Gardner.

 2) Due to two bugs, /proc/kcore wan't working properly on sparc.

 3) Make sure fatal traps stop all running cpus, from Dave Kleikamp.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc: Fix /proc/kcore
  sparc: semtimedop() unreachable due to comparison error
  sparc: io_64.h: Replace io function-link macros
  sparc64: fatal trap should stop all cpus
  arch: sparc: kernel: starfire.c: Remove unused function
  arch: sparc: kernel: traps_64.c: Remove some unused functions

Pull networking fixes from David Miller:

 1) Fix packet header offset calculation in _decode_session6(), from
    Hajime Tazaki.

 2) Fix route leak in error paths of xfrm_lookup(), from Huaibin Wang.

 3) Be sure to clear state properly when scans fail in iwlwifi mvm code,
    from Luciano Coelho.

 4) iwlwifi tries to stop scans that aren't actually running, also from
    Luciano Coelho.

 5) mac80211 should drop mesh frames that are not encrypted, fix from
    Bob Copeland.

 6) Add new device ID to b43 wireless driver for BCM432228 chips, from
    Rafał Miłecki.

 7) Fix accidental addition of members after variable sized array in
    struct tc_u_hnode, from WANG Cong.

 8) Don't re-enable interrupts until after we call napi_complete() in
    ibmveth and WIZnet drivers, frm Yongbae Park.

 9) Fix regression in vlan tag handling of fec driver, from Fugang Duan.

10) If a network namespace change fails during rtnl_newlink(), we don't
    unwind the device registry properly.

11) Fix two TCP regressions, from Neal Cardwell:
  - Don't allow snd_cwnd_cnt to accumulate huge values due to missing
    test in tcp_cong_avoid_ai().
  - Restore CUBIC back to advancing cwnd by 1.5x packets per RTT.

12) Fix performance regression in xne-netback involving push TX
    notifications, from David Vrabel.

13) __skb_tstamp_tx() can be called with a NULL sk pointer, do not
    dereference blindly.  From Willem de Bruijn.

14) Fix potential stack overflow in RDS protocol stack, from Arnd
    Bergmann.

15) VXLAN_VID_MASK used incorrectly in new remote checksum offload
    support of VXLAN driver.  Fix from Alexey Kodanev.

16) Fix too small netlink SKB allocation in inet_diag layer, from Eric
    Dumazet.

17) ieee80211_check_combinations() does not count interfaces correctly,
    from Andrei Otcheretianski.

18) Hardware feature determination in bxn2x driver references a piece of
    software state that actually isn't initialized yet, fix from Michal
    Schmidt.

19) inet_csk_wait_for_connect() needs a sched_annotate_sleep()
    annoation, from Eric Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (56 commits)
  Revert "net: cx82310_eth: use common match macro"
  net/mlx4_en: Set statistics bitmap at port init
  IB/mlx4: Saturate RoCE port PMA counters in case of overflow
  net/mlx4_en: Fix off-by-one in ethtool statistics display
  IB/mlx4: Verify net device validity on port change event
  act_bpf: allow non-default TC_ACT opcodes as BPF exec outcome
  Revert "smc91x: retrieve IRQ and trigger flags in a modern way"
  inet: Clean up inet_csk_wait_for_connect() vs. might_sleep()
  ip6_tunnel: fix error code when tunnel exists
  netdevice.h: fix ndo_bridge_* comments
  bnx2x: fix encapsulation features on 57710/57711
  mac80211: ignore CSA to same channel
  nl80211: ignore HT/VHT capabilities without QoS/WMM
  mac80211: ask for ECSA IE to be considered for beacon parse CRC
  mac80211: count interfaces correctly for combination checks
  isdn: icn: use strlcpy() when parsing setup options
  rxrpc: bogus MSG_PEEK test in rxrpc_recvmsg()
  caif: fix MSG_OOB test in caif_seqpkt_recvmsg()
  bridge: reset bridge mtu after deleting an interface
  can: kvaser_usb: Fix tx queue start/stop race conditions
  ...

Use jiffies_to_msecs for converting jiffies as it handles all of the corner
cases reliably and also helps readability. The printk format is fixed up
as jiffies_to_msecs returns unsigned int not unsigned long.
Signed-off-by: NNicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 11ad714b because
it breaks cx82310_eth.

The custom USB_DEVICE_CLASS macro matches
bDeviceClass, bDeviceSubClass and bDeviceProtocol
but the common USB_DEVICE_AND_INTERFACE_INFO matches
bInterfaceClass, bInterfaceSubClass and bInterfaceProtocol instead, which are
not specified.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

/proc/kcore investigates the "System RAM" elements in /proc/iomem to
initialize it's memory tables.  Therefore we have to register them
before it tries to do so.  kcore uses device_initcall() so let's
use arch_initcall() for the registry.

Also we need ARCH_PROC_KCORE_TEXT to get the virtual addresses of
the kernel image correct.
Reported-by: NDavid Ahern <david.ahern@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
mlx4 driver fixes for 4.0-rc

Just few small fixes for the 4.0 rc cycle.

The fix from Moni addresses an issue from 4.0-rc1 so we
just need it for net.

Eran's fix for off-by-one should go to 3.19.y too.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Port statistics bitmap will now be initialized at port init.  Even before
starting the port, statistics are visible to the user and must be properly masked.
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For RoCE ports, we set the u32 PMA values based on u64 HCA counters. In case of
overflow, according to the IB spec, we have to saturate a counter to its
max value, do that.

Fixes: c3779134 ('IB/mlx4: Support PMA counters for IBoE')
Signed-off-by: NMajd Dibbiny <majd@mellanox.com>
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NUM_PORT_STATS was 9 instead of 10, which caused off-by-one bug when
displaying the statistics starting from tx_chksum_offload in ethtool.

Fixes: f8c6455b ('net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE')
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Processing an event is done in a different context from the one when
the event was dispatched. This requires a check that the slave
net device is still valid when the event is being processed. The check is done
under the iboe lock which ensure correctness.

Fixes: a5750090 ('IB/mlx4: Add port aggregation support')
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull sound fixes from Takashi Iwai:
 "This is a collection of many small fixes.  Most of fixes are for ASoC
  drivers, including the fixes of wrong field usages for boolean kctls.

  In addition, there is a fix in ASoC core for adding proper locks for
  component lists, and a fix for a HD-audio regression by the previous
  mono channel fix"

* tag 'sound-4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (24 commits)
  ALSA: hda - Treat stereo-to-mono mix properly
  ASoC: wm9713: Fix wrong value references for boolean kctl
  ASoC: wm9712: Fix wrong value references for boolean kctl
  ASoC: wm8960: Fix wrong value references for boolean kctl
  ASoC: wm8955: Fix wrong value references for boolean kctl
  ASoC: wm8904: Fix wrong value references for boolean kctl
  ASoC: wm8903: Fix wrong value references for boolean kctl
  ASoC: wm8731: Fix wrong value references for boolean kctl
  ASoC: wm2000: Fix wrong value references for boolean kctl
  ASoC: tas5086: Fix wrong value references for boolean kctl
  ASoC: pcm1681: Fix wrong value references for boolean kctl
  ASoC: es8238: Fix wrong value references for boolean kctl
  ASoC: cs4271: Fix wrong value references for boolean kctl
  ASoC: ak4641: Fix wrong value references for boolean kctl
  ASoC: adav80x: Fix wrong value references for boolean kctl
  ASoC: Fix component lists locking
  ASoC: Intel: remove conflicts when load/unload multiple firmware images
  ASoC: rt286: Change the DMI mapping for Dino
  ASoC: sgtl5000: remove useless register write clearing CHRGPUMP_POWERUP
  ASoC: fsl_ssi: Don't try to round-up for PM divisor calculation
  ...

Pull crypto fixes from Herbert Xu:
 "Fix a bug in the ARM XTS implementation that can cause failures in
  decrypting encrypted disks, and fix is a memory overwrite bug that can
  cause a crash which can be triggered from userspace"

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: aesni - fix memory usage in GCM decryption
  crypto: arm/aes update NEON AES module to latest OpenSSL version

Pull livepatching fix from Jiri Kosina:

 - fix for potential race with module loading, from Petr Mladek.

   The race is very unlikely to be seen in real world and has been found
   by code inspection, but should be fixed for 4.0 anyway.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
  livepatch: Fix subtle race with coming and going modules

Pull HID fixes from Jiri Kosina:

 - fixes for pen pen proximity / touch events in wacom driver, from Ping
   Cheng and Benjamin Tissoires

 - two new device-specific quirks from Oliver Neukum and Forest
   Wilkinson

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: wacom: check for wacom->shared before following the pointer
  HID: tivo: enable all buttons on the TiVo Slide Pro remote
  HID: add ALWAYS_POLL quirk for a Logitech 0xc007
  HID: wacom: rely on actual touch down count to decide touch_down
  HID: wacom: do not send pen events before touch is up/forced out

On sun4i-a10, when GPIOs are configured as external interrupt the value for
them in the data register does not seem to get updated, so set their mux to
input (and restore afterwards) when reading the pin.

Missed edges seem to be buffered, so this does not introduce a race
condition.

I've also tested this on sun5i-a13 and sun7i-a20 and those do not seem to
be affected, the input value representation in the data register does seem
to correctly get updated to the actual pin value while in irq mode there.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Revisiting commit d23b8ad8 ("tc: add BPF based action") with regards
to eBPF support, I was thinking that it might be better to improve
return semantics from a BPF program invoked through BPF_PROG_RUN().

Currently, in case filter_res is 0, we overwrite the default action
opcode with TC_ACT_SHOT. A default action opcode configured through tc's
m_bpf can be: TC_ACT_RECLASSIFY, TC_ACT_PIPE, TC_ACT_SHOT, TC_ACT_UNSPEC,
TC_ACT_OK.

In cls_bpf, we have the possibility to overwrite the default class
associated with the classifier in case filter_res is _not_ 0xffffffff
(-1).

That allows us to fold multiple [e]BPF programs into a single one, where
they would otherwise need to be defined as a separate classifier with
its own classid, needlessly redoing parsing work, etc.

Similarly, we could do better in act_bpf: Since above TC_ACT* opcodes
are exported to UAPI anyway, we reuse them for return-code-to-tc-opcode
mapping, where we would allow above possibilities. Thus, like in cls_bpf,
a filter_res of 0xffffffff (-1) means that the configured _default_ action
is used. Any unkown return code from the BPF program would fail in
tcf_bpf() with TC_ACT_UNSPEC.

Should we one day want to make use of TC_ACT_STOLEN or TC_ACT_QUEUED,
which both have the same semantics, we have the option to either use
that as a default action (filter_res of 0xffffffff) or non-default BPF
return code.

All that will allow us to transparently use tcf_bpf() for both BPF
flavours.
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The gpiochip_lock_as_irq call can fail and return an error,
while the irq_startup is not expected to fail (returns an
unsigned int which is not checked by irq core code).

irq_request/release_resources functions have been created
to address this problem.

Move gpiochip_lock/unlock_as_irq calls into
irq_request/release_resources functions to prevent using a
gpio as an irq if the gpiochip_lock_as_irq call failed.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Pull x86 fixes from Ingo Molnar:
 "Misc fixes from all around the place:

   - a KASLR related revert where we ran out of time to get a fix - this
     represents a substantial portion of the diffstat,

   - two FPU fixes,

   - two x86 platform fixes: an ACPI reduced-hw fix and a NumaChip fix,

   - an entry code fix,

   - and a VDSO build fix"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  Revert "x86/mm/ASLR: Propagate base load address calculation"
  x86/fpu: Drop_fpu() should not assume that tsk equals current
  x86/fpu: Avoid math_state_restore() without used_math() in __restore_xstate_sig()
  x86/apic/numachip: Fix sibling map with NumaChip
  x86/platform, acpi: Bypass legacy PIC and PIT in ACPI hardware reduced mode
  x86/asm/entry/32: Fix user_mode() misuses
  x86/vdso: Fix the build on GCC5

Merge branches 'perf-urgent-for-linus' and 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull perf and timer fixes from Ingo Molnar:
 "Two small perf fixes:
   - kernel side context leak fix
   - tooling crash fix

  And two clocksource driver fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: Fix context leak in put_event()
  perf annotate: Fix fallback to unparsed disassembler line

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clockevents: sun5i: Fix setup_irq init sequence
  clocksource: efm32: Fix a NULL pointer dereference

486b908d (HID: wacom: do not send pen events before touch is up/forced out)
introduces a kernel oops when plugging a tablet without touch.

wacom->shared is null for these devices so this leads to a null pointer
exception.

Change the condition to make it clear that what we need is wacom->shared
not NULL.
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The commit breaks the legacy platforms, ie. these not using device-tree,
and setting up the interrupt resources with a flag to activate edge
detection. The issue was found on the zylonite platform.

The reason is that zylonite uses platform resources to pass the interrupt number
and the irq flags (here IORESOURCE_IRQ_HIGHEDGE). It expects the driver to
request the irq with these flags, which in turn setups the irq as high edge
triggered.

After the patch, this was supposed to be taken care of with :
  irq_resflags = irqd_get_trigger_type(irq_get_irq_data(ndev->irq));

But irq_resflags is 0 for legacy platforms, while for example in
arch/arm/mach-pxa/zylonite.c, in struct resource smc91x_resources[] the
irq flag is specified. This breaks zylonite because the interrupt is not
setup as triggered, and hardware doesn't provide interrupts.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I got the following trace with current net-next kernel :

[14723.885290] WARNING: CPU: 26 PID: 22658 at kernel/sched/core.c:7285 __might_sleep+0x89/0xa0()
[14723.885325] do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffff810e8734>] prepare_to_wait_exclusive+0x34/0xa0
[14723.885355] CPU: 26 PID: 22658 Comm: netserver Not tainted 4.0.0-dbg-DEV #1379
[14723.885359]  ffffffff81a223a8 ffff881fae9e7ca8 ffffffff81650b5d 0000000000000001
[14723.885364]  ffff881fae9e7cf8 ffff881fae9e7ce8 ffffffff810a72e7 0000000000000000
[14723.885367]  ffffffff81a57620 000000000000093a 0000000000000000 ffff881fae9e7e64
[14723.885371] Call Trace:
[14723.885377]  [<ffffffff81650b5d>] dump_stack+0x4c/0x65
[14723.885382]  [<ffffffff810a72e7>] warn_slowpath_common+0x97/0xe0
[14723.885386]  [<ffffffff810a73e6>] warn_slowpath_fmt+0x46/0x50
[14723.885390]  [<ffffffff810f4c5d>] ? trace_hardirqs_on_caller+0x10d/0x1d0
[14723.885393]  [<ffffffff810e8734>] ? prepare_to_wait_exclusive+0x34/0xa0
[14723.885396]  [<ffffffff810e8734>] ? prepare_to_wait_exclusive+0x34/0xa0
[14723.885399]  [<ffffffff810ccdc9>] __might_sleep+0x89/0xa0
[14723.885403]  [<ffffffff81581846>] lock_sock_nested+0x36/0xb0
[14723.885406]  [<ffffffff815829a3>] ? release_sock+0x173/0x1c0
[14723.885411]  [<ffffffff815ea1f7>] inet_csk_accept+0x157/0x2a0
[14723.885415]  [<ffffffff810e8900>] ? abort_exclusive_wait+0xc0/0xc0
[14723.885419]  [<ffffffff8161b96d>] inet_accept+0x2d/0x150
[14723.885424]  [<ffffffff8157db6f>] SYSC_accept4+0xff/0x210
[14723.885428]  [<ffffffff8165a451>] ? retint_swapgs+0xe/0x44
[14723.885431]  [<ffffffff810f4c5d>] ? trace_hardirqs_on_caller+0x10d/0x1d0
[14723.885437]  [<ffffffff81369c0e>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[14723.885441]  [<ffffffff8157ef40>] SyS_accept+0x10/0x20
[14723.885444]  [<ffffffff81659872>] system_call_fastpath+0x12/0x17
[14723.885447] ---[ end trace ff74cd83355b1873 ]---

In commit 26cabd31
Peter added a sched_annotate_sleep() in sk_wait_event()

Is the following patch needed as well ?

Alternative would be to use sk_wait_event() from inet_csk_wait_for_connect()
Signed-off-by: NEric Dumazet <edumazet@google.com>
Acked-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After commit 2b0bb01b, the kernel returns -ENOBUFS when user tries to add
an existing tunnel with ioctl API:
$ ip -6 tunnel add ip6tnl1 mode ip6ip6 dev eth1
add tunnel "ip6tnl0" failed: No buffer space available

It's confusing, the right error is EEXIST.

This patch also change a bit the code returned:
 - ENOBUFS -> ENOMEM
 - ENOENT -> ENODEV

Fixes: 2b0bb01b ("ip6_tunnel: Return an error when adding an existing tunnel.")
CC: Steffen Klassert <steffen.klassert@secunet.com>
Reported-by: NPierre Cheynier <me@pierre-cheynier.net>
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The argument 'flags' was missing in ndo_bridge_setlink().
ndo_bridge_dellink() was missing.

Fixes: 407af329 ("bridge: Add netlink interface to configure vlans on bridge ports")
Fixes: add511b3 ("bridge: add flags argument to ndo_bridge_setlink and ndo_bridge_dellink")
CC: Vlad Yasevich <vyasevic@redhat.com>
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'regulator-fix-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator

Pull regulator fixes from Mark Brown:
 "The two main fixes here from Javier and Doug both fix issues seen on
  the Exynos-based ARM Chromebooks with reference counting of GPIO
  regulators over system suspend.  The GPIO enable code didn't properly
  take account of this case (a full analysis is in Doug's commit log).

  This is fixed by both fixing the reference counting directly and by
  making the resume code skip enables it doesn't need to do.  We could
  skip the change in the resume code but it's a very simple change and
  adds extra robustness against problems in other drivers"

* tag 'regulator-fix-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: tps65910: Add missing #include <linux/of.h>
  regulator: core: Fix enable GPIO reference counting
  regulator: Only enable disabled regulators on resume

Pull regmap fixes from Mark Brown:
 "A few things here:

   - a change from Lars to fix insertion of cache values at the start of
     rather than end of a rbtree block.  This hadn't been noticed before
     since almost everything lists registers in ascending order.

   - a fix from Takashi for spurious warnings during cache sync with
     read once registers, a problem which can be very noticeable on
     devices that it affects.

   - a fix from Valentin for a tighening of the oneshot IRQ request
     interface which would have broken affected devices"

* tag 'regmap-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: regcache-rbtree: Fix present bitmap resize
  regmap: Skip read-only registers in regcache_sync()
  regmap-irq: set IRQF_ONESHOT flag to ensure IRQ request

Pull virtio fixes from Rusty Russell:
 "Not entirely surprising: the ongoing QEMU work on virtio 1.0 has
  revealed more minor issues with our virtio 1.0 drivers just introduced
  in the kernel.

  (I would normally use my fixes branch for this, but there were a batch
  of them...)"

* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
  virtio_mmio: fix access width for mmio
  uapi/virtio_scsi: allow overriding CDB/SENSE size
  virtio_mmio: generation support
  virtio_rpmsg: set DRIVER_OK before using device
  9p/trans_virtio: fix hot-unplug
  virtio-balloon: do not call blocking ops when !TASK_RUNNING
  virtio_blk: fix comment for virtio 1.0
  virtio_blk: typo fix
  virtio_balloon: set DRIVER_OK before using device
  virtio_console: avoid config access from irq
  virtio_console: init work unconditionally

Pull kvm fixes from Marcelo Tosatti:
 "KVM bug fixes (ARM and x86)"

* git://git.kernel.org/pub/scm/virt/kvm/kvm:
  arm/arm64: KVM: Keep elrsr/aisr in sync with software model
  KVM: VMX: Set msr bitmap correctly if vcpu is in guest mode
  arm/arm64: KVM: fix missing unlock on error in kvm_vgic_create()
  kvm: x86: i8259: return initialized data on invalid-size read
  arm64: KVM: Fix outdated comment about VTCR_EL2.PS
  arm64: KVM: Do not use pgd_index to index stage-2 pgd
  arm64: KVM: Fix stage-2 PGD allocation to have per-page refcounting
  kvm: move advertising of KVM_CAP_IRQFD to common code

As pointed by recent post[1] on exploiting DRAM physical imperfection,
/proc/PID/pagemap exposes sensitive information which can be used to do
attacks.

This disallows anybody without CAP_SYS_ADMIN to read the pagemap.

[1] http://googleprojectzero.blogspot.com/2015/03/exploiting-dram-rowhammer-bug-to-gain.html

[ Eventually we might want to do anything more finegrained, but for now
  this is the simple model.   - Linus ]
Signed-off-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: NKonstantin Khlebnikov <khlebnikov@openvz.org>
Acked-by: NAndy Lutomirski <luto@amacapital.net>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Mark Seaborn <mseaborn@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Merge tag 'asoc-fix-v4.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v4.0

As well as the usual collection of driver specific fixes there's a few
more generic things:

 - Lots of fixes from Takashi for drivers using the wrong field in the
   control union to communicate with userspace, leading to potential
   errors on 64 bit systems.
 - A fix from Lars for locking of the lists of devices we maintain,
   mostly only likely to trigger during device probe and removal.

There is a notifier that handles live patches for coming and going modules.
It takes klp_mutex lock to avoid races with coming and going patches but
it does not keep the lock all the time. Therefore the following races are
possible:

  1. The notifier is called sometime in STATE_MODULE_COMING. The module
     is visible by find_module() in this state all the time. It means that
     new patch can be registered and enabled even before the notifier is
     called. It might create wrong order of stacked patches, see below
     for an example.

   2. New patch could still see the module in the GOING state even after
      the notifier has been called. It will try to initialize the related
      object structures but the module could disappear at any time. There
      will stay mess in the structures. It might even cause an invalid
      memory access.

This patch solves the problem by adding a boolean variable into struct module.
The value is true after the coming and before the going handler is called.
New patches need to be applied when the value is true and they need to ignore
the module when the value is false.

Note that we need to know state of all modules on the system. The races are
related to new patches. Therefore we do not know what modules will get
patched.

Also note that we could not simply ignore going modules. The code from the
module could be called even in the GOING state until mod->exit() finishes.
If we start supporting patches with semantic changes between function
calls, we need to apply new patches to any still usable code.
See below for an example.

Finally note that the patch solves only the situation when a new patch is
registered. There are no such problems when the patch is being removed.
It does not matter who disable the patch first, whether the normal
disable_patch() or the module notifier. There is nothing to do
once the patch is disabled.

Alternative solutions:
======================

+ reject new patches when a patched module is coming or going; this is ugly

+ wait with adding new patch until the module leaves the COMING and GOING
  states; this might be dangerous and complicated; we would need to release
  kgr_lock in the middle of the patch registration to avoid a deadlock
  with the coming and going handlers; also we might need a waitqueue for
  each module which seems to be even bigger overhead than the boolean

+ stop modules from entering COMING and GOING states; wait until modules
  leave these states when they are already there; looks complicated; we would
  need to ignore the module that asked to stop the others to avoid a deadlock;
  also it is unclear what to do when two modules asked to stop others and
  both are in COMING state (situation when two new patches are applied)

+ always register/enable new patches and fix up the potential mess (registered
  patches order) in klp_module_init(); this is nasty and prone to regressions
  in the future development

+ add another MODULE_STATE where the kallsyms are visible but the module is not
  used yet; this looks too complex; the module states are checked on "many"
  locations

Example of patch stacking breakage:
===================================

The notifier could _not_ _simply_ ignore already initialized module objects.
For example, let's have three patches (P1, P2, P3) for functions a() and b()
where a() is from vmcore and b() is from a module M. Something like:

	a()	b()
P1	a1()	b1()
P2	a2()	b2()
P3	a3()	b3(3)

If you load the module M after all patches are registered and enabled.
The ftrace ops for function a() and b() has listed the functions in this
order:

	ops_a->func_stack -> list(a3,a2,a1)
	ops_b->func_stack -> list(b3,b2,b1)

, so the pointer to b3() is the first and will be used.

Then you might have the following scenario. Let's start with state when patches
P1 and P2 are registered and enabled but the module M is not loaded. Then ftrace
ops for b() does not exist. Then we get into the following race:

CPU0					CPU1

load_module(M)

  complete_formation()

  mod->state = MODULE_STATE_COMING;
  mutex_unlock(&module_mutex);

					klp_register_patch(P3);
					klp_enable_patch(P3);

					# STATE 1

  klp_module_notify(M)
    klp_module_notify_coming(P1);
    klp_module_notify_coming(P2);
    klp_module_notify_coming(P3);

					# STATE 2

The ftrace ops for a() and b() then looks:

  STATE1:

	ops_a->func_stack -> list(a3,a2,a1);
	ops_b->func_stack -> list(b3);

  STATE2:
	ops_a->func_stack -> list(a3,a2,a1);
	ops_b->func_stack -> list(b2,b1,b3);

therefore, b2() is used for the module but a3() is used for vmcore
because they were the last added.

Example of the race with going modules:
=======================================

CPU0					CPU1

delete_module()  #SYSCALL

   try_stop_module()
     mod->state = MODULE_STATE_GOING;

   mutex_unlock(&module_mutex);

					klp_register_patch()
					klp_enable_patch()

					#save place to switch universe

					b()     # from module that is going
					  a()   # from core (patched)

   mod->exit();

Note that the function b() can be called until we call mod->exit().

If we do not apply patch against b() because it is in MODULE_STATE_GOING,
it will call patched a() with modified semantic and things might get wrong.

[jpoimboe@redhat.com: use one boolean instead of two]
Signed-off-by: NPetr Mladek <pmladek@suse.cz>
Acked-by: NJosh Poimboeuf <jpoimboe@redhat.com>
Acked-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Going over the virtio mmio code, I noticed that it doesn't correctly
access modern device config values using "natural" accessors: it uses
readb to get/set them byte by byte, while the virtio 1.0 spec explicitly states:

	4.2.2.2 Driver Requirements: MMIO Device Register Layout

	...

	The driver MUST only use 32 bit wide and aligned reads and writes to
	access the control registers described in table 4.1.
	For the device-specific configuration space, the driver MUST use
	8 bit wide accesses for 8 bit wide fields, 16 bit wide and aligned
	accesses for 16 bit wide fields and 32 bit wide and aligned accesses for
	32 and 64 bit wide fields.

Borrow code from virtio_pci_modern to do this correctly.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Fixes for KVM/ARM for 4.0-rc5.

Fixes page refcounting issues in our Stage-2 page table management code,
fixes a missing unlock in a gicv3 error path, and fixes a race that can
cause lost interrupts if signals are pending just prior to entering the
guest.

E1x chips (57710, 57711(E)) have no support for encapsulation
offload. bnx2x incorrectly advertises the support as available.

Setting of those features is conditional on "!CHIP_IS_E1x(bp)", but
the bp struct is not initialized yet at this point and consequently
any chip passes the check.
The check must use the "chip_is_e1x" local variable instead to work
correctly.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2015-03-16' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Here are a few fixes that I'd like to still get in:
 * disable U-APSD for better interoperability, from Michal Kazior
 * drop unencrypted frames in mesh forwarding, from Bob Copeland
 * treat non-QoS/WMM HT stations as non-HT, to fix confusion when
   they connect and then get QoS packets anyway due to HT
 * fix counting interfaces for combination checks, otherwise the
   interface combinations aren't properly enforced (from Andrei)
 * fix pure ECSA by reacting to the IE change
 * ignore erroneous (E)CSA to the current channel which sometimes
   happens due to AP/GO bugs
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
pull request (net): ipsec 2015-03-16

1) Fix the network header offset in _decode_session6
   when multiple IPv6 extension headers are present.
   From Hajime Tazaki.

2) Fix an interfamily tunnel crash. We set outer mode
   protocol too early and may dispatch to the wrong
   address family. Move the setting of the outer mode
   protocol behind the last accessing of the inner mode
   to fix the crash.

3) Most callers of xfrm_lookup() expect that dst_orig
   is released on error. But xfrm_lookup_route() may
   need dst_orig to handle certain error cases. So
   introduce a flag that tells what should be done in
   case of error. From Huaibin Wang.

Please pull or let me know if there are problems.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit [ef403edb: ALSA: hda - Don't access stereo amps for
mono channel widgets] fixed the handling of mono widgets in general,
but it still misses an exceptional case: namely, a mono mixer widget
taking a single stereo input.  In this case, it has stereo volumes
although it's a mono widget, and thus we have to take care of both
left and right input channels, as stated in HD-audio spec ("7.1.3
Widget Interconnection Rules").

This patch covers this missing piece by adding proper checks of stereo
amps in both the generic parser and the proc output codes.
Reported-by: NRaymond Yau <superquad.vortex2@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>