alc_subsystem_id() tries to pick up a headphone pin if not configured,
but this caused side-effects as the problem in commit
15870f05.

This patch fixes the driver behavior to pick up invalid HP pins; at least,
the pins that are listed as the primary outputs aren't taken any more.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

ASUS A7K needs additional GPIO1 bit setup; it has to be cleared.
Added a new fixup hook for this laptop so that it works as is.

Refernece: Novell bnc#494309
	http://bugzilla.novell.com/show_bug.cgi?id=494309Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The recent auto-parser doesn't work for machines with a single output
with ALC861, such as Toshiba laptops, because alc_subsystem_id() sets
the hp_pins[0] while it's listed in line_outs[0].
This ends up with the doubled initialization of the same mixer widget,
and it mutes the DAC route because hp_pins has no DAC assigned.

To fix this problem, just check spec->autocfg.hp_outs and speaker_outs
so that they are really detected pins.

Reference: Novell bnc#544161
	http://bugzilla.novell.com/show_bug.cgi?id=544161Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The auto-parser for ALC662/663/272 codecs doesn't work properly when
a speaker is connected to mono NID 0x17, and doesn't handle the dynamic
DAC assignment properly.

This patch fixes the issues and also improves the assignment of DACs
so that HP and speakers can have independent volume controls.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When the auto-mic switching between an analog and a digital mic is
needed with IDT codecs, the current driver doesn't reset the connection
of the digital mux.

This patch fixes the behavior by checking both mux connections properly.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Patch was tested on Toshiba NB200 and is found to enable sound.
Signed-off-by: NManoj Iyer <manoj.iyer@canonical.com>
Cc: stable@kernel.org
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

In the commit fdbc6626, I mistakenly
replaced the capture mixer array for ALC268_ACER to nosrc version
although this should be kept to alt_mixer.  Now fixed back.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Reference: ALSA bug #0004614
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=4614

port-A (0x11)      - front hp-out
port-D (0x12)      - rear line out
port-E (0x1c)      - front mic-in
port-F (0x16)      - Internal speakers
digital-mic (0x17) - Internal mic

init verbs, mixers, jack sensing and PCI_QUIRK to support this hardware
Signed-off-by: NMiguel de Barros <miguel.de.barros@bluewin.ch>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

BugLink: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=547994

Enable MSI by default for this Pavilion model.
Signed-off-by: NDaniel T Chen <crimsun@ubuntu.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

After puting a cd-audio inside my laptop there was no sound out here,
so I decided to install alsa-driver with debug level and setup a
model=test, it didn't help, but then I look at source code and added
this few lines, now cd-audio is working both when playback/recording.

[Additional minor fixes of mixer element/item names by tiwai]
Signed-off-by: NLukasz Marcinowski <nowymarluk@wp.pl>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The headphone and speaker mixer elements aren't properly set for
MSI GX620 with targa-8ch-dig quirk.
Also fixed the speaker volume control for other ALC883-targa quirks,
too.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The pin setup for Dell S14 quirk is rather wrong for the latest driver.
Fixed pin 0x0a, 0x0b, 0x0d and 0x0f.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Remove unnecessary (and buggy) init sequences left for IDT92HD83*
codecs in the previous fixes.  The DACs are now dynamically connected,
thus shouldn't be set statically in init verbs.  Also, the mono_nid
is detected dynamically, thus shouldn't be set staticaly, too.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add the quirk entry for HP dv6.  Also add a workaround for the headphone
detection by setting hp_detect=1 beforehand.  Without this, the driver
won't do auto-muting because BIOS doesn't give any HP pin but only a
line-out pin.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

It's possible that hp_detect is set even though no headphone pin is
detected.  The driver issues, however, an unsol event only to hp_pins[0],
which can be invalid.

This patch adds the check of the valid pin to send an unsol event
at initialization and resume callbacks.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

A smiliar fix for IDT 92HD71Bxx codecs like the previous commit for
other IDT/STAC codecs.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

IDT92HD73xx and STAC927x codecs use GPIO0 bit as EAPD on many machines.
However, currently we don't set it unless the model is specified just
for safety reason.  But, most machines do need this bit, so this safety
handling is rather annoying.

This patch enables GPIO0 setup as default for them.  Many HP / Dell
laptops should work even without model override with this change.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The HP laptops with ALC268 codec seem working better with model=auto
than model=toshiba; e.g. the auto model fixes missing digital outputs.
Let's fix quirk entry to choose auto model explicitly.
Tested-by: NJens Jorgensen <jbj1@ultraemail.net>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The model clevo-m540r was created with 6-channel and digital support. All
functions verified except spdif. Tested with a VIT D2000 laptop which has:

[lspci extract]
 Audio device [0403]: Intel Corporation 82801H (ICH8 Family) HD Audio
Controller [8086:284b] (rev 03)
        Subsystem: CLEVO/KAPOK Computer Device [1558:5409]

[/proc/asound/card0/codec\#0 header]
Codec: Realtek ALC883
Address: 0
Function Id: 0x1
Vendor Id: 0x10ec0883
Subsystem Id: 0x15585409
Revision Id: 0x100002

[Added a comment about HP mute and the model description by tiwai]
Signed-off-by: NDhionel Diaz <ddiaz@cenditel.gob.ve>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Added the quirk for Alienware M17x with IDT 92HD73* codec chip.
It has two HP and one line-out jack, one mic jack, a built-in
speaker and a built-in mic.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Due to the previous fix of input source for IDT92HD73xx, the amp mux
and amp vol stuff became unused.  Let's rip off dead codes.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fix the mux_nids to select directly the input source instead of mux
mixers so that it works with the current mux enum handler for IDT
92HD73xx codecs.

Also, clean up useless / unnecessary mixer controls and init verbs.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fix the old dead CONFIG_SND_DEBUG_DETECT to CONFIG_SND_DEBUG_VERBOSE.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Unmute the docking-station line-out as default on machines with
AD1984A codec chip.  It can be still muted via "Dock" mixer switch.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Added another entry for Nvidia HDMI device (10de:0003).

Reference: kernel bug#14097
	http://bugzilla.kernel.org/show_bug.cgi?id=14097Signed-off-by: NTakashi Iwai <tiwai@suse.de>

A similar initialization of GPIO1 pin like mobile model is needed
for laptop model, too.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add the support of automatic mute and mic-switching of the docking
station HP and mic plugs for AD1984A laptop model for some HP machines.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Conflicts:
	sound/pci/hda/patch_realtek.c

Fix the headphone pin routing of ALC268/ALC269 codecs.  Using alc882
routine doesn't work because alc268/alc269 parser assumes the
independent DACs for both HP and speaker outputs.  Need to assign the
DAC depending on the pin.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch fixes the wrong headphone output routing for MacBookPro 3,1/4,1
quirk with ALC889A codec, which caused the silent headphone output.
Also, this gives the individual Headphone and Speaker volume controls.

Reference: kernel bug#14078
	http://bugzilla.kernel.org/show_bug.cgi?id=14078Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>

In patch_vt1708(), the check of MUX nids is missing and this results in
the -EINVAL error in accessing Input Source mixer element.  Simpliy
adding the call of get_mux_nids() fixes the problem.

Reference: Novell bnc#534904
	https://bugzilla.novell.com/show_bug.cgi?id=534904Signed-off-by: NTakashi Iwai <tiwai@suse.de>

So far, the digital mic capture volume wasn't created.  This is because
IDT codecs have output amps for digital mics, not input amps, while
input amps should be used for other analog pins.  Thus the automatic
capture volume creation should check both directions for digital mics.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

More entries for HP laptops to get them working properly.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Signed-off-by: NTakashi Iwai <tiwai@suse.de>

1) Added support of internal subwoofer (it sounds!!!)
2) Auto muting front speakers and internal subwoofer on headphones plug.
3) Internal mic works.
4) 3 channel mods (jack maps):
       black  pink         blue
2ch: front   ext mic     line in
4ch: front   ext mic     surround
6ch: front   CLFE        surround
  Can be changed in mixer.
5) Sound can be recorded from:
 Internal mic
 Ext mic
 Cd
 Line in
6) 2 separate capture channels.
Signed-off-by: NDenis Kuplyakov <dener.kup@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The last patch in this series is for ALC662; pretty similar as the
previous patch for ALC861-VD.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

One more patch to give a better name for the primary output controls,
this time for ALC861-VD codec.  The change is simple, just checking the
pin connection whether it's a speaker-out.  When both speaker and HP
are assigned, we name the volume as "PCM" as this influences on both
outputs.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Similar improvements for ALC262 codec like previous two commits:
assign a better name, either Master or Speaker, for the primary output
controls.

However, in the case of ALC262 codec, the necessary changes are larger
than others because we need to check the possibility of different mixer
amps depending on the pins.  The pin 0x16 is mono, and bound with the
dedicated mixer 0x0e while other pins are bound with 0x0c.  Thus, there
are two possible volumes.

When only one of them is used, we can name it as "Master".  OTOH, when
both are used at the same time, they have to be named uniquely.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Instead of fixed "Front" mixer name, try to assign a better name, e.g.
"Master" or "Speaker" fot the primary output volume controls of ALC260
codec.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>