when system suspend, need to set pins to low power state to
save IO power consumption, there are three states of pinctrl:
"default", "idle" and "sleep". Currently enet supports default
and sleep state.
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

In case the bootloader has incorrectly configured the ALT mode of
MX6SL_PAD_ECSPI1_SS0 pad, we end up with the following probe error:

m25p80 spi0.0: found mr25h256, expected m25p32
m25p80 spi0.0: mr25h256 (32 Kbytes)

In order to avoid this issue, add an entry for MX6SL_PAD_ECSPI1_SS0 pad, so
that kernel configures the ECSPI chip select as GPIO functionality, which
results in correct SPI NOR probe.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@freescale.com>

On imx6sl-evk board the VGEN1 regulator powers up the NVCC_1P2V domain of the
imx6sl SoC, so we need to keep it always powered.

According to imx6sl datasheet the GPIO block has three supplies:
NVCC33_IO, NVCC18_IO and NVCC_1P2V and it states that:
"All digital I/O supplies (NVCC_xxxx) must be powered under normal conditions
whether the associated I/O pins are in use or not"

This problem has been observed by the fact that a GPIO connected to an LED could
not work when the PMIC driver was enabled.

Keeping VGEN1 regulator always enabled fixes the problem.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

GPIO3_20 is connected to a debug LED.

Add support for it.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

imx6sl-evk has a wm8962 codec. Add support for it.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

imx6sl-evk board has Freescale PFUZE100 regulator, so add support for it.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

i.MX6SL EVK board has a 3*3 keypad matrix to support 8 keypads,
enable them, the keymap is as below:

SW6:  MATRIX_KEY(0x0, 0x0, KEY_UP)         /* ROW0, COL0 */
SW7:  MATRIX_KEY(0x0, 0x1, KEY_DOWN)       /* ROW0, COL1 */
SW8:  MATRIX_KEY(0x0, 0x2, KEY_ENTER)      /* ROW0, COL2 */
SW9:  MATRIX_KEY(0x1, 0x0, KEY_HOME)       /* ROW1, COL0 */
SW10: MATRIX_KEY(0x1, 0x1, KEY_RIGHT)      /* ROW1, COL1 */
SW11: MATRIX_KEY(0x1, 0x2, KEY_LEFT)       /* ROW1, COL2 */
SW12: MATRIX_KEY(0x2, 0x0, KEY_VOLUMEDOWN) /* ROW2, COL0 */
SW13: MATRIX_KEY(0x2, 0x1, KEY_VOLUMEUP)   /* ROW2, COL1 */
Signed-off-by: NAnson Huang <b20788@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

The device tree specification recommends that generic name should be
used for nodes.  So instead of naming those fixed regulator nodes
arbitrarily, let's use the generic name 'regulator@num' for those nodes.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Currently, all pinctrl setting nodes are defined in <soc>.dtsi, so that
boards that share the same pinctrl setting do not have to define it time
and time again in <board>.dts.  However, along with the devices and use
cases being added continuously, the pinctrl setting nodes under iomuxc
becomes more than expected.  This bloats device tree blob for particular
board unnecessarily since only a small subset of those pinctrl setting
nodes will be used by the board.  It impacts not only the DTB file size
but also the run-time device tree lookup efficiency.

The patch moves all the pinctrl data into individual boards as needed.
With the changes, the pinctrl setting nodes becomes local to particular
board, and it makes no sense to continue numbering the setting for
given peripheral.  Thus, all the pinctrl phandler name gets updated to
have only peripheral name in there.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

enable the spi nor for imx6sl-evk boards.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This is needed for SD3.0 cards working on UHS mode.
Signed-off-by: NDong Aisheng <b29396@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Enable USB function for OTG 1 and OTG 2 at mx6sololite evk.
Besides, fix the wrong interrupt number for OTG2 and host 1.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Add initial imx6sl-evk board support with uart, usdhc and fec enabled.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>