This patch (as1283) adds a new flag, USBDEVFS_URB_BULK_CONTINUATION,
to usbfs.  It is intended for userspace libraries such as libusb and
openusb.  When they have to break up a single usbfs bulk transfer into
multiple URBs, they will set the flag on all but the first URB of the
series.

If an error other than an unlink occurs, the kernel will automatically
cancel all the following URBs for the same endpoint and refuse to
accept new submissions, until an URB is encountered that is not marked
as a BULK_CONTINUATION.  Such an URB would indicate the start of a new
transfer or the presence of an older library, so the kernel returns to
normal operation.

This enables libraries to delimit bulk transfers correctly, even in
the presence of early termination as indicated by short packets.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The previous code had a bug that would add a trailing null byte to
the returned descriptor.
Signed-off-by: NGeorge Spelvin <linux@horizon.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

usb_buffer_map_sg should return negative on error according to
its documentation. But dma_map_sg returns 0 on error. Take this
into account and return -ENOMEM in such situation.

While at it, return -EINVAL instead of -1 when wrong input is
passed in.

If this wasn't done, usb_sg_* operations used after usb_sg_init
which returned 0 may cause oopses/deadlocks since we don't init
structures/entries, esp. completion and status entry.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The current limit only allows isochronous transfers up to 32kbyte/urb,
updating this to 192 kbyte/urb improves the reliability of the
transfer. USB 2.0 transfer is possible with 32kbyte but increases the
chance of corrupted/incomplete data when the system is performing some
other tasks in the background.

http://www.spinics.net/lists/linux-usb/msg19955.htmlSigned-off-by: NMarkus Rechberger <mrechberger@gmail.com>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1268) changes the way usbcore handles child devices that
undergo a disconnection and reconnection while the parent hub is
suspended.  Currently, if the child isn't enabled for remote wakeup we
leave it alone, figuring that it will go through a reset-resume when
somebody tries to use it.

However this isn't a good approach if the reason for the disconnection
is that the child decided to switch modes or in some other way alter
its descriptors.  In that case we want to re-enumerate it as soon as
possible, not wait until somebody forces a reset-resume.

To resolve the issue, this patch treats reconnected suspended child
devices as though they had requested a remote wakeup, even if they
weren't enabled for it.  The mode switch or descriptor change will be
detected during the reset part of the reset-resume, and the device
will be re-enumerated immediately.

The disadvantage of this change is that it will cause autosuspended
devices to be resumed when the computer wakes up from a system sleep
during which the root hub was reset or lost power.  This shouldn't
matter much; some people would even argue that autosuspended devices
should _always_ be resumed when the system wakes up!
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: N"Yang Fei-AFY095" <fei.yang@motorola.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1267) changes usb_kick_khubd() and hdev_to_hub() to make
them more resilient against situations where a hub device isn't bound
to the hub driver.  The code assumes that if a root hub was
successfully registered then it must be bound to the hub driver.

But this assumption can fail if the user manually unbinds the hub
driver, or more importantly, if the host controller dies causing
usb_set_configuration to fail.

To protect against these possibilities, make hdev_to_hub() check that
the hub device is configured before dereferencing the active
configuration, and make usb_kick_khubd() check that the pointer to the
hub's private data structure isn't NULL.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1261) reduces the amount of detailed URB information
logged by usbfs when the usbfs_snoop parameter is enabled.

Currently we don't display the final status value for a completed URB.
But we do display the entire data buffer twice: both before submission
and after completion.  The after-completion display doesn't limit
itself to the actual_length value.  But since usbmon is readily
available in virtually all distributions, there's no reason for usbfs
to print out any buffer contents at all!

So this patch restricts the information to: userspace buffer pointer,
endpoint number, type, and direction, length or actual_length, and
timeout value or status.  Now everything fits neatly into a single
line.

Along with those changes, the patch also fixes the snoop output for
the REAPURBNDELAY and REAPURBNDELAY32 ioctls.  The current version
omits the 'N' from the names.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1260) changes the pm_usage_cnt field in struct
usb_interface from an int to an atomic_t.  This is so that drivers can
invoke the usb_autopm_get_interface_async() and
usb_autopm_put_interface_async() routines without locking and without
fear of corrupting the pm_usage_cnt value.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1258) implements a feature that users have been asking
for: It gives programs the ability to "claim" a port on a hub, via a
new usbfs ioctl.  A device plugged into a "claimed" port will not be
touched by the kernel beyond the immediate necessities of
initialization and enumeration.

In particular, when a device is plugged into a "claimed" port, the
kernel will not select and install a configuration.  And when a config
is installed by usbfs or sysfs, the kernel will not probe any drivers
for any of the interfaces.  (However the kernel will fetch various
string descriptors during enumeration.  One could argue that this
isn't really necessary, but the strings are exported in sysfs.)

The patch does not guarantee exclusive access to these devices; it is
still possible for more than one program to open the device file
concurrently.  Programs are responsible for coordinating access among
themselves.

A demonstration program showing how to use the new interface can be 
found in an attachment to

	http://marc.info/?l=linux-usb&m=124345857431452&w=2

The patch also makes a small simplification to the hub driver,
replacing a bunch of more-or-less useless variants of "out of memory"
with a single message.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This fix permits the "new" usbmon to access usb-storage's data buffer
without DMA remapping tricks. It should be compatible with PIO controllers
and not add any new crashes. Note that from now on PIO controllers and
usbmon are uniform in their access pattern and if one crashes then
the other will too. Hopefuly neither does.

As a side effect, we get rid for #ifdefs, which were a little ugly.
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When there's a descriptor after the SuperSpeed endpoint companion
descriptor, the previous code would have skipped over twice the length it
was supposed to.  This code fixes crashes seen with UASP devices (which
have a UASP descriptor after the SS endpoint companion descriptor).
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This allows subsytems to provide devtmpfs with non-default permissions
for the device node. Instead of the default mode of 0600, null, zero,
random, urandom, full, tty, ptmx now have a mode of 0666, which allows
non-privileged processes to access standard device nodes in case no
other userspace process applies the expected permissions.

This also fixes a wrong assignment in pktcdvd and a checkpatch.pl complain.
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Let attribute group vectors be declared "const".  We'd
like to let most attribute metadata live in read-only
sections... this is a start.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1272) changes the error code returned when an open call
for a USB device node fails to locate the corresponding device.  The
appropriate error code is -ENODEV, not -ENOENT.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: Kay Sievers <kay.sievers@vrfy.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

access_ok() checks must be done on every part of the userspace structure
that is accessed. If access_ok() on one part of the struct succeeded, it
does not imply it will succeed on other parts of the struct. (Does
depend on the architecture implementation of access_ok()).

This changes the __get_user() users to first check access_ok() on the
data structure.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Cc: stable <stable@kernel.org>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

usb_parse_ss_endpoint_companion() was supposed to allocate a structure to
hold the SuperSpeed Endpoint Companion descriptor, and either copy the
values the device returned, or fill in default values if the device
descriptor did not include the companion descriptor.

However, the previous code would miss the last endpoint in a configuration
with no descriptors after it.  Make usb_parse_endpoint() allocate the SS
endpoint companion descriptor and fill it with default values, even if
we've run out of buffer space in this configuration descriptor.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1262) fixes a bug in usbfs: It refuses to accept
zero-length transfers, and it insists that the buffer pointer be valid
even if there is no data being transferred.

The patch also consolidates a bunch of repetitive access_ok() checks
into a single check, which incidentally fixes the lack of such a check
for Isochronous URBs.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

commit b7af0bb2 ("USB: allow malformed LANGID descriptors") broke support
for devices without string descriptor support.

Reporting string descriptors is optional to USB devices, and a device
lets us know it can't deal with strings by responding to the LANGID
request with a STALL token.

The kernel handled that correctly before b7af0bb2 came in, but failed
hard if the LANGID was reported but broken. More than that, if a device
was not able to provide string descriptors, the LANGID was retrieved
over and over again at each string read request.

This patch changes the behaviour so that

 a) the LANGID is only queried once
 b) devices which can't handle string requests are not asked again
 c) devices with malformed LANGID values have a sane fallback to 0x0409
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

this fixes a race between async_completed() and proc_reapurbnonblock().

CPU A                   CPU B

spin_lock(&ps->lock);
list_move_tail(&as->asynclist, &ps->async_completed);
spin_unlock(&ps->lock);

                                if (!(as = async_getcompleted(ps)))
                                        return -EAGAIN;
                                return processcompl(as, (void __user * __user *)arg);

processcompl() calls free_async() which calls kfree(as)

as->status = urb->status;
if (as->signr) {
        sinfo.si_signo = as->signr;
        sinfo.si_errno = as->status;
        sinfo.si_code = SI_ASYNCIO;
        sinfo.si_addr = as->userurb;
        kill_pid_info_as_uid(as->signr, &sinfo, as->pid, as->uid,
                              as->euid, as->secid);
}
snoop(&urb->dev->dev, "urb complete\n");
snoop_urb(urb, as->userurb);

write after kfree
Signed-off-by: NOliver Neukum <oliver@neukum.org>

This reverts commit cc71329b, so that
Red Hat machines can boot properly.  It seems that the Red Hat initrd
code tries to watch the /proc/bus/usb/devices file to monitor usb
devices showing up.  While this task is prone to lots of races and does
not show the true state of the system, they seem to like it.

So for now, don't move this option under the EMBEDDED config option.


Cc: Scott James Remnant <scott@canonical.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Jeff Chua <jeff.chua.linux@gmail.com>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Added descriptions (for WIRELESS_CONTROLLER and MISC) were taken from
the usb-devices script now included in usbutils.

Also sort the classes in the same order as in include/linux/usb/ch9.h
for easier comparison for future updates.
Signed-off-by: NFrans Pop <elendil@planet.nl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes a memory leak in devio.c::processcompl

If writing to user space fails the packet must be discarded, as it
already has been removed from the queue of completed packets.
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1255) updates the interface for calling
usb_hub_clear_tt_buffer().  Even the name of the function is changed!

When an async URB (i.e., Control or Bulk) going through a high-speed
hub to a non-high-speed device is cancelled or fails, the hub's
Transaction Translator buffer may be left busy still trying to
complete the transaction.  The buffer has to be cleared; that's what
usb_hub_clear_tt_buffer() does.

It isn't safe to send any more URBs to the same endpoint until the TT
buffer is fully clear.  Therefore the HCD needs to be told when the
Clear-TT-Buffer request has finished.  This patch adds a callback
method to struct hc_driver for that purpose, and makes the hub driver
invoke the callback at the proper time.

The patch also changes a couple of names; "hub_tt_kevent" and
"tt.kevent" now look rather antiquated.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Commit 5fd29d6c ("printk: clean up
handling of log-levels and newlines") changed printk semantics.  printk
lines with multiple KERN_<level> prefixes are no longer emitted as
before the patch.

<level> is now included in the output on each additional use.

Remove all uses of multiple KERN_<level>s in formats.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Replace if-elseif-else with switch-case
to keep the code consistent which is semantically same

Switch-case is used here,
http://www.spinics.net/lists/linux-usb/msg17201.html
Making consistent at other places in usb/core

Also easier to read and maintain when USB4.0, 5.0, ... comes
Signed-off-by: NViral Mehta <viral.mehta@einfochips.com>
Tested-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Differentiate between SuperSpeed endpoint companion descriptor and the
wireless USB endpoint companion descriptor.  Make all structure names for
this descriptor have "ss" (SuperSpeed) in them.  David Vrabel asked for
this change in http://marc.info/?l=linux-usb&m=124091465109367&w=2Reported-by: NDavid Vrabel <david.vrabel@csr.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is the original patch I created before David Vrabel posted a better
patch (http://marc.info/?l=linux-usb&m=123377477209109&w=2) that does
basically the same thing.  This patch will get replaced with his
(modified) patch later.

Allow USB device drivers that use usb_sg_init() and usb_sg_wait() to push
bulk endpoint scatter gather lists down to the host controller drivers.
This allows host controller drivers to more efficiently enqueue these
transfers, and allows the xHCI host controller to better take advantage of
USB 3.0 "bursts" for bulk endpoints.

This patch currently only enables scatter gather lists for bulk endpoints.
Other endpoint types that use the usb_sg_* functions will not have their
scatter gather lists pushed down to the host controller.  For periodic
endpoints, we want each scatterlist entry to be a separate transfer.
Eventually, HCDs could parse these scatter-gather lists for periodic
endpoints also.  For now, we use the old code and call usb_submit_urb()
for each scatterlist entry.

The caller of usb_sg_init() can request that all bytes in the scatter
gather list be transferred by passing in a length of zero.  Handle that
request for a bulk endpoint under xHCI by walking the scatter gather list
and calculating the length.  We could let the HCD handle a zero length in
this case, but I'm not sure if the core layers in between will get
confused by this.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Originally, the USB core had no support for allocating bandwidth when a
particular configuration or alternate setting for an interface was
selected.  Instead, the device driver's URB submission would fail if
there was not enough bandwidth for a periodic endpoint.  Drivers could
work around this, by using the scatter-gather list API to guarantee
bandwidth.

This patch adds host controller API to allow the USB core to allocate or
deallocate bandwidth for an endpoint.  Endpoints are added to or dropped
from a copy of the current schedule by calling add_endpoint() or
drop_endpoint(), and then the schedule is atomically evaluated with a
call to check_bandwidth().  This allows all the endpoints for a new
configuration or alternate setting to be added at the same time that the
endpoints from the old configuration or alt setting are dropped.

Endpoints must be added to the schedule before any URBs are submitted to
them.  The HCD must be allowed to reject a new configuration or alt
setting before the control transfer is sent to the device requesting the
change.  It may reject the change because there is not enough bandwidth,
not enough internal resources (such as memory on an embedded host
controller), or perhaps even for security reasons in a virtualized
environment.

If the call to check_bandwidth() fails, the USB core must call
reset_bandwidth().  This causes the schedule to be reverted back to the
state it was in just after the last successful check_bandwidth() call.

If the call succeeds, the host controller driver (and hardware) will have
changed its internal state to match the new configuration or alternate
setting.  The USB core can then issue a control transfer to the device to
change the configuration or alt setting.  This allows the core to test new
configurations or alternate settings before unbinding drivers bound to
interfaces in the old configuration.

WIP:

The USB core must add endpoints from all interfaces in a configuration
to the schedule, because a driver may claim that interface at any time.
A slight optimization might be to add the endpoints to the schedule once
a driver claims that interface.  FIXME

This patch does not cover changing alternate settings, but it does
handle a configuration change or de-configuration.  FIXME

The code for managing the schedule is currently HCD specific.  A generic
scheduling algorithm could be added for host controllers without
built-in scheduling support.  For now, if a host controller does not
define the check_bandwidth() function, the call to
usb_hcd_check_bandwidth() will always succeed.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The USB 3.0 bus specification added an "Endpoint Companion" descriptor that is
supposed to follow all SuperSpeed Endpoint descriptors.  This descriptor is used
to extend the bus protocol to allow more packets to be sent to an endpoint per
"microframe".  The word microframe was removed from the USB 3.0 specification
because the host controller does not send Start Of Frame (SOF) symbols down the
USB 3.0 wires.

The descriptor defines a bMaxBurst field, which indicates the number of packets
of wMaxPacketSize that a SuperSpeed device can send or recieve in a service
interval.  All non-control endpoints may set this value as high as 16 packets
(bMaxBurst = 15).

The descriptor also allows isochronous endpoints to further specify that they
can send and receive multiple bursts per service interval.  The bmAttributes
allows them to specify a "Mult" of up to 3 (bmAttributes = 2).

Bulk endpoints use bmAttributes to report the number of "Streams" they support.
This was an extension of the endpoint pipe concept to allow multiple mass
storage device commands to be outstanding for one bulk endpoint at a time.  This
should allow USB 3.0 mass storage devices to support SCSI command queueing.
Bulk endpoints can say they support up to 2^16 (65,536) streams.

The information in the endpoint companion descriptor must be stored with the
other device, config, interface, and endpoint descriptors because the host
controller needs to access them quickly, and we need to install some default
values if a SuperSpeed device doesn't provide an endpoint companion descriptor.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add host controller driver API and a slot_id variable to struct
usb_device.  This allows the xHCI host controller driver to ask the
hardware to allocate a slot for the device when a struct usb_device is
allocated.  The slot needs to be allocated at that point because the
hardware can run out of internal resources, and we want to know that very
early in the device connection process.  Don't call this new API for root
hubs, since they aren't real devices.

Add HCD API to let the host controller choose the device address.  This is
especially important for xHCI hardware running in a virtualized
environment.  The guests running under the VM don't need to know which
addresses on the bus are taken, because the hardware picks the address for
them.  Announce SuperSpeed USB devices after the address has been assigned
by the hardware.

Don't use the new get descriptor/set address scheme with xHCI.  Unless
special handling is done in the host controller driver, the xHC can't
issue control transfers before you set the device address.  Support for
the older addressing scheme will be added when the xHCI driver supports
the Block Set Address Request (BSR) flag in the Address Device command.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds a hex route string to each USB device.  The route string is used
by the USB 3.0 host controller to send packets through the device tree.  USB 3.0
hubs use this string to route packets to the correct port.  This is fundamental
bus change from USB 2.0, where all packets were broadcast across the bus.

Devices (including hubs) under a root port receive the route string 0x0.  Every
four bits in the route string represent a port on a hub.  This length works
because USB 3.0 hubs are limited to 15 ports, and USB 2.0 hubs (with potentially
more ports) will never see packets with a route string.  A port number of 0
means the packet is destined for that hub.

For example, a peripheral device might have a route string of 0x00097.
This means the device is connected to port 9 of the hub at depth 1.
The hub at depth 1 is connected to port 7 of a hub at depth 0.
The hub at depth 0 is connected to a root port.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The USB 3.0 bus specification defines a new connection sequence for USB 3.0
hubs and roothubs.  USB 3.0 devices are reset and link trained by the hub
before the port status change notification is sent to the host OS.  This means
that an entire tree of devices can be trained in parallel on power up, and the
OS no longer needs to reset USB 3.0 devices.  Change the USB core's hub port
init sequence so that it does not reset USB 3.0 devices.

The port status change from the roothub and from the USB 3.0 hub will report
the SuperSpeed connect correctly.  This patch currently only handles the
roothub case.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add USB 3.0 root hub descriptors.  This is a kludge because I reused the old
USB 2.0 descriptors, instead of using the new USB 3.0 hub descriptors with
endpoint companion descriptors and other descriptors.  I did this because I
wasn't ready to add USB 3.0 hub changes to khubd.  For now, a USB 3.0 roothub
looks like a USB 2.0 roothub, with a higher speed.

USB 3.0 hubs have no transaction translator (TT).

Make USB core debugging handle super speed ports.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Modify the USB core to handle the new USB 3.0 speed, "SuperSpeed".  This
is 5.0 Gbps (wire speed).  There are probably more places that check for
speed that I've missed.

SuperSpeed devices have a 512 byte endpoint 0 max packet size.  This shows
up as a bMaxPacketSize0 set to 0x09 (see table 9-8 of the USB 3.0 bus
spec).

xHCI spec says that the xHC can handle intervals up to 2^15 microframes.  That
might change when real silicon becomes available.

Add FIXME note for SuperSpeed isochronous endpoints.  They can transmit up
to 16 packets in one "burst" before they wait for an acknowledgment of the
packets.  They can do up to 3 bursts per microframe (determined by the
mult value in the endpoint companion descriptor).  The xHCI driver doesn't
have support for isoc yet, so fix this later.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add PCI initialization code to take control of the xHCI host controller
away from the BIOS, halt, and reset the host controller.  The xHCI spec
says that BIOSes must give up the host controller within 5 seconds.

Add some host controller glue functions to handle hardware initialization
and memory allocation for the host controller.  The current xHCI
prototypes use PCI interrupts, but the xHCI spec requires MSI-X
interrupts.  Add code to support MSI-X interrupts, but use the PCI
interrupts for now.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Currently if a laptop is suspended e.g. while docked and then resumed after
undocking it, the following errors get generated because the USB hub in the
docking station and the devices connected to it are no longer available:
pm_op(): usb_dev_resume+0x0/0x10 returns -19
PM: Device 1-2 failed to resume: error -19
pm_op(): usb_dev_resume+0x0/0x10 returns -19
PM: Device 1-2.2 failed to resume: error -19
pm_op(): usb_dev_resume+0x0/0x10 returns -19
PM: Device 1-2.3 failed to resume: error -19

As the removal of USB devices while a system is suspended is a relatively
common use case and in most cases not an error, just return success on
-ENODEV. The user gets informed anyway as the USB subsystem generates
regular disconnect messages for the devices shortly afterwards:
usb 1-2: USB disconnect, address 3
usb 1-2.2: USB disconnect, address 4
usblp0: removed
usb 1-2.3: USB disconnect, address 5
Signed-off-by: NFrans Pop <elendil@planet.nl>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This replaces dma_sync_single() and dma_sync_sg() with
dma_sync_single_for_cpu() and dma_sync_sg_for_cpu() respectively
because they is an obsolete API; include/linux/dma-mapping.h says:

/* Backwards compat, remove in 2.7.x */
#define dma_sync_single		dma_sync_single_for_cpu
#define dma_sync_sg		dma_sync_sg_for_cpu
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The endpoint devices look like simple attribute groups now, and no longer
like devices with a specific subsystem. They will also no longer emit uevents.

It also removes the device node requests for endpoint devices, which are not
implemented for now.
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1237) changes the way the PCI host controller drivers
avoid retaining bogus hardware states during resume-from-hibernation.
Previously we had reset the hardware as part of preparing to reinstate
the memory image.  But we can do better now with the new PM framework,
since we know exactly which resume operations are from hibernation.

The pci_resume method is changed to accept a flag indicating whether
the system is resuming from hibernation.  When this flag is set, the
drivers will reset the hardware to get rid of any existing state.

Similarly, the pci_suspend method is changed to remove the
pm_message_t argument.  It's no longer needed, since no special action
has to be taken when preparing to reinstate the memory image.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>