It was reported that after resuming from suspend network fails with
error "do_IRQ: 3.38 No irq handler for vector", see [0]. Enabling WoL
can work around the issue, but the only actual fix is to disable MSI.
So let's mimic the behavior of the vendor driver and disable MSI on
all chip versions before RTL8168d.

[0] https://bugzilla.kernel.org/show_bug.cgi?id=204079

Fixes: 6c6aa15f ("r8169: improve interrupt handling")
Reported-by: NDušan Dragić <dragic.dusan@gmail.com>
Tested-by: NDušan Dragić <dragic.dusan@gmail.com>
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit a6851c61.
It was reported that RTL8111b successfully finishes 1000/Full autoneg
but no data flows. Reverting the original patch fixes the issue.
It seems to be a HW issue with the integrated RTL8211B PHY. This PHY
version used also e.g. on RTL8168d, so better revert the original patch.
Reported-by: NBernhard Held <berny156@gmx.de>
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The udp_ip4_ind bit is set only for IPv4 UDP non-fragmented packets
so that the hardware can flip the checksum to 0xFFFF if the computed
checksum is 0 per RFC768.

However, this bit had to be set for IPv6 UDP non fragmented packets
as well per hardware requirements. Otherwise, IPv6 UDP packets
with computed checksum as 0 were transmitted by hardware and were
dropped in the network.

In addition to setting this bit for IPv6 UDP, the field is also
appropriately renamed to udp_ind as part of this change.

Fixes: 5eb5f860 ("net: qualcomm: rmnet: Add support for TX checksum offload")
Cc: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: NSubash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make sure the delayed work for stats update is not pending before
wq destruction.
This fixes the module unload path.
The issue is there since day 1.

Fixes: a556c76a ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: NClaudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The hw_ver field was initialized to zero. Return the chip revision.
This is relevant for rdma driver.
Signed-off-by: NMichal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 3968d389 ("bnx2x: Fix Multi-Cos.") which enabled multi-cos
feature after prolonged time in driver added some regression causing
numerous issues (sudden reboots, tx timeout etc.) reported by customers.
We plan to backout this commit and submit proper fix once we have root
cause of issues reported with this feature enabled.

Fixes: 3968d389 ("bnx2x: Fix Multi-Cos.")
Signed-off-by: NSudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: NManish Chopra <manishc@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Align to the naming convention in TLS documentation.

Fixes: 51a5e563 ("nfp: tls: add basic statistics")
Suggested-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

A netdev mismatch in the processed TLS SKB should not occur,
and indicates a kernel bug.
Add WARN_ONCE to spot such cases.

Fixes: d2ead1f3 ("net/mlx5e: Add kTLS TX HW offload support")
Suggested-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

This patch prevents a race between user invoked cached counters
query and a neighbor last usage updater.

The cached flow counter stats can be queried by calling
"mlx5_fc_query_cached" which provides the number of bytes and
packets that passed via this flow since the last time this counter
was queried.
It does so by reducting the last saved stats from the current, cached
stats and then updating the last saved stats with the cached stats.
It also provide the lastuse value for that flow.

Since "mlx5e_tc_update_neigh_used_value" needs to retrieve the
last usage time of encapsulation flows, it calls the flow counter
query method periodically and async to user queries of the flow counter
using cls_flower.
This call is causing the driver to update the last reported bytes and
packets from the cache and therefore, future user queries of the flow
stats will return lower than expected number for bytes and packets
since the last saved stats in the driver was updated async to the last
saved stats in cls_flower.

This causes wrong stats presentation of encapsulation flows to user.

Since the neighbor usage updater only needs the lastuse stats from the
cached counter, the fix is to use a dedicated lastuse query call that
returns the lastuse value without synching between the cached stats and
the last saved stats.

Fixes: f6dfb4c3 ("net/mlx5e: Update neighbour 'used' state using HW flow rules counters")
Signed-off-by: NAriel Levkovich <lariel@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Speed translation is performed based on legacy or extended PTYS
register. Translate speed with respect to:
1) Capability bit of extended PTYS table.
2) User request:
 a) When auto-negotiation is turned on, inspect advertisement whether it
 contains extended link modes.
 b) When auto-negotiation is turned off, speed > 100Gbps (maximal
 speed supported in legacy mode).
With both conditions fulfilled translation is done with extended PTYS
table otherwise use legacy PTYS table.
Without this patch 25/50/100 Gbps speed cannot be set, since try to
configure in extended mode but read from legacy mode.

Fixes: dd1b9e09 ("net/mlx5: ethtool, Allow legacy link-modes configuration via non-extended ptys")
Signed-off-by: NAya Levin <ayal@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

No XSK support in the enhanced IPoIB driver and representors.
Add a profile property to specify this, and enhance the logic
that calculates the max number of channels to take it into
account.

Fixes: db05815b ("net/mlx5e: Add XSK zero-copy support")
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

New flow table type RDMA_RX was added but the MLX5_CAP_FLOW_TABLE_TYPE
didn't handle this new flow table type.
This means that MLX5_CAP_FLOW_TABLE_TYPE returns an empty capability to
this flow table type.

Update both the macro and the maximum supported flow table type to
RDMA_RX.

Fixes: d83eb50e ("net/mlx5: Add support in RDMA RX steering")
Signed-off-by: NMaor Gottlieb <maorg@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

When lag is active, which is controlled by the bonded mlx5e netdev, mlx5
interface unregestering must happen in the reverse order where rdma is
unregistered (unloaded) first, to guarantee all references to the lag
context in hardware is removed, then remove mlx5e netdev interface which
will cleanup the lag context from hardware.

Without this fix during destroy of LAG interface, we observed following
errors:
 * mlx5_cmd_check:752:(pid 12556): DESTROY_LAG(0x843) op_mod(0x0) failed,
   status bad parameter(0x3), syndrome (0xe4ac33)
 * mlx5_cmd_check:752:(pid 12556): DESTROY_LAG(0x843) op_mod(0x0) failed,
   status bad parameter(0x3), syndrome (0xa5aee8).

Fixes: a31208b1 ("net/mlx5_core: New init and exit flow for mlx5_core")
Reviewed-by: NParav Pandit <parav@mellanox.com>
Reviewed-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NMark Zhang <markz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

fm_set_max_frm() existed in the Freescale SDK as a callback for an
early_param. When this code was ported to the upstream kernel the
early_param was converted to a module_param making the reference to the
function incorrect. The rest of the comment already does a good job of
explaining the parameter so removing the reference to the non-existent
function seems like the best thing to do.
Signed-off-by: NChris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While using net_dim, a dim_sample was used without ever initializing the
comps value. Added use of DIV_ROUND_DOWN_ULL() to prevent potential
overflow, it should not be a problem to save the final result in an int
because after the division by epms the value should not be larger than a
few thousand.

[ 1040.127124] UBSAN: Undefined behaviour in lib/dim/dim.c:78:23
[ 1040.130118] signed integer overflow:
[ 1040.131643] 134718714 * 100 cannot be represented in type 'int'

Fixes: 398c2b05 ("linux/dim: Add completions count to dim_sample")
Signed-off-by: NYamin Friedman <yaminf@mellanox.com>
Signed-off-by: NLeon Romanovsky <leonro@mellanox.com>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the custom implementation with fwnode_get_mac_address,
which works on both DT and ACPI platforms.

While here, replace memcpy() by ether_addr_copy().
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The onboard sky2 NIC on ASUS P6T WS PRO doesn't work after PM resume
due to the infamous IRQ problem.  Disabling MSI works around it, so
let's add it to the blacklist.

Unfortunately the BIOS on the machine doesn't fill the standard
DMI_SYS_* entry, so we pick up DMI_BOARD_* entries instead.

BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1142496Reported-and-tested-by: NMarcus Seyfarth <m.seyfarth@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit f4e5f775.

Andrew Lunn says this should be handled another way.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some glue logic drivers support 1G without having GMAC/GMAC4/XGMAC.

Let's allow this speed by default.
Reported-by: NOndrej Jirman <megi@xff.cz>
Tested-by: NOndrej Jirman <megi@xff.cz>
Fixes: 5b0d7d7d ("net: stmmac: Add the missing speeds that XGMAC supports")
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need the memory to be zeroed upon allocation so use kcalloc()
instead.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RX Descriptors are being cleaned after setting the buffers which may
lead to buffer addresses being wiped out.

Fix this by clearing earlier the RX Descriptors.

Fixes: 2af6106a ("net: stmmac: Introducing support for Page Pool")
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit(net: phy: marvell: change default m88e1510 LED configuration),
the active LED of Hip07 devices is always off, because Hip07 just
use 2 LEDs.
This patch adds a phy_register_fixup_for_uid() for m88e1510 to
correct the LED configuration.

Fixes: 07777246 ("net: phy: marvell: change default m88e1510 LED configuration")
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Reviewed-by: Nlinyunsheng <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PPv2's XLGMAC can wait for 3 idle frames before triggering a link up
event. This can cause the link to be stuck low when there's traffic on
the interface, so disable this feature.

Fixes: 4bb04326 ("net: mvpp2: phylink support")
Signed-off-by: NMaxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 8c0d3a02 ("PCI: Add accessors for PCI Express Capability")
added accessors for the PCI Express Capability so that drivers didn't
need to be aware of differences between v1 and v2 of the PCI
Express Capability.

Replace pci_read_config_word() and pci_write_config_word() calls with
pcie_capability_read_word() and pcie_capability_write_word().
Signed-off-by: NFrederick Lawler <fred@fredlawl.com>
Acked-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 8c0d3a02 ("PCI: Add accessors for PCI Express Capability")
added accessors for the PCI Express Capability so that drivers didn't
need to be aware of differences between v1 and v2 of the PCI
Express Capability.

Replace pci_read_config_word() and pci_write_config_word() calls with
pcie_capability_read_word() and pcie_capability_write_word().
Signed-off-by: NFrederick Lawler <fred@fredlawl.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 8c0d3a02 ("PCI: Add accessors for PCI Express Capability")
added accessors for the PCI Express Capability so that drivers didn't
need to be aware of differences between v1 and v2 of the PCI
Express Capability.

Replace pci_read_config_word() and pci_write_config_word() calls with
pcie_capability_read_word() and pcie_capability_write_word().
Signed-off-by: NFrederick Lawler <fred@fredlawl.com>
Reviewed-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As pointed out by Firo Yang, a netdev tx timeout may trigger just before an
ethtool set_channels operation is started. be_tx_timeout(), which dumps
some queue structures, is not written to run concurrently with
be_update_queues(), which frees/allocates those queues structures. Add some
synchronization between the two.

Message-id: <CH2PR18MB31898E033896F9760D36BFF288C90@CH2PR18MB3189.namprd18.prod.outlook.com>
Signed-off-by: NBenjamin Poirier <bpoirier@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes an issue seen on Power systems with bnx2x which results
in the skb is NULL WARN_ON in bnx2x_free_tx_pkt firing due to the skb
pointer getting loaded in bnx2x_free_tx_pkt prior to the hw_cons
load in bnx2x_tx_int. Adding a read memory barrier resolves the issue.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is likely that 'my3216_poll()' should be 'my3126_poll()'. (1 and 2
switched in 3126.
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

allocate_flower_entry does not check for allocation success, but tries
to deref the result. I only moved the spin_lock under null check, because
 the caller is checking allocation's status at line 652.
Signed-off-by: NNavid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All constant in 'enum HCLGE_MBX_OPCODE' start with HCLGE, except
'HLCGE_MBX_PUSH_VLAN_INFO' (C and L switched)

s/HLC/HCL/
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes a copy&paste error in the original patch. Setting the wrong
register resulted in massive packet loss on some systems.

Fixes: a2928d28 ("r8169: use paged versions of phylib MDIO access functions")
Tested-by: NThomas Voegtle <tv@lio96.de>
Signed-off-by: NThomas Voegtle <tv@lio96.de>
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This object stores the flow block callbacks that are attached to this
block. Update flow_block_cb_lookup() to take this new object.

This patch restores the block sharing feature.

Fixes: da3eeb90 ("net: flow_offload: add list handling functions")
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename this type definition and adapt users.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No need to annotate the netns on the flow block callback object,
flow_block_cb_is_busy() already checks for used blocks.

Fixes: d63db30c ("net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()")
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of error, the function of_get_mac_address() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().

Fixes: d51b6ce4 ("net: ethernet: add ag71xx driver")
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: NOleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to return error code -ENOMEM from the dmam_alloc_coherent() error
handling case instead of 0, as done elsewhere in this function.

Fixes: d51b6ce4 ("net: ethernet: add ag71xx driver")
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: NOleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unlike legacy chips, 57500 chips don't need additional VNIC resources
for aRFS/ntuple.  Fix the code accordingly so that we don't reserve
and allocate additional VNICs on 57500 chips.  Without this patch,
the driver is failing to initialize when it tries to allocate extra
VNICs.

Fixes: ac33906c ("bnxt_en: Add support for aRFS on 57500 chips.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Variables allocated by kvzalloc should not be freed by kfree.
Because they may be allocated by vmalloc.
So we replace kfree with kvfree here.
Signed-off-by: NChuhong Yuan <hslester96@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Variable allocated by kvmalloc should not be freed by kfree.
Because it may be allocated by vmalloc.
So replace kfree with kvfree here.

Fixes: 9b1f2982 ("net/mlx5: Add support for FW fatal reporter dump")
Signed-off-by: NChuhong Yuan <hslester96@gmail.com>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>