BCM2708: Add core Device Tree support

raspberrypi inclusion
category: feature
bugzilla: 50432

--------------------------------

Add the bare minimum needed to boot BCM2708 from a Device Tree.
Signed-off-by: NNoralf Tronnes <notro@tronnes.org>

BCM2708: DT: change 'axi' nodename to 'soc'

Change DT node named 'axi' to 'soc' so it matches ARCH_BCM2835.
The VC4 bootloader fills in certain properties in the 'axi' subtree,
but since this is part of an upstreaming effort, the name is changed.

Signed-off-by: Noralf Tronnes notro@tronnes.org

BCM2708_DT: Correct length of the peripheral space

Use dts-dirs feature for overlays.

The kernel makefiles have a dts-dirs target that is for vendor subdirectories.

Using this fixes the install_dtbs target, which previously did not install the overlays.

BCM270X_DT: configure I2S DMA channels
Signed-off-by: NMatthias Reichl <hias@horus.com>

BCM270X_DT: switch to bcm2835-i2s

I2S soundcard drivers with proper devicetree support (i.e. not linking
to the cpu_dai/platform via name but to cpu/platform via of_node)
will work out of the box without any modifications.

When the kernel is compiled without devicetree support the platform
code will instantiate the bcm2708-i2s driver and I2S soundcard drivers
will link to it via name, as before.
Signed-off-by: NMatthias Reichl <hias@horus.com>

SDIO-overlay: add poll_once-boolean parameter

Add paramter to toggle sdio-device-polling
done every second or once at boot-time.
Signed-off-by: NPatrick Boettcher <patrick.boettcher@posteo.de>

BCM270X_DT: Make mmc overlay compatible with current firmware

The original DT overlay logic followed a merge-then-patch procedure,
i.e. parameters are applied to the loaded overlay before the overlay
is merged into the base DTB. This sequence has been changed to
patch-then-merge, in order to support parameterised node names, and
to protect against bad overlays. As a result, overrides (parameters)
must only target labels in the overlay, but the overlay can obviously target nodes in the base DTB.

mmc-overlay.dts (that switches back to the original mmc sdcard
driver) is the only overlay violating that rule, and this patch
fixes it.

bcm270x_dt: Use the sdhost MMC controller by default

The "mmc" overlay reverts to using the other controller.

squash: Add cprman to dt

BCM270X_DT: Use clk_core for I2C interfaces

BCM270X_DT: Use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi

The mainline Device Tree files are quite close to downstream now.
Let's use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi as base files
for our dts files.

Mainline dts files are based on these files:

          bcm2835-rpi.dtsi
  bcm2835.dtsi    bcm2836.dtsi
          bcm283x.dtsi

Current downstream are based on these:

  bcm2708.dtsi    bcm2709.dtsi    bcm2710.dtsi
             bcm2708_common.dtsi

This patch introduces this dependency:

  bcm2708.dtsi    bcm2709.dtsi
          bcm2708-rpi.dtsi
          bcm270x.dtsi
  bcm2835.dtsi    bcm2836.dtsi
          bcm283x.dtsi

And:
          bcm2710.dtsi
          bcm2708-rpi.dtsi
          bcm270x.dtsi
          bcm283x.dtsi

bcm270x.dtsi contains the downstream bcm283x.dtsi diff.
bcm2708-rpi.dtsi is the downstream version of bcm2835-rpi.dtsi.

Other changes:
- The led node has moved from /soc/leds to /leds. This is not a problem
  since the label is used to reference it.
- The clk_osc reg property changes from 6 to 3.
- The gpu nodes has their interrupt property set in the base file.
- the clocks label does not point to the /clocks node anymore, but
  points to the cprman node. This is not a problem since the overlays
  that use the clock node refer to it directly: target-path = "/clocks";
- some nodes now have 2 labels since mainline and downstream differs in
  this respect: cprman/clocks, spi0/spi, gpu/vc4.
- some nodes doesn't have an explicit status = "okay" since they're not
  disabled in the base file: watchdog and random.
- gpiomem doesn't need an explicit status = "okay".
- bcm2708-rpi-cm.dts got the hpd-gpios property from bcm2708_common.dtsi,
  it's now set directly in that file.
- bcm2709-rpi-2-b.dts has the timer node moved from /soc/timer to /timer.
- Removed clock-frequency property on the bcm{2709,2710}.dtsi timer nodes.
Signed-off-by: NNoralf Trønnes <noralf@tronnes.org>

BCM270X_DT: Use raspberrypi-power to turn on USB power

Use the raspberrypi-power driver to turn on USB power.
Signed-off-by: NNoralf Trønnes <noralf@tronnes.org>

BCM270X_DT: Add a .dtbo target, use for overlays

Change the filenames and extensions to keep the pre-DDT style of
overlay (<name>-overlay.dtb) distinct from new ones that use a
different style of local fixups (<name>.dtbo), and to match other
platforms.

The RPi firmware uses the DDTK trailer atom to choose which type of
overlay to use for each kernel.
Signed-off-by: NPhil Elwell <phil@raspberrypi.org>

BCM270X_DT: Don't generate "linux,phandle" props

The EPAPR standard says to use "phandle" properties to store phandles,
rather than the deprecated "linux,phandle" version. By default, dtc
generates both, but adding "-H epapr" causes it to only generate
"phandle"s, saving some space and clutter.
Signed-off-by: NPhil Elwell <phil@raspberrypi.org>

BCM270X_DT: Add overlay for enc28j60 on SPI2

Works on SPI2 for compute module

BCM270X_DT: Add midi-uart0 overlay

MIDI requires 31.25kbaud, a baudrate unsupported by Linux. The
midi-uart0 overlay configures uart0 (ttyAMA0) to use a fake clock
so that requesting 38.4kbaud actually gets 31.25kbaud.
Signed-off-by: NPhil Elwell <phil@raspberrypi.org>

BCM270X_DT: Add i2c-sensor overlay

The i2c-sensor overlay is a container for various pressure and
temperature sensors, currently bmp085 and bmp280. The standalone
bmp085_i2c-sensor overlay is now deprecated.
Signed-off-by: NPhil Elwell <phil@raspberrypi.org>

BCM270X_DT: overlays/*-overlay.dtb -> overlays/*.dtbo (#1752)

We now create overlays as .dtbo files.

build: support for .dtbo files for dtb overlays

Kernel 4.4.6+ on RaspberryPi support .dtbo files for overlays, instead of .dtb.
Patch the kernel, which has faulty rules to generate .dtbo the way yocto does
Signed-off-by: NHerve Jourdain <herve.jourdain@neuf.fr>
Signed-off-by: NKhem Raj <raj.khem@gmail.com>

BCM270X: Drop position requirement for CMA in VC4 overlay.

No longer necessary since 2aefcd576195a739a7a256099571c9c4a401005f,
and will probably let peeople that want to choose a larger CMA
allocation (particularly on pi0/1).
Signed-off-by: NEric Anholt <eric@anholt.net>

BCM270X_DT: RPi Device Tree tidy

Use the upstream sdhost node, add thermal-zones, and factor out some
common elements.
Signed-off-by: NPhil Elwell <phil@raspberrypi.org>

kbuild: Silence unhelpful DTC warnings
Signed-off-by: NPhil Elwell <phil@raspberrypi.org>

BCM270X_DT: DT build rules no longer arch-specific
Signed-off-by: NPhil Elwell <phil@raspberrypi.org>
Signed-off-by: NFang Yafen <yafen@iscas.ac.cn>
Signed-off-by: NZheng Zengkai <zhengzengkai@huawei.com>

.gitignore

@@ -18,6 +18,7 @@
 *.c.[012]*.*
 *.dt.yaml
 *.dtb
+*.dtbo
 *.dtb.S
 *.dwo
 *.elf

arch/arm/boot/dts/Makefile

 # SPDX-License-Identifier: GPL-2.0
+
+dtb-$(CONFIG_ARCH_BCM2835) += \
+	bcm2708-rpi-b.dtb \
+	bcm2708-rpi-b-rev1.dtb \
+	bcm2708-rpi-b-plus.dtb \
+	bcm2708-rpi-cm.dtb \
+	bcm2708-rpi-zero.dtb \
+	bcm2708-rpi-zero-w.dtb \
+	bcm2709-rpi-2-b.dtb \
+	bcm2710-rpi-2-b.dtb \
+	bcm2710-rpi-3-b.dtb \
+	bcm2711-rpi-4-b.dtb \
+	bcm2710-rpi-3-b-plus.dtb \
+	bcm2710-rpi-cm3.dtb \
+	bcm2711-rpi-cm4.dtb
+
 dtb-$(CONFIG_ARCH_ALPINE) += \
 	alpine-db.dtb
 dtb-$(CONFIG_MACH_ARTPEC6) += \
@@ -92,7 +108,6 @@ dtb-$(CONFIG_ARCH_BCM2835) += \
 	bcm2837-rpi-3-b.dtb \
 	bcm2837-rpi-3-b-plus.dtb \
 	bcm2837-rpi-cm3-io3.dtb \
-	bcm2711-rpi-4-b.dtb \
 	bcm2835-rpi-zero.dtb \
 	bcm2835-rpi-zero-w.dtb
 dtb-$(CONFIG_ARCH_BCM_5301X) += \
@@ -1408,3 +1423,13 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
 	aspeed-bmc-opp-zaius.dtb \
 	aspeed-bmc-portwell-neptune.dtb \
 	aspeed-bmc-quanta-q71l.dtb
+
+targets += dtbs dtbs_install
+targets += $(dtb-y)
+
+subdir-y	:= overlays
+
+# Enable fixups to support overlays on BCM2835 platforms
+ifeq ($(CONFIG_ARCH_BCM2835),y)
+	DTC_FLAGS ?= -@
+endif

arch/arm/boot/dts/bcm2708-rpi-b-plus.dts

+/dts-v1/;
+
+#include "bcm2708.dtsi"
+#include "bcm2708-rpi.dtsi"
+#include "bcm283x-rpi-smsc9514.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
+#include "bcm283x-rpi-i2c0mux_0_28.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-b-plus", "brcm,bcm2835";
+	model = "Raspberry Pi Model B+";
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins = <40 45>;
+		brcm,function = <4>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+&i2c0if {
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 47 0>;
+	};
+
+	pwr_led: pwr {
+		label = "led1";
+		linux,default-trigger = "input";
+		gpios = <&gpio 35 0>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		pwr_led_gpio = <&pwr_led>,"gpios:4";
+		pwr_led_activelow = <&pwr_led>,"gpios:8";
+		pwr_led_trigger = <&pwr_led>,"linux,default-trigger";
+	};
+};

arch/arm/boot/dts/bcm2708-rpi-b-rev1.dts

+/dts-v1/;
+
+#include "bcm2708.dtsi"
+#include "bcm2708-rpi.dtsi"
+#include "bcm283x-rpi-smsc9512.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-b", "brcm,bcm2835";
+	model = "Raspberry Pi Model B";
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <28 29 30 31>;
+		brcm,function = <6>; /* alt2 */
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins = <40 45>;
+		brcm,function = <4>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+/delete-node/ &i2c0mux;
+
+i2c0: &i2c0if {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	clock-frequency = <100000>;
+};
+
+i2c_csi_dsi: &i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+/ {
+	aliases {
+		i2c0 = &i2c0;
+	};
+
+	__overrides__ {
+		i2c0 = <&i2c0>, "status";
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 16 1>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+	};
+};

arch/arm/boot/dts/bcm2708-rpi-b.dts

+/dts-v1/;
+
+#include "bcm2708.dtsi"
+#include "bcm2708-rpi.dtsi"
+#include "bcm283x-rpi-smsc9512.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
+#include "bcm283x-rpi-i2c0mux_0_28.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-b", "brcm,bcm2835";
+	model = "Raspberry Pi Model B";
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <28 29 30 31>;
+		brcm,function = <6>; /* alt2 */
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins = <40 45>;
+		brcm,function = <4>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+&i2c0if {
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 16 1>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+	};
+};

arch/arm/boot/dts/bcm2708-rpi-bt.dtsi

+// SPDX-License-Identifier: GPL-2.0
+
+&uart0 {
+	bt: bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <3000000>;
+		shutdown-gpios = <&gpio 45 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+	};
+};
+
+&uart1 {
+	minibt: bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <460800>;
+		shutdown-gpios = <&gpio 45 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+	};
+};
+
+/ {
+	__overrides__ {
+		krnbt = <&bt>,"status";
+		krnbt_baudrate = <&bt>,"max-speed:0";
+	};
+};

arch/arm/boot/dts/bcm2708-rpi-cm.dts

+/dts-v1/;
+
+#include "bcm2708-rpi-cm.dtsi"
+#include "bcm283x-rpi-csi0-2lane.dtsi"
+#include "bcm283x-rpi-csi1-4lane.dtsi"
+#include "bcm283x-rpi-i2c0mux_0_28.dtsi"
+
+/ {
+	compatible = "raspberrypi,compute-module", "brcm,bcm2835";
+	model = "Raspberry Pi Compute Module";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins;
+		brcm,function;
+	};
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+&i2c0if {
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
+};

arch/arm/boot/dts/bcm2708-rpi-cm.dtsi

+#include "bcm2708.dtsi"
+#include "bcm2708-rpi.dtsi"
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 47 0>;
+	};
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+	};
+};

arch/arm/boot/dts/bcm2708-rpi-zero-w.dts

+/dts-v1/;
+
+#include "bcm2708.dtsi"
+#include "bcm2708-rpi.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
+#include "bcm283x-rpi-i2c0mux_0_28.dtsi"
+#include "bcm2708-rpi-bt.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-zero-w", "brcm,bcm2835";
+	model = "Raspberry Pi Zero W";
+
+	chosen {
+		bootargs = "coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 snd_bcm2835.enable_headphones=1";
+	};
+
+	aliases {
+		serial0 = &uart1;
+		serial1 = &uart0;
+		mmc1 = &mmcnr;
+	};
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	sdio_pins: sdio_pins {
+		brcm,pins = <34 35 36 37 38 39>;
+		brcm,function = <7>; /* ALT3 = SD1 */
+		brcm,pull = <0 2 2 2 2 2>;
+	};
+
+	bt_pins: bt_pins {
+		brcm,pins = <43>;
+		brcm,function = <4>; /* alt0:GPCLK2 */
+		brcm,pull = <0>; /* none */
+	};
+
+	uart0_pins: uart0_pins {
+		brcm,pins = <30 31 32 33>;
+		brcm,function = <7>; /* alt3=UART0 */
+		brcm,pull = <2 0 0 2>; /* up none none up */
+	};
+
+	uart1_pins: uart1_pins {
+		brcm,pins;
+		brcm,function;
+		brcm,pull;
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins = <>;
+		brcm,function = <>;
+	};
+};
+
+&mmcnr {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdio_pins>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins &bt_pins>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+&i2c0if {
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "actpwr";
+		gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+	};
+};

arch/arm/boot/dts/bcm2708-rpi-zero.dts

+/dts-v1/;
+
+#include "bcm2708.dtsi"
+#include "bcm2708-rpi.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
+#include "bcm283x-rpi-i2c0mux_0_28.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-zero", "brcm,bcm2835";
+	model = "Raspberry Pi Zero";
+
+	chosen {
+		bootargs = "coherent_pool=1M snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 snd_bcm2835.enable_headphones=1";
+	};
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins = <>;
+		brcm,function = <>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+&i2c0if {
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "actpwr";
+		gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+	};
+};

arch/arm/boot/dts/bcm2708-rpi.dtsi

+/* Downstream modifications common to bcm2835, bcm2836, bcm2837 */
+
+#include "bcm2835-rpi.dtsi"
+#include "bcm270x-rpi.dtsi"
+
+/ {
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0>;
+	};
+
+	aliases {
+		i2c2 = &i2c2;
+	};
+
+	__overrides__ {
+		i2c2_iknowwhatimdoing = <&i2c2>,"status";
+		i2c2_baudrate = <&i2c2>,"clock-frequency:0";
+		sd_poll_once = <&sdhost>,"non-removable?";
+	};
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	status = "okay";
+};
+
+&hdmi {
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "disabled";
+};
+
+&i2c2 {
+	status = "disabled";
+};

arch/arm/boot/dts/bcm2708.dtsi

+#include "bcm2835.dtsi"
+#include "bcm270x.dtsi"
+
+/ {
+	__overrides__ {
+		arm_freq;
+	};
+};
+
+&vc4 {
+	status = "disabled";
+};

arch/arm/boot/dts/bcm2709-rpi-2-b.dts

+/dts-v1/;
+
+#include "bcm2709.dtsi"
+#include "bcm2709-rpi.dtsi"
+#include "bcm283x-rpi-smsc9514.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
+#include "bcm283x-rpi-i2c0mux_0_28.dtsi"
+
+/ {
+	compatible = "raspberrypi,2-model-b", "brcm,bcm2836";
+	model = "Raspberry Pi 2 Model B";
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins = <40 45>;
+		brcm,function = <4>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+&i2c0if {
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 47 0>;
+	};
+
+	pwr_led: pwr {
+		label = "led1";
+		linux,default-trigger = "input";
+		gpios = <&gpio 35 0>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		pwr_led_gpio = <&pwr_led>,"gpios:4";
+		pwr_led_activelow = <&pwr_led>,"gpios:8";
+		pwr_led_trigger = <&pwr_led>,"linux,default-trigger";
+	};
+};

arch/arm/boot/dts/bcm2709-rpi.dtsi

+#include "bcm2708-rpi.dtsi"
+
+&vchiq {
+	compatible = "brcm,bcm2836-vchiq", "brcm,bcm2835-vchiq";
+};

arch/arm/boot/dts/bcm2709.dtsi

+#include "bcm2836.dtsi"
+#include "bcm270x.dtsi"
+
+/ {
+	soc {
+		ranges = <0x7e000000 0x3f000000 0x01000000>,
+		         <0x40000000 0x40000000 0x00040000>;
+
+		/delete-node/ timer@7e003000;
+	};
+
+	__overrides__ {
+		arm_freq = <&v7_cpu0>, "clock-frequency:0",
+			   <&v7_cpu1>, "clock-frequency:0",
+			   <&v7_cpu2>, "clock-frequency:0",
+			   <&v7_cpu3>, "clock-frequency:0";
+	};
+};
+
+&vc4 {
+	status = "disabled";
+};

arch/arm/boot/dts/bcm270x-rpi.dtsi

+/* Downstream modifications to bcm2835-rpi.dtsi */
+
+/ {
+	aliases {
+		audio = &audio;
+		aux = &aux;
+		sound = &sound;
+		soc = &soc;
+		dma = &dma;
+		intc = &intc;
+		watchdog = &watchdog;
+		random = &random;
+		mailbox = &mailbox;
+		gpio = &gpio;
+		uart0 = &uart0;
+		uart1 = &uart1;
+		sdhost = &sdhost;
+		mmc = &mmc;
+		mmc1 = &mmc;
+		mmc0 = &sdhost;
+		i2s = &i2s;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c10 = &i2c_csi_dsi;
+		spi0 = &spi0;
+		spi1 = &spi1;
+		spi2 = &spi2;
+		usb = &usb;
+		leds = &leds;
+		fb = &fb;
+		thermal = &thermal;
+		axiperf = &axiperf;
+	};
+
+	/* Define these notional regulators for use by overlays */
+	vdd_3v3_reg: fixedregulator_3v3 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "3v3";
+	};
+
+	vdd_5v0_reg: fixedregulator_5v0 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "5v0";
+	};
+
+	leds: leds {
+		compatible = "gpio-leds";
+	};
+
+	soc {
+		gpiomem {
+			compatible = "brcm,bcm2835-gpiomem";
+			reg = <0x7e200000 0x1000>;
+		};
+
+		fb: fb {
+			compatible = "brcm,bcm2708-fb";
+			firmware = <&firmware>;
+			status = "okay";
+		};
+
+		vcsm: vcsm {
+			compatible = "raspberrypi,bcm2835-vcsm";
+			firmware = <&firmware>;
+			status = "okay";
+		};
+
+		/* External sound card */
+		sound: sound {
+			status = "disabled";
+		};
+	};
+
+	__overrides__ {
+		cache_line_size;
+
+		uart0 = <&uart0>,"status";
+		uart1 = <&uart1>,"status";
+		i2s = <&i2s>,"status";
+		spi = <&spi0>,"status";
+		i2c0 = <&i2c0if>,"status",<&i2c0mux>,"status";
+		i2c1 = <&i2c1>,"status";
+		i2c0_baudrate = <&i2c0if>,"clock-frequency:0";
+		i2c1_baudrate = <&i2c1>,"clock-frequency:0";
+
+		audio = <&audio>,"status";
+		watchdog = <&watchdog>,"status";
+		random = <&random>,"status";
+		sd_overclock = <&sdhost>,"brcm,overclock-50:0";
+		sd_force_pio = <&sdhost>,"brcm,force-pio?";
+		sd_pio_limit = <&sdhost>,"brcm,pio-limit:0";
+		sd_debug     = <&sdhost>,"brcm,debug";
+		sdio_overclock = <&mmc>,"brcm,overclock-50:0",
+				 <&mmcnr>,"brcm,overclock-50:0";
+		axiperf      = <&axiperf>,"status";
+	};
+};
+
+&uart0 {
+	skip-init;
+};
+
+&uart1 {
+	skip-init;
+};
+
+&txp {
+	status = "disabled";
+};
+
+&i2c0if {
+	status = "disabled";
+};
+
+&i2c0mux {
+	status = "disabled";
+};
+
+&i2c1 {
+	status = "disabled";
+};
+
+&clocks {
+	firmware = <&firmware>;
+};
+
+&sdhci {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_gpio48>;
+	bus-width = <4>;
+};
+
+&cpu_thermal {
+	/delete-node/ trips;
+};
+
+&vec {
+	status = "disabled";
+};
+
+&vchiq {
+	/* Onboard audio */
+	audio: bcm2835_audio {
+		compatible = "brcm,bcm2835-audio";
+		brcm,pwm-channels = <8>;
+		status = "disabled";
+	};
+};

arch/arm/boot/dts/bcm270x.dtsi

+/* Downstream bcm283x.dtsi diff */
+#include <dt-bindings/power/raspberrypi-power.h>
+
+/ {
+	chosen {
+		bootargs = "coherent_pool=1M snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 snd_bcm2835.enable_headphones=1";
+		/delete-property/ stdout-path;
+	};
+
+	soc: soc {
+
+		watchdog: watchdog@7e100000 {
+			/* Add label */
+		};
+
+		random: rng@7e104000 {
+			/* Add label */
+		};
+
+		spi0: spi@7e204000 {
+			/* Add label */
+		};
+
+#ifndef BCM2711
+		pixelvalve0: pixelvalve@7e206000 {
+			/* Add label */
+			status = "disabled";
+		};
+
+		pixelvalve1: pixelvalve@7e207000 {
+			/* Add label */
+			status = "disabled";
+		};
+#endif
+
+		/delete-node/ sdhci@7e300000;
+
+		sdhci: mmc: mmc@7e300000 {
+			compatible = "brcm,bcm2835-mmc", "brcm,bcm2835-sdhci";
+			reg = <0x7e300000 0x100>;
+			interrupts = <2 30>;
+			clocks = <&clocks BCM2835_CLOCK_EMMC>;
+			dmas = <&dma 11>;
+			dma-names = "rx-tx";
+			brcm,overclock-50 = <0>;
+			status = "disabled";
+		};
+
+		/* A clone of mmc but with non-removable set */
+		mmcnr: mmcnr@7e300000 {
+			compatible = "brcm,bcm2835-mmc", "brcm,bcm2835-sdhci";
+			reg = <0x7e300000 0x100>;
+			interrupts = <2 30>;
+			clocks = <&clocks BCM2835_CLOCK_EMMC>;
+			dmas = <&dma 11>;
+			dma-names = "rx-tx";
+			brcm,overclock-50 = <0>;
+			non-removable;
+			status = "disabled";
+		};
+
+		hvs: hvs@7e400000 {
+			/* Add label */
+			status = "disabled";
+		};
+
+		firmwarekms: firmwarekms@7e600000 {
+			compatible = "raspberrypi,rpi-firmware-kms";
+			/* SMI interrupt reg */
+			reg = <0x7e600000 0x100>;
+			interrupts = <2 16>;
+			brcm,firmware = <&firmware>;
+			status = "disabled";
+		};
+
+		smi: smi@7e600000 {
+			compatible = "brcm,bcm2835-smi";
+			reg = <0x7e600000 0x100>;
+			interrupts = <2 16>;
+			clocks = <&clocks BCM2835_CLOCK_SMI>;
+			assigned-clocks = <&clocks BCM2835_CLOCK_SMI>;
+			assigned-clock-rates = <125000000>;
+			dmas = <&dma 4>;
+			dma-names = "rx-tx";
+			status = "disabled";
+		};
+
+		csi0: csi@7e800000 {
+			compatible = "brcm,bcm2835-unicam";
+			reg = <0x7e800000 0x800>,
+			      <0x7e802000 0x4>;
+			interrupts = <2 6>;
+			clocks = <&clocks BCM2835_CLOCK_CAM0>,
+				 <&firmware_clocks 4>;
+			clock-names = "lp", "vpu";
+			power-domains = <&power RPI_POWER_DOMAIN_UNICAM0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#clock-cells = <1>;
+			status = "disabled";
+		};
+
+		csi1: csi@7e801000 {
+			compatible = "brcm,bcm2835-unicam";
+			reg = <0x7e801000 0x800>,
+			      <0x7e802004 0x4>;
+			interrupts = <2 7>;
+			clocks = <&clocks BCM2835_CLOCK_CAM1>,
+				 <&firmware_clocks 4>;
+			clock-names = "lp", "vpu";
+			power-domains = <&power RPI_POWER_DOMAIN_UNICAM1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#clock-cells = <1>;
+			status = "disabled";
+		};
+
+#ifndef BCM2711
+		pixelvalve2: pixelvalve@7e807000 {
+			/* Add label */
+			status = "disabled";
+		};
+#endif
+
+		hdmi@7e902000 { /* hdmi */
+			status = "disabled";
+		};
+
+		usb@7e980000 { /* usb */
+			compatible = "brcm,bcm2708-usb";
+			reg = <0x7e980000 0x10000>,
+			      <0x7e006000 0x1000>;
+			interrupt-names = "usb",
+					  "soft";
+			interrupts = <1 9>,
+				     <2 0>;
+		};
+
+#ifndef BCM2711
+		v3d@7ec00000 { /* vd3 */
+			compatible = "brcm,vc4-v3d";
+			power-domains = <&power RPI_POWER_DOMAIN_V3D>;
+			status = "disabled";
+		};
+#endif
+
+		axiperf: axiperf {
+			compatible = "brcm,bcm2835-axiperf";
+			reg = <0x7e009800 0x100>,
+			      <0x7ee08000 0x100>;
+			firmware = <&firmware>;
+			status = "disabled";
+		};
+	};
+
+	__overrides__ {
+		cam0-pwdn-ctrl;
+		cam0-pwdn;
+		cam0-led-ctrl;
+		cam0-led;
+	};
+};
+
+&gpio {
+	interrupts = <2 17>, <2 18>;
+
+	dpi_18bit_gpio0: dpi_18bit_gpio0 {
+		brcm,pins = <0 1 2 3 4 5 6 7 8 9 10 11
+			     12 13 14 15 16 17 18 19
+			     20 21>;
+		brcm,function = <BCM2835_FSEL_ALT2>;
+	};
+};
+
+&uart0 {
+	/* Enable CTS bug workaround */
+	cts-event-workaround;
+};
+
+&i2s {
+	#sound-dai-cells = <0>;
+	dmas = <&dma 2>, <&dma 3>;
+	dma-names = "tx", "rx";
+};
+
+&sdhost {
+	dmas = <&dma (13|(1<<29))>;
+	dma-names = "rx-tx";
+	bus-width = <4>;
+	brcm,overclock-50 = <0>;
+	brcm,pio-limit = <1>;
+};
+
+&spi0 {
+	dmas = <&dma 6>, <&dma 7>;
+	dma-names = "tx", "rx";
+};

arch/arm/boot/dts/bcm2710-rpi-2-b.dts

+/dts-v1/;
+
+#include "bcm2710.dtsi"
+#include "bcm2709-rpi.dtsi"
+#include "bcm283x-rpi-smsc9514.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
+#include "bcm283x-rpi-i2c0mux_0_28.dtsi"
+
+/ {
+	compatible = "raspberrypi,2-model-b-rev2", "brcm,bcm2837";
+	model = "Raspberry Pi 2 Model B rev 1.2";
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins = <40 45>;
+		brcm,function = <4>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+&i2c0if {
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 47 0>;
+	};
+
+	pwr_led: pwr {
+		label = "led1";
+		linux,default-trigger = "input";
+		gpios = <&gpio 35 0>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		pwr_led_gpio = <&pwr_led>,"gpios:4";
+		pwr_led_activelow = <&pwr_led>,"gpios:8";
+		pwr_led_trigger = <&pwr_led>,"linux,default-trigger";
+	};
+};

arch/arm/boot/dts/bcm2710-rpi-3-b-plus.dts

+/dts-v1/;
+
+#include "bcm2710.dtsi"
+#include "bcm2709-rpi.dtsi"
+#include "bcm283x-rpi-lan7515.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
+#include "bcm283x-rpi-i2c0mux_0_44.dtsi"
+#include "bcm271x-rpi-bt.dtsi"
+
+/ {
+	compatible = "raspberrypi,3-model-b-plus", "brcm,bcm2837";
+	model = "Raspberry Pi 3 Model B+";
+
+	chosen {
+		bootargs = "coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 snd_bcm2835.enable_headphones=1";
+	};
+
+	aliases {
+		serial0 = &uart1;
+		serial1 = &uart0;
+		mmc1 = &mmcnr;
+	};
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	sdio_pins: sdio_pins {
+		brcm,pins =     <34 35 36 37 38 39>;
+		brcm,function = <7>; // alt3 = SD1
+		brcm,pull =     <0 2 2 2 2 2>;
+	};
+
+	bt_pins: bt_pins {
+		brcm,pins = <43>;
+		brcm,function = <4>; /* alt0:GPCLK2 */
+		brcm,pull = <0>;
+	};
+
+	uart0_pins: uart0_pins {
+		brcm,pins = <32 33>;
+		brcm,function = <7>; /* alt3=UART0 */
+		brcm,pull = <0 2>;
+	};
+
+	uart1_pins: uart1_pins {
+		brcm,pins;
+		brcm,function;
+		brcm,pull;
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins = <40 41>;
+		brcm,function = <4>;
+	};
+};
+
+&mmcnr {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdio_pins>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&firmware {
+	expgpio: expgpio {
+		compatible = "raspberrypi,firmware-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		status = "okay";
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins &bt_pins>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "okay";
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+&i2c0if {
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 29 0>;
+	};
+
+	pwr_led: pwr {
+		label = "led1";
+		linux,default-trigger = "default-on";
+		gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+&eth_phy {
+	microchip,eee-enabled;
+	microchip,tx-lpi-timer = <600>; /* non-aggressive*/
+	microchip,downshift-after = <2>;
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		pwr_led_gpio = <&pwr_led>,"gpios:4";
+		pwr_led_activelow = <&pwr_led>,"gpios:8";
+		pwr_led_trigger = <&pwr_led>,"linux,default-trigger";
+
+		eee = <&eth_phy>,"microchip,eee-enabled?";
+		tx_lpi_timer = <&eth_phy>,"microchip,tx-lpi-timer:0";
+		eth_led0 = <&eth_phy>,"microchip,led-modes:0";
+		eth_led1 = <&eth_phy>,"microchip,led-modes:4";
+		eth_downshift_after = <&eth_phy>,"microchip,downshift-after:0";
+		eth_max_speed = <&eth_phy>,"max-speed:0";
+	};
+};

arch/arm/boot/dts/bcm2710-rpi-3-b.dts

+/dts-v1/;
+
+#include "bcm2710.dtsi"
+#include "bcm2709-rpi.dtsi"
+#include "bcm283x-rpi-smsc9514.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
+#include "bcm283x-rpi-i2c0mux_0_44.dtsi"
+#include "bcm271x-rpi-bt.dtsi"
+
+/ {
+	compatible = "raspberrypi,3-model-b", "brcm,bcm2837";
+	model = "Raspberry Pi 3 Model B";
+
+	chosen {
+		bootargs = "coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 snd_bcm2835.enable_headphones=1";
+	};
+
+	aliases {
+		serial0 = &uart1;
+		serial1 = &uart0;
+		mmc1 = &mmcnr;
+	};
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	sdio_pins: sdio_pins {
+		brcm,pins =     <34 35 36 37 38 39>;
+		brcm,function = <7>; // alt3 = SD1
+		brcm,pull =     <0 2 2 2 2 2>;
+	};
+
+	bt_pins: bt_pins {
+		brcm,pins = <43>;
+		brcm,function = <4>; /* alt0:GPCLK2 */
+		brcm,pull = <0>;
+	};
+
+	uart0_pins: uart0_pins {
+		brcm,pins = <32 33>;
+		brcm,function = <7>; /* alt3=UART0 */
+		brcm,pull = <0 2>;
+	};
+
+	uart1_pins: uart1_pins {
+		brcm,pins;
+		brcm,function;
+		brcm,pull;
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins = <40 41>;
+		brcm,function = <4>;
+	};
+};
+
+&mmcnr {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdio_pins>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&soc {
+	virtgpio: virtgpio {
+		compatible = "brcm,bcm2835-virtgpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		firmware = <&firmware>;
+		status = "okay";
+	};
+
+};
+
+&firmware {
+	expgpio: expgpio {
+		compatible = "raspberrypi,firmware-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		status = "okay";
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins &bt_pins>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "okay";
+};
+
+&bt {
+	max-speed = <921600>;
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+&i2c0if {
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&virtgpio 0 0>;
+	};
+
+	pwr_led: pwr {
+		label = "led1";
+		linux,default-trigger = "input";
+		gpios = <&expgpio 7 0>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&expgpio 4 GPIO_ACTIVE_LOW>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		pwr_led_gpio = <&pwr_led>,"gpios:4";
+		pwr_led_activelow = <&pwr_led>,"gpios:8";
+		pwr_led_trigger = <&pwr_led>,"linux,default-trigger";
+	};
+};

arch/arm/boot/dts/bcm2710-rpi-cm3.dts

+/dts-v1/;
+
+#include "bcm2710.dtsi"
+#include "bcm2709-rpi.dtsi"
+#include "bcm283x-rpi-csi0-2lane.dtsi"
+#include "bcm283x-rpi-csi1-4lane.dtsi"
+#include "bcm283x-rpi-i2c0mux_0_28.dtsi"
+/ {
+	compatible = "raspberrypi,3-compute-module", "brcm,bcm2837";
+	model = "Raspberry Pi Compute Module 3";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <1>; /* output */
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <4>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <4>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <4>; /* alt0 */
+	};
+
+	audio_pins: audio_pins {
+		brcm,pins;
+		brcm,function;
+	};
+};
+
+&soc {
+	virtgpio: virtgpio {
+		compatible = "brcm,bcm2835-virtgpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		firmware = <&firmware>;
+		status = "okay";
+	};
+
+};
+
+&firmware {
+	expgpio: expgpio {
+		compatible = "raspberrypi,firmware-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		status = "okay";
+	};
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+&i2c0if {
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&virtgpio 0 0>;
+	};
+};
+
+&hdmi {
+	hpd-gpios = <&expgpio 0 GPIO_ACTIVE_LOW>;
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+	};
+};

arch/arm/boot/dts/bcm2710.dtsi

+#include "bcm2837.dtsi"
+#include "bcm270x.dtsi"
+
+/ {
+	compatible = "brcm,bcm2837", "brcm,bcm2836";
+
+	arm-pmu {
+#ifdef RPI364
+		compatible = "arm,armv8-pmuv3", "arm,cortex-a7-pmu";
+#else
+		compatible = "arm,cortex-a7-pmu";
+#endif
+	};
+
+	soc {
+		/delete-node/ timer@7e003000;
+	};
+
+	__overrides__ {
+		arm_freq = <&cpu0>, "clock-frequency:0",
+		       <&cpu1>, "clock-frequency:0",
+		       <&cpu2>, "clock-frequency:0",
+		       <&cpu3>, "clock-frequency:0";
+	};
+};
+
+&vc4 {
+	status = "disabled";
+};

arch/arm/boot/dts/bcm2711-rpi-4-b.dts

@@ -2,7 +2,6 @@
 /dts-v1/;
 #include "bcm2711.dtsi"
 #include "bcm2835-rpi.dtsi"
-#include "bcm283x-rpi-usb-peripheral.dtsi"
 
 #include <dt-bindings/reset/raspberrypi,firmware-reset.h>
 
@@ -95,7 +94,7 @@
 				  "VDD_SD_IO_SEL",
 				  "CAM_GPIO",
 				  "SD_PWR_ON",
-				  "";
+				  "SD_OC_N";
 		status = "okay";
 	};
 
@@ -301,3 +300,306 @@
 &vec {
 	status = "disabled";
 };
+
+// =============================================
+// Downstream rpi- changes
+
+#define BCM2711
+
+#include "bcm270x.dtsi"
+#include "bcm271x-rpi-bt.dtsi"
+
+/ {
+	soc {
+		/delete-node/ pixelvalve@7e807000;
+		/delete-node/ hdmi@7e902000;
+	};
+};
+
+#include "bcm2711-rpi.dtsi"
+#include "bcm283x-rpi-csi1-2lane.dtsi"
+#include "bcm283x-rpi-i2c0mux_0_44.dtsi"
+
+/ {
+	chosen {
+		bootargs = "coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 snd_bcm2835.enable_headphones=1";
+	};
+
+	aliases {
+		serial0 = &uart1;
+		serial1 = &uart0;
+		mmc0 = &emmc2;
+		mmc1 = &mmcnr;
+		mmc2 = &sdhost;
+		/delete-property/ i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		i2c5 = &i2c5;
+		i2c6 = &i2c6;
+		/delete-property/ intc;
+	};
+
+	/delete-node/ wifi-pwrseq;
+};
+
+&mmcnr {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdio_pins>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-0 = <&uart0_pins &bt_pins>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-0 = <&uart1_pins>;
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <BCM2835_FSEL_GPIO_OUT>;
+	};
+
+	spi3_pins: spi3_pins {
+		brcm,pins = <1 2 3>;
+		brcm,function = <BCM2835_FSEL_ALT3>;
+	};
+
+	spi3_cs_pins: spi3_cs_pins {
+		brcm,pins = <0 24>;
+		brcm,function = <BCM2835_FSEL_GPIO_OUT>;
+	};
+
+	spi4_pins: spi4_pins {
+		brcm,pins = <5 6 7>;
+		brcm,function = <BCM2835_FSEL_ALT3>;
+	};
+
+	spi4_cs_pins: spi4_cs_pins {
+		brcm,pins = <4 25>;
+		brcm,function = <BCM2835_FSEL_GPIO_OUT>;
+	};
+
+	spi5_pins: spi5_pins {
+		brcm,pins = <13 14 15>;
+		brcm,function = <BCM2835_FSEL_ALT3>;
+	};
+
+	spi5_cs_pins: spi5_cs_pins {
+		brcm,pins = <12 26>;
+		brcm,function = <BCM2835_FSEL_GPIO_OUT>;
+	};
+
+	spi6_pins: spi6_pins {
+		brcm,pins = <19 20 21>;
+		brcm,function = <BCM2835_FSEL_ALT3>;
+	};
+
+	spi6_cs_pins: spi6_cs_pins {
+		brcm,pins = <18 27>;
+		brcm,function = <BCM2835_FSEL_GPIO_OUT>;
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+		brcm,pull = <BCM2835_PUD_UP>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+		brcm,pull = <BCM2835_PUD_UP>;
+	};
+
+	i2c3_pins: i2c3 {
+		brcm,pins = <4 5>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+		brcm,pull = <BCM2835_PUD_UP>;
+	};
+
+	i2c4_pins: i2c4 {
+		brcm,pins = <8 9>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+		brcm,pull = <BCM2835_PUD_UP>;
+	};
+
+	i2c5_pins: i2c5 {
+		brcm,pins = <12 13>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+		brcm,pull = <BCM2835_PUD_UP>;
+	};
+
+	i2c6_pins: i2c6 {
+		brcm,pins = <22 23>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+		brcm,pull = <BCM2835_PUD_UP>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+	};
+
+	sdio_pins: sdio_pins {
+		brcm,pins =     <34 35 36 37 38 39>;
+		brcm,function = <BCM2835_FSEL_ALT3>; // alt3 = SD1
+		brcm,pull =     <0 2 2 2 2 2>;
+	};
+
+	bt_pins: bt_pins {
+		brcm,pins = "-"; // non-empty to keep btuart happy, //4 = 0
+				 // to fool pinctrl
+		brcm,function = <0>;
+		brcm,pull = <2>;
+	};
+
+	uart0_pins: uart0_pins {
+		brcm,pins = <32 33>;
+		brcm,function = <BCM2835_FSEL_ALT3>;
+		brcm,pull = <0 2>;
+	};
+
+	uart1_pins: uart1_pins {
+		brcm,pins;
+		brcm,function;
+		brcm,pull;
+	};
+
+	uart2_pins: uart2_pins {
+		brcm,pins = <0 1>;
+		brcm,function = <BCM2835_FSEL_ALT4>;
+		brcm,pull = <0 2>;
+	};
+
+	uart3_pins: uart3_pins {
+		brcm,pins = <4 5>;
+		brcm,function = <BCM2835_FSEL_ALT4>;
+		brcm,pull = <0 2>;
+	};
+
+	uart4_pins: uart4_pins {
+		brcm,pins = <8 9>;
+		brcm,function = <BCM2835_FSEL_ALT4>;
+		brcm,pull = <0 2>;
+	};
+
+	uart5_pins: uart5_pins {
+		brcm,pins = <12 13>;
+		brcm,function = <BCM2835_FSEL_ALT4>;
+		brcm,pull = <0 2>;
+	};
+};
+
+&i2c0if {
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+/ {
+	__overrides__ {
+		/delete-property/ i2c2_baudrate;
+		/delete-property/ i2c2_iknowwhatimdoing;
+	};
+};
+
+// =============================================
+// Board specific stuff here
+
+&sdhost {
+	status = "disabled";
+};
+
+&phy1 {
+	led-modes = <0x00 0x08>; /* link/activity link */
+};
+
+&gpio {
+	audio_pins: audio_pins {
+		brcm,pins = <40 41>;
+		brcm,function = <4>;
+	};
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
+	};
+
+	pwr_led: pwr {
+		label = "led1";
+		linux,default-trigger = "default-on";
+		gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&pwm1 {
+	status = "disabled";
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		pwr_led_gpio = <&pwr_led>,"gpios:4";
+		pwr_led_activelow = <&pwr_led>,"gpios:8";
+		pwr_led_trigger = <&pwr_led>,"linux,default-trigger";
+
+		eth_led0 = <&phy1>,"led-modes:0";
+		eth_led1 = <&phy1>,"led-modes:4";
+
+		sd_poll_once = <&emmc2>, "non-removable?";
+		spi_dma4 = <&spi0>, "dmas:0=", <&dma40>,
+			   <&spi0>, "dmas:8=", <&dma40>;
+	};
+};

arch/arm/boot/dts/bcm2711-rpi-cm4.dts

+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2711.dtsi"
+#include "bcm2835-rpi.dtsi"
+
+/ {
+	compatible = "raspberrypi,4-compute-module", "brcm,bcm2711";
+	model = "Raspberry Pi Compute Module 4";
+
+	chosen {
+		/* 8250 auxiliary UART instead of pl011 */
+		stdout-path = "serial1:115200n8";
+	};
+
+	/* Will be filled by the bootloader */
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0 0>;
+	};
+
+	aliases {
+		emmc2bus = &emmc2bus;
+		ethernet0 = &genet;
+		pcie0 = &pcie0;
+	};
+
+	leds {
+		act {
+			gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
+		};
+
+		pwr {
+			label = "PWR";
+			gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
+			linux,default-trigger = "default-on";
+		};
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
+	};
+
+	sd_io_1v8_reg: sd_io_1v8_reg {
+		compatible = "regulator-gpio";
+		regulator-name = "vdd-sd-io";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-settling-time-us = <5000>;
+		gpios = <&expgpio 4 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0x1
+			  3300000 0x0>;
+		status = "okay";
+	};
+
+	sd_vcc_reg: sd_vcc_reg {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-sd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&expgpio 6 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&ddc0 {
+	status = "okay";
+};
+
+&ddc1 {
+	status = "okay";
+};
+
+&firmware {
+	expgpio: gpio {
+		compatible = "raspberrypi,firmware-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "BT_ON",
+				  "WL_ON",
+				  "PWR_LED_OFF",
+				  "ANT1",
+				  "VDD_SD_IO_SEL",
+				  "CAM_GPIO",
+				  "SD_PWR_ON",
+				  "ANT2";
+		status = "okay";
+
+		ant1: ant1 {
+			gpio-hog;
+			gpios = <3 GPIO_ACTIVE_HIGH>;
+			output-high;
+		};
+
+		ant2: ant2 {
+			gpio-hog;
+			gpios = <7 GPIO_ACTIVE_HIGH>;
+			output-low;
+		};
+	};
+};
+
+&gpio {
+	/*
+	 * Parts taken from rpi_SCH_4b_4p0_reduced.pdf and
+	 * the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD1",
+			  "RXD1",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "RGMII_MDIO",
+			  "RGMIO_MDC",
+			  /* Used by BT module */
+			  "CTS0",
+			  "RTS0",
+			  "TXD0",
+			  "RXD0",
+			  /* Used by Wifi */
+			  "SD1_CLK",
+			  "SD1_CMD",
+			  "SD1_DATA0",
+			  "SD1_DATA1",
+			  "SD1_DATA2",
+			  "SD1_DATA3",
+			  /* Shared with SPI flash */
+			  "PWM0_MISO",
+			  "PWM1_MOSI",
+			  "STATUS_LED_G_CLK",
+			  "SPIFLASH_CE_N",
+			  "SDA0",
+			  "SCL0",
+			  "RGMII_RXCLK",
+			  "RGMII_RXCTL",
+			  "RGMII_RXD0",
+			  "RGMII_RXD1",
+			  "RGMII_RXD2",
+			  "RGMII_RXD3",
+			  "RGMII_TXCLK",
+			  "RGMII_TXCTL",
+			  "RGMII_TXD0",
+			  "RGMII_TXD1",
+			  "RGMII_TXD2",
+			  "RGMII_TXD3";
+};
+
+&hdmi0 {
+	clocks = <&firmware_clocks 13>, <&firmware_clocks 14>, <&dvp 0>, <&clk_27MHz>;
+	clock-names = "hdmi", "bvb", "audio", "cec";
+	status = "okay";
+};
+
+&hdmi1 {
+	clocks = <&firmware_clocks 13>, <&firmware_clocks 14>, <&dvp 1>, <&clk_27MHz>;
+	clock-names = "hdmi", "bvb", "audio", "cec";
+	status = "okay";
+};
+
+&hvs {
+	clocks = <&firmware_clocks 4>;
+};
+
+&pixelvalve0 {
+	status = "okay";
+};
+
+&pixelvalve1 {
+	status = "okay";
+};
+
+&pixelvalve2 {
+	status = "okay";
+};
+
+&pixelvalve4 {
+	status = "okay";
+};
+
+&vc4 {
+	status = "okay";
+};
+
+&vec {
+	status = "disabled";
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm1_0_gpio40 &pwm1_1_gpio41>;
+	status = "okay";
+};
+
+/* SDHCI is used to control the SDIO for wireless */
+&sdhci {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_gpio34>;
+	bus-width = <4>;
+	non-removable;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+/* EMMC2 is used to drive the EMMC card */
+&emmc2 {
+	bus-width = <8>;
+	vqmmc-supply = <&sd_io_1v8_reg>;
+	vmmc-supply = <&sd_vcc_reg>;
+	broken-cd;
+	status = "okay";
+};
+
+&genet {
+	phy-handle = <&phy1>;
+	phy-mode = "rgmii-rxid";
+	status = "okay";
+};
+
+&genet_mdio {
+	phy1: ethernet-phy@1 {
+		/* No PHY interrupt */
+		reg = <0x1>;
+	};
+};
+
+/* uart0 communicates with the BT module */
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <2000000>;
+		shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+/* uart1 is mapped to the pin header */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_gpio14>;
+	status = "okay";
+};
+
+&vchiq {
+	interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+// =============================================
+// Downstream rpi- changes
+
+#define BCM2711
+
+#include "bcm270x.dtsi"
+#include "bcm271x-rpi-bt.dtsi"
+
+/ {
+	soc {
+		/delete-node/ pixelvalve@7e807000;
+		/delete-node/ hdmi@7e902000;
+	};
+};
+
+#include "bcm2711-rpi.dtsi"
+#include "bcm283x-rpi-csi0-2lane.dtsi"
+#include "bcm283x-rpi-csi1-4lane.dtsi"
+#include "bcm283x-rpi-i2c0mux_0_44.dtsi"
+
+/ {
+	chosen {
+		bootargs = "coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 snd_bcm2835.enable_headphones=1";
+	};
+
+	aliases {
+		serial0 = &uart1;
+		serial1 = &uart0;
+		mmc0 = &emmc2;
+		mmc1 = &mmcnr;
+		mmc2 = &sdhost;
+		/delete-property/ i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		i2c5 = &i2c5;
+		i2c6 = &i2c6;
+		/delete-property/ intc;
+	};
+
+	/delete-node/ wifi-pwrseq;
+};
+
+&mmcnr {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdio_pins>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-0 = <&uart0_pins &bt_pins>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-0 = <&uart1_pins>;
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
+	cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
+
+	spidev0: spidev@0{
+		compatible = "spidev";
+		reg = <0>;	/* CE0 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+
+	spidev1: spidev@1{
+		compatible = "spidev";
+		reg = <1>;	/* CE1 */
+		#address-cells = <1>;
+		#size-cells = <0>;
+		spi-max-frequency = <125000000>;
+	};
+};
+
+&gpio {
+	spi0_pins: spi0_pins {
+		brcm,pins = <9 10 11>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+	};
+
+	spi0_cs_pins: spi0_cs_pins {
+		brcm,pins = <8 7>;
+		brcm,function = <BCM2835_FSEL_GPIO_OUT>;
+	};
+
+	spi3_pins: spi3_pins {
+		brcm,pins = <1 2 3>;
+		brcm,function = <BCM2835_FSEL_ALT3>;
+	};
+
+	spi3_cs_pins: spi3_cs_pins {
+		brcm,pins = <0 24>;
+		brcm,function = <BCM2835_FSEL_GPIO_OUT>;
+	};
+
+	spi4_pins: spi4_pins {
+		brcm,pins = <5 6 7>;
+		brcm,function = <BCM2835_FSEL_ALT3>;
+	};
+
+	spi4_cs_pins: spi4_cs_pins {
+		brcm,pins = <4 25>;
+		brcm,function = <BCM2835_FSEL_GPIO_OUT>;
+	};
+
+	spi5_pins: spi5_pins {
+		brcm,pins = <13 14 15>;
+		brcm,function = <BCM2835_FSEL_ALT3>;
+	};
+
+	spi5_cs_pins: spi5_cs_pins {
+		brcm,pins = <12 26>;
+		brcm,function = <BCM2835_FSEL_GPIO_OUT>;
+	};
+
+	spi6_pins: spi6_pins {
+		brcm,pins = <19 20 21>;
+		brcm,function = <BCM2835_FSEL_ALT3>;
+	};
+
+	spi6_cs_pins: spi6_cs_pins {
+		brcm,pins = <18 27>;
+		brcm,function = <BCM2835_FSEL_GPIO_OUT>;
+	};
+
+	i2c0_pins: i2c0 {
+		brcm,pins = <0 1>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+		brcm,pull = <BCM2835_PUD_UP>;
+	};
+
+	i2c1_pins: i2c1 {
+		brcm,pins = <2 3>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+		brcm,pull = <BCM2835_PUD_UP>;
+	};
+
+	i2c3_pins: i2c3 {
+		brcm,pins = <4 5>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+		brcm,pull = <BCM2835_PUD_UP>;
+	};
+
+	i2c4_pins: i2c4 {
+		brcm,pins = <8 9>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+		brcm,pull = <BCM2835_PUD_UP>;
+	};
+
+	i2c5_pins: i2c5 {
+		brcm,pins = <12 13>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+		brcm,pull = <BCM2835_PUD_UP>;
+	};
+
+	i2c6_pins: i2c6 {
+		brcm,pins = <22 23>;
+		brcm,function = <BCM2835_FSEL_ALT5>;
+		brcm,pull = <BCM2835_PUD_UP>;
+	};
+
+	i2s_pins: i2s {
+		brcm,pins = <18 19 20 21>;
+		brcm,function = <BCM2835_FSEL_ALT0>;
+	};
+
+	sdio_pins: sdio_pins {
+		brcm,pins =     <34 35 36 37 38 39>;
+		brcm,function = <BCM2835_FSEL_ALT3>; // alt3 = SD1
+		brcm,pull =     <0 2 2 2 2 2>;
+	};
+
+	bt_pins: bt_pins {
+		brcm,pins = "-"; // non-empty to keep btuart happy, //4 = 0
+				 // to fool pinctrl
+		brcm,function = <0>;
+		brcm,pull = <2>;
+	};
+
+	uart0_pins: uart0_pins {
+		brcm,pins = <32 33>;
+		brcm,function = <BCM2835_FSEL_ALT3>;
+		brcm,pull = <0 2>;
+	};
+
+	uart1_pins: uart1_pins {
+		brcm,pins;
+		brcm,function;
+		brcm,pull;
+	};
+
+	uart2_pins: uart2_pins {
+		brcm,pins = <0 1>;
+		brcm,function = <BCM2835_FSEL_ALT4>;
+		brcm,pull = <0 2>;
+	};
+
+	uart3_pins: uart3_pins {
+		brcm,pins = <4 5>;
+		brcm,function = <BCM2835_FSEL_ALT4>;
+		brcm,pull = <0 2>;
+	};
+
+	uart4_pins: uart4_pins {
+		brcm,pins = <8 9>;
+		brcm,function = <BCM2835_FSEL_ALT4>;
+		brcm,pull = <0 2>;
+	};
+
+	uart5_pins: uart5_pins {
+		brcm,pins = <12 13>;
+		brcm,function = <BCM2835_FSEL_ALT4>;
+		brcm,pull = <0 2>;
+	};
+};
+
+&i2c0if {
+	clock-frequency = <100000>;
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+};
+
+&i2s {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s_pins>;
+};
+
+/ {
+	__overrides__ {
+		/delete-property/ i2c2_baudrate;
+		/delete-property/ i2c2_iknowwhatimdoing;
+	};
+};
+
+// =============================================
+// Board specific stuff here
+
+&pcie0 {
+       brcm,enable-l1ss;
+};
+
+&sdhost {
+	status = "disabled";
+};
+
+&phy1 {
+	led-modes = <0x00 0x08>; /* link/activity link */
+};
+
+&gpio {
+	audio_pins: audio_pins {
+		brcm,pins = <40 41>;
+		brcm,function = <4>;
+	};
+};
+
+&leds {
+	act_led: act {
+		label = "led0";
+		linux,default-trigger = "mmc0";
+		gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
+	};
+
+	pwr_led: pwr {
+		label = "led1";
+		linux,default-trigger = "default-on";
+		gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&pwm1 {
+	status = "disabled";
+};
+
+&audio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+};
+
+/ {
+	__overrides__ {
+		act_led_gpio = <&act_led>,"gpios:4";
+		act_led_activelow = <&act_led>,"gpios:8";
+		act_led_trigger = <&act_led>,"linux,default-trigger";
+
+		pwr_led_gpio = <&pwr_led>,"gpios:4";
+		pwr_led_activelow = <&pwr_led>,"gpios:8";
+		pwr_led_trigger = <&pwr_led>,"linux,default-trigger";
+
+		eth_led0 = <&phy1>,"led-modes:0";
+		eth_led1 = <&phy1>,"led-modes:4";
+
+		ant1 =  <&ant1>,"output-high?=on",
+			<&ant1>, "output-low?=off",
+			<&ant2>, "output-high?=off",
+			<&ant2>, "output-low?=on";
+		ant2 =  <&ant1>,"output-high?=off",
+			<&ant1>, "output-low?=on",
+			<&ant2>, "output-high?=on",
+			<&ant2>, "output-low?=off";
+		noant = <&ant1>,"output-high?=off",
+			<&ant1>, "output-low?=on",
+			<&ant2>, "output-high?=off",
+			<&ant2>, "output-low?=on";
+
+		sd_poll_once = <&emmc2>, "non-removable?";
+		spi_dma4 = <&spi0>, "dmas:0=", <&dma40>,
+			   <&spi0>, "dmas:8=", <&dma40>;
+	};
+};

arch/arm/boot/dts/bcm2711-rpi.dtsi

+// SPDX-License-Identifier: GPL-2.0
+#include "bcm270x-rpi.dtsi"
+
+/ {
+	__overrides__ {
+		arm_freq;
+	};
+
+	v3dbus: v3dbus {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <2>;
+		ranges = <0x7c500000  0x0 0xfc500000  0x0 0x03300000>,
+			 <0x40000000  0x0 0xff800000  0x0 0x00800000>;
+		dma-ranges = <0x00000000  0x0 0x00000000  0x4 0x00000000>;
+
+		v3d: v3d@7ec04000 {
+			compatible = "brcm,2711-v3d";
+			reg =
+			    <0x7ec00000  0x0 0x4000>,
+			    <0x7ec04000  0x0 0x4000>;
+			reg-names = "hub", "core0";
+
+			power-domains = <&pm BCM2835_POWER_DOMAIN_GRAFX_V3D>;
+			resets = <&pm BCM2835_RESET_V3D>;
+			clocks = <&firmware_clocks 5>;
+			clocks-names = "v3d";
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+	};
+
+	scb: scb {
+	     /* Add a label */
+	};
+};
+
+&cma {
+	/* Limit cma to the lower 768MB to allow room for HIGHMEM on 32-bit */
+	alloc-ranges = <0x0 0x00000000 0x30000000>;
+};
+
+&scb {
+	ranges = <0x0 0x7c000000  0x0 0xfc000000  0x0 0x03800000>,
+		 <0x0 0x40000000  0x0 0xff800000  0x0 0x00800000>,
+		 <0x6 0x00000000  0x6 0x00000000  0x0 0x40000000>,
+		 <0x0 0x00000000  0x0 0x00000000  0x0 0xfc000000>;
+	dma-ranges = <0x0 0x00000000  0x0 0x00000000  0x4 0x00000000>;
+
+	dma40: dma@7e007b00 {
+		compatible = "brcm,bcm2711-dma";
+		reg = <0x0 0x7e007b00  0x0 0x400>;
+		interrupts =
+			<GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>, /* dma4 11 */
+			<GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>, /* dma4 12 */
+			<GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>, /* dma4 13 */
+			<GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; /* dma4 14 */
+		interrupt-names = "dma11",
+			"dma12",
+			"dma13",
+			"dma14";
+		#dma-cells = <1>;
+		brcm,dma-channel-mask = <0x7800>;
+	};
+
+	xhci: xhci@7e9c0000 {
+		compatible = "generic-xhci";
+		status = "disabled";
+		reg = <0x0 0x7e9c0000  0x0 0x100000>;
+		interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&power RPI_POWER_DOMAIN_USB>;
+	};
+
+	hevc-decoder@7eb00000 {
+		compatible = "raspberrypi,rpivid-hevc-decoder";
+		reg = <0x0 0x7eb00000  0x0 0x10000>;
+		status = "okay";
+	};
+
+	rpivid-local-intc@7eb10000 {
+		compatible = "raspberrypi,rpivid-local-intc";
+		reg = <0x0 0x7eb10000  0x0 0x1000>;
+		status = "okay";
+		interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	h264-decoder@7eb20000 {
+		compatible = "raspberrypi,rpivid-h264-decoder";
+		reg = <0x0 0x7eb20000  0x0 0x10000>;
+		status = "okay";
+	};
+
+	vp9-decoder@7eb30000 {
+		compatible = "raspberrypi,rpivid-vp9-decoder";
+		reg = <0x0 0x7eb30000  0x0 0x10000>;
+		status = "okay";
+	};
+};
+
+&dma40 {
+	/* The VPU firmware uses DMA channel 11 for VCHIQ */
+	brcm,dma-channel-mask = <0x7000>;
+};
+
+&vchiq {
+	compatible = "brcm,bcm2711-vchiq";
+};
+
+&firmwarekms {
+	compatible = "raspberrypi,rpi-firmware-kms-2711";
+	interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&smi {
+	interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&mmc {
+	interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&mmcnr {
+	interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&csi0 {
+	interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&csi1 {
+	interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&random {
+	compatible = "brcm,bcm2711-rng200";
+	status = "okay";
+};
+
+&usb {
+	/* Enable the FIQ support */
+	reg = <0x7e980000 0x10000>,
+	      <0x7e00b200 0x200>;
+	interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+	status = "disabled";
+};
+
+&gpio {
+	interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&emmc2 {
+	mmc-ddr-3_3v;
+};
+
+&vc4 {
+	status = "disabled";
+};
+
+&pixelvalve0 {
+	status = "disabled";
+};
+
+&pixelvalve1 {
+	status = "disabled";
+};
+
+&pixelvalve2 {
+	status = "disabled";
+};
+
+&pixelvalve3 {
+	status = "disabled";
+};
+
+&pixelvalve4 {
+	status = "disabled";
+};
+
+&hdmi0 {
+	dmas = <&dma (10|(1<<27))>;
+	status = "disabled";
+};
+
+&ddc0 {
+	status = "disabled";
+};
+
+&hdmi1 {
+	dmas = <&dma (17|(1<<27))>;
+	status = "disabled";
+};
+
+&ddc1 {
+	status = "disabled";
+};
+
+&dvp {
+	status = "disabled";
+};

arch/arm/boot/dts/bcm2711.dtsi

@@ -318,7 +318,8 @@
 			      <0x7ef01f00 0x400>,
 			      <0x7ef00200 0x80>,
 			      <0x7ef04300 0x100>,
-			      <0x7ef20000 0x100>;
+			      <0x7ef20000 0x100>,
+			      <0x7ef00100 0x30>;
 			reg-names = "hdmi",
 				    "dvp",
 				    "phy",
@@ -327,12 +328,18 @@
 				    "metadata",
 				    "csc",
 				    "cec",
-				    "hd";
+				    "hd",
+				    "intr2";
+			clocks = <&firmware_clocks 13>,
+				 <&firmware_clocks 14>,
+				 <&dvp 0>,
+				 <&clk_27MHz>;
 			clock-names = "hdmi", "bvb", "audio", "cec";
 			resets = <&dvp 0>;
 			ddc = <&ddc0>;
 			dmas = <&dma 10>;
 			dma-names = "audio-rx";
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 		};
 
@@ -354,7 +361,8 @@
 			      <0x7ef06f00 0x400>,
 			      <0x7ef00280 0x80>,
 			      <0x7ef09300 0x100>,
-			      <0x7ef20000 0x100>;
+			      <0x7ef20000 0x100>,
+			      <0x7ef00100 0x30>;
 			reg-names = "hdmi",
 				    "dvp",
 				    "phy",
@@ -363,12 +371,18 @@
 				    "metadata",
 				    "csc",
 				    "cec",
-				    "hd";
+				    "hd",
+				    "intr2";
 			ddc = <&ddc1>;
 			clock-names = "hdmi", "bvb", "audio", "cec";
+			clocks = <&firmware_clocks 13>,
+				 <&firmware_clocks 14>,
+				 <&dvp 0>,
+				 <&clk_27MHz>;
 			resets = <&dvp 1>;
 			dmas = <&dma 17>;
 			dma-names = "audio-rx";
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 		};
 
@@ -468,14 +482,14 @@
 	scb {
 		compatible = "simple-bus";
 		#address-cells = <2>;
-		#size-cells = <1>;
+		#size-cells = <2>;
 
-		ranges = <0x0 0x7c000000  0x0 0xfc000000  0x03800000>,
-			 <0x6 0x00000000  0x6 0x00000000  0x40000000>;
+		ranges = <0x0 0x7c000000  0x0 0xfc000000  0x0 0x03800000>,
+			 <0x6 0x00000000  0x6 0x00000000  0x0 0x40000000>;
 
 		pcie0: pcie@7d500000 {
 			compatible = "brcm,bcm2711-pcie";
-			reg = <0x0 0x7d500000 0x9310>;
+			reg = <0x0 0x7d500000  0x0 0x9310>;
 			device_type = "pci";
 			#address-cells = <3>;
 			#interrupt-cells = <1>;
@@ -503,7 +517,7 @@
 
 		genet: ethernet@7d580000 {
 			compatible = "brcm,bcm2711-genet-v5";
-			reg = <0x0 0x7d580000 0x10000>;
+			reg = <0x0 0x7d580000  0x0 0x10000>;
 			#address-cells = <0x1>;
 			#size-cells = <0x1>;
 			interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>,
@@ -1010,7 +1024,7 @@
 	alloc-ranges = <0x0 0x00000000 0x40000000>;
 };
 
-&i2c0 {
+&i2c0if {
 	compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c";
 	interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
 };

arch/arm/boot/dts/bcm271x-rpi-bt.dtsi

+// SPDX-License-Identifier: GPL-2.0
+
+&uart0 {
+	bt: bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <3000000>;
+		shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+	};
+};
+
+&uart1 {
+	minibt: bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <460800>;
+		shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+	};
+};
+
+/ {
+	__overrides__ {
+		krnbt = <&bt>,"status";
+		krnbt_baudrate = <&bt>,"max-speed:0";
+	};
+};

arch/arm/boot/dts/bcm2835-common.dtsi

@@ -116,12 +116,14 @@
 			compatible = "brcm,bcm2835-hdmi";
 			reg = <0x7e902000 0x600>,
 			      <0x7e808000 0x100>;
+			reg-names = "hdmi",
+				    "hd";
 			interrupts = <2 8>, <2 9>;
 			ddc = <&i2c2>;
 			clocks = <&clocks BCM2835_PLLH_PIX>,
 				 <&clocks BCM2835_CLOCK_HSM>;
 			clock-names = "pixel", "hdmi";
-			dmas = <&dma 17>;
+			dmas = <&dma (17|(1<<27))>;
 			dma-names = "audio-rx";
 			status = "disabled";
 		};

arch/arm/boot/dts/bcm2835-rpi-a-plus.dts

@@ -126,3 +126,8 @@
 	pinctrl-0 = <&uart0_gpio14>;
 	status = "okay";
 };
+
+/* i2c on camera/display connector is gpio 28&29 */
+&i2c0mux {
+	pinctrl-1 = <&i2c0_gpio28>;
+};

arch/arm/boot/dts/bcm2835-rpi-a.dts

@@ -121,3 +121,10 @@
 	pinctrl-0 = <&uart0_gpio14>;
 	status = "okay";
 };
+
+/* i2c0 on camera/display connector is gpio 0&1. Not exposed on header.
+ * To avoid having to remap everything, map both ports to gpios 0&1
+ */
+&i2c0mux {
+	pinctrl-1 = <&i2c0_gpio0>;
+};

arch/arm/boot/dts/bcm2835-rpi-b-plus.dts

@@ -128,3 +128,8 @@
 	pinctrl-0 = <&uart0_gpio14>;
 	status = "okay";
 };
+
+/* i2c on camera/display connector is gpio 28&29 */
+&i2c0mux {
+	pinctrl-1 = <&i2c0_gpio28>;
+};

arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts

@@ -121,3 +121,10 @@
 	pinctrl-0 = <&uart0_gpio14>;
 	status = "okay";
 };
+
+/* i2c0 on camera/display connector is gpio 0&1. Not exposed on header.
+ * To avoid having to remap everything, map both ports to gpios 0&1
+ */
+&i2c0mux {
+	pinctrl-1 = <&i2c0_gpio0>;
+};

arch/arm/boot/dts/bcm2835-rpi-b.dts

@@ -116,3 +116,10 @@
 	pinctrl-0 = <&uart0_gpio14>;
 	status = "okay";
 };
+
+/* camera/display connector use BSC1 on GPIOS 2&3.
+ * To avoid having to remap everything, map both ports to gpios 0&1
+ */
+&i2c0mux {
+	pinctrl-1 = <&i2c0_gpio0>;
+};

arch/arm/boot/dts/bcm2835-rpi-cm1-io1.dts

@@ -95,3 +95,8 @@
 	pinctrl-0 = <&uart0_gpio14>;
 	status = "okay";
 };
+
+/* WHAT TO DO HERE? */
+&i2c0mux {
+	pinctrl-1 = <&i2c0_gpio28>;
+};

arch/arm/boot/dts/bcm2835-rpi-zero-w.dts

@@ -149,3 +149,8 @@
 	pinctrl-0 = <&uart1_gpio14>;
 	status = "okay";
 };
+
+/* i2c on camera/display connector is gpio 28&29 */
+&i2c0mux {
+	pinctrl-1 = <&i2c0_gpio28>;
+};

arch/arm/boot/dts/bcm2835-rpi-zero.dts

@@ -117,3 +117,8 @@
 	pinctrl-0 = <&uart0_gpio14>;
 	status = "okay";
 };
+
+/* i2c on camera/display connector is gpio 28&29 */
+&i2c0mux {
+	pinctrl-1 = <&i2c0_gpio28>;
+};

arch/arm/boot/dts/bcm2835-rpi.dtsi

@@ -19,6 +19,11 @@
 
 			mboxes = <&mailbox>;
 			dma-ranges;
+
+			firmware_clocks: clocks {
+				compatible = "raspberrypi,firmware-clocks";
+				#clock-cells = <1>;
+			};
 		};
 
 		power: power {
@@ -49,13 +54,17 @@
 	};
 };
 
-&i2c0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c0_gpio0>;
+&i2c0if {
 	status = "okay";
 	clock-frequency = <100000>;
 };
 
+&i2c0mux {
+	pinctrl-0 = <&i2c0_gpio0>;
+	/* pinctrl-1 varies based on platform */
+	status = "okay";
+};
+
 &i2c1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c1_gpio2>;

arch/arm/boot/dts/bcm2835.dtsi

@@ -19,7 +19,7 @@
 
 	soc {
 		ranges = <0x7e000000 0x20000000 0x02000000>;
-		dma-ranges = <0x40000000 0x00000000 0x20000000>;
+		dma-ranges = <0x80000000 0x00000000 0x20000000>;
 	};
 
 	arm-pmu {

arch/arm/boot/dts/bcm2836-rpi-2-b.dts

@@ -128,3 +128,8 @@
 	pinctrl-0 = <&uart0_gpio14>;
 	status = "okay";
 };
+
+/* i2c on camera/display connector is gpio 28&29 */
+&i2c0mux {
+	pinctrl-1 = <&i2c0_gpio28>;
+};

arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts

@@ -178,3 +178,8 @@
 	pinctrl-0 = <&uart1_gpio14>;
 	status = "okay";
 };
+
+/* i2c on camera/display connector is gpio 44&45 */
+&i2c0mux {
+	pinctrl-1 = <&i2c0_gpio44>;
+};

arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts

@@ -181,3 +181,8 @@
 	pinctrl-0 = <&uart1_gpio14>;
 	status = "okay";
 };
+
+/* i2c on camera/display connector is gpio 44&45 */
+&i2c0mux {
+	pinctrl-1 = <&i2c0_gpio44>;
+};

arch/arm/boot/dts/bcm2837-rpi-3-b.dts

@@ -174,3 +174,8 @@
 	status = "okay";
 	bus-width = <4>;
 };
+
+/* i2c on camera/display connector is gpio 44&45 */
+&i2c0mux {
+	pinctrl-1 = <&i2c0_gpio44>;
+};

arch/arm/boot/dts/bcm2837-rpi-cm3-io3.dts

@@ -94,3 +94,8 @@
 	pinctrl-0 = <&uart0_gpio14>;
 	status = "okay";
 };
+
+/* WHAT TO DO HERE? */
+&i2c0mux {
+	pinctrl-1 = <&i2c0_gpio28>;
+};

arch/arm/boot/dts/bcm283x-rpi-csi0-2lane.dtsi

+// SPDX-License-Identifier: GPL-2.0-only
+&csi0 {
+	brcm,num-data-lanes = <2>;
+};

arch/arm/boot/dts/bcm283x-rpi-csi1-2lane.dtsi

+// SPDX-License-Identifier: GPL-2.0-only
+&csi1 {
+	brcm,num-data-lanes = <2>;
+};

arch/arm/boot/dts/bcm283x-rpi-csi1-4lane.dtsi

+// SPDX-License-Identifier: GPL-2.0-only
+&csi1 {
+	brcm,num-data-lanes = <4>;
+};

arch/arm/boot/dts/bcm283x-rpi-i2c0mux_0_28.dtsi

+&i2c0mux {
+	pinctrl-0 = <&i2c0_gpio0>;
+	pinctrl-1 = <&i2c0_gpio28>;
+};

arch/arm/boot/dts/bcm283x-rpi-i2c0mux_0_44.dtsi

+&i2c0mux {
+	pinctrl-0 = <&i2c0_gpio0>;
+	pinctrl-1 = <&i2c0_gpio44>;
+};

arch/arm/boot/dts/bcm283x-rpi-usb-peripheral.dtsi

-// SPDX-License-Identifier: GPL-2.0
-&usb {
-	dr_mode = "peripheral";
-	g-rx-fifo-size = <256>;
-	g-np-tx-fifo-size = <32>;
-	g-tx-fifo-size = <256 256 512 512 512 768 768>;
-};

arch/arm/boot/dts/bcm283x.dtsi

@@ -334,7 +334,7 @@
 			status = "disabled";
 		};
 
-		i2c0: i2c@7e205000 {
+		i2c0if: i2c@7e205000 {
 			compatible = "brcm,bcm2835-i2c";
 			reg = <0x7e205000 0x200>;
 			interrupts = <2 21>;
@@ -344,6 +344,30 @@
 			status = "disabled";
 		};
 
+		i2c0mux: i2c0mux {
+			compatible = "i2c-mux-pinctrl";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			i2c-parent = <&i2c0if>;
+
+			pinctrl-names = "i2c0", "i2c_csi_dsi";
+
+			status = "disabled";
+
+			i2c0: i2c@0 {
+				reg = <0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			i2c_csi_dsi: i2c@1 {
+				reg = <1>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
 		dpi: dpi@7e208000 {
 			compatible = "brcm,bcm2835-dpi";
 			reg = <0x7e208000 0x8c>;

arch/arm/boot/dts/overlays/Makefile

+# Overlays for the Raspberry Pi platform
+
+dtb-$(CONFIG_ARCH_BCM2835) += overlay_map.dtb
+
+dtbo-$(CONFIG_ARCH_BCM2835) += \
+	act-led.dtbo \
+	adafruit18.dtbo \
+	adau1977-adc.dtbo \
+	adau7002-simple.dtbo \
+	ads1015.dtbo \
+	ads1115.dtbo \
+	ads7846.dtbo \
+	adv7282m.dtbo \
+	adv728x-m.dtbo \
+	akkordion-iqdacplus.dtbo \
+	allo-boss-dac-pcm512x-audio.dtbo \
+	allo-digione.dtbo \
+	allo-katana-dac-audio.dtbo \
+	allo-piano-dac-pcm512x-audio.dtbo \
+	allo-piano-dac-plus-pcm512x-audio.dtbo \
+	anyspi.dtbo \
+	apds9960.dtbo \
+	applepi-dac.dtbo \
+	at86rf233.dtbo \
+	audioinjector-addons.dtbo \
+	audioinjector-isolated-soundcard.dtbo \
+	audioinjector-ultra.dtbo \
+	audioinjector-wm8731-audio.dtbo \
+	audiosense-pi.dtbo \
+	audremap.dtbo \
+	balena-fin.dtbo \
+	cma.dtbo \
+	dht11.dtbo \
+	dionaudio-loco.dtbo \
+	dionaudio-loco-v2.dtbo \
+	disable-bt.dtbo \
+	disable-wifi.dtbo \
+	dpi18.dtbo \
+	dpi24.dtbo \
+	draws.dtbo \
+	dwc-otg.dtbo \
+	dwc2.dtbo \
+	enc28j60.dtbo \
+	enc28j60-spi2.dtbo \
+	exc3000.dtbo \
+	fe-pi-audio.dtbo \
+	fsm-demo.dtbo \
+	ghost-amp.dtbo \
+	goodix.dtbo \
+	googlevoicehat-soundcard.dtbo \
+	gpio-fan.dtbo \
+	gpio-ir.dtbo \
+	gpio-ir-tx.dtbo \
+	gpio-key.dtbo \
+	gpio-no-bank0-irq.dtbo \
+	gpio-no-irq.dtbo \
+	gpio-poweroff.dtbo \
+	gpio-shutdown.dtbo \
+	hd44780-lcd.dtbo \
+	hdmi-backlight-hwhack-gpio.dtbo \
+	hifiberry-amp.dtbo \
+	hifiberry-dac.dtbo \
+	hifiberry-dacplus.dtbo \
+	hifiberry-dacplusadc.dtbo \
+	hifiberry-dacplusadcpro.dtbo \
+	hifiberry-dacplusdsp.dtbo \
+	hifiberry-dacplushd.dtbo \
+	hifiberry-digi.dtbo \
+	hifiberry-digi-pro.dtbo \
+	highperi.dtbo \
+	hy28a.dtbo \
+	hy28b.dtbo \
+	hy28b-2017.dtbo \
+	i-sabre-q2m.dtbo \
+	i2c-bcm2708.dtbo \
+	i2c-gpio.dtbo \
+	i2c-mux.dtbo \
+	i2c-pwm-pca9685a.dtbo \
+	i2c-rtc.dtbo \
+	i2c-rtc-gpio.dtbo \
+	i2c-sensor.dtbo \
+	i2c0.dtbo \
+	i2c1.dtbo \
+	i2c3.dtbo \
+	i2c4.dtbo \
+	i2c5.dtbo \
+	i2c6.dtbo \
+	i2s-gpio28-31.dtbo \
+	ilitek251x.dtbo \
+	imx219.dtbo \
+	imx290.dtbo \
+	imx477.dtbo \
+	iqaudio-codec.dtbo \
+	iqaudio-dac.dtbo \
+	iqaudio-dacplus.dtbo \
+	iqaudio-digi-wm8804-audio.dtbo \
+	irs1125.dtbo \
+	jedec-spi-nor.dtbo \
+	justboom-both.dtbo \
+	justboom-dac.dtbo \
+	justboom-digi.dtbo \
+	ltc294x.dtbo \
+	max98357a.dtbo \
+	maxtherm.dtbo \
+	mbed-dac.dtbo \
+	mcp23017.dtbo \
+	mcp23s17.dtbo \
+	mcp2515-can0.dtbo \
+	mcp2515-can1.dtbo \
+	mcp3008.dtbo \
+	mcp3202.dtbo \
+	mcp342x.dtbo \
+	media-center.dtbo \
+	merus-amp.dtbo \
+	midi-uart0.dtbo \
+	midi-uart1.dtbo \
+	miniuart-bt.dtbo \
+	mmc.dtbo \
+	mpu6050.dtbo \
+	mz61581.dtbo \
+	ov5647.dtbo \
+	ov7251.dtbo \
+	ov9281.dtbo \
+	papirus.dtbo \
+	pca953x.dtbo \
+	pibell.dtbo \
+	pifacedigital.dtbo \
+	piglow.dtbo \
+	piscreen.dtbo \
+	piscreen2r.dtbo \
+	pisound.dtbo \
+	pitft22.dtbo \
+	pitft28-capacitive.dtbo \
+	pitft28-resistive.dtbo \
+	pitft35-resistive.dtbo \
+	pps-gpio.dtbo \
+	pwm.dtbo \
+	pwm-2chan.dtbo \
+	pwm-ir-tx.dtbo \
+	qca7000.dtbo \
+	rotary-encoder.dtbo \
+	rpi-backlight.dtbo \
+	rpi-cirrus-wm5102.dtbo \
+	rpi-dac.dtbo \
+	rpi-display.dtbo \
+	rpi-ft5406.dtbo \
+	rpi-poe.dtbo \
+	rpi-proto.dtbo \
+	rpi-sense.dtbo \
+	rpi-tv.dtbo \
+	rpivid-v4l2.dtbo \
+	rra-digidac1-wm8741-audio.dtbo \
+	sainsmart18.dtbo \
+	sc16is750-i2c.dtbo \
+	sc16is752-i2c.dtbo \
+	sc16is752-spi0.dtbo \
+	sc16is752-spi1.dtbo \
+	sdhost.dtbo \
+	sdio.dtbo \
+	sdtweak.dtbo \
+	sh1106-spi.dtbo \
+	smi.dtbo \
+	smi-dev.dtbo \
+	smi-nand.dtbo \
+	spi-gpio35-39.dtbo \
+	spi-gpio40-45.dtbo \
+	spi-rtc.dtbo \
+	spi0-1cs.dtbo \
+	spi0-2cs.dtbo \
+	spi1-1cs.dtbo \
+	spi1-2cs.dtbo \
+	spi1-3cs.dtbo \
+	spi2-1cs.dtbo \
+	spi2-2cs.dtbo \
+	spi2-3cs.dtbo \
+	spi3-1cs.dtbo \
+	spi3-2cs.dtbo \
+	spi4-1cs.dtbo \
+	spi4-2cs.dtbo \
+	spi5-1cs.dtbo \
+	spi5-2cs.dtbo \
+	spi6-1cs.dtbo \
+	spi6-2cs.dtbo \
+	ssd1306.dtbo \
+	ssd1306-spi.dtbo \
+	ssd1351-spi.dtbo \
+	superaudioboard.dtbo \
+	sx150x.dtbo \
+	tc358743.dtbo \
+	tc358743-audio.dtbo \
+	tinylcd35.dtbo \
+	tpm-slb9670.dtbo \
+	uart0.dtbo \
+	uart1.dtbo \
+	uart2.dtbo \
+	uart3.dtbo \
+	uart4.dtbo \
+	uart5.dtbo \
+	udrc.dtbo \
+	upstream.dtbo \
+	upstream-pi4.dtbo \
+	vc4-fkms-v3d.dtbo \
+	vc4-kms-kippah-7inch.dtbo \
+	vc4-kms-v3d.dtbo \
+	vc4-kms-v3d-pi4.dtbo \
+	vga666.dtbo \
+	w1-gpio.dtbo \
+	w1-gpio-pullup.dtbo \
+	w5500.dtbo \
+	wittypi.dtbo
+
+targets += dtbs dtbs_install
+targets += $(dtbo-y)
+
+always-y	:= $(dtbo-y)
+clean-files	:= *.dtbo

arch/arm/boot/dts/overlays/act-led-overlay.dts

+/dts-v1/;
+/plugin/;
+
+/* Pi3 uses a GPIO expander to drive the LEDs which can only be accessed
+   from the VPU. There is a special driver for this with a separate DT node,
+   which has the unfortunate consequence of breaking the act_led_gpio and
+   act_led_activelow dtparams.
+
+   This overlay changes the GPIO controller back to the standard one and
+   restores the dtparams.
+*/
+
+/{
+	compatible = "brcm,bcm2835";
+
+	fragment@0 {
+		target = <&act_led>;
+		frag0: __overlay__ {
+			gpios = <&gpio 0 0>;
+		};
+	};
+
+	__overrides__ {
+		gpio = <&frag0>,"gpios:4";
+		activelow = <&frag0>,"gpios:8";
+	};
+};

arch/arm/boot/dts/overlays/adafruit18-overlay.dts

+/*
+ * Device Tree overlay for Adafruit 1.8" TFT LCD with ST7735R chip 160x128
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835";
+
+	fragment@0 {
+		target = <&spidev0>;
+		__overlay__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@1 {
+		target = <&spi0>;
+		__overlay__ {
+			/* needed to avoid dtc warning */
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			af18: adafruit18@0 {
+				compatible = "fbtft,adafruit18";
+				reg = <0>;
+				pinctrl-names = "default";
+				spi-max-frequency = <40000000>;
+				rotate = <90>;
+				buswidth = <8>;
+				fps = <50>;
+				height = <160>;
+				width = <128>;
+				reset-gpios = <&gpio 25 1>;
+				dc-gpios = <&gpio 24 0>;
+				led-gpios = <&gpio 18 0>;
+				debug = <0>;
+			};
+		};
+	};
+
+	__overrides__ {
+		green = <&af18>, "compatible=fbtft,adafruit18_green";
+		speed     = <&af18>,"spi-max-frequency:0";
+		rotate    = <&af18>,"rotate:0";
+		fps       = <&af18>,"fps:0";
+		bgr       = <&af18>,"bgr?";
+		debug     = <&af18>,"debug:0";
+		dc_pin    = <&af18>,"dc-gpios:4";
+		reset_pin = <&af18>,"reset-gpios:4";
+		led_pin   = <&af18>,"led-gpios:4";
+	};
+};

arch/arm/boot/dts/overlays/adau1977-adc-overlay.dts

+// Definitions for ADAU1977 ADC
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835";
+    
+	fragment@0 {
+        	target = <&i2c>;
+        	
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+			
+			adau1977: codec@11 {
+                        	compatible = "adi,adau1977";
+                        	reg = <0x11>;
+                        	reset-gpios = <&gpio 5 0>;
+				AVDD-supply = <&vdd_3v3_reg>;
+                	};
+        	};
+	};
+
+	fragment@1 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@2 {
+		target = <&sound>;
+		__overlay__ {
+			compatible = "adi,adau1977-adc";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+};

arch/arm/boot/dts/overlays/adau7002-simple-overlay.dts

+/dts-v1/;
+/plugin/;
+
+/ {
+    compatible = "brcm,bcm2835";
+
+    fragment@0 {
+        target = <&i2s>;
+        __overlay__ {
+            status = "okay";
+        };
+    };
+
+    fragment@1 {
+        target-path = "/";
+        __overlay__ {
+                adau7002_codec: adau7002-codec {
+                #sound-dai-cells = <0>;
+                compatible = "adi,adau7002";
+/*                IOVDD-supply = <&supply>;*/
+                status = "okay";
+            };
+        };
+    };
+
+    fragment@2 {
+        target = <&sound>;
+            sound_overlay: __overlay__ {
+            compatible = "simple-audio-card";
+            simple-audio-card,format = "i2s";
+            simple-audio-card,name = "adau7002";
+            simple-audio-card,bitclock-slave = <&dailink0_slave>;
+            simple-audio-card,frame-slave = <&dailink0_slave>;
+            simple-audio-card,widgets =
+                    "Microphone", "Microphone Jack";
+            simple-audio-card,routing =
+                    "PDM_DAT", "Microphone Jack";
+            status = "okay";
+            simple-audio-card,cpu {
+                sound-dai = <&i2s>;
+            };
+            dailink0_slave: simple-audio-card,codec {
+                sound-dai = <&adau7002_codec>;
+            };
+        };
+    };
+
+
+    __overrides__ {
+        card-name = <&sound_overlay>,"simple-audio-card,name";
+    };
+};

arch/arm/boot/dts/overlays/ads1015-overlay.dts

+/*
+ * 2016 - Erik Sejr
+ */
+/dts-v1/;
+/plugin/;
+
+/ {
+    compatible = "brcm,bcm2835";
+    /* ----------- ADS1015 ------------ */
+    fragment@0 {
+        target = <&i2c_arm>;
+        __overlay__ {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            status = "okay";
+            ads1015: ads1015 {
+                compatible = "ti,ads1015";
+                status = "okay";
+                #address-cells = <1>;
+                #size-cells = <0>;
+                reg = <0x48>;
+            };
+        };
+    };
+
+    fragment@1 {
+        target = <&ads1015>;
+        __overlay__ {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            channel_a: channel_a {
+                reg = <4>;
+                ti,gain = <2>;
+                ti,datarate = <4>;
+            };
+        };
+    };
+
+    fragment@2 {
+        target = <&ads1015>;
+        __dormant__ {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            channel_b: channel_b {
+                reg = <5>;
+                ti,gain = <2>;
+                ti,datarate = <4>;
+            };
+        };
+    };
+
+    fragment@3 {
+        target = <&ads1015>;
+        __dormant__ {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            channel_c: channel_c {
+                reg = <6>;
+                ti,gain = <2>;
+                ti,datarate = <4>;
+            };
+        };
+    };
+
+    fragment@4 {
+        target = <&ads1015>;
+        __dormant__ {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            channel_d: channel_d {
+                reg = <7>;
+                ti,gain = <2>;
+                ti,datarate = <4>;
+            };
+        };
+    };
+
+    __overrides__ {
+        addr =            <&ads1015>,"reg:0";
+        cha_enable =      <0>,"=1";
+        cha_cfg =         <&channel_a>,"reg:0";
+        cha_gain =        <&channel_a>,"ti,gain:0";
+        cha_datarate =    <&channel_a>,"ti,datarate:0";
+        chb_enable =      <0>,"=2";
+        chb_cfg =         <&channel_b>,"reg:0";
+        chb_gain =        <&channel_b>,"ti,gain:0";
+        chb_datarate =    <&channel_b>,"ti,datarate:0";
+        chc_enable =      <0>,"=3";
+        chc_cfg =         <&channel_c>,"reg:0";
+        chc_gain =        <&channel_c>,"ti,gain:0";
+        chc_datarate =    <&channel_c>,"ti,datarate:0";
+        chd_enable =      <0>,"=4";
+        chd_cfg =         <&channel_d>,"reg:0";
+        chd_gain =        <&channel_d>,"ti,gain:0";
+        chd_datarate =    <&channel_d>,"ti,datarate:0";
+   };
+
+};

arch/arm/boot/dts/overlays/ads1115-overlay.dts

+/*
+ * TI ADS1115 multi-channel ADC overlay
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835";
+
+	fragment@0 {
+		target = <&i2c_arm>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			ads1115: ads1115 {
+				compatible = "ti,ads1115";
+				status = "okay";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x48>;
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&ads1115>;
+		__dormant__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel_a: channel_a {
+				reg = <4>;
+				ti,gain = <1>;
+				ti,datarate = <7>;
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&ads1115>;
+		__dormant__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel_b: channel_b {
+				reg = <5>;
+				ti,gain = <1>;
+				ti,datarate = <7>;
+			};
+		};
+	};
+
+	fragment@3 {
+		target = <&ads1115>;
+		__dormant__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel_c: channel_c {
+				reg = <6>;
+				ti,gain = <1>;
+				ti,datarate = <7>;
+			};
+		};
+	};
+
+	fragment@4 {
+		target = <&ads1115>;
+		__dormant__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel_d: channel_d {
+				reg = <7>;
+				ti,gain = <1>;
+				ti,datarate = <7>;
+			};
+		};
+	};
+
+	__overrides__ {
+		addr =            <&ads1115>,"reg:0";
+		cha_enable =      <0>,"=1";
+		cha_cfg =         <&channel_a>,"reg:0";
+		cha_gain =        <&channel_a>,"ti,gain:0";
+		cha_datarate =    <&channel_a>,"ti,datarate:0";
+		chb_enable =      <0>,"=2";
+		chb_cfg =         <&channel_b>,"reg:0";
+		chb_gain =        <&channel_b>,"ti,gain:0";
+		chb_datarate =    <&channel_b>,"ti,datarate:0";
+		chc_enable =      <0>,"=3";
+		chc_cfg =         <&channel_c>,"reg:0";
+		chc_gain =        <&channel_c>,"ti,gain:0";
+		chc_datarate =    <&channel_c>,"ti,datarate:0";
+		chd_enable =      <0>,"=4";
+		chd_cfg =         <&channel_d>,"reg:0";
+		chd_gain =        <&channel_d>,"ti,gain:0";
+		chd_datarate =    <&channel_d>,"ti,datarate:0";
+	};
+};

arch/arm/boot/dts/overlays/ads7846-overlay.dts

+/*
+ * Generic Device Tree overlay for the ADS7846 touch controller
+ *
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835";
+
+	fragment@0 {
+		target = <&spi0>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&spidev0>;
+		__overlay__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@2 {
+		target = <&spidev1>;
+		__overlay__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@3 {
+		target = <&gpio>;
+		__overlay__ {
+			ads7846_pins: ads7846_pins {
+				brcm,pins = <255>; /* illegal default value */
+				brcm,function = <0>; /* in */
+				brcm,pull = <0>; /* none */
+			};
+		};
+	};
+
+	fragment@4 {
+		target = <&spi0>;
+		__overlay__ {
+			/* needed to avoid dtc warning */
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ads7846: ads7846@1 {
+				compatible = "ti,ads7846";
+				reg = <1>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&ads7846_pins>;
+
+				spi-max-frequency = <2000000>;
+				interrupts = <255 2>; /* high-to-low edge triggered */
+				interrupt-parent = <&gpio>;
+				pendown-gpio = <&gpio 255 0>;
+
+				/* driver defaults */
+				ti,x-min = /bits/ 16 <0>;
+				ti,y-min = /bits/ 16 <0>;
+				ti,x-max = /bits/ 16 <0x0FFF>;
+				ti,y-max = /bits/ 16 <0x0FFF>;
+				ti,pressure-min = /bits/ 16 <0>;
+				ti,pressure-max = /bits/ 16 <0xFFFF>;
+				ti,x-plate-ohms = /bits/ 16 <400>;
+			};
+		};
+	};
+	__overrides__ {
+		cs =     <&ads7846>,"reg:0";
+		speed =  <&ads7846>,"spi-max-frequency:0";
+		penirq = <&ads7846_pins>,"brcm,pins:0", /* REQUIRED */
+			 <&ads7846>,"interrupts:0",
+			 <&ads7846>,"pendown-gpio:4";
+		penirq_pull = <&ads7846_pins>,"brcm,pull:0";
+		swapxy = <&ads7846>,"ti,swap-xy?";
+		xmin =   <&ads7846>,"ti,x-min;0";
+		ymin =   <&ads7846>,"ti,y-min;0";
+		xmax =   <&ads7846>,"ti,x-max;0";
+		ymax =   <&ads7846>,"ti,y-max;0";
+		pmin =   <&ads7846>,"ti,pressure-min;0";
+		pmax =   <&ads7846>,"ti,pressure-max;0";
+		xohms =  <&ads7846>,"ti,x-plate-ohms;0";
+	};
+};

arch/arm/boot/dts/overlays/adv7282m-overlay.dts

+// SPDX-License-Identifier: GPL-2.0-only
+// Definitions for Analog Devices ADV7282-M video to CSI2 bridge on VC I2C bus
+/dts-v1/;
+/plugin/;
+
+/{
+	compatible = "brcm,bcm2835";
+
+	fragment@0 {
+		target = <&i2c_csi_dsi>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			adv728x: adv728x@21 {
+				compatible = "adi,adv7282-m";
+				reg = <0x21>;
+				status = "okay";
+				clock-frequency = <24000000>;
+				port {
+					adv728x_0: endpoint {
+						remote-endpoint = <&csi1_ep>;
+						clock-lanes = <0>;
+						data-lanes = <1>;
+						link-frequencies =
+							/bits/ 64 <297000000>;
+
+						mclk-frequency = <12000000>;
+					};
+				};
+			};
+		};
+	};
+	fragment@1 {
+		target = <&csi1>;
+		__overlay__ {
+			status = "okay";
+
+			port {
+				csi1_ep: endpoint {
+					remote-endpoint = <&adv728x_0>;
+					data-lanes = <1>;
+				};
+			};
+		};
+	};
+	fragment@2 {
+		target = <&i2c0if>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@3 {
+		target = <&i2c0mux>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	__overrides__ {
+		addr =			<&adv728x>,"reg:0";
+	};
+};

arch/arm/boot/dts/overlays/adv728x-m-overlay.dts

+// SPDX-License-Identifier: GPL-2.0-only
+// Definitions for Analog Devices ADV728[0|1|2]-M video to CSI2 bridges on VC
+// I2C bus
+
+#include "adv7282m-overlay.dts"
+
+/{
+	compatible = "brcm,bcm2835";
+
+	// Fragment numbers deliberately high to avoid conflicts with the
+	// included adv7282m overlay file.
+
+	fragment@101 {
+		target = <&adv728x>;
+		__dormant__ {
+			compatible = "adi,adv7280-m";
+		};
+	};
+	fragment@102 {
+		target = <&adv728x>;
+		__dormant__ {
+			compatible = "adi,adv7281-m";
+		};
+	};
+	fragment@103 {
+		target = <&adv728x>;
+		__dormant__ {
+			compatible = "adi,adv7281-ma";
+		};
+	};
+
+	__overrides__ {
+		adv7280m = <0>, "+101";
+		adv7281m = <0>, "+102";
+		adv7281ma = <0>, "+103";
+	};
+};

arch/arm/boot/dts/overlays/akkordion-iqdacplus-overlay.dts

+// Definitions for Digital Dreamtime Akkordion using IQaudIO DAC+ or DACZero
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835";
+
+	fragment@0 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			pcm5122@4c {
+				#sound-dai-cells = <0>;
+				compatible = "ti,pcm5122";
+				reg = <0x4c>;
+				AVDD-supply = <&vdd_3v3_reg>;
+				DVDD-supply = <&vdd_3v3_reg>;
+				CPVDD-supply = <&vdd_3v3_reg>;
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&sound>;
+		frag2: __overlay__ {
+			compatible = "iqaudio,iqaudio-dac";
+			card_name = "Akkordion";
+			dai_name = "IQaudIO DAC";
+			dai_stream_name = "IQaudIO DAC HiFi";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+
+	__overrides__ {
+		24db_digital_gain = <&frag2>,"iqaudio,24db_digital_gain?";
+	};
+};

arch/arm/boot/dts/overlays/allo-boss-dac-pcm512x-audio-overlay.dts

+/*
+ * Definitions for Allo Boss DAC board
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835";
+
+	fragment@0 {
+		target-path = "/";
+		__overlay__ {
+			boss_osc: boss_osc {
+				compatible = "allo,dac-clk";
+				#clock-cells = <0>;
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@2 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			pcm5122@4d {
+				#sound-dai-cells = <0>;
+				compatible = "ti,pcm5122";
+				clocks = <&boss_osc>;
+				reg = <0x4d>;
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@3 {
+		target = <&sound>;
+		boss_dac: __overlay__ {
+			compatible = "allo,boss-dac";
+			i2s-controller = <&i2s>;
+			mute-gpios = <&gpio 6 1>;
+			status = "okay";
+		};
+	};
+
+	__overrides__ {
+		24db_digital_gain = <&boss_dac>,"allo,24db_digital_gain?";
+		slave = <&boss_dac>,"allo,slave?";
+	};
+};

arch/arm/boot/dts/overlays/allo-digione-overlay.dts

+// Definitions for Allo DigiOne
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835";
+
+	fragment@0 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			wm8804@3b {
+				#sound-dai-cells = <0>;
+				compatible = "wlf,wm8804";
+				reg = <0x3b>;
+				PVDD-supply = <&vdd_3v3_reg>;
+				DVDD-supply = <&vdd_3v3_reg>;
+				status = "okay";
+				wlf,reset-gpio = <&gpio 17 0>;
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&sound>;
+		__overlay__ {
+			compatible = "allo,allo-digione";
+			i2s-controller = <&i2s>;
+			status = "okay";
+			clock44-gpio = <&gpio 5 0>;
+			clock48-gpio = <&gpio 6 0>;
+		};
+	};
+};

arch/arm/boot/dts/overlays/allo-katana-dac-audio-overlay.dts

+/*
+ * Definitions for Allo Katana DAC boards
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835";
+
+	fragment@0 {
+		target = <&i2s>;
+		__overlay__ {
+			#sound-dai-cells = <0>;
+			status = "okay";
+			cpu_port: port {
+				cpu_endpoint: endpoint {
+					remote-endpoint = <&codec_endpoint>;
+					bitclock-master = <&codec_endpoint>;
+					frame-master = <&codec_endpoint>;
+					dai-format = "i2s";
+				};
+			};
+		};
+	};
+
+	fragment@1 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			allo-katana-codec@30 {
+				#sound-dai-cells = <0>;
+				compatible = "allo,allo-katana-codec";
+				reg = <0x30>;
+				port {
+					codec_endpoint: endpoint {
+					remote-endpoint = <&cpu_endpoint>;
+					};
+				};
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&sound>;
+		katana_dac: __overlay__ {
+			compatible = "audio-graph-card";
+			label = "Allo Katana";
+			dais = <&cpu_port>;
+			status = "okay";
+		};
+	};
+};
+

arch/arm/boot/dts/overlays/allo-piano-dac-pcm512x-audio-overlay.dts

+/*
+ * Definitions for Allo Piano DAC (2.0/2.1) boards
+ *
+ * NB. The Piano DAC 2.1 board contains 2x TI PCM5142 DAC's. One DAC is stereo
+ * (left/right) and the other provides a subwoofer output, using DSP on the
+ * chip for digital high/low pass crossover.
+ * The initial support for this hardware, that doesn't require any codec driver
+ * modifications, uses only one DAC chip for stereo (left/right) output, the
+ * chip with 0x4c slave address. The other chip at 0x4d is currently ignored!
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835";
+
+	fragment@0 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			pcm5142@4c {
+				#sound-dai-cells = <0>;
+				compatible = "ti,pcm5142";
+				reg = <0x4c>;
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&sound>;
+		piano_dac: __overlay__ {
+			compatible = "allo,piano-dac";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+
+	__overrides__ {
+		24db_digital_gain =
+			<&piano_dac>,"allo,24db_digital_gain?";
+	};
+};

arch/arm/boot/dts/overlays/allo-piano-dac-plus-pcm512x-audio-overlay.dts

+// Definitions for Piano DAC
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835";
+
+	fragment@0 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			allo_pcm5122_4c: pcm5122@4c {
+				#sound-dai-cells = <0>;
+				compatible = "ti,pcm5122";
+				reg = <0x4c>;
+				status = "okay";
+			};
+			allo_pcm5122_4d: pcm5122@4d {
+				#sound-dai-cells = <0>;
+				compatible = "ti,pcm5122";
+				reg = <0x4d>;
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&sound>;
+		piano_dac: __overlay__ {
+			compatible = "allo,piano-dac-plus";
+			audio-codec = <&allo_pcm5122_4c &allo_pcm5122_4d>;
+			i2s-controller = <&i2s>;
+			mute1-gpios = <&gpio 6 1>;
+			mute2-gpios = <&gpio 25 1>;
+			status = "okay";
+		};
+	};
+
+	__overrides__ {
+		24db_digital_gain =
+			<&piano_dac>,"allo,24db_digital_gain?";
+		glb_mclk =
+			<&piano_dac>,"allo,glb_mclk?";
+	};
+};

arch/arm/boot/dts/overlays/anyspi-overlay.dts

+/*
+ * Universal device tree overlay for SPI devices
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835";
+
+	fragment@0 {
+		target = <&spidev0>;
+		__dormant__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@1 {
+		target = <&spidev1>;
+		__dormant__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@2 {
+		target-path = "spi1/spidev@0";
+		__dormant__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@3 {
+		target-path = "spi1/spidev@1";
+		__dormant__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@4 {
+		target-path = "spi1/spidev@2";
+		__dormant__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@5 {
+		target-path = "spi2/spidev@0";
+		__dormant__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@6 {
+		target-path = "spi2/spidev@1";
+		__dormant__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@7 {
+		target-path = "spi2/spidev@2";
+		__dormant__ {
+			status = "disabled";
+		};
+	};
+
+	fragment@8 {
+		target = <&spi0>;
+		__dormant__ {
+			status = "okay";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			anyspi_00: anyspi@0 {
+				reg = <0>;
+				spi-max-frequency = <500000>;
+			};
+		};
+	};
+
+	fragment@9 {
+		target = <&spi0>;
+		__dormant__ {
+			status = "okay";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			anyspi_01: anyspi@1 {
+				reg = <1>;
+				spi-max-frequency = <500000>;
+			};
+		};
+	};
+
+	fragment@10 {
+		target = <&spi1>;
+		__dormant__ {
+			status = "okay";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			anyspi_10: anyspi@0 {
+				reg = <0>;
+				spi-max-frequency = <500000>;
+			};
+		};
+	};
+
+	fragment@11 {
+		target = <&spi1>;
+		__dormant__ {
+			status = "okay";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			anyspi_11: anyspi@1 {
+				reg = <1>;
+				spi-max-frequency = <500000>;
+			};
+		};
+	};
+
+	fragment@12 {
+		target = <&spi1>;
+		__dormant__ {
+			status = "okay";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			anyspi_12: anyspi@2 {
+				reg = <2>;
+				spi-max-frequency = <500000>;
+			};
+		};
+	};
+
+	fragment@13 {
+		target = <&spi2>;
+		__dormant__ {
+			status = "okay";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			anyspi_20: anyspi@0 {
+				reg = <0>;
+				spi-max-frequency = <500000>;
+			};
+		};
+	};
+
+	fragment@14 {
+		target = <&spi2>;
+		__dormant__ {
+			status = "okay";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			anyspi_21: anyspi@1 {
+				reg = <1>;
+				spi-max-frequency = <500000>;
+			};
+		};
+	};
+
+	fragment@15 {
+		target = <&spi2>;
+		__dormant__ {
+			status = "okay";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			anyspi_22: anyspi@2 {
+				reg = <2>;
+				spi-max-frequency = <500000>;
+			};
+		};
+	};
+
+	__overrides__ {
+		spi0-0 = <0>, "+0+8";
+		spi0-1 = <0>, "+1+9";
+		spi1-0 = <0>, "+2+10";
+		spi1-1 = <0>, "+3+11";
+		spi1-2 = <0>, "+4+12";
+		spi2-0 = <0>, "+5+13";
+		spi2-1 = <0>, "+6+14";
+		spi2-2 = <0>, "+7+15";
+		dev = <&anyspi_00>,"compatible",
+		      <&anyspi_01>,"compatible",
+		      <&anyspi_10>,"compatible",
+		      <&anyspi_11>,"compatible",
+		      <&anyspi_12>,"compatible",
+		      <&anyspi_20>,"compatible",
+		      <&anyspi_21>,"compatible",
+		      <&anyspi_22>,"compatible";
+		speed = <&anyspi_00>, "spi-max-frequency:0",
+		        <&anyspi_01>, "spi-max-frequency:0",
+		        <&anyspi_10>, "spi-max-frequency:0",
+		        <&anyspi_11>, "spi-max-frequency:0",
+		        <&anyspi_12>, "spi-max-frequency:0",
+		        <&anyspi_20>, "spi-max-frequency:0",
+		        <&anyspi_21>, "spi-max-frequency:0",
+		        <&anyspi_22>, "spi-max-frequency:0";
+	};
+};

arch/arm/boot/dts/overlays/apds9960-overlay.dts

+// Definitions for APDS-9960 ambient light and gesture sensor
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835";
+
+	fragment@0 {
+		target = <&i2c1>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&gpio>;
+		__overlay__ {
+			apds9960_pins: apds9960_pins@39 {
+				brcm,pins = <4>;
+				brcm,function = <0>;
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			apds9960: apds@39 {
+				compatible = "avago,apds9960";
+				reg = <0x39>;
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@3 {
+		target = <&i2c1>;
+		__overlay__ {
+			apds9960_irq: apds@39 {
+				#interrupt-cells=<2>;
+				interrupt-parent = <&gpio>;
+				interrupts = <4 1>;
+			};
+		};
+	};
+
+	__overrides__ {
+		gpiopin = <&apds9960_pins>,"brcm,pins:0",
+				<&apds9960_irq>,"interrupts:0";
+		noints = <0>,"!1!3";
+	};
+};
+

arch/arm/boot/dts/overlays/applepi-dac-overlay.dts

+/dts-v1/;
+/plugin/;
+
+/ {
+    compatible = "brcm,bcm2835";
+
+    fragment@0 {
+        target = <&sound>;
+        __overlay__ {
+            compatible = "simple-audio-card";
+            simple-audio-card,name = "ApplePi-DAC";
+
+            status = "okay";
+
+            playback_link: simple-audio-card,dai-link@1 {
+                format = "i2s";
+
+                p_cpu_dai: cpu {
+                    sound-dai = <&i2s>;
+                    dai-tdm-slot-num = <2>;
+                    dai-tdm-slot-width = <32>;
+                };
+
+                p_codec_dai: codec {
+                    sound-dai = <&codec_out>;
+                };
+            };
+        };
+    };
+
+    fragment@1 {
+        target-path = "/";
+        __overlay__ {
+            codec_out: pcm1794a-codec {
+                #sound-dai-cells = <0>;
+                compatible = "ti,pcm1794a";
+                status = "okay";
+            };
+        };
+    };
+
+    fragment@2 {
+        target = <&i2s>;
+        __overlay__ {
+            #sound-dai-cells = <0>;
+            status = "okay";
+        };
+    };
+};
+
+/*
+   Written by: Leonid Ayzenshtat
+   Company: Orchard Audio (www.orchardaudio.com)
+
+   compile with:
+   dtc -@ -H epapr -O dtb -o ApplePi-DAC.dtbo -W no-unit_address_vs_reg ApplePi-DAC.dts
+*/

arch/arm/boot/dts/overlays/audioinjector-wm8731-audio-overlay.dts

+// Definitions for audioinjector.net audio add on soundcard
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "brcm,bcm2835";
+
+	fragment@0 {
+		target = <&i2s>;
+		__overlay__ {
+			status = "okay";
+		};
+	};
+
+	fragment@1 {
+		target = <&i2c1>;
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			wm8731@1a {
+				#sound-dai-cells = <0>;
+				compatible = "wlf,wm8731";
+				reg = <0x1a>;
+				status = "okay";
+			};
+		};
+	};
+
+	fragment@2 {
+		target = <&sound>;
+		__overlay__ {
+			compatible = "ai,audioinjector-pi-soundcard";
+			i2s-controller = <&i2s>;
+			status = "okay";
+		};
+	};
+};