提交 feed9bab 编写于 作者: K Kalle Valo 提交者: Linus Torvalds

spi: omap2_mcspi PIO RX fix

Before transmission of the last word in PIO RX_ONLY mode rx+tx mode
is enabled:

	/* prevent last RX_ONLY read from triggering
	 * more word i/o: switch to rx+tx
	 */
	if (c == 0 && tx == NULL)
		mcspi_write_cs_reg(spi,
				OMAP2_MCSPI_CHCONF0, l);

But because c is decremented after the test, c will never be zero and
rx+tx will not be enabled. This breaks RX_ONLY mode PIO transfers.

Fix it by decrementing c in the beginning of the various I/O loops.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
上级 dbcc2ec6
......@@ -350,6 +350,7 @@ omap2_mcspi_txrx_pio(struct spi_device *spi, struct spi_transfer *xfer)
tx = xfer->tx_buf;
do {
c -= 1;
if (tx != NULL) {
if (mcspi_wait_for_reg_bit(chstat_reg,
OMAP2_MCSPI_CHSTAT_TXS) < 0) {
......@@ -380,7 +381,6 @@ omap2_mcspi_txrx_pio(struct spi_device *spi, struct spi_transfer *xfer)
word_len, *(rx - 1));
#endif
}
c -= 1;
} while (c);
} else if (word_len <= 16) {
u16 *rx;
......@@ -389,6 +389,7 @@ omap2_mcspi_txrx_pio(struct spi_device *spi, struct spi_transfer *xfer)
rx = xfer->rx_buf;
tx = xfer->tx_buf;
do {
c -= 2;
if (tx != NULL) {
if (mcspi_wait_for_reg_bit(chstat_reg,
OMAP2_MCSPI_CHSTAT_TXS) < 0) {
......@@ -419,7 +420,6 @@ omap2_mcspi_txrx_pio(struct spi_device *spi, struct spi_transfer *xfer)
word_len, *(rx - 1));
#endif
}
c -= 2;
} while (c);
} else if (word_len <= 32) {
u32 *rx;
......@@ -428,6 +428,7 @@ omap2_mcspi_txrx_pio(struct spi_device *spi, struct spi_transfer *xfer)
rx = xfer->rx_buf;
tx = xfer->tx_buf;
do {
c -= 4;
if (tx != NULL) {
if (mcspi_wait_for_reg_bit(chstat_reg,
OMAP2_MCSPI_CHSTAT_TXS) < 0) {
......@@ -458,7 +459,6 @@ omap2_mcspi_txrx_pio(struct spi_device *spi, struct spi_transfer *xfer)
word_len, *(rx - 1));
#endif
}
c -= 4;
} while (c);
}
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册