V4L/DVB (12410): em28xx: Move the non-board dependent part to be outside em28xx_pre_card_setup()

em28xx_pre_card_setup() is meant to contain board-specific initialization. Also,
as autodetection sometimes occur only after having i2c bus enabled, this
function may need to be called later.

Moving those setups to happen outside the function avoids calling it twice without
need and without duplicating output lines at dmesg.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

drivers/media/video/em28xx/em28xx-cards.c

@@ -1821,63 +1821,6 @@ static int em28xx_hint_sensor(struct em28xx *dev)
  */
 void em28xx_pre_card_setup(struct em28xx *dev)
 {
-	int rc;
-
-	em28xx_set_model(dev);
-
-	em28xx_info("Identified as %s (card=%d)\n",
-		    dev->board.name, dev->model);
-
-	/* Set the default GPO/GPIO for legacy devices */
-	dev->reg_gpo_num = EM2880_R04_GPO;
-	dev->reg_gpio_num = EM28XX_R08_GPIO;
-
-	dev->wait_after_write = 5;
-
-	/* Based on the Chip ID, set the device configuration */
-	rc = em28xx_read_reg(dev, EM28XX_R0A_CHIPID);
-	if (rc > 0) {
-		dev->chip_id = rc;
-
-		switch (dev->chip_id) {
-		case CHIP_ID_EM2710:
-			em28xx_info("chip ID is em2710\n");
-			break;
-		case CHIP_ID_EM2750:
-			em28xx_info("chip ID is em2750\n");
-			break;
-		case CHIP_ID_EM2820:
-			em28xx_info("chip ID is em2820 (or em2710)\n");
-			break;
-		case CHIP_ID_EM2840:
-			em28xx_info("chip ID is em2840\n");
-			break;
-		case CHIP_ID_EM2860:
-			em28xx_info("chip ID is em2860\n");
-			break;
-		case CHIP_ID_EM2870:
-			em28xx_info("chip ID is em2870\n");
-			dev->wait_after_write = 0;
-			break;
-		case CHIP_ID_EM2874:
-			em28xx_info("chip ID is em2874\n");
-			dev->reg_gpio_num = EM2874_R80_GPIO;
-			dev->wait_after_write = 0;
-			break;
-		case CHIP_ID_EM2883:
-			em28xx_info("chip ID is em2882/em2883\n");
-			dev->wait_after_write = 0;
-			break;
-		default:
-			em28xx_info("em28xx chip ID = %d\n", dev->chip_id);
-		}
-	}
-
-	/* Prepopulate cached GPO register content */
-	rc = em28xx_read_reg(dev, dev->reg_gpo_num);
-	if (rc >= 0)
-		dev->reg_gpo = rc;
-
 	/* Set the initial XCLK and I2C clock values based on the board
 	   definition */
 	em28xx_write_reg(dev, EM28XX_R0F_XCLK, dev->board.xclk & 0x7f);
@@ -2443,7 +2386,7 @@ static int em28xx_init_dev(struct em28xx **devhandle, struct usb_device *udev,
 			   int minor)
 {
 	struct em28xx *dev = *devhandle;
-	int retval = -ENOMEM;
+	int retval;
 	int errCode;
 
 	dev->udev = udev;
@@ -2460,6 +2403,58 @@ static int em28xx_init_dev(struct em28xx **devhandle, struct usb_device *udev,
 	dev->em28xx_read_reg_req = em28xx_read_reg_req;
 	dev->board.is_em2800 = em28xx_boards[dev->model].is_em2800;
 
+	em28xx_set_model(dev);
+
+	/* Set the default GPO/GPIO for legacy devices */
+	dev->reg_gpo_num = EM2880_R04_GPO;
+	dev->reg_gpio_num = EM28XX_R08_GPIO;
+
+	dev->wait_after_write = 5;
+
+	/* Based on the Chip ID, set the device configuration */
+	retval = em28xx_read_reg(dev, EM28XX_R0A_CHIPID);
+	if (retval > 0) {
+		dev->chip_id = retval;
+
+		switch (dev->chip_id) {
+		case CHIP_ID_EM2710:
+			em28xx_info("chip ID is em2710\n");
+			break;
+		case CHIP_ID_EM2750:
+			em28xx_info("chip ID is em2750\n");
+			break;
+		case CHIP_ID_EM2820:
+			em28xx_info("chip ID is em2820 (or em2710)\n");
+			break;
+		case CHIP_ID_EM2840:
+			em28xx_info("chip ID is em2840\n");
+			break;
+		case CHIP_ID_EM2860:
+			em28xx_info("chip ID is em2860\n");
+			break;
+		case CHIP_ID_EM2870:
+			em28xx_info("chip ID is em2870\n");
+			dev->wait_after_write = 0;
+			break;
+		case CHIP_ID_EM2874:
+			em28xx_info("chip ID is em2874\n");
+			dev->reg_gpio_num = EM2874_R80_GPIO;
+			dev->wait_after_write = 0;
+			break;
+		case CHIP_ID_EM2883:
+			em28xx_info("chip ID is em2882/em2883\n");
+			dev->wait_after_write = 0;
+			break;
+		default:
+			em28xx_info("em28xx chip ID = %d\n", dev->chip_id);
+		}
+	}
+
+	/* Prepopulate cached GPO register content */
+	retval = em28xx_read_reg(dev, dev->reg_gpo_num);
+	if (retval >= 0)
+		dev->reg_gpo = retval;
+
 	em28xx_pre_card_setup(dev);
 
 	if (!dev->board.is_em2800) {