omap3: nand: making ecc layout as compatible with romcode ecc

This patch overrides nand ecc layout and bad block descriptor (for 8-bit
device) to support hw ecc in romcode layout. So as to have in sync with ecc
layout throughout; i.e. x-loader, u-boot and kernel.

This enables to flash x-loader, u-boot, kernel, FS images from kernel itself
and compatiable with other tools.

This patch does not enables this feature by default and need to pass from
board file to enable for any board.
Signed-off-by: NVimal Singh <vimalsingh@ti.com>
Signed-off-by: NSukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

arch/arm/plat-omap/include/plat/gpmc.h

@@ -90,6 +90,8 @@ enum omap_ecc {
 		/* 1-bit ecc: stored at end of spare area */
 	OMAP_ECC_HAMMING_CODE_DEFAULT = 0, /* Default, s/w method */
 	OMAP_ECC_HAMMING_CODE_HW, /* gpmc to detect the error */
+		/* 1-bit ecc: stored at begining of spare area as romcode */
+	OMAP_ECC_HAMMING_CODE_HW_ROMCODE, /* gpmc method & romcode layout */
 };
 
 /*

drivers/mtd/nand/omap2.c

@@ -98,6 +98,20 @@
 static const char *part_probes[] = { "cmdlinepart", NULL };
 #endif
 
+/* oob info generated runtime depending on ecc algorithm and layout selected */
+static struct nand_ecclayout omap_oobinfo;
+/* Define some generic bad / good block scan pattern which are used
+ * while scanning a device for factory marked good / bad blocks
+ */
+static uint8_t scan_ff_pattern[] = { 0xff };
+static struct nand_bbt_descr bb_descrip_flashbased = {
+	.options = NAND_BBT_SCANEMPTY | NAND_BBT_SCANALLPAGES,
+	.offs = 0,
+	.len = 1,
+	.pattern = scan_ff_pattern,
+};
+
+
 struct omap_nand_info {
 	struct nand_hw_control		controller;
 	struct omap_nand_platform_data	*pdata;
@@ -914,6 +928,7 @@ static int __devinit omap_nand_probe(struct platform_device *pdev)
 	struct omap_nand_info		*info;
 	struct omap_nand_platform_data	*pdata;
 	int				err;
+	int				i, offset;
 
 	pdata = pdev->dev.platform_data;
 	if (pdata == NULL) {
@@ -1037,7 +1052,8 @@ static int __devinit omap_nand_probe(struct platform_device *pdev)
 	/* selsect the ecc type */
 	if (pdata->ecc_opt == OMAP_ECC_HAMMING_CODE_DEFAULT)
 		info->nand.ecc.mode = NAND_ECC_SOFT;
-	else if (pdata->ecc_opt == OMAP_ECC_HAMMING_CODE_HW) {
+	else if ((pdata->ecc_opt == OMAP_ECC_HAMMING_CODE_HW) ||
+		(pdata->ecc_opt == OMAP_ECC_HAMMING_CODE_HW_ROMCODE)) {
 		info->nand.ecc.bytes            = 3;
 		info->nand.ecc.size             = 512;
 		info->nand.ecc.calculate        = omap_calculate_ecc;
@@ -1057,6 +1073,25 @@ static int __devinit omap_nand_probe(struct platform_device *pdev)
 		}
 	}
 
+	/* rom code layout */
+	if (pdata->ecc_opt == OMAP_ECC_HAMMING_CODE_HW_ROMCODE) {
+
+		if (info->nand.options & NAND_BUSWIDTH_16)
+			offset = 2;
+		else {
+			offset = 1;
+			info->nand.badblock_pattern = &bb_descrip_flashbased;
+		}
+		omap_oobinfo.eccbytes = 3 * (info->mtd.oobsize/16);
+		for (i = 0; i < omap_oobinfo.eccbytes; i++)
+			omap_oobinfo.eccpos[i] = i+offset;
+
+		omap_oobinfo.oobfree->offset = offset + omap_oobinfo.eccbytes;
+		omap_oobinfo.oobfree->length = info->mtd.oobsize -
+					(offset + omap_oobinfo.eccbytes);
+
+		info->nand.ecc.layout = &omap_oobinfo;
+	}
 
 #ifdef CONFIG_MTD_PARTITIONS
 	err = parse_mtd_partitions(&info->mtd, part_probes, &info->parts, 0);