提交 e8d31c20 编写于 作者: J Jason Wessel 提交者: Ingo Molnar

kgdb: add kgdb internal test suite

This patch adds regression tests for testing the kgdb core and arch
specific implementation.

The kgdb test suite is designed to be built into the kernel and not as
a module because it uses a number of low level kernel and kgdb
primitives which should not be exported externally.

The kgdb test suite is designed as a KGDB I/O module which
simulates the communications that a debugger would have with kgdb.
The tests are broken up in to a line by line and referenced here as
a "get" which is kgdb requesting input and "put" which is kgdb
sending a response.

The kgdb suite can be invoked from the kernel command line
arguments system or executed dynamically at run time.  The test
suite uses the variable "kgdbts" to obtain the information about
which tests to run and to configure the verbosity level.  The
following are the various characters you can use with the kgdbts=
line:

When using the "kgdbts=" you only choose one of the following core
test types:
A = Run all the core tests silently
V1 = Run all the core tests with minimal output
V2 = Run all the core tests in debug mode

You can also specify optional tests:
N## = Go to sleep with interrupts of for ## seconds
      to test the HW NMI watchdog
F## = Break at do_fork for ## iterations
S## = Break at sys_open for ## iterations

NOTE: that the do_fork and sys_open tests are mutually exclusive.

To invoke the kgdb test suite from boot you use a kernel start
argument as follows:
	kgdbts=V1 kgdbwait
Or if you wanted to perform the NMI test for 6 seconds and do_fork
test for 100 forks, you could use:
	kgdbts=V1N6F100 kgdbwait

The test suite can also be invoked at run time with:
echo kgdbts=V1N6F100 > /sys/module/kgdbts/parameters/kgdbts
Or as another example:
echo kgdbts=V2 > /sys/module/kgdbts/parameters/kgdbts

When developing a new kgdb arch specific implementation or
using these tests for the purpose of regression testing,
several invocations are required.

1) Boot with the test suite enabled by using the kernel arguments
      "kgdbts=V1F100 kgdbwait"
   ## If kgdb arch specific implementation has NMI use
      "kgdbts=V1N6F100

2) After the system boot run the basic test.
echo kgdbts=V1 > /sys/module/kgdbts/parameters/kgdbts

3) Run the concurrency tests.  It is best to use n+1
   while loops where n is the number of cpus you have
   in your system.  The example below uses only two
   loops.

## This tests break points on sys_open
while [ 1 ] ; do find / > /dev/null 2>&1 ; done &
while [ 1 ] ; do find / > /dev/null 2>&1 ; done &
echo kgdbts=V1S10000 > /sys/module/kgdbts/parameters/kgdbts
fg # and hit control-c
fg # and hit control-c
## This tests break points on do_fork
while [ 1 ] ; do date > /dev/null ; done &
while [ 1 ] ; do date > /dev/null ; done &
echo kgdbts=V1F1000 > /sys/module/kgdbts/parameters/kgdbts
fg # and hit control-c
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
上级 737a460f
......@@ -22,3 +22,4 @@ obj-$(CONFIG_FUJITSU_LAPTOP) += fujitsu-laptop.o
obj-$(CONFIG_EEPROM_93CX6) += eeprom_93cx6.o
obj-$(CONFIG_INTEL_MENLOW) += intel_menlow.o
obj-$(CONFIG_ENCLOSURE_SERVICES) += enclosure.o
obj-$(CONFIG_KGDB_TESTS) += kgdbts.o
此差异已折叠。
......@@ -25,3 +25,16 @@ config KGDB_SERIAL_CONSOLE
help
Share a serial console with kgdb. Sysrq-g must be used
to break in initially.
config KGDB_TESTS
bool "KGDB: internal test suite"
depends on KGDB
default n
help
This is a kgdb I/O module specifically designed to test
kgdb's internal functions. This kgdb I/O module is
intended to for the development of new kgdb stubs
as well as regression testing the kgdb internals.
See the drivers/misc/kgdbts.c for the details about
the tests. The most basic of this I/O module is to boot
a kernel boot arguments "kgdbwait kgdbts=V1F100"
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册