regulator: stpmic1: Add active discharge support

Add support for active discharge for USB power switches.
Signed-off-by: Npascal paillet <p.paillet@st.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

drivers/regulator/stpmic1_regulator.c

@@ -176,11 +176,19 @@ static const struct regulator_ops stpmic1_vref_ddr_ops = {
 	.disable = regulator_disable_regmap,
 };
 
+static const struct regulator_ops stpmic1_boost_regul_ops = {
+	.is_enabled = regulator_is_enabled_regmap,
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.set_over_current_protection = stpmic1_set_icc,
+};
+
 static const struct regulator_ops stpmic1_switch_regul_ops = {
 	.is_enabled = regulator_is_enabled_regmap,
 	.enable = regulator_enable_regmap,
 	.disable = regulator_disable_regmap,
 	.set_over_current_protection = stpmic1_set_icc,
+	.set_active_discharge = regulator_set_active_discharge_regmap,
 };
 
 #define REG_LDO(ids, base) { \
@@ -281,7 +289,44 @@ static const struct regulator_ops stpmic1_switch_regul_ops = {
 	.supply_name = #base, \
 }
 
-#define REG_SWITCH(ids, base, reg, mask, val) { \
+#define REG_BOOST(ids, base) { \
+	.name = #ids, \
+	.id = STPMIC1_##ids, \
+	.n_voltages = 1, \
+	.ops = &stpmic1_boost_regul_ops, \
+	.type = REGULATOR_VOLTAGE, \
+	.owner = THIS_MODULE, \
+	.min_uV = 0, \
+	.fixed_uV = 5000000, \
+	.enable_reg = BST_SW_CR, \
+	.enable_mask = BOOST_ENABLED, \
+	.enable_val = BOOST_ENABLED, \
+	.disable_val = 0, \
+	.enable_time = PMIC_ENABLE_TIME_US, \
+	.supply_name = #base, \
+}
+
+#define REG_VBUS_OTG(ids, base) { \
+	.name = #ids, \
+	.id = STPMIC1_##ids, \
+	.n_voltages = 1, \
+	.ops = &stpmic1_switch_regul_ops, \
+	.type = REGULATOR_VOLTAGE, \
+	.owner = THIS_MODULE, \
+	.min_uV = 0, \
+	.fixed_uV = 5000000, \
+	.enable_reg = BST_SW_CR, \
+	.enable_mask = USBSW_OTG_SWITCH_ENABLED, \
+	.enable_val = USBSW_OTG_SWITCH_ENABLED, \
+	.disable_val = 0, \
+	.enable_time = PMIC_ENABLE_TIME_US, \
+	.supply_name = #base, \
+	.active_discharge_reg = BST_SW_CR, \
+	.active_discharge_mask = VBUS_OTG_DISCHARGE, \
+	.active_discharge_on = VBUS_OTG_DISCHARGE, \
+}
+
+#define REG_SW_OUT(ids, base) { \
 	.name = #ids, \
 	.id = STPMIC1_##ids, \
 	.n_voltages = 1, \
@@ -290,12 +335,15 @@ static const struct regulator_ops stpmic1_switch_regul_ops = {
 	.owner = THIS_MODULE, \
 	.min_uV = 0, \
 	.fixed_uV = 5000000, \
-	.enable_reg = (reg), \
-	.enable_mask = (mask), \
-	.enable_val = (val), \
+	.enable_reg = BST_SW_CR, \
+	.enable_mask = SWIN_SWOUT_ENABLED, \
+	.enable_val = SWIN_SWOUT_ENABLED, \
 	.disable_val = 0, \
 	.enable_time = PMIC_ENABLE_TIME_US, \
 	.supply_name = #base, \
+	.active_discharge_reg = BST_SW_CR, \
+	.active_discharge_mask = SW_OUT_DISCHARGE, \
+	.active_discharge_on = SW_OUT_DISCHARGE, \
 }
 
 static const struct stpmic1_regulator_cfg stpmic1_regulator_cfgs[] = {
@@ -375,23 +423,17 @@ static const struct stpmic1_regulator_cfg stpmic1_regulator_cfgs[] = {
 		.mask_reset_mask = BIT(6),
 	},
 	[STPMIC1_BOOST] = {
-		.desc = REG_SWITCH(BOOST, boost, BST_SW_CR,
-				   BOOST_ENABLED,
-				   BOOST_ENABLED),
+		.desc = REG_BOOST(BOOST, boost),
 		.icc_reg = BUCKS_ICCTO_CR,
 		.icc_mask = BIT(6),
 	},
 	[STPMIC1_VBUS_OTG] = {
-		.desc = REG_SWITCH(VBUS_OTG, pwr_sw1, BST_SW_CR,
-				   USBSW_OTG_SWITCH_ENABLED,
-				   USBSW_OTG_SWITCH_ENABLED),
+		.desc = REG_VBUS_OTG(VBUS_OTG, pwr_sw1),
 		.icc_reg = BUCKS_ICCTO_CR,
 		.icc_mask = BIT(4),
 	},
 	[STPMIC1_SW_OUT] = {
-		.desc = REG_SWITCH(SW_OUT, pwr_sw2, BST_SW_CR,
-				   SWIN_SWOUT_ENABLED,
-				   SWIN_SWOUT_ENABLED),
+		.desc = REG_SW_OUT(SW_OUT, pwr_sw2),
 		.icc_reg = BUCKS_ICCTO_CR,
 		.icc_mask = BIT(5),
 	},