Skip to content

K
Kernel

openeuler / Kernel
大约 1 年 前同步成功

通知 5
Star 0
Fork 0
K
Kernel

体验新版 GitCode，发现更多精彩内容 >>

提交 e4719d8d 编写于 作者: A Alexandre Belloni 提交者： Nicolas Ferre
浏览文件
操作

Input: atmel_tsadcc: remove driver 

The atmel_tsadcc driver is not used anymore, it has been replaced by at91_adc so
remove it.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
上级 700a28a5
隐藏空白更改
内联 并排
Showing with 0 addition and 377 deletion
MAINTAINERS
浏览文件 @ e4719d8d
......@@ -1617,12 +1617,6 @@ S: Supported
F: drivers/misc/atmel_tclib.c
F: drivers/clocksource/tcb_clksrc.c
ATMEL TSADCC DRIVER
M: Josh Wu <josh.wu@atmel.com>
L: linux-input@vger.kernel.org
S: Supported
F: drivers/input/touchscreen/atmel_tsadcc.c
ATMEL USBA UDC DRIVER
M: Nicolas Ferre <nicolas.ferre@atmel.com>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
......
drivers/input/touchscreen/Kconfig
浏览文件 @ e4719d8d
......@@ -550,18 +550,6 @@ config TOUCHSCREEN_TI_AM335X_TSC
To compile this driver as a module, choose M here: the
module will be called ti_am335x_tsc.
config TOUCHSCREEN_ATMEL_TSADCC
tristate "Atmel Touchscreen Interface"
depends on ARCH_AT91
help
Say Y here if you have a 4-wire touchscreen connected to the
ADC Controller on your Atmel SoC.
If unsure, say N.
To compile this driver as a module, choose M here: the
module will be called atmel_tsadcc.
config TOUCHSCREEN_UCB1400
tristate "Philips UCB1400 touchscreen"
depends on AC97_BUS
......
drivers/input/touchscreen/Makefile
浏览文件 @ e4719d8d
......@@ -13,7 +13,6 @@ obj-$(CONFIG_TOUCHSCREEN_AD7879_I2C) += ad7879-i2c.o
obj-$(CONFIG_TOUCHSCREEN_AD7879_SPI) += ad7879-spi.o
obj-$(CONFIG_TOUCHSCREEN_ADS7846) += ads7846.o
obj-$(CONFIG_TOUCHSCREEN_ATMEL_MXT) += atmel_mxt_ts.o
obj-$(CONFIG_TOUCHSCREEN_ATMEL_TSADCC) += atmel_tsadcc.o
obj-$(CONFIG_TOUCHSCREEN_AUO_PIXCIR) += auo-pixcir-ts.o
obj-$(CONFIG_TOUCHSCREEN_BU21013) += bu21013_ts.o
obj-$(CONFIG_TOUCHSCREEN_CY8CTMG110) += cy8ctmg110_ts.o
......
drivers/input/touchscreen/atmel_tsadcc.c 已删除 100644 → 0
浏览文件 @ 700a28a5
/*
* Atmel Touch Screen Driver
*
* Copyright (c) 2008 ATMEL
* Copyright (c) 2008 Dan Liang
* Copyright (c) 2008 TimeSys Corporation
* Copyright (c) 2008 Justin Waters
*
* Based on touchscreen code from Atmel Corporation.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/err.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/input.h>
#include <linux/slab.h>
#include <linux/interrupt.h>
#include <linux/clk.h>
#include <linux/platform_device.h>
#include <linux/io.h>
#include <linux/platform_data/atmel.h>
#include <mach/cpu.h>
/* Register definitions based on AT91SAM9RL64 preliminary draft datasheet */
#define ATMEL_TSADCC_CR 0x00 /* Control register */
#define ATMEL_TSADCC_SWRST (1 << 0) /* Software Reset*/
#define ATMEL_TSADCC_START (1 << 1) /* Start conversion */
#define ATMEL_TSADCC_MR 0x04 /* Mode register */
#define ATMEL_TSADCC_TSAMOD (3 << 0) /* ADC mode */
#define ATMEL_TSADCC_TSAMOD_ADC_ONLY_MODE (0x0) /* ADC Mode */
#define ATMEL_TSADCC_TSAMOD_TS_ONLY_MODE (0x1) /* Touch Screen Only Mode */
#define ATMEL_TSADCC_LOWRES (1 << 4) /* Resolution selection */
#define ATMEL_TSADCC_SLEEP (1 << 5) /* Sleep mode */
#define ATMEL_TSADCC_PENDET (1 << 6) /* Pen Detect selection */
#define ATMEL_TSADCC_PRES (1 << 7) /* Pressure Measurement Selection */
#define ATMEL_TSADCC_PRESCAL (0x3f << 8) /* Prescalar Rate Selection */
#define ATMEL_TSADCC_EPRESCAL (0xff << 8) /* Prescalar Rate Selection (Extended) */
#define ATMEL_TSADCC_STARTUP (0x7f << 16) /* Start Up time */
#define ATMEL_TSADCC_SHTIM (0xf << 24) /* Sample & Hold time */
#define ATMEL_TSADCC_PENDBC (0xf << 28) /* Pen Detect debouncing time */
#define ATMEL_TSADCC_TRGR 0x08 /* Trigger register */
#define ATMEL_TSADCC_TRGMOD (7 << 0) /* Trigger mode */
#define ATMEL_TSADCC_TRGMOD_NONE (0 << 0)
#define ATMEL_TSADCC_TRGMOD_EXT_RISING (1 << 0)
#define ATMEL_TSADCC_TRGMOD_EXT_FALLING (2 << 0)
#define ATMEL_TSADCC_TRGMOD_EXT_ANY (3 << 0)
#define ATMEL_TSADCC_TRGMOD_PENDET (4 << 0)
#define ATMEL_TSADCC_TRGMOD_PERIOD (5 << 0)
#define ATMEL_TSADCC_TRGMOD_CONTINUOUS (6 << 0)
#define ATMEL_TSADCC_TRGPER (0xffff << 16) /* Trigger period */
#define ATMEL_TSADCC_TSR 0x0C /* Touch Screen register */
#define ATMEL_TSADCC_TSFREQ (0xf << 0) /* TS Frequency in Interleaved mode */
#define ATMEL_TSADCC_TSSHTIM (0xf << 24) /* Sample & Hold time */
#define ATMEL_TSADCC_CHER 0x10 /* Channel Enable register */
#define ATMEL_TSADCC_CHDR 0x14 /* Channel Disable register */
#define ATMEL_TSADCC_CHSR 0x18 /* Channel Status register */
#define ATMEL_TSADCC_CH(n) (1 << (n)) /* Channel number */
#define ATMEL_TSADCC_SR 0x1C /* Status register */
#define ATMEL_TSADCC_EOC(n) (1 << ((n)+0)) /* End of conversion for channel N */
#define ATMEL_TSADCC_OVRE(n) (1 << ((n)+8)) /* Overrun error for channel N */
#define ATMEL_TSADCC_DRDY (1 << 16) /* Data Ready */
#define ATMEL_TSADCC_GOVRE (1 << 17) /* General Overrun Error */
#define ATMEL_TSADCC_ENDRX (1 << 18) /* End of RX Buffer */
#define ATMEL_TSADCC_RXBUFF (1 << 19) /* TX Buffer full */
#define ATMEL_TSADCC_PENCNT (1 << 20) /* Pen contact */
#define ATMEL_TSADCC_NOCNT (1 << 21) /* No contact */
#define ATMEL_TSADCC_LCDR 0x20 /* Last Converted Data register */
#define ATMEL_TSADCC_DATA (0x3ff << 0) /* Channel data */
#define ATMEL_TSADCC_IER 0x24 /* Interrupt Enable register */
#define ATMEL_TSADCC_IDR 0x28 /* Interrupt Disable register */
#define ATMEL_TSADCC_IMR 0x2C /* Interrupt Mask register */
#define ATMEL_TSADCC_CDR0 0x30 /* Channel Data 0 */
#define ATMEL_TSADCC_CDR1 0x34 /* Channel Data 1 */
#define ATMEL_TSADCC_CDR2 0x38 /* Channel Data 2 */
#define ATMEL_TSADCC_CDR3 0x3C /* Channel Data 3 */
#define ATMEL_TSADCC_CDR4 0x40 /* Channel Data 4 */
#define ATMEL_TSADCC_CDR5 0x44 /* Channel Data 5 */
#define ATMEL_TSADCC_XPOS 0x50
#define ATMEL_TSADCC_Z1DAT 0x54
#define ATMEL_TSADCC_Z2DAT 0x58
#define PRESCALER_VAL(x) ((x) >> 8)
#define ADC_DEFAULT_CLOCK 100000
struct atmel_tsadcc {
struct input_dev *input;
char phys[32];
struct clk *clk;
int irq;
unsigned int prev_absx;
unsigned int prev_absy;
unsigned char bufferedmeasure;
};
static void __iomem *tsc_base;
#define atmel_tsadcc_read(reg) __raw_readl(tsc_base + (reg))
#define atmel_tsadcc_write(reg, val) __raw_writel((val), tsc_base + (reg))
static irqreturn_t atmel_tsadcc_interrupt(int irq, void *dev)
{
struct atmel_tsadcc *ts_dev = (struct atmel_tsadcc *)dev;
struct input_dev *input_dev = ts_dev->input;
unsigned int status;
unsigned int reg;
status = atmel_tsadcc_read(ATMEL_TSADCC_SR);
status &= atmel_tsadcc_read(ATMEL_TSADCC_IMR);
if (status & ATMEL_TSADCC_NOCNT) {
/* Contact lost */
reg = atmel_tsadcc_read(ATMEL_TSADCC_MR) | ATMEL_TSADCC_PENDBC;
atmel_tsadcc_write(ATMEL_TSADCC_MR, reg);
atmel_tsadcc_write(ATMEL_TSADCC_TRGR, ATMEL_TSADCC_TRGMOD_NONE);
atmel_tsadcc_write(ATMEL_TSADCC_IDR,
ATMEL_TSADCC_EOC(3) | ATMEL_TSADCC_NOCNT);
atmel_tsadcc_write(ATMEL_TSADCC_IER, ATMEL_TSADCC_PENCNT);
input_report_key(input_dev, BTN_TOUCH, 0);
ts_dev->bufferedmeasure = 0;
input_sync(input_dev);
} else if (status & ATMEL_TSADCC_PENCNT) {
/* Pen detected */
reg = atmel_tsadcc_read(ATMEL_TSADCC_MR);
reg &= ~ATMEL_TSADCC_PENDBC;
atmel_tsadcc_write(ATMEL_TSADCC_IDR, ATMEL_TSADCC_PENCNT);
atmel_tsadcc_write(ATMEL_TSADCC_MR, reg);
atmel_tsadcc_write(ATMEL_TSADCC_IER,
ATMEL_TSADCC_EOC(3) | ATMEL_TSADCC_NOCNT);
atmel_tsadcc_write(ATMEL_TSADCC_TRGR,
ATMEL_TSADCC_TRGMOD_PERIOD | (0x0FFF << 16));
} else if (status & ATMEL_TSADCC_EOC(3)) {
/* Conversion finished */
if (ts_dev->bufferedmeasure) {
/* Last measurement is always discarded, since it can
* be erroneous.
* Always report previous measurement */
input_report_abs(input_dev, ABS_X, ts_dev->prev_absx);
input_report_abs(input_dev, ABS_Y, ts_dev->prev_absy);
input_report_key(input_dev, BTN_TOUCH, 1);
input_sync(input_dev);
} else
ts_dev->bufferedmeasure = 1;
/* Now make new measurement */
ts_dev->prev_absx = atmel_tsadcc_read(ATMEL_TSADCC_CDR3) << 10;
ts_dev->prev_absx /= atmel_tsadcc_read(ATMEL_TSADCC_CDR2);
ts_dev->prev_absy = atmel_tsadcc_read(ATMEL_TSADCC_CDR1) << 10;
ts_dev->prev_absy /= atmel_tsadcc_read(ATMEL_TSADCC_CDR0);
}
return IRQ_HANDLED;
}
/*
* The functions for inserting/removing us as a module.
*/
static int atmel_tsadcc_probe(struct platform_device *pdev)
{
struct atmel_tsadcc *ts_dev;
struct input_dev *input_dev;
struct resource *res;
struct at91_tsadcc_data *pdata = dev_get_platdata(&pdev->dev);
int err;
unsigned int prsc;
unsigned int reg;
if (!pdata)
return -EINVAL;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!res) {
dev_err(&pdev->dev, "no mmio resource defined.\n");
return -ENXIO;
}
/* Allocate memory for device */
ts_dev = kzalloc(sizeof(struct atmel_tsadcc), GFP_KERNEL);
if (!ts_dev) {
dev_err(&pdev->dev, "failed to allocate memory.\n");
return -ENOMEM;
}
platform_set_drvdata(pdev, ts_dev);
input_dev = input_allocate_device();
if (!input_dev) {
dev_err(&pdev->dev, "failed to allocate input device.\n");
err = -EBUSY;
goto err_free_mem;
}
ts_dev->irq = platform_get_irq(pdev, 0);
if (ts_dev->irq < 0) {
dev_err(&pdev->dev, "no irq ID is designated.\n");
err = -ENODEV;
goto err_free_dev;
}
if (!request_mem_region(res->start, resource_size(res),
"atmel tsadcc regs")) {
dev_err(&pdev->dev, "resources is unavailable.\n");
err = -EBUSY;
goto err_free_dev;
}
tsc_base = ioremap(res->start, resource_size(res));
if (!tsc_base) {
dev_err(&pdev->dev, "failed to map registers.\n");
err = -ENOMEM;
goto err_release_mem;
}
err = request_irq(ts_dev->irq, atmel_tsadcc_interrupt, 0,
pdev->dev.driver->name, ts_dev);
if (err) {
dev_err(&pdev->dev, "failed to allocate irq.\n");
goto err_unmap_regs;
}
ts_dev->clk = clk_get(&pdev->dev, "tsc_clk");
if (IS_ERR(ts_dev->clk)) {
dev_err(&pdev->dev, "failed to get ts_clk\n");
err = PTR_ERR(ts_dev->clk);
goto err_free_irq;
}
ts_dev->input = input_dev;
ts_dev->bufferedmeasure = 0;
snprintf(ts_dev->phys, sizeof(ts_dev->phys),
"%s/input0", dev_name(&pdev->dev));
input_dev->name = "atmel touch screen controller";
input_dev->phys = ts_dev->phys;
input_dev->dev.parent = &pdev->dev;
__set_bit(EV_ABS, input_dev->evbit);
input_set_abs_params(input_dev, ABS_X, 0, 0x3FF, 0, 0);
input_set_abs_params(input_dev, ABS_Y, 0, 0x3FF, 0, 0);
input_set_capability(input_dev, EV_KEY, BTN_TOUCH);
/* clk_enable() always returns 0, no need to check it */
clk_enable(ts_dev->clk);
prsc = clk_get_rate(ts_dev->clk);
dev_info(&pdev->dev, "Master clock is set at: %d Hz\n", prsc);
if (!pdata->adc_clock)
pdata->adc_clock = ADC_DEFAULT_CLOCK;
prsc = (prsc / (2 * pdata->adc_clock)) - 1;
/* saturate if this value is too high */
if (cpu_is_at91sam9rl()) {
if (prsc > PRESCALER_VAL(ATMEL_TSADCC_PRESCAL))
prsc = PRESCALER_VAL(ATMEL_TSADCC_PRESCAL);
} else {
if (prsc > PRESCALER_VAL(ATMEL_TSADCC_EPRESCAL))
prsc = PRESCALER_VAL(ATMEL_TSADCC_EPRESCAL);
}
dev_info(&pdev->dev, "Prescaler is set at: %d\n", prsc);
reg = ATMEL_TSADCC_TSAMOD_TS_ONLY_MODE |
((0x00 << 5) & ATMEL_TSADCC_SLEEP) | /* Normal Mode */
((0x01 << 6) & ATMEL_TSADCC_PENDET) | /* Enable Pen Detect */
(prsc << 8) |
((0x26 << 16) & ATMEL_TSADCC_STARTUP) |
((pdata->pendet_debounce << 28) & ATMEL_TSADCC_PENDBC);
atmel_tsadcc_write(ATMEL_TSADCC_CR, ATMEL_TSADCC_SWRST);
atmel_tsadcc_write(ATMEL_TSADCC_MR, reg);
atmel_tsadcc_write(ATMEL_TSADCC_TRGR, ATMEL_TSADCC_TRGMOD_NONE);
atmel_tsadcc_write(ATMEL_TSADCC_TSR,
(pdata->ts_sample_hold_time << 24) & ATMEL_TSADCC_TSSHTIM);
atmel_tsadcc_read(ATMEL_TSADCC_SR);
atmel_tsadcc_write(ATMEL_TSADCC_IER, ATMEL_TSADCC_PENCNT);
/* All went ok, so register to the input system */
err = input_register_device(input_dev);
if (err)
goto err_fail;
return 0;
err_fail:
clk_disable(ts_dev->clk);
clk_put(ts_dev->clk);
err_free_irq:
free_irq(ts_dev->irq, ts_dev);
err_unmap_regs:
iounmap(tsc_base);
err_release_mem:
release_mem_region(res->start, resource_size(res));
err_free_dev:
input_free_device(input_dev);
err_free_mem:
kfree(ts_dev);
return err;
}
static int atmel_tsadcc_remove(struct platform_device *pdev)
{
struct atmel_tsadcc *ts_dev = platform_get_drvdata(pdev);
struct resource *res;
free_irq(ts_dev->irq, ts_dev);
input_unregister_device(ts_dev->input);
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
iounmap(tsc_base);
release_mem_region(res->start, resource_size(res));
clk_disable(ts_dev->clk);
clk_put(ts_dev->clk);
kfree(ts_dev);
return 0;
}
static struct platform_driver atmel_tsadcc_driver = {
.probe = atmel_tsadcc_probe,
.remove = atmel_tsadcc_remove,
.driver = {
.name = "atmel_tsadcc",
},
};
module_platform_driver(atmel_tsadcc_driver);
MODULE_LICENSE("GPL");
MODULE_DESCRIPTION("Atmel TouchScreen Driver");
MODULE_AUTHOR("Dan Liang <dan.liang@atmel.com>");
Markdown is supported
0% 或 .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑！
想要评论请 注册 或