提交 e3a700d8 编写于 作者: M Milo(Woogyom) Kim 提交者: Bryan Wu

leds-lp55xx: use lp55xx common init function - detect

 LP5521/5523 chip detection functions are replaced with lp55xx common function,
 lp55xx_detect_device().
 Chip dependent address and values are configurable in each driver.
 In init function, chip detection is executed.
Signed-off-by: NMilo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: NBryan Wu <cooloney@gmail.com>
上级 48068d5d
......@@ -328,26 +328,6 @@ static void lp5521_led_brightness_work(struct work_struct *work)
mutex_unlock(&chip->lock);
}
/* Detect the chip by setting its ENABLE register and reading it back. */
static int lp5521_detect(struct i2c_client *client)
{
int ret;
u8 buf;
ret = lp5521_write(client, LP5521_REG_ENABLE, LP5521_ENABLE_DEFAULT);
if (ret)
return ret;
/* enable takes 500us. 1 - 2 ms leaves some margin */
usleep_range(1000, 2000);
ret = lp5521_read(client, LP5521_REG_ENABLE, &buf);
if (ret)
return ret;
if (buf != LP5521_ENABLE_DEFAULT)
return -ENODEV;
return 0;
}
/* Set engine mode and create appropriate sysfs attributes, if required. */
static int lp5521_set_mode(struct lp5521_engine *engine, u8 mode)
{
......@@ -718,12 +698,6 @@ static int lp5521_init_device(struct lp5521_chip *chip)
struct i2c_client *client = chip->client;
int ret;
ret = lp5521_detect(client);
if (ret) {
dev_err(&client->dev, "Chip not found\n");
goto err;
}
ret = lp5521_configure(client);
if (ret < 0) {
dev_err(&client->dev, "error configuring chip\n");
......@@ -734,7 +708,6 @@ static int lp5521_init_device(struct lp5521_chip *chip)
err_config:
lp5521_deinit_device(chip);
err:
return ret;
}
......@@ -851,6 +824,10 @@ static struct lp55xx_device_config lp5521_cfg = {
.addr = LP5521_REG_RESET,
.val = LP5521_RESET,
},
.enable = {
.addr = LP5521_REG_ENABLE,
.val = LP5521_ENABLE_DEFAULT,
},
};
static int lp5521_probe(struct i2c_client *client,
......
......@@ -181,23 +181,6 @@ static int lp5523_read(struct i2c_client *client, u8 reg, u8 *buf)
return 0;
}
static int lp5523_detect(struct i2c_client *client)
{
int ret;
u8 buf;
ret = lp5523_write(client, LP5523_REG_ENABLE, LP5523_ENABLE);
if (ret)
return ret;
ret = lp5523_read(client, LP5523_REG_ENABLE, &buf);
if (ret)
return ret;
if (buf == 0x40)
return 0;
else
return -ENODEV;
}
static int lp5523_configure(struct i2c_client *client)
{
int ret = 0;
......@@ -907,10 +890,6 @@ static int lp5523_init_device(struct lp5523_chip *chip)
struct i2c_client *client = chip->client;
int ret;
ret = lp5523_detect(client);
if (ret)
goto err;
ret = lp5523_configure(client);
if (ret < 0) {
dev_err(&client->dev, "error configuring chip\n");
......@@ -921,7 +900,6 @@ static int lp5523_init_device(struct lp5523_chip *chip)
err_config:
lp5523_deinit_device(chip);
err:
return ret;
}
......@@ -941,6 +919,10 @@ static struct lp55xx_device_config lp5523_cfg = {
.addr = LP5523_REG_RESET,
.val = LP5523_RESET,
},
.enable = {
.addr = LP5523_REG_ENABLE,
.val = LP5523_ENABLE,
},
};
static int lp5523_probe(struct i2c_client *client,
......
......@@ -30,6 +30,29 @@ static void lp55xx_reset_device(struct lp55xx_chip *chip)
lp55xx_write(chip, addr, val);
}
static int lp55xx_detect_device(struct lp55xx_chip *chip)
{
struct lp55xx_device_config *cfg = chip->cfg;
u8 addr = cfg->enable.addr;
u8 val = cfg->enable.val;
int ret;
ret = lp55xx_write(chip, addr, val);
if (ret)
return ret;
usleep_range(1000, 2000);
ret = lp55xx_read(chip, addr, &val);
if (ret)
return ret;
if (val != cfg->enable.val)
return -ENODEV;
return 0;
}
int lp55xx_write(struct lp55xx_chip *chip, u8 reg, u8 val)
{
return i2c_smbus_write_byte_data(chip->cl, reg, val);
......@@ -103,6 +126,12 @@ int lp55xx_init_device(struct lp55xx_chip *chip)
*/
usleep_range(10000, 20000);
ret = lp55xx_detect_device(chip);
if (ret) {
dev_err(dev, "device detection err: %d\n", ret);
goto err;
}
err:
return ret;
}
......
......@@ -31,9 +31,11 @@ struct lp55xx_reg {
/*
* struct lp55xx_device_config
* @reset : Chip specific reset command
* @enable : Chip specific enable command
*/
struct lp55xx_device_config {
const struct lp55xx_reg reset;
const struct lp55xx_reg enable;
};
/*
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册