Input: add driver for ADXL345/346 Digital Accelerometers

This is a driver for the ADXL345/346 Three-Axis Digital Accelerometers.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NChris Verges <chrisv@cyberswitching.com>
Signed-off-by: NLuotao Fu <l.fu@pengutronix.de>
Signed-off-by: NBarry Song <barry.song@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

drivers/input/misc/Kconfig

@@ -390,4 +390,41 @@ config INPUT_PCAP
 	  To compile this driver as a module, choose M here: the
 	  module will be called pcap_keys.
 
+config INPUT_ADXL34X
+	tristate "Analog Devices ADXL34x Three-Axis Digital Accelerometer"
+	default n
+	help
+	  Say Y here if you have a Accelerometer interface using the
+	  ADXL345/6 controller, and your board-specific initialization
+	  code includes that in its table of devices.
+
+	  This driver can use either I2C or SPI communication to the
+	  ADXL345/6 controller.  Select the appropriate method for
+	  your system.
+
+	  If unsure, say N (but it's safe to say "Y").
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called adxl34x.
+
+config INPUT_ADXL34X_I2C
+	tristate "support I2C bus connection"
+	depends on INPUT_ADXL34X && I2C
+	default y
+	help
+	  Say Y here if you have ADXL345/6 hooked to an I2C bus.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called adxl34x-i2c.
+
+config INPUT_ADXL34X_SPI
+	tristate "support SPI bus connection"
+	depends on INPUT_ADXL34X && SPI
+	default y
+	help
+	  Say Y here if you have ADXL345/6 hooked to a SPI bus.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called adxl34x-spi.
+
 endif

drivers/input/misc/Makefile

@@ -8,6 +8,9 @@ obj-$(CONFIG_INPUT_88PM860X_ONKEY)	+= 88pm860x_onkey.o
 obj-$(CONFIG_INPUT_AD714X)		+= ad714x.o
 obj-$(CONFIG_INPUT_AD714X_I2C)		+= ad714x-i2c.o
 obj-$(CONFIG_INPUT_AD714X_SPI)		+= ad714x-spi.o
+obj-$(CONFIG_INPUT_ADXL34X)		+= adxl34x.o
+obj-$(CONFIG_INPUT_ADXL34X_I2C)		+= adxl34x-i2c.o
+obj-$(CONFIG_INPUT_ADXL34X_SPI)		+= adxl34x-spi.o
 obj-$(CONFIG_INPUT_APANEL)		+= apanel.o
 obj-$(CONFIG_INPUT_ATI_REMOTE)		+= ati_remote.o
 obj-$(CONFIG_INPUT_ATI_REMOTE2)		+= ati_remote2.o

drivers/input/misc/adxl34x-i2c.c

+/*
+ * ADLX345/346 Three-Axis Digital Accelerometers (I2C Interface)
+ *
+ * Enter bugs at http://blackfin.uclinux.org/
+ *
+ * Copyright (C) 2009 Michael Hennerich, Analog Devices Inc.
+ * Licensed under the GPL-2 or later.
+ */
+
+#include <linux/input.h>	/* BUS_I2C */
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include "adxl34x.h"
+
+static int adxl34x_smbus_read(struct device *dev, unsigned char reg)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+
+	return i2c_smbus_read_byte_data(client, reg);
+}
+
+static int adxl34x_smbus_write(struct device *dev,
+			       unsigned char reg, unsigned char val)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+
+	return i2c_smbus_write_byte_data(client, reg, val);
+}
+
+static int adxl34x_smbus_read_block(struct device *dev,
+				    unsigned char reg, int count,
+				    void *buf)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+
+	return i2c_smbus_read_i2c_block_data(client, reg, count, buf);
+}
+
+static int adxl34x_i2c_read_block(struct device *dev,
+				  unsigned char reg, int count,
+				  void *buf)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	int ret;
+
+	ret = i2c_master_send(client, &reg, 1);
+	if (ret < 0)
+		return ret;
+
+	ret = i2c_master_recv(client, buf, count);
+	if (ret < 0)
+		return ret;
+
+	if (ret != count)
+		return -EIO;
+
+	return 0;
+}
+
+static const struct adxl34x_bus_ops adx134x_smbus_bops = {
+	.bustype	= BUS_I2C,
+	.write		= adxl34x_smbus_write,
+	.read		= adxl34x_smbus_read,
+	.read_block	= adxl34x_smbus_read_block,
+};
+
+static const struct adxl34x_bus_ops adx134x_i2c_bops = {
+	.bustype	= BUS_I2C,
+	.write		= adxl34x_smbus_write,
+	.read		= adxl34x_smbus_read,
+	.read_block	= adxl34x_i2c_read_block,
+};
+
+static int __devinit adxl34x_i2c_probe(struct i2c_client *client,
+				       const struct i2c_device_id *id)
+{
+	struct adxl34x *ac;
+	int error;
+
+	error = i2c_check_functionality(client->adapter,
+			I2C_FUNC_SMBUS_BYTE_DATA);
+	if (!error) {
+		dev_err(&client->dev, "SMBUS Byte Data not Supported\n");
+		return -EIO;
+	}
+
+	ac = adxl34x_probe(&client->dev, client->irq, false,
+			   i2c_check_functionality(client->adapter,
+						   I2C_FUNC_SMBUS_READ_I2C_BLOCK) ?
+				&adx134x_smbus_bops : &adx134x_i2c_bops);
+	if (IS_ERR(ac))
+		return PTR_ERR(ac);
+
+	i2c_set_clientdata(client, ac);
+
+	return 0;
+}
+
+static int __devexit adxl34x_i2c_remove(struct i2c_client *client)
+{
+	struct adxl34x *ac = i2c_get_clientdata(client);
+
+	return adxl34x_remove(ac);
+}
+
+#ifdef CONFIG_PM
+static int adxl34x_suspend(struct i2c_client *client, pm_message_t message)
+{
+	struct adxl34x *ac = i2c_get_clientdata(client);
+
+	adxl34x_disable(ac);
+
+	return 0;
+}
+
+static int adxl34x_resume(struct i2c_client *client)
+{
+	struct adxl34x *ac = i2c_get_clientdata(client);
+
+	adxl34x_enable(ac);
+
+	return 0;
+}
+#else
+# define adxl34x_suspend NULL
+# define adxl34x_resume  NULL
+#endif
+
+static const struct i2c_device_id adxl34x_id[] = {
+	{ "adxl34x", 0 },
+	{ }
+};
+
+MODULE_DEVICE_TABLE(i2c, adxl34x_id);
+
+static struct i2c_driver adxl34x_driver = {
+	.driver = {
+		.name = "adxl34x",
+		.owner = THIS_MODULE,
+	},
+	.probe    = adxl34x_i2c_probe,
+	.remove   = __devexit_p(adxl34x_i2c_remove),
+	.suspend  = adxl34x_suspend,
+	.resume   = adxl34x_resume,
+	.id_table = adxl34x_id,
+};
+
+static int __init adxl34x_i2c_init(void)
+{
+	return i2c_add_driver(&adxl34x_driver);
+}
+module_init(adxl34x_i2c_init);
+
+static void __exit adxl34x_i2c_exit(void)
+{
+	i2c_del_driver(&adxl34x_driver);
+}
+module_exit(adxl34x_i2c_exit);
+
+MODULE_AUTHOR("Michael Hennerich <hennerich@blackfin.uclinux.org>");
+MODULE_DESCRIPTION("ADXL345/346 Three-Axis Digital Accelerometer I2C Bus Driver");
+MODULE_LICENSE("GPL");

drivers/input/misc/adxl34x-spi.c

+/*
+ * ADLX345/346 Three-Axis Digital Accelerometers (SPI Interface)
+ *
+ * Enter bugs at http://blackfin.uclinux.org/
+ *
+ * Copyright (C) 2009 Michael Hennerich, Analog Devices Inc.
+ * Licensed under the GPL-2 or later.
+ */
+
+#include <linux/input.h>	/* BUS_SPI */
+#include <linux/module.h>
+#include <linux/spi/spi.h>
+#include <linux/types.h>
+#include "adxl34x.h"
+
+#define MAX_SPI_FREQ_HZ		5000000
+#define MAX_FREQ_NO_FIFODELAY	1500000
+#define ADXL34X_CMD_MULTB	(1 << 6)
+#define ADXL34X_CMD_READ	(1 << 7)
+#define ADXL34X_WRITECMD(reg)	(reg & 0x3F)
+#define ADXL34X_READCMD(reg)	(ADXL34X_CMD_READ | (reg & 0x3F))
+#define ADXL34X_READMB_CMD(reg) (ADXL34X_CMD_READ | ADXL34X_CMD_MULTB \
+					| (reg & 0x3F))
+
+static int adxl34x_spi_read(struct device *dev, unsigned char reg)
+{
+	struct spi_device *spi = to_spi_device(dev);
+	unsigned char cmd;
+
+	cmd = ADXL34X_READCMD(reg);
+
+	return spi_w8r8(spi, cmd);
+}
+
+static int adxl34x_spi_write(struct device *dev,
+			     unsigned char reg, unsigned char val)
+{
+	struct spi_device *spi = to_spi_device(dev);
+	unsigned char buf[2];
+
+	buf[0] = ADXL34X_WRITECMD(reg);
+	buf[1] = val;
+
+	return spi_write(spi, buf, sizeof(buf));
+}
+
+static int adxl34x_spi_read_block(struct device *dev,
+				  unsigned char reg, int count,
+				  void *buf)
+{
+	struct spi_device *spi = to_spi_device(dev);
+	ssize_t status;
+
+	reg = ADXL34X_READMB_CMD(reg);
+	status = spi_write_then_read(spi, &reg, 1, buf, count);
+
+	return (status < 0) ? status : 0;
+}
+
+static const struct adxl34x_bus_ops adx134x_spi_bops = {
+	.bustype	= BUS_SPI,
+	.write		= adxl34x_spi_write,
+	.read		= adxl34x_spi_read,
+	.read_block	= adxl34x_spi_read_block,
+};
+
+static int __devinit adxl34x_spi_probe(struct spi_device *spi)
+{
+	struct adxl34x *ac;
+
+	/* don't exceed max specified SPI CLK frequency */
+	if (spi->max_speed_hz > MAX_SPI_FREQ_HZ) {
+		dev_err(&spi->dev, "SPI CLK %d Hz too fast\n", spi->max_speed_hz);
+		return -EINVAL;
+	}
+
+	ac = adxl34x_probe(&spi->dev, spi->irq,
+			   spi->max_speed_hz > MAX_FREQ_NO_FIFODELAY,
+			   &adx134x_spi_bops);
+
+	if (IS_ERR(ac))
+		return PTR_ERR(ac);
+
+	spi_set_drvdata(spi, ac);
+
+	return 0;
+}
+
+static int __devexit adxl34x_spi_remove(struct spi_device *spi)
+{
+	struct adxl34x *ac = dev_get_drvdata(&spi->dev);
+
+	return adxl34x_remove(ac);
+}
+
+#ifdef CONFIG_PM
+static int adxl34x_suspend(struct spi_device *spi, pm_message_t message)
+{
+	struct adxl34x *ac = dev_get_drvdata(&spi->dev);
+
+	adxl34x_disable(ac);
+
+	return 0;
+}
+
+static int adxl34x_resume(struct spi_device *spi)
+{
+	struct adxl34x *ac = dev_get_drvdata(&spi->dev);
+
+	adxl34x_enable(ac);
+
+	return 0;
+}
+#else
+# define adxl34x_suspend NULL
+# define adxl34x_resume  NULL
+#endif
+
+static struct spi_driver adxl34x_driver = {
+	.driver = {
+		.name = "adxl34x",
+		.bus = &spi_bus_type,
+		.owner = THIS_MODULE,
+	},
+	.probe   = adxl34x_spi_probe,
+	.remove  = __devexit_p(adxl34x_spi_remove),
+	.suspend = adxl34x_suspend,
+	.resume  = adxl34x_resume,
+};
+
+static int __init adxl34x_spi_init(void)
+{
+	return spi_register_driver(&adxl34x_driver);
+}
+module_init(adxl34x_spi_init);
+
+static void __exit adxl34x_spi_exit(void)
+{
+	spi_unregister_driver(&adxl34x_driver);
+}
+module_exit(adxl34x_spi_exit);
+
+MODULE_AUTHOR("Michael Hennerich <hennerich@blackfin.uclinux.org>");
+MODULE_DESCRIPTION("ADXL345/346 Three-Axis Digital Accelerometer SPI Bus Driver");
+MODULE_LICENSE("GPL");

drivers/input/misc/adxl34x.h

+/*
+ * ADXL345/346 Three-Axis Digital Accelerometers (I2C/SPI Interface)
+ *
+ * Enter bugs at http://blackfin.uclinux.org/
+ *
+ * Copyright (C) 2009 Michael Hennerich, Analog Devices Inc.
+ * Licensed under the GPL-2 or later.
+ */
+
+#ifndef _ADXL34X_H_
+#define _ADXL34X_H_
+
+struct device;
+struct adxl34x;
+
+struct adxl34x_bus_ops {
+	u16 bustype;
+	int (*read)(struct device *, unsigned char);
+	int (*read_block)(struct device *, unsigned char, int, void *);
+	int (*write)(struct device *, unsigned char, unsigned char);
+};
+
+void adxl34x_disable(struct adxl34x *ac);
+void adxl34x_enable(struct adxl34x *ac);
+struct adxl34x *adxl34x_probe(struct device *dev, int irq,
+			      bool fifo_delay_default,
+			      const struct adxl34x_bus_ops *bops);
+int adxl34x_remove(struct adxl34x *ac);
+
+#endif

include/linux/input/adxl34x.h

+/*
+ * include/linux/input/adxl34x.h
+ *
+ * Digital Accelerometer characteristics are highly application specific
+ * and may vary between boards and models. The platform_data for the
+ * device's "struct device" holds this information.
+ *
+ * Copyright 2009 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#ifndef __LINUX_INPUT_ADXL34X_H__
+#define __LINUX_INPUT_ADXL34X_H__
+
+struct adxl34x_platform_data {
+
+	/*
+	 * X,Y,Z Axis Offset:
+	 * offer user offset adjustments in twoscompliment
+	 * form with a scale factor of 15.6 mg/LSB (i.e. 0x7F = +2 g)
+	 */
+
+	s8 x_axis_offset;
+	s8 y_axis_offset;
+	s8 z_axis_offset;
+
+	/*
+	 * TAP_X/Y/Z Enable: Setting TAP_X, Y, or Z Enable enables X,
+	 * Y, or Z participation in Tap detection. A '0' excludes the
+	 * selected axis from participation in Tap detection.
+	 * Setting the SUPPRESS bit suppresses Double Tap detection if
+	 * acceleration greater than tap_threshold is present between
+	 * taps.
+	 */
+
+#define ADXL_SUPPRESS	(1 << 3)
+#define ADXL_TAP_X_EN	(1 << 2)
+#define ADXL_TAP_Y_EN	(1 << 1)
+#define ADXL_TAP_Z_EN	(1 << 0)
+
+	u8 tap_axis_control;
+
+	/*
+	 * tap_threshold:
+	 * holds the threshold value for tap detection/interrupts.
+	 * The data format is unsigned. The scale factor is 62.5 mg/LSB
+	 * (i.e. 0xFF = +16 g). A zero value may result in undesirable
+	 * behavior if Tap/Double Tap is enabled.
+	 */
+
+	u8 tap_threshold;
+
+	/*
+	 * tap_duration:
+	 * is an unsigned time value representing the maximum
+	 * time that an event must be above the tap_threshold threshold
+	 * to qualify as a tap event. The scale factor is 625 us/LSB. A zero
+	 * value will prevent Tap/Double Tap functions from working.
+	 */
+
+	u8 tap_duration;
+
+	/*
+	 * tap_latency:
+	 * is an unsigned time value representing the wait time
+	 * from the detection of a tap event to the opening of the time
+	 * window tap_window for a possible second tap event. The scale
+	 * factor is 1.25 ms/LSB. A zero value will disable the Double Tap
+	 * function.
+	 */
+
+	u8 tap_latency;
+
+	/*
+	 * tap_window:
+	 * is an unsigned time value representing the amount
+	 * of time after the expiration of tap_latency during which a second
+	 * tap can begin. The scale factor is 1.25 ms/LSB. A zero value will
+	 * disable the Double Tap function.
+	 */
+
+	u8 tap_window;
+
+	/*
+	 * act_axis_control:
+	 * X/Y/Z Enable: A '1' enables X, Y, or Z participation in activity
+	 * or inactivity detection. A '0' excludes the selected axis from
+	 * participation. If all of the axes are excluded, the function is
+	 * disabled.
+	 * AC/DC: A '0' = DC coupled operation and a '1' = AC coupled
+	 * operation. In DC coupled operation, the current acceleration is
+	 * compared with activity_threshold and inactivity_threshold directly
+	 * to determine whether activity or inactivity is detected. In AC
+	 * coupled operation for activity detection, the acceleration value
+	 * at the start of activity detection is taken as a reference value.
+	 * New samples of acceleration are then compared to this
+	 * reference value and if the magnitude of the difference exceeds
+	 * activity_threshold the device will trigger an activity interrupt. In
+	 * AC coupled operation for inactivity detection, a reference value
+	 * is used again for comparison and is updated whenever the
+	 * device exceeds the inactivity threshold. Once the reference
+	 * value is selected, the device compares the magnitude of the
+	 * difference between the reference value and the current
+	 * acceleration with inactivity_threshold. If the difference is below
+	 * inactivity_threshold for a total of inactivity_time, the device is
+	 * considered inactive and the inactivity interrupt is triggered.
+	 */
+
+#define ADXL_ACT_ACDC		(1 << 7)
+#define ADXL_ACT_X_EN		(1 << 6)
+#define ADXL_ACT_Y_EN		(1 << 5)
+#define ADXL_ACT_Z_EN		(1 << 4)
+#define ADXL_INACT_ACDC		(1 << 3)
+#define ADXL_INACT_X_EN		(1 << 2)
+#define ADXL_INACT_Y_EN		(1 << 1)
+#define ADXL_INACT_Z_EN		(1 << 0)
+
+	u8 act_axis_control;
+
+	/*
+	 * activity_threshold:
+	 * holds the threshold value for activity detection.
+	 * The data format is unsigned. The scale factor is
+	 * 62.5 mg/LSB. A zero value may result in undesirable behavior if
+	 * Activity interrupt is enabled.
+	 */
+
+	u8 activity_threshold;
+
+	/*
+	 * inactivity_threshold:
+	 * holds the threshold value for inactivity
+	 * detection. The data format is unsigned. The scale
+	 * factor is 62.5 mg/LSB. A zero value may result in undesirable
+	 * behavior if Inactivity interrupt is enabled.
+	 */
+
+	u8 inactivity_threshold;
+
+	/*
+	 * inactivity_time:
+	 * is an unsigned time value representing the
+	 * amount of time that acceleration must be below the value in
+	 * inactivity_threshold for inactivity to be declared. The scale factor
+	 * is 1 second/LSB. Unlike the other interrupt functions, which
+	 * operate on unfiltered data, the inactivity function operates on the
+	 * filtered output data. At least one output sample must be
+	 * generated for the inactivity interrupt to be triggered. This will
+	 * result in the function appearing un-responsive if the
+	 * inactivity_time register is set with a value less than the time
+	 * constant of the Output Data Rate. A zero value will result in an
+	 * interrupt when the output data is below inactivity_threshold.
+	 */
+
+	u8 inactivity_time;
+
+	/*
+	 * free_fall_threshold:
+	 * holds the threshold value for Free-Fall detection.
+	 * The data format is unsigned. The root-sum-square(RSS) value
+	 * of all axes is calculated and compared to the value in
+	 * free_fall_threshold to determine if a free fall event may be
+	 * occurring.  The scale factor is 62.5 mg/LSB. A zero value may
+	 * result in undesirable behavior if Free-Fall interrupt is
+	 * enabled. Values between 300 and 600 mg (0x05 to 0x09) are
+	 * recommended.
+	 */
+
+	u8 free_fall_threshold;
+
+	/*
+	 * free_fall_time:
+	 * is an unsigned time value representing the minimum
+	 * time that the RSS value of all axes must be less than
+	 * free_fall_threshold to generate a Free-Fall interrupt. The
+	 * scale factor is 5 ms/LSB. A zero value may result in
+	 * undesirable behavior if Free-Fall interrupt is enabled.
+	 * Values between 100 to 350 ms (0x14 to 0x46) are recommended.
+	 */
+
+	u8 free_fall_time;
+
+	/*
+	 * data_rate:
+	 * Selects device bandwidth and output data rate.
+	 * RATE = 3200 Hz / (2^(15 - x)). Default value is 0x0A, or 100 Hz
+	 * Output Data Rate. An Output Data Rate should be selected that
+	 * is appropriate for the communication protocol and frequency
+	 * selected. Selecting too high of an Output Data Rate with a low
+	 * communication speed will result in samples being discarded.
+	 */
+
+	u8 data_rate;
+
+	/*
+	 * data_range:
+	 * FULL_RES: When this bit is set with the device is
+	 * in Full-Resolution Mode, where the output resolution increases
+	 * with RANGE to maintain a 4 mg/LSB scale factor. When this
+	 * bit is cleared the device is in 10-bit Mode and RANGE determine the
+	 * maximum g-Range and scale factor.
+	 */
+
+#define ADXL_FULL_RES		(1 << 3)
+#define ADXL_RANGE_PM_2g	0
+#define ADXL_RANGE_PM_4g	1
+#define ADXL_RANGE_PM_8g	2
+#define ADXL_RANGE_PM_16g	3
+
+	u8 data_range;
+
+	/*
+	 * low_power_mode:
+	 * A '0' = Normal operation and a '1' = Reduced
+	 * power operation with somewhat higher noise.
+	 */
+
+	u8 low_power_mode;
+
+	/*
+	 * power_mode:
+	 * LINK: A '1' with both the activity and inactivity functions
+	 * enabled will delay the start of the activity function until
+	 * inactivity is detected. Once activity is detected, inactivity
+	 * detection will begin and prevent the detection of activity. This
+	 * bit serially links the activity and inactivity functions. When '0'
+	 * the inactivity and activity functions are concurrent. Additional
+	 * information can be found in the Application section under Link
+	 * Mode.
+	 * AUTO_SLEEP: A '1' sets the ADXL34x to switch to Sleep Mode
+	 * when inactivity (acceleration has been below inactivity_threshold
+	 * for at least inactivity_time) is detected and the LINK bit is set.
+	 * A '0' disables automatic switching to Sleep Mode. See SLEEP
+	 * for further description.
+	 */
+
+#define ADXL_LINK	(1 << 5)
+#define ADXL_AUTO_SLEEP	(1 << 4)
+
+	u8 power_mode;
+
+	/*
+	 * fifo_mode:
+	 * BYPASS The FIFO is bypassed
+	 * FIFO   FIFO collects up to 32 values then stops collecting data
+	 * STREAM FIFO holds the last 32 data values. Once full, the FIFO's
+	 *        oldest data is lost as it is replaced with newer data
+	 *
+	 * DEFAULT should be ADXL_FIFO_STREAM
+	 */
+
+#define ADXL_FIFO_BYPASS	0
+#define ADXL_FIFO_FIFO		1
+#define ADXL_FIFO_STREAM	2
+
+	u8 fifo_mode;
+
+	/*
+	 * watermark:
+	 * The Watermark feature can be used to reduce the interrupt load
+	 * of the system. The FIFO fills up to the value stored in watermark
+	 * [1..32] and then generates an interrupt.
+	 * A '0' disables the watermark feature.
+	 */
+
+	u8 watermark;
+
+	u32 ev_type;	/* EV_ABS or EV_REL */
+
+	u32 ev_code_x;	/* ABS_X,Y,Z or REL_X,Y,Z */
+	u32 ev_code_y;	/* ABS_X,Y,Z or REL_X,Y,Z */
+	u32 ev_code_z;	/* ABS_X,Y,Z or REL_X,Y,Z */
+
+	/*
+	 * A valid BTN or KEY Code; use tap_axis_control to disable
+	 * event reporting
+	 */
+
+	u32 ev_code_tap[3];	/* EV_KEY {X-Axis, Y-Axis, Z-Axis} */
+
+	/*
+	 * A valid BTN or KEY Code for Free-Fall or Activity enables
+	 * input event reporting. A '0' disables the Free-Fall or
+	 * Activity reporting.
+	 */
+
+	u32 ev_code_ff;	/* EV_KEY */
+	u32 ev_code_act_inactivity;	/* EV_KEY */
+
+	u8 use_int2;
+};
+#endif