dm9000: Move the Davicom driver

Move the Davicom driver into drivers/net/ethernet/davicom/ and
make the necessary Kconfig and Makefile changes.

CC: Ben Dooks <ben@simtec.co.uk>
CC: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>

drivers/net/Kconfig

@@ -246,34 +246,6 @@ config NET_NETX
 	  To compile this driver as a module, choose M here. The module
 	  will be called netx-eth.
 
-config DM9000
-	tristate "DM9000 support"
-	depends on ARM || BLACKFIN || MIPS
-	select CRC32
-	select MII
-	---help---
-	  Support for DM9000 chipset.
-
-	  To compile this driver as a module, choose M here.  The module
-	  will be called dm9000.
-
-config DM9000_DEBUGLEVEL
-	int "DM9000 maximum debug level"
-	depends on DM9000
-	default 4
-	help
-	  The maximum level of debugging code compiled into the DM9000
-	  driver.
-
-config DM9000_FORCE_SIMPLE_PHY_POLL
-	bool "Force simple NSR based PHY polling"
-	depends on DM9000
-	---help---
-	  This configuration forces the DM9000 to use the NSR's LinkStatus
-	  bit to determine if the link is up or down instead of the more
-	  costly MII PHY reads. Note, this will not work if the chip is
-	  operating with an external PHY.
-
 config NET_PCI
 	bool "EISA, VLB, PCI and on board controllers"
 	depends on ISA || EISA || PCI

drivers/net/Makefile

@@ -52,7 +52,6 @@ obj-$(CONFIG_EQUALIZER) += eql.o
 obj-$(CONFIG_TUN) += tun.o
 obj-$(CONFIG_VETH) += veth.o
 obj-$(CONFIG_NET_NETX) += netx-eth.o
-obj-$(CONFIG_DM9000) += dm9000.o
 
 obj-$(CONFIG_DEV_APPLETALK) += appletalk/
 obj-$(CONFIG_ETHERNET) += ethernet/

drivers/net/ethernet/Kconfig

@@ -24,6 +24,7 @@ source "drivers/net/ethernet/brocade/Kconfig"
 source "drivers/net/ethernet/chelsio/Kconfig"
 source "drivers/net/ethernet/cirrus/Kconfig"
 source "drivers/net/ethernet/cisco/Kconfig"
+source "drivers/net/ethernet/davicom/Kconfig"
 
 config DNET
 	tristate "Dave ethernet support (DNET)"

drivers/net/ethernet/Makefile

@@ -16,6 +16,7 @@ obj-$(CONFIG_NET_VENDOR_BROCADE) += brocade/
 obj-$(CONFIG_NET_VENDOR_CHELSIO) += chelsio/
 obj-$(CONFIG_NET_VENDOR_CIRRUS) += cirrus/
 obj-$(CONFIG_NET_VENDOR_CISCO) += cisco/
+obj-$(CONFIG_DM9000) += davicom/
 obj-$(CONFIG_DNET) += dnet.o
 obj-$(CONFIG_NET_VENDOR_DEC) += dec/
 obj-$(CONFIG_NET_VENDOR_DLINK) += dlink/

drivers/net/ethernet/davicom/Kconfig

+#
+# Davicom device configuration
+#
+
+config DM9000
+	tristate "DM9000 support"
+	depends on ARM || BLACKFIN || MIPS
+	select CRC32
+	select MII
+	---help---
+	  Support for DM9000 chipset.
+
+	  To compile this driver as a module, choose M here.  The module
+	  will be called dm9000.
+
+config DM9000_DEBUGLEVEL
+	int "DM9000 maximum debug level"
+	depends on DM9000
+	default 4
+	---help---
+	  The maximum level of debugging code compiled into the DM9000
+	  driver.
+
+config DM9000_FORCE_SIMPLE_PHY_POLL
+	bool "Force simple NSR based PHY polling"
+	depends on DM9000
+	---help---
+	  This configuration forces the DM9000 to use the NSR's LinkStatus
+	  bit to determine if the link is up or down instead of the more
+	  costly MII PHY reads. Note, this will not work if the chip is
+	  operating with an external PHY.

drivers/net/ethernet/davicom/Makefile

+#
+# Makefile for the Davicom device drivers.
+#
+
+obj-$(CONFIG_DM9000) += dm9000.o