dt-bindings: usb: qcom,dwc3: Convert USB DWC3 bindings

Convert USB DWC3 bindings to DT schema format using json-schema.
Signed-off-by: NSandeep Maheswaram <sanm@codeaurora.org>
Signed-off-by: NFelipe Balbi <balbi@kernel.org>

Documentation/devicetree/bindings/usb/qcom,dwc3.txt

-Qualcomm SuperSpeed DWC3 USB SoC controller
-
-Required properties:
-- compatible:		Compatible list, contains
-			"qcom,dwc3"
-			"qcom,msm8996-dwc3" for msm8996 SOC.
-			"qcom,msm8998-dwc3" for msm8998 SOC.
-			"qcom,sdm845-dwc3" for sdm845 SOC.
-- reg:			Offset and length of register set for QSCRATCH wrapper
-- power-domains:	specifies a phandle to PM domain provider node
-- clocks:		A list of phandle + clock-specifier pairs for the
-				clocks listed in clock-names
-- clock-names:		Should contain the following:
-  "core"		Master/Core clock, have to be >= 125 MHz for SS
-				operation and >= 60MHz for HS operation
-  "mock_utmi"		Mock utmi clock needed for ITP/SOF generation in
-				host mode. Its frequency should be 19.2MHz.
-  "sleep"		Sleep clock, used for wakeup when USB3 core goes
-				into low power mode (U3).
-
-Optional clocks:
-  "iface"		System bus AXI clock.
-			Not present on "qcom,msm8996-dwc3" compatible.
-  "cfg_noc"		System Config NOC clock.
-			Not present on "qcom,msm8996-dwc3" compatible.
-- assigned-clocks:	Should be:
-				MOCK_UTMI_CLK
-				MASTER_CLK
-- assigned-clock-rates: Should be:
-                                19.2Mhz (192000000) for MOCK_UTMI_CLK
-                                >=125Mhz (125000000) for MASTER_CLK in SS mode
-                                >=60Mhz (60000000) for MASTER_CLK in HS mode
-
-Optional properties:
-- resets:		Phandle to reset control that resets core and wrapper.
-- interrupts:		specifies interrupts from controller wrapper used
-			to wakeup from low power/susepnd state.	Must contain
-			one or more entry for interrupt-names property
-- interrupt-names:	Must include the following entries:
-			- "hs_phy_irq": The interrupt that is asserted when a
-			   wakeup event is received on USB2 bus
-			- "ss_phy_irq": The interrupt that is asserted when a
-			   wakeup event is received on USB3 bus
-			- "dm_hs_phy_irq" and "dp_hs_phy_irq": Separate
-			   interrupts for any wakeup event on DM and DP lines
-- qcom,select-utmi-as-pipe-clk: if present, disable USB3 pipe_clk requirement.
-				Used when dwc3 operates without SSPHY and only
-				HS/FS/LS modes are supported.
-
-Required child node:
-A child node must exist to represent the core DWC3 IP block. The name of
-the node is not important. The content of the node is defined in dwc3.txt.
-
-Phy documentation is provided in the following places:
-Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt    - USB3 QMP PHY
-Documentation/devicetree/bindings/phy/qcom,qusb2-phy.yaml - USB2 QUSB2 PHY
-
-Example device nodes:
-
-		hs_phy: phy@100f8800 {
-			compatible = "qcom,qusb2-v2-phy";
-			...
-		};
-
-		ss_phy: phy@100f8830 {
-			compatible = "qcom,qmp-v3-usb3-phy";
-			...
-		};
-
-		usb3_0: usb30@a6f8800 {
-			compatible = "qcom,dwc3";
-			reg = <0xa6f8800 0x400>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-
-			interrupts = <0 131 0>, <0 486 0>, <0 488 0>, <0 489 0>;
-			interrupt-names = "hs_phy_irq", "ss_phy_irq",
-				  "dm_hs_phy_irq", "dp_hs_phy_irq";
-
-			clocks = <&gcc GCC_USB30_PRIM_MASTER_CLK>,
-				<&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
-				<&gcc GCC_USB30_PRIM_SLEEP_CLK>;
-			clock-names = "core", "mock_utmi", "sleep";
-
-			assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
-					  <&gcc GCC_USB30_PRIM_MASTER_CLK>;
-			assigned-clock-rates = <19200000>, <133000000>;
-
-			resets = <&gcc GCC_USB30_PRIM_BCR>;
-			reset-names = "core_reset";
-			power-domains = <&gcc USB30_PRIM_GDSC>;
-			qcom,select-utmi-as-pipe-clk;
-
-			dwc3@10000000 {
-				compatible = "snps,dwc3";
-				reg = <0x10000000 0xcd00>;
-				interrupts = <0 205 0x4>;
-				phys = <&hs_phy>, <&ss_phy>;
-				phy-names = "usb2-phy", "usb3-phy";
-				dr_mode = "host";
-			};
-		};
-

Documentation/devicetree/bindings/usb/qcom,dwc3.yaml

+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/usb/qcom,dwc3.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm SuperSpeed DWC3 USB SoC controller
+
+maintainers:
+  - Manu Gautam <mgautam@codeaurora.org>
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - qcom,msm8996-dwc3
+          - qcom,msm8998-dwc3
+          - qcom,sdm845-dwc3
+      - const: qcom,dwc3
+
+  reg:
+    description: Offset and length of register set for QSCRATCH wrapper
+    maxItems: 1
+
+  "#address-cells":
+    enum: [ 1, 2 ]
+
+  "#size-cells":
+    enum: [ 1, 2 ]
+
+  power-domains:
+    description: specifies a phandle to PM domain provider node
+    maxItems: 1
+
+  clocks:
+    description:
+      A list of phandle and clock-specifier pairs for the clocks
+      listed in clock-names.
+    items:
+      - description: System Config NOC clock.
+      - description: Master/Core clock, has to be >= 125 MHz
+          for SS operation and >= 60MHz for HS operation.
+      - description: System bus AXI clock.
+      - description: Mock utmi clock needed for ITP/SOF generation
+          in host mode. Its frequency should be 19.2MHz.
+      - description: Sleep clock, used for wakeup when
+          USB3 core goes into low power mode (U3).
+
+  clock-names:
+    items:
+      - const: cfg_noc
+      - const: core
+      - const: iface
+      - const: mock_utmi
+      - const: sleep
+
+  assigned-clocks:
+    items:
+      - description: Phandle and clock specifier of MOCK_UTMI_CLK.
+      - description: Phandle and clock specifoer of MASTER_CLK.
+
+  assigned-clock-rates:
+    maxItems: 2
+    items:
+      - description: Must be 19.2MHz (19200000).
+      - description: Must be >= 60 MHz in HS mode, >= 125 MHz in SS mode.
+
+  resets:
+    maxItems: 1
+
+  interrupts:
+    items:
+      - description: The interrupt that is asserted
+          when a wakeup event is received on USB2 bus.
+      - description: The interrupt that is asserted
+          when a wakeup event is received on USB3 bus.
+      - description: Wakeup event on DM line.
+      - description: Wakeup event on DP line.
+
+  interrupt-names:
+    items:
+      - const: hs_phy_irq
+      - const: ss_phy_irq
+      - const: dm_hs_phy_irq
+      - const: dp_hs_phy_irq
+
+  qcom,select-utmi-as-pipe-clk:
+    description:
+      If present, disable USB3 pipe_clk requirement.
+      Used when dwc3 operates without SSPHY and only
+      HS/FS/LS modes are supported.
+    type: boolean
+
+# Required child node:
+
+patternProperties:
+  "^dwc3@[0-9a-f]+$":
+    type: object
+    description:
+      A child node must exist to represent the core DWC3 IP block
+      The content of the node is defined in dwc3.txt.
+
+required:
+  - compatible
+  - reg
+  - "#address-cells"
+  - "#size-cells"
+  - power-domains
+  - clocks
+  - clock-names
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,gcc-sdm845.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    usb@a6f8800 {
+        compatible = "qcom,sdm845-dwc3", "qcom,dwc3";
+        reg = <0 0x0a6f8800 0 0x400>;
+
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
+                 <&gcc GCC_USB30_PRIM_MASTER_CLK>,
+                 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
+                 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+                 <&gcc GCC_USB30_PRIM_SLEEP_CLK>;
+        clock-names = "cfg_noc", "core", "iface", "mock_utmi",
+                      "sleep";
+
+        assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+                          <&gcc GCC_USB30_PRIM_MASTER_CLK>;
+        assigned-clock-rates = <19200000>, <150000000>;
+
+        interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 486 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 488 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 489 IRQ_TYPE_LEVEL_HIGH>;
+        interrupt-names = "hs_phy_irq", "ss_phy_irq",
+                          "dm_hs_phy_irq", "dp_hs_phy_irq";
+
+        power-domains = <&gcc USB30_PRIM_GDSC>;
+
+        resets = <&gcc GCC_USB30_PRIM_BCR>;
+
+        dwc3@a600000 {
+            compatible = "snps,dwc3";
+            reg = <0 0x0a600000 0 0xcd00>;
+            interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+            iommus = <&apps_smmu 0x740 0>;
+            snps,dis_u2_susphy_quirk;
+            snps,dis_enblslpm_quirk;
+            phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
+            phy-names = "usb2-phy", "usb3-phy";
+        };
+    };