hwmon: (it87) Add support for the ITE IT8603E

Add support for IT8603E.

This closes bug #57861:
https://bugzilla.kernel.org/show_bug.cgi?id=57861

[JD: Fixes and clean-ups.]
Signed-off-by: NRudolf Marek <r.marek@assembler.cz>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Documentation/hwmon/it87

@@ -2,6 +2,10 @@ Kernel driver it87
 ==================
 
 Supported chips:
+  * IT8603E
+    Prefix: 'it8603'
+    Addresses scanned: from Super I/O config space (8 I/O ports)
+    Datasheet: Not publicly available
   * IT8705F
     Prefix: 'it87'
     Addresses scanned: from Super I/O config space (8 I/O ports)
@@ -90,7 +94,7 @@ motherboard models.
 Description
 -----------
 
-This driver implements support for the IT8705F, IT8712F, IT8716F,
+This driver implements support for the IT8603E, IT8705F, IT8712F, IT8716F,
 IT8718F, IT8720F, IT8721F, IT8726F, IT8728F, IT8758E, IT8771E, IT8772E,
 IT8782F, IT8783E/F, and SiS950 chips.
 
@@ -129,6 +133,10 @@ to userspace applications.
 The IT8728F, IT8771E, and IT8772E are considered compatible with the IT8721F,
 until a datasheet becomes available (hopefully.)
 
+The IT8603E is a custom design, hardware monitoring part is similar to
+IT8728F. It only supports 16-bit fan mode, the full speed mode of the
+fan is not supported (value 0 of pwmX_enable).
+
 Temperatures are measured in degrees Celsius. An alarm is triggered once
 when the Overtemperature Shutdown limit is crossed.
 
@@ -145,13 +153,16 @@ alarm is triggered if the voltage has crossed a programmable minimum or
 maximum limit. Note that minimum in this case always means 'closest to
 zero'; this is important for negative voltage measurements. All voltage
 inputs can measure voltages between 0 and 4.08 volts, with a resolution of
-0.016 volt (except IT8721F/IT8758E and IT8728F: 0.012 volt.) The battery
-voltage in8 does not have limit registers.
-
-On the IT8721F/IT8758E, IT8782F, and IT8783E/F, some voltage inputs are
-internal and scaled inside the chip (in7 (optional for IT8782F and IT8783E/F),
-in8 and optionally in3). The driver handles this transparently so user-space
-doesn't have to care.
+0.016 volt (except IT8603E, IT8721F/IT8758E and IT8728F: 0.012 volt.) The
+battery voltage in8 does not have limit registers.
+
+On the IT8603E, IT8721F/IT8758E, IT8782F, and IT8783E/F, some voltage inputs
+are internal and scaled inside the chip:
+* in3 (optional)
+* in7 (optional for IT8782F and IT8783E/F)
+* in8 (always)
+* in9 (relevant for IT8603E only)
+The driver handles this transparently so user-space doesn't have to care.
 
 The VID lines (IT8712F/IT8716F/IT8718F/IT8720F) encode the core voltage value:
 the voltage level your processor should work with. This is hardcoded by

drivers/hwmon/Kconfig

@@ -573,8 +573,8 @@ config SENSORS_IT87
 	help
 	  If you say yes here you get support for ITE IT8705F, IT8712F,
 	  IT8716F, IT8718F, IT8720F, IT8721F, IT8726F, IT8728F, IT8758E,
-	  IT8771E, IT8772E, IT8782F, and IT8783E/F sensor chips, and the
-	  SiS950 clone.
+	  IT8771E, IT8772E, IT8782F, IT8783E/F and IT8603E sensor chips,
+	  and the SiS950 clone.
 
 	  This driver can also be built as a module.  If so, the module
 	  will be called it87.

drivers/hwmon/it87.c

@@ -10,7 +10,8 @@
  *  This driver supports only the Environment Controller in the IT8705F and
  *  similar parts.  The other devices are supported by different drivers.
  *
- *  Supports: IT8705F  Super I/O chip w/LPC interface
+ *  Supports: IT8603E  Super I/O chip w/LPC interface
+ *            IT8705F  Super I/O chip w/LPC interface
  *            IT8712F  Super I/O chip w/LPC interface
  *            IT8716F  Super I/O chip w/LPC interface
  *            IT8718F  Super I/O chip w/LPC interface
@@ -64,7 +65,7 @@
 #define DRVNAME "it87"
 
 enum chips { it87, it8712, it8716, it8718, it8720, it8721, it8728, it8771,
-	     it8772, it8782, it8783 };
+	     it8772, it8782, it8783, it8603 };
 
 static unsigned short force_id;
 module_param(force_id, ushort, 0);
@@ -146,6 +147,7 @@ static inline void superio_exit(void)
 #define IT8772E_DEVID 0x8772
 #define IT8782F_DEVID 0x8782
 #define IT8783E_DEVID 0x8783
+#define IT8306E_DEVID 0x8603
 #define IT87_ACT_REG  0x30
 #define IT87_BASE_REG 0x60
 
@@ -315,6 +317,12 @@ static const struct it87_devices it87_devices[] = {
 		  | FEAT_TEMP_OLD_PECI,
 		.old_peci_mask = 0x4,
 	},
+	[it8603] = {
+		.name = "it8603",
+		.features = FEAT_NEWER_AUTOPWM | FEAT_12MV_ADC | FEAT_16BIT_FANS
+		  | FEAT_TEMP_OFFSET | FEAT_TEMP_PECI,
+		.peci_mask = 0x07,
+	},
 };
 
 #define has_16bit_fans(data)	((data)->features & FEAT_16BIT_FANS)
@@ -361,7 +369,7 @@ struct it87_data {
 	unsigned long last_updated;	/* In jiffies */
 
 	u16 in_scaled;		/* Internal voltage sensors are scaled */
-	u8 in[9][3];		/* [nr][0]=in, [1]=min, [2]=max */
+	u8 in[10][3];		/* [nr][0]=in, [1]=min, [2]=max */
 	u8 has_fan;		/* Bitfield, fans enabled */
 	u16 fan[5][2];		/* Register values, [nr][0]=fan, [1]=min */
 	u8 has_temp;		/* Bitfield, temp sensors enabled */
@@ -578,6 +586,7 @@ static SENSOR_DEVICE_ATTR_2(in7_max, S_IRUGO | S_IWUSR, show_in, set_in,
 			    7, 2);
 
 static SENSOR_DEVICE_ATTR_2(in8_input, S_IRUGO, show_in, NULL, 8, 0);
+static SENSOR_DEVICE_ATTR_2(in9_input, S_IRUGO, show_in, NULL, 9, 0);
 
 /* 3 temperatures */
 static ssize_t show_temp(struct device *dev, struct device_attribute *attr,
@@ -734,7 +743,7 @@ static int pwm_mode(const struct it87_data *data, int nr)
 {
 	int ctrl = data->fan_main_ctrl & (1 << nr);
 
-	if (ctrl == 0)					/* Full speed */
+	if (ctrl == 0 && data->type != it8603)		/* Full speed */
 		return 0;
 	if (data->pwm_ctrl[nr] & 0x80)			/* Automatic mode */
 		return 2;
@@ -929,6 +938,10 @@ static ssize_t set_pwm_enable(struct device *dev,
 			return -EINVAL;
 	}
 
+	/* IT8603E does not have on/off mode */
+	if (val == 0 && data->type == it8603)
+		return -EINVAL;
+
 	mutex_lock(&data->update_lock);
 
 	if (val == 0) {
@@ -948,10 +961,13 @@ static ssize_t set_pwm_enable(struct device *dev,
 		else					/* Automatic mode */
 			data->pwm_ctrl[nr] = 0x80 | data->pwm_temp_map[nr];
 		it87_write_value(data, IT87_REG_PWM(nr), data->pwm_ctrl[nr]);
-		/* set SmartGuardian mode */
-		data->fan_main_ctrl |= (1 << nr);
-		it87_write_value(data, IT87_REG_FAN_MAIN_CTRL,
-				 data->fan_main_ctrl);
+
+		if (data->type != it8603) {
+			/* set SmartGuardian mode */
+			data->fan_main_ctrl |= (1 << nr);
+			it87_write_value(data, IT87_REG_FAN_MAIN_CTRL,
+					 data->fan_main_ctrl);
+		}
 	}
 
 	mutex_unlock(&data->update_lock);
@@ -1415,6 +1431,8 @@ static ssize_t show_label(struct device *dev, struct device_attribute *attr,
 static SENSOR_DEVICE_ATTR(in3_label, S_IRUGO, show_label, NULL, 0);
 static SENSOR_DEVICE_ATTR(in7_label, S_IRUGO, show_label, NULL, 1);
 static SENSOR_DEVICE_ATTR(in8_label, S_IRUGO, show_label, NULL, 2);
+/* special AVCC3 IT8306E in9 */
+static SENSOR_DEVICE_ATTR(in9_label, S_IRUGO, show_label, NULL, 0);
 
 static ssize_t show_name(struct device *dev, struct device_attribute
 			 *devattr, char *buf)
@@ -1424,7 +1442,7 @@ static ssize_t show_name(struct device *dev, struct device_attribute
 }
 static DEVICE_ATTR(name, S_IRUGO, show_name, NULL);
 
-static struct attribute *it87_attributes_in[9][5] = {
+static struct attribute *it87_attributes_in[10][5] = {
 {
 	&sensor_dev_attr_in0_input.dev_attr.attr,
 	&sensor_dev_attr_in0_min.dev_attr.attr,
@@ -1476,9 +1494,12 @@ static struct attribute *it87_attributes_in[9][5] = {
 }, {
 	&sensor_dev_attr_in8_input.dev_attr.attr,
 	NULL
+}, {
+	&sensor_dev_attr_in9_input.dev_attr.attr,
+	NULL
 } };
 
-static const struct attribute_group it87_group_in[9] = {
+static const struct attribute_group it87_group_in[10] = {
 	{ .attrs = it87_attributes_in[0] },
 	{ .attrs = it87_attributes_in[1] },
 	{ .attrs = it87_attributes_in[2] },
@@ -1488,6 +1509,7 @@ static const struct attribute_group it87_group_in[9] = {
 	{ .attrs = it87_attributes_in[6] },
 	{ .attrs = it87_attributes_in[7] },
 	{ .attrs = it87_attributes_in[8] },
+	{ .attrs = it87_attributes_in[9] },
 };
 
 static struct attribute *it87_attributes_temp[3][6] = {
@@ -1546,7 +1568,8 @@ static struct attribute *it87_attributes_in_beep[] = {
 	&sensor_dev_attr_in5_beep.dev_attr.attr,
 	&sensor_dev_attr_in6_beep.dev_attr.attr,
 	&sensor_dev_attr_in7_beep.dev_attr.attr,
-	NULL
+	NULL,
+	NULL,
 };
 
 static struct attribute *it87_attributes_temp_beep[] = {
@@ -1685,6 +1708,7 @@ static struct attribute *it87_attributes_label[] = {
 	&sensor_dev_attr_in3_label.dev_attr.attr,
 	&sensor_dev_attr_in7_label.dev_attr.attr,
 	&sensor_dev_attr_in8_label.dev_attr.attr,
+	&sensor_dev_attr_in9_label.dev_attr.attr,
 	NULL
 };
 
@@ -1742,6 +1766,9 @@ static int __init it87_find(unsigned short *address,
 	case IT8783E_DEVID:
 		sio_data->type = it8783;
 		break;
+	case IT8306E_DEVID:
+		sio_data->type = it8603;
+		break;
 	case 0xffff:	/* No device at all */
 		goto exit;
 	default:
@@ -1763,11 +1790,15 @@ static int __init it87_find(unsigned short *address,
 
 	err = 0;
 	sio_data->revision = superio_inb(DEVREV) & 0x0f;
-	pr_info("Found IT%04xF chip at 0x%x, revision %d\n",
-		chip_type, *address, sio_data->revision);
+	pr_info("Found IT%04x%c chip at 0x%x, revision %d\n", chip_type,
+		chip_type == 0x8603 ? 'E' : 'F', *address,
+		sio_data->revision);
 
 	/* in8 (Vbat) is always internal */
 	sio_data->internal = (1 << 2);
+	/* Only the IT8603E has in9 */
+	if (sio_data->type != it8603)
+		sio_data->skip_in |= (1 << 9);
 
 	/* Read GPIO config and VID value from LDN 7 (GPIO) */
 	if (sio_data->type == it87) {
@@ -1844,7 +1875,38 @@ static int __init it87_find(unsigned short *address,
 			sio_data->internal |= (1 << 1);
 
 		sio_data->beep_pin = superio_inb(IT87_SIO_BEEP_PIN_REG) & 0x3f;
+	} else if (sio_data->type == it8603) {
+		int reg27, reg29;
+
+		sio_data->skip_vid = 1;	/* No VID */
+		superio_select(GPIO);
 
+		reg27 = superio_inb(IT87_SIO_GPIO3_REG);
+
+		/* Check if fan3 is there or not */
+		if (reg27 & (1 << 6))
+			sio_data->skip_pwm |= (1 << 2);
+		if (reg27 & (1 << 7))
+			sio_data->skip_fan |= (1 << 2);
+
+		/* Check if fan2 is there or not */
+		reg29 = superio_inb(IT87_SIO_GPIO5_REG);
+		if (reg29 & (1 << 1))
+			sio_data->skip_pwm |= (1 << 1);
+		if (reg29 & (1 << 2))
+			sio_data->skip_fan |= (1 << 1);
+
+		sio_data->skip_in |= (1 << 5); /* No VIN5 */
+		sio_data->skip_in |= (1 << 6); /* No VIN6 */
+
+		/* no fan4 */
+		sio_data->skip_pwm |= (1 << 3);
+		sio_data->skip_fan |= (1 << 3);
+
+		sio_data->internal |= (1 << 1); /* in7 is VSB */
+		sio_data->internal |= (1 << 3); /* in9 is AVCC */
+
+		sio_data->beep_pin = superio_inb(IT87_SIO_BEEP_PIN_REG) & 0x3f;
 	} else {
 		int reg;
 		bool uart6;
@@ -1966,7 +2028,7 @@ static void it87_remove_files(struct device *dev)
 	int i;
 
 	sysfs_remove_group(&dev->kobj, &it87_group);
-	for (i = 0; i < 9; i++) {
+	for (i = 0; i < 10; i++) {
 		if (sio_data->skip_in & (1 << i))
 			continue;
 		sysfs_remove_group(&dev->kobj, &it87_group_in[i]);
@@ -2080,6 +2142,8 @@ static int it87_probe(struct platform_device *pdev)
 			data->in_scaled |= (1 << 7);	/* in7 is VSB */
 		if (sio_data->internal & (1 << 2))
 			data->in_scaled |= (1 << 8);	/* in8 is Vbat */
+		if (sio_data->internal & (1 << 3))
+			data->in_scaled |= (1 << 9);	/* in9 is AVCC */
 	} else if (sio_data->type == it8782 || sio_data->type == it8783) {
 		if (sio_data->internal & (1 << 0))
 			data->in_scaled |= (1 << 3);	/* in3 is VCC5V */
@@ -2102,7 +2166,7 @@ static int it87_probe(struct platform_device *pdev)
 	if (err)
 		return err;
 
-	for (i = 0; i < 9; i++) {
+	for (i = 0; i < 10; i++) {
 		if (sio_data->skip_in & (1 << i))
 			continue;
 		err = sysfs_create_group(&dev->kobj, &it87_group_in[i]);
@@ -2202,7 +2266,7 @@ static int it87_probe(struct platform_device *pdev)
 	}
 
 	/* Export labels for internal sensors */
-	for (i = 0; i < 3; i++) {
+	for (i = 0; i < 4; i++) {
 		if (!(sio_data->internal & (1 << i)))
 			continue;
 		err = sysfs_create_file(&dev->kobj,
@@ -2383,8 +2447,9 @@ static void it87_init_device(struct platform_device *pdev)
 	}
 	data->has_fan = (data->fan_main_ctrl >> 4) & 0x07;
 
-	/* Set tachometers to 16-bit mode if needed */
-	if (has_16bit_fans(data)) {
+	/* Set tachometers to 16-bit mode if needed, IT8603E (and IT8728F?)
+	 * has it by default */
+	if (has_16bit_fans(data) && data->type != it8603) {
 		tmp = it87_read_value(data, IT87_REG_FAN_16BIT);
 		if (~tmp & 0x07 & data->has_fan) {
 			dev_dbg(&pdev->dev,
@@ -2464,6 +2529,8 @@ static struct it87_data *it87_update_device(struct device *dev)
 		}
 		/* in8 (battery) has no limit registers */
 		data->in[8][0] = it87_read_value(data, IT87_REG_VIN(8));
+		if (data->type == it8603)
+			data->in[9][0] = it87_read_value(data, 0x2f);
 
 		for (i = 0; i < 5; i++) {
 			/* Skip disabled fans */