提交 be346ffa 编写于 作者: V Vlad Yasevich 提交者: David S. Miller

vlan: Correctly propagate promisc|allmulti flags in notifier.

Currently vlan notifier handler will try to update all vlans
for a device when that device comes up.  A problem occurs,
however, when the vlan device was set to promiscuous, but not
by the user (ex: a bridge).  In that case, dev->gflags are
not updated.  What results is that the lower device ends
up with an extra promiscuity count.  Here are the
backtraces that prove this:
[62852.052179]  [<ffffffff814fe248>] __dev_set_promiscuity+0x38/0x1e0
[62852.052186]  [<ffffffff8160bcbb>] ? _raw_spin_unlock_bh+0x1b/0x40
[62852.052188]  [<ffffffff814fe4be>] ? dev_set_rx_mode+0x2e/0x40
[62852.052190]  [<ffffffff814fe694>] dev_set_promiscuity+0x24/0x50
[62852.052194]  [<ffffffffa0324795>] vlan_dev_open+0xd5/0x1f0 [8021q]
[62852.052196]  [<ffffffff814fe58f>] __dev_open+0xbf/0x140
[62852.052198]  [<ffffffff814fe88d>] __dev_change_flags+0x9d/0x170
[62852.052200]  [<ffffffff814fe989>] dev_change_flags+0x29/0x60

The above comes from the setting the vlan device to IFF_UP state.

[62852.053569]  [<ffffffff814fe248>] __dev_set_promiscuity+0x38/0x1e0
[62852.053571]  [<ffffffffa032459b>] ? vlan_dev_set_rx_mode+0x2b/0x30
[8021q]
[62852.053573]  [<ffffffff814fe8d5>] __dev_change_flags+0xe5/0x170
[62852.053645]  [<ffffffff814fe989>] dev_change_flags+0x29/0x60
[62852.053647]  [<ffffffffa032334a>] vlan_device_event+0x18a/0x690
[8021q]
[62852.053649]  [<ffffffff8161036c>] notifier_call_chain+0x4c/0x70
[62852.053651]  [<ffffffff8109d456>] raw_notifier_call_chain+0x16/0x20
[62852.053653]  [<ffffffff814f744d>] call_netdevice_notifiers+0x2d/0x60
[62852.053654]  [<ffffffff814fe1a3>] __dev_notify_flags+0x33/0xa0
[62852.053656]  [<ffffffff814fe9b2>] dev_change_flags+0x52/0x60
[62852.053657]  [<ffffffff8150cd57>] do_setlink+0x397/0xa40

And this one comes from the notification code.  What we end
up with is a vlan with promiscuity count of 1 and and a physical
device with a promiscuity count of 2.  They should both have
a count 1.

To resolve this issue, vlan code can use dev_get_flags() api
which correctly masks promiscuity and allmulti flags.
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
上级 110bc767
......@@ -443,7 +443,7 @@ static int vlan_device_event(struct notifier_block *unused, unsigned long event,
case NETDEV_UP:
/* Put all VLANs for this dev in the up state too. */
vlan_group_for_each_dev(grp, i, vlandev) {
flgs = vlandev->flags;
flgs = dev_get_flags(vlandev);
if (flgs & IFF_UP)
continue;
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册