提交 b2ba08e6 编写于 作者: J Joe Perches 提交者: David S. Miller

forcedeth: Convert dev_printk(<level> to dev_<level>(

Use vsprintf extension %pM for a mac address in one instance.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
上级 cd66328b
......@@ -5442,8 +5442,7 @@ static int __devinit nv_probe(struct pci_dev *pci_dev, const struct pci_device_i
}
}
if (i == DEVICE_COUNT_RESOURCE) {
dev_printk(KERN_INFO, &pci_dev->dev,
"Couldn't find register window\n");
dev_info(&pci_dev->dev, "Couldn't find register window\n");
goto out_relreg;
}
......@@ -5459,13 +5458,13 @@ static int __devinit nv_probe(struct pci_dev *pci_dev, const struct pci_device_i
np->txrxctl_bits = NVREG_TXRXCTL_DESC_3;
if (dma_64bit) {
if (pci_set_dma_mask(pci_dev, DMA_BIT_MASK(39)))
dev_printk(KERN_INFO, &pci_dev->dev,
"64-bit DMA failed, using 32-bit addressing\n");
dev_info(&pci_dev->dev,
"64-bit DMA failed, using 32-bit addressing\n");
else
dev->features |= NETIF_F_HIGHDMA;
if (pci_set_consistent_dma_mask(pci_dev, DMA_BIT_MASK(39))) {
dev_printk(KERN_INFO, &pci_dev->dev,
"64-bit DMA (consistent) failed, using 32-bit ring buffers\n");
dev_info(&pci_dev->dev,
"64-bit DMA (consistent) failed, using 32-bit ring buffers\n");
}
}
} else if (id->driver_data & DEV_HAS_LARGEDESC) {
......@@ -5595,11 +5594,11 @@ static int __devinit nv_probe(struct pci_dev *pci_dev, const struct pci_device_i
* Bad mac address. At least one bios sets the mac address
* to 01:23:45:67:89:ab
*/
dev_printk(KERN_ERR, &pci_dev->dev,
"Invalid Mac address detected: %pM\n",
dev_err(&pci_dev->dev,
"Invalid MAC address detected: %pM\n",
dev->dev_addr);
dev_printk(KERN_ERR, &pci_dev->dev,
"Please complain to your hardware vendor. Switching to a random MAC.\n");
dev_err(&pci_dev->dev,
"Please complain to your hardware vendor. Switched to a random MAC address.\n");
random_ether_addr(dev->dev_addr);
}
......@@ -5752,8 +5751,7 @@ static int __devinit nv_probe(struct pci_dev *pci_dev, const struct pci_device_i
break;
}
if (i == 33) {
dev_printk(KERN_INFO, &pci_dev->dev,
"open: Could not find a valid PHY.\n");
dev_info(&pci_dev->dev, "open: Could not find a valid PHY\n");
goto out_error;
}
......@@ -5774,37 +5772,27 @@ static int __devinit nv_probe(struct pci_dev *pci_dev, const struct pci_device_i
err = register_netdev(dev);
if (err) {
dev_printk(KERN_INFO, &pci_dev->dev,
"unable to register netdev: %d\n", err);
dev_info(&pci_dev->dev, "unable to register netdev: %d\n", err);
goto out_error;
}
dev_printk(KERN_INFO, &pci_dev->dev, "ifname %s, PHY OUI 0x%x @ %d, "
"addr %2.2x:%2.2x:%2.2x:%2.2x:%2.2x:%2.2x\n",
dev->name,
np->phy_oui,
np->phyaddr,
dev->dev_addr[0],
dev->dev_addr[1],
dev->dev_addr[2],
dev->dev_addr[3],
dev->dev_addr[4],
dev->dev_addr[5]);
dev_printk(KERN_INFO, &pci_dev->dev, "%s%s%s%s%s%s%s%s%s%sdesc-v%u\n",
dev->features & NETIF_F_HIGHDMA ? "highdma " : "",
dev->features & (NETIF_F_IP_CSUM | NETIF_F_SG) ?
dev_info(&pci_dev->dev, "ifname %s, PHY OUI 0x%x @ %d, addr %pM\n",
dev->name, np->phy_oui, np->phyaddr, dev->dev_addr);
dev_info(&pci_dev->dev, "%s%s%s%s%s%s%s%s%s%sdesc-v%u\n",
dev->features & NETIF_F_HIGHDMA ? "highdma " : "",
dev->features & (NETIF_F_IP_CSUM | NETIF_F_SG) ?
"csum " : "",
dev->features & (NETIF_F_HW_VLAN_RX | NETIF_F_HW_VLAN_TX) ?
dev->features & (NETIF_F_HW_VLAN_RX | NETIF_F_HW_VLAN_TX) ?
"vlan " : "",
id->driver_data & DEV_HAS_POWER_CNTRL ? "pwrctl " : "",
id->driver_data & DEV_HAS_MGMT_UNIT ? "mgmt " : "",
id->driver_data & DEV_NEED_TIMERIRQ ? "timirq " : "",
np->gigabit == PHY_GIGABIT ? "gbit " : "",
np->need_linktimer ? "lnktim " : "",
np->msi_flags & NV_MSI_CAPABLE ? "msi " : "",
np->msi_flags & NV_MSI_X_CAPABLE ? "msi-x " : "",
np->desc_ver);
id->driver_data & DEV_HAS_POWER_CNTRL ? "pwrctl " : "",
id->driver_data & DEV_HAS_MGMT_UNIT ? "mgmt " : "",
id->driver_data & DEV_NEED_TIMERIRQ ? "timirq " : "",
np->gigabit == PHY_GIGABIT ? "gbit " : "",
np->need_linktimer ? "lnktim " : "",
np->msi_flags & NV_MSI_CAPABLE ? "msi " : "",
np->msi_flags & NV_MSI_X_CAPABLE ? "msi-x " : "",
np->desc_ver);
return 0;
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册