xilinx/ll_temac: Move the Xilinx drivers

Move the Xilinx drivers into drivers/net/ethernet/xilinx/ and
make the necessary Kconfig and Makefile changes.

CC: John Williams <john.williams@petalogix.com>
CC: "David H. Lynch Jr." <dhlii@dlasys.net>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

drivers/net/Kconfig

@@ -493,13 +493,6 @@ config NET_POCKET
 	  the questions about this class of network devices. If you say Y, you
 	  will be asked for your specific device in the following questions.
 
-config XILINX_EMACLITE
-	tristate "Xilinx 10/100 Ethernet Lite support"
-	depends on PPC32 || MICROBLAZE
-	select PHYLIB
-	help
-	  This driver supports the 10/100 Ethernet Lite from Xilinx.
-
 config LANTIQ_ETOP
 	tristate "Lantiq SoC ETOP driver"
 	depends on SOC_TYPE_XWAY
@@ -539,14 +532,6 @@ config IP1000
 	  To compile this driver as a module, choose M here: the module
 	  will be called ipg.  This is recommended.
 
-config XILINX_LL_TEMAC
-	tristate "Xilinx LL TEMAC (LocalLink Tri-mode Ethernet MAC) driver"
-	depends on PPC || MICROBLAZE
-	select PHYLIB
-	help
-	  This driver supports the Xilinx 10/100/1000 LocalLink TEMAC
-	  core used in Xilinx Spartan and Virtex FPGAs
-
 endif # NETDEV_1000
 
 #

drivers/net/Makefile

@@ -33,10 +33,6 @@ obj-$(CONFIG_NET_SB1000) += sb1000.o
 obj-$(CONFIG_HP100) += hp100.o
 obj-$(CONFIG_FORCEDETH) += forcedeth.o
 
-ll_temac-objs := ll_temac_main.o ll_temac_mdio.o
-obj-$(CONFIG_XILINX_LL_TEMAC) += ll_temac.o
-obj-$(CONFIG_XILINX_EMACLITE) += xilinx_emaclite.o
-
 obj-$(CONFIG_PPP) += ppp_generic.o
 obj-$(CONFIG_PPP_ASYNC) += ppp_async.o
 obj-$(CONFIG_PPP_SYNC_TTY) += ppp_synctty.o

drivers/net/ethernet/Kconfig

@@ -82,5 +82,6 @@ source "drivers/net/ethernet/ti/Kconfig"
 source "drivers/net/ethernet/toshiba/Kconfig"
 source "drivers/net/ethernet/tundra/Kconfig"
 source "drivers/net/ethernet/via/Kconfig"
+source "drivers/net/ethernet/xilinx/Kconfig"
 
 endif # ETHERNET

drivers/net/ethernet/Makefile

@@ -50,3 +50,4 @@ obj-$(CONFIG_NET_VENDOR_TI) += ti/
 obj-$(CONFIG_NET_VENDOR_TOSHIBA) += toshiba/
 obj-$(CONFIG_NET_VENDOR_TUNDRA) += tundra/
 obj-$(CONFIG_NET_VENDOR_VIA) += via/
+obj-$(CONFIG_NET_VENDOR_XILINX) += xilinx/

drivers/net/ethernet/xilinx/Kconfig

+#
+# Xilink device configuration
+#
+
+config NET_VENDOR_XILINX
+	bool "Xilinx devices"
+	depends on PPC || PPC32 || MICROBLAZE
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about Xilinx devices. If you say Y, you will be asked
+	  for your specific card in the following questions.
+
+if NET_VENDOR_XILINX
+
+config XILINX_EMACLITE
+	tristate "Xilinx 10/100 Ethernet Lite support"
+	depends on (PPC32 || MICROBLAZE)
+	select PHYLIB
+	---help---
+	  This driver supports the 10/100 Ethernet Lite from Xilinx.
+
+config XILINX_LL_TEMAC
+	tristate "Xilinx LL TEMAC (LocalLink Tri-mode Ethernet MAC) driver"
+	depends on (PPC || MICROBLAZE)
+	select PHYLIB
+	---help---
+	  This driver supports the Xilinx 10/100/1000 LocalLink TEMAC
+	  core used in Xilinx Spartan and Virtex FPGAs
+
+endif # NET_VENDOR_XILINX

drivers/net/ethernet/xilinx/Makefile

+#
+# Makefile for the Xilink network device drivers.
+#
+
+ll_temac-objs := ll_temac_main.o ll_temac_mdio.o
+obj-$(CONFIG_XILINX_LL_TEMAC) += ll_temac.o
+obj-$(CONFIG_XILINX_EMACLITE) += xilinx_emaclite.o