Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
提交 ae0407e1 编写于 作者: L Linus Walleij
浏览文件
操作

Merge branch 'j/pinctrl' of http://github.com/at91linux/linux-at91 into at91

上级 ddffeb8c 251e783a
展开全部 隐藏空白更改
内联 并排
Showing with 2768 addition and 446 deletion
Documentation/devicetree/bindings/gpio/gpio_atmel.txt
浏览文件 @ ae0407e1
......@@ -9,6 +9,10 @@ Required properties:
unused).
- gpio-controller: Marks the device node as a GPIO controller.
optional properties:
- #gpio-lines: Number of gpio if absent 32.
Example:
pioA: gpio@fffff200 {
compatible = "atmel,at91rm9200-gpio";
......@@ -16,5 +20,6 @@ Example:
interrupts = <2 4>;
#gpio-cells = <2>;
gpio-controller;
#gpio-lines = <19>;
};
Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt 0 → 100644
浏览文件 @ ae0407e1
* Atmel AT91 Pinmux Controller
The AT91 Pinmux Controler, enables the IC
to share one PAD to several functional blocks. The sharing is done by
multiplexing the PAD input/output signals. For each PAD there are up to
8 muxing options (called periph modes). Since different modules require
different PAD settings (like pull up, keeper, etc) the contoller controls
also the PAD settings parameters.
Please refer to pinctrl-bindings.txt in this directory for details of the
common pinctrl bindings used by client devices, including the meaning of the
phrase "pin configuration node".
Atmel AT91 pin configuration node is a node of a group of pins which can be
used for a specific device or function. This node represents both mux and config
of the pins in that group. The 'pins' selects the function mode(also named pin
mode) this pin can work on and the 'config' configures various pad settings
such as pull-up, multi drive, etc.
Required properties for iomux controller:
- compatible: "atmel,at91rm9200-pinctrl"
- atmel,mux-mask: array of mask (periph per bank) to describe if a pin can be
configured in this periph mode. All the periph and bank need to be describe.
How to create such array:
Each column will represent the possible peripheral of the pinctrl
Each line will represent a pio bank
Take an example on the 9260
Peripheral: 2 ( A and B)
Bank: 3 (A, B and C)
=>
/* A B */
0xffffffff 0xffc00c3b /* pioA */
0xffffffff 0x7fff3ccf /* pioB */
0xffffffff 0x007fffff /* pioC */
For each peripheral/bank we will descibe in a u32 if a pin can can be
configured in it by putting 1 to the pin bit (1 << pin)
Let's take the pioA on peripheral B
From the datasheet Table 10-2.
Peripheral B
PA0 MCDB0
PA1 MCCDB
PA2
PA3 MCDB3
PA4 MCDB2
PA5 MCDB1
PA6
PA7
PA8
PA9
PA10 ETX2
PA11 ETX3
PA12
PA13
PA14
PA15
PA16
PA17
PA18
PA19
PA20
PA21
PA22 ETXER
PA23 ETX2
PA24 ETX3
PA25 ERX2
PA26 ERX3
PA27 ERXCK
PA28 ECRS
PA29 ECOL
PA30 RXD4
PA31 TXD4
=> 0xffc00c3b
Required properties for pin configuration node:
- atmel,pins: 4 integers array, represents a group of pins mux and config
setting. The format is atmel,pins = <PIN_BANK PIN_BANK_NUM PERIPH CONFIG>.
The PERIPH 0 means gpio.
Bits used for CONFIG:
PULL_UP(1 << 0): indicate this pin need a pull up.
MULTIDRIVE(1 << 1): indicate this pin need to be configured as multidrive.
NOTE:
Some requirements for using atmel,at91rm9200-pinctrl binding:
1. We have pin function node defined under at91 controller node to represent
what pinmux functions this SoC supports.
2. The driver can use the function node's name and pin configuration node's
name describe the pin function and group hierarchy.
For example, Linux at91 pinctrl driver takes the function node's name
as the function name and pin configuration node's name as group name to
create the map table.
3. Each pin configuration node should have a phandle, devices can set pins
configurations by referring to the phandle of that pin configuration node.
4. The gpio controller must be describe in the pinctrl simple-bus.
Examples:
pinctrl@fffff400 {
#address-cells = <1>;
#size-cells = <1>;
ranges;
compatible = "atmel,at91rm9200-pinctrl", "simple-bus";
reg = <0xfffff400 0x600>;
atmel,mux-mask = <
/* A B */
0xffffffff 0xffc00c3b /* pioA */
0xffffffff 0x7fff3ccf /* pioB */
0xffffffff 0x007fffff /* pioC */
>;
/* shared pinctrl settings */
dbgu {
pinctrl_dbgu: dbgu-0 {
atmel,pins =
<1 14 0x1 0x0 /* PB14 periph A */
1 15 0x1 0x1>; /* PB15 periph with pullup */
};
};
};
dbgu: serial@fffff200 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffff200 0x200>;
interrupts = <1 4 7>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_dbgu>;
status = "disabled";
};
arch/arm/Kconfig
浏览文件 @ ae0407e1
......@@ -330,6 +330,8 @@ config ARCH_AT91
select IRQ_DOMAIN
select NEED_MACH_GPIO_H
select NEED_MACH_IO_H if PCCARD
select PINCTRL
select PINCTRL_AT91 if USE_OF
help
This enables support for systems based on Atmel
AT91RM9200 and AT91SAM9* processors.
......
arch/arm/boot/dts/Makefile
浏览文件 @ ae0407e1
ifeq ($(CONFIG_OF),y)
dtb-$(CONFIG_ARCH_AT91) += aks-cdu.dtb \
at91sam9263ek.dtb \
at91sam9g20ek_2mmc.dtb \
at91sam9g20ek.dtb \
at91sam9g25ek.dtb \
at91sam9m10g45ek.dtb \
at91sam9n12ek.dtb \
ethernut5.dtb \
evk-pro3.dtb \
kizbox.dtb \
tny_a9260.dtb \
tny_a9263.dtb \
tny_a9g20.dtb \
usb_a9260.dtb \
usb_a9263.dtb \
usb_a9g20.dtb
# Keep at91 dtb files sorted alphabetically for each SoC
# sam9260
dtb-$(CONFIG_ARCH_AT91) += aks-cdu.dtb
dtb-$(CONFIG_ARCH_AT91) += ethernut5.dtb
dtb-$(CONFIG_ARCH_AT91) += evk-pro3.dtb
dtb-$(CONFIG_ARCH_AT91) += tny_a9260.dtb
dtb-$(CONFIG_ARCH_AT91) += usb_a9260.dtb
# sam9263
dtb-$(CONFIG_ARCH_AT91) += at91sam9263ek.dtb
dtb-$(CONFIG_ARCH_AT91) += tny_a9263.dtb
dtb-$(CONFIG_ARCH_AT91) += usb_a9263.dtb
# sam9g20
dtb-$(CONFIG_ARCH_AT91) += at91sam9g20ek.dtb
dtb-$(CONFIG_ARCH_AT91) += at91sam9g20ek_2mmc.dtb
dtb-$(CONFIG_ARCH_AT91) += kizbox.dtb
dtb-$(CONFIG_ARCH_AT91) += tny_a9g20.dtb
dtb-$(CONFIG_ARCH_AT91) += usb_a9g20.dtb
# sam9g45
dtb-$(CONFIG_ARCH_AT91) += at91sam9m10g45ek.dtb
# sam9n12
dtb-$(CONFIG_ARCH_AT91) += at91sam9n12ek.dtb
# sam9x5
dtb-$(CONFIG_ARCH_AT91) += at91sam9g15ek.dtb
dtb-$(CONFIG_ARCH_AT91) += at91sam9g25ek.dtb
dtb-$(CONFIG_ARCH_AT91) += at91sam9g35ek.dtb
dtb-$(CONFIG_ARCH_AT91) += at91sam9x25ek.dtb
dtb-$(CONFIG_ARCH_AT91) += at91sam9x35ek.dtb
dtb-$(CONFIG_ARCH_BCM2835) += bcm2835-rpi-b.dtb
dtb-$(CONFIG_ARCH_DOVE) += dove-cm-a510.dtb \
dove-cubox.dtb \
......
arch/arm/boot/dts/at91sam9260.dtsi
浏览文件 @ ae0407e1
......@@ -98,40 +98,161 @@
interrupts = <26 4 0 27 4 0 28 4 0>;
};
pioA: gpio@fffff400 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff400 0x100>;
interrupts = <2 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
pinctrl@fffff400 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "atmel,at91rm9200-pinctrl", "simple-bus";
ranges = <0xfffff400 0xfffff400 0x600>;
atmel,mux-mask = <
/* A B */
0xffffffff 0xffc00c3b /* pioA */
0xffffffff 0x7fff3ccf /* pioB */
0xffffffff 0x007fffff /* pioC */
>;
/* shared pinctrl settings */
dbgu {
pinctrl_dbgu: dbgu-0 {
atmel,pins =
<1 14 0x1 0x0 /* PB14 periph A */
1 15 0x1 0x1>; /* PB15 periph with pullup */
};
};
pioB: gpio@fffff600 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff600 0x100>;
interrupts = <3 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
uart0 {
pinctrl_uart0: uart0-0 {
atmel,pins =
<1 4 0x1 0x0 /* PB4 periph A */
1 5 0x1 0x0>; /* PB5 periph A */
};
pinctrl_uart0_rts_cts: uart0_rts_cts-0 {
atmel,pins =
<1 26 0x1 0x0 /* PB26 periph A */
1 27 0x1 0x0>; /* PB27 periph A */
};
pinctrl_uart0_dtr_dsr: uart0_dtr_dsr-0 {
atmel,pins =
<1 24 0x1 0x0 /* PB24 periph A */
1 22 0x1 0x0>; /* PB22 periph A */
};
pinctrl_uart0_dcd: uart0_dcd-0 {
atmel,pins =
<1 23 0x1 0x0>; /* PB23 periph A */
};
pinctrl_uart0_ri: uart0_ri-0 {
atmel,pins =
<1 25 0x1 0x0>; /* PB25 periph A */
};
};
pioC: gpio@fffff800 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff800 0x100>;
interrupts = <4 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
uart1 {
pinctrl_uart1: uart1-0 {
atmel,pins =
<2 6 0x1 0x1 /* PB6 periph A with pullup */
2 7 0x1 0x0>; /* PB7 periph A */
};
pinctrl_uart1_rts_cts: uart1_rts_cts-0 {
atmel,pins =
<1 28 0x1 0x0 /* PB28 periph A */
1 29 0x1 0x0>; /* PB29 periph A */
};
};
uart2 {
pinctrl_uart2: uart2-0 {
atmel,pins =
<1 8 0x1 0x1 /* PB8 periph A with pullup */
1 9 0x1 0x0>; /* PB9 periph A */
};
pinctrl_uart2_rts_cts: uart2_rts_cts-0 {
atmel,pins =
<0 4 0x1 0x0 /* PA4 periph A */
0 5 0x1 0x0>; /* PA5 periph A */
};
};
uart3 {
pinctrl_uart3: uart3-0 {
atmel,pins =
<2 10 0x1 0x1 /* PB10 periph A with pullup */
2 11 0x1 0x0>; /* PB11 periph A */
};
pinctrl_uart3_rts_cts: uart3_rts_cts-0 {
atmel,pins =
<3 8 0x2 0x0 /* PB8 periph B */
3 10 0x2 0x0>; /* PB10 periph B */
};
};
uart4 {
pinctrl_uart4: uart4-0 {
atmel,pins =
<0 31 0x2 0x1 /* PA31 periph B with pullup */
0 30 0x2 0x0>; /* PA30 periph B */
};
};
uart5 {
pinctrl_uart5: uart5-0 {
atmel,pins =
<2 12 0x1 0x1 /* PB12 periph A with pullup */
2 13 0x1 0x0>; /* PB13 periph A */
};
};
nand {
pinctrl_nand: nand-0 {
atmel,pins =
<2 13 0x0 0x1 /* PC13 gpio RDY pin pull_up */
2 14 0x0 0x1>; /* PC14 gpio enable pin pull_up */
};
};
pioA: gpio@fffff400 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff400 0x200>;
interrupts = <2 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
pioB: gpio@fffff600 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff600 0x200>;
interrupts = <3 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
pioC: gpio@fffff800 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff800 0x200>;
interrupts = <4 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
};
dbgu: serial@fffff200 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffff200 0x200>;
interrupts = <1 4 7>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_dbgu>;
status = "disabled";
};
......@@ -141,6 +262,8 @@
interrupts = <6 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart0>;
status = "disabled";
};
......@@ -150,6 +273,8 @@
interrupts = <7 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
status = "disabled";
};
......@@ -159,6 +284,8 @@
interrupts = <8 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
status = "disabled";
};
......@@ -168,6 +295,8 @@
interrupts = <23 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
status = "disabled";
};
......@@ -177,6 +306,8 @@
interrupts = <24 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart4>;
status = "disabled";
};
......@@ -186,6 +317,8 @@
interrupts = <25 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart5>;
status = "disabled";
};
......@@ -257,6 +390,8 @@
>;
atmel,nand-addr-offset = <21>;
atmel,nand-cmd-offset = <22>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_nand>;
gpios = <&pioC 13 0
&pioC 14 0
0
......
arch/arm/boot/dts/at91sam9263.dtsi
浏览文件 @ ae0407e1
......@@ -89,60 +89,137 @@
reg = <0xfffffd10 0x10>;
};
pioA: gpio@fffff200 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff200 0x100>;
interrupts = <2 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
pinctrl@fffff200 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "atmel,at91rm9200-pinctrl", "simple-bus";
ranges = <0xfffff200 0xfffff200 0xa00>;
pioB: gpio@fffff400 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff400 0x100>;
interrupts = <3 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
atmel,mux-mask = <
/* A B */
0xfffffffb 0xffffe07f /* pioA */
0x0007ffff 0x39072fff /* pioB */
0xffffffff 0x3ffffff8 /* pioC */
0xfffffbff 0xffffffff /* pioD */
0xffe00fff 0xfbfcff00 /* pioE */
>;
pioC: gpio@fffff600 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff600 0x100>;
interrupts = <4 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
/* shared pinctrl settings */
dbgu {
pinctrl_dbgu: dbgu-0 {
atmel,pins =
<2 30 0x1 0x0 /* PC30 periph A */
2 31 0x1 0x1>; /* PC31 periph with pullup */
};
};
pioD: gpio@fffff800 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff800 0x100>;
interrupts = <4 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
uart0 {
pinctrl_uart0: uart0-0 {
atmel,pins =
<0 26 0x1 0x1 /* PA26 periph A with pullup */
0 27 0x1 0x0>; /* PA27 periph A */
};
pioE: gpio@fffffa00 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffffa00 0x100>;
interrupts = <4 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
pinctrl_uart0_rts_cts: uart0_rts_cts-0 {
atmel,pins =
<0 28 0x1 0x0 /* PA28 periph A */
0 29 0x1 0x0>; /* PA29 periph A */
};
};
uart1 {
pinctrl_uart1: uart1-0 {
atmel,pins =
<3 0 0x1 0x1 /* PD0 periph A with pullup */
3 1 0x1 0x0>; /* PD1 periph A */
};
pinctrl_uart1_rts_cts: uart1_rts_cts-0 {
atmel,pins =
<3 7 0x2 0x0 /* PD7 periph B */
3 8 0x2 0x0>; /* PD8 periph B */
};
};
uart2 {
pinctrl_uart2: uart2-0 {
atmel,pins =
<3 2 0x1 0x1 /* PD2 periph A with pullup */
3 3 0x1 0x0>; /* PD3 periph A */
};
pinctrl_uart2_rts_cts: uart2_rts_cts-0 {
atmel,pins =
<3 5 0x2 0x0 /* PD5 periph B */
4 6 0x2 0x0>; /* PD6 periph B */
};
};
nand {
pinctrl_nand: nand-0 {
atmel,pins =
<0 22 0x0 0x1 /* PA22 gpio RDY pin pull_up*/
3 15 0x0 0x1>; /* PD15 gpio enable pin pull_up */
};
};
pioA: gpio@fffff200 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff200 0x200>;
interrupts = <2 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
pioB: gpio@fffff400 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff400 0x200>;
interrupts = <3 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
pioC: gpio@fffff600 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff600 0x200>;
interrupts = <4 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
pioD: gpio@fffff800 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff800 0x200>;
interrupts = <4 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
pioE: gpio@fffffa00 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffffa00 0x200>;
interrupts = <4 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
};
dbgu: serial@ffffee00 {
compatible = "atmel,at91sam9260-usart";
reg = <0xffffee00 0x200>;
interrupts = <1 4 7>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_dbgu>;
status = "disabled";
};
......@@ -152,6 +229,8 @@
interrupts = <7 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart0>;
status = "disabled";
};
......@@ -161,6 +240,8 @@
interrupts = <8 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
status = "disabled";
};
......@@ -170,6 +251,8 @@
interrupts = <9 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
status = "disabled";
};
......@@ -206,6 +289,8 @@
>;
atmel,nand-addr-offset = <21>;
atmel,nand-cmd-offset = <22>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_nand>;
gpios = <&pioA 22 0
&pioD 15 0
0
......
arch/arm/boot/dts/at91sam9263ek.dts
浏览文件 @ ae0407e1
......@@ -38,6 +38,7 @@
};
usart0: serial@fff8c000 {
pinctrl-0 = <&pinctrl_uart0 &pinctrl_uart0_rts_cts>;
status = "okay";
};
......
arch/arm/boot/dts/at91sam9g15.dtsi 0 → 100644
浏览文件 @ ae0407e1
/*
* at91sam9g15.dtsi - Device Tree Include file for AT91SAM9G15 SoC
*
* Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
*
* Licensed under GPLv2.
*/
/include/ "at91sam9x5.dtsi"
/ {
model = "Atmel AT91SAM9G15 SoC";
compatible = "atmel, at91sam9g15, atmel,at91sam9x5";
ahb {
apb {
pinctrl@fffff400 {
atmel,mux-mask = <
/* A B C */
0xffffffff 0xffe0399f 0x00000000 /* pioA */
0x00040000 0x00047e3f 0x00000000 /* pioB */
0xfdffffff 0x00000000 0xb83fffff /* pioC */
0x003fffff 0x003f8000 0x00000000 /* pioD */
>;
};
};
};
};
arch/arm/boot/dts/at91sam9g15ek.dts 0 → 100644
浏览文件 @ ae0407e1
/*
* at91sam9g15ek.dts - Device Tree file for AT91SAM9G15-EK board
*
* Copyright (C) 2012 Atmel,
* 2012 Nicolas Ferre <nicolas.ferre@atmel.com>
*
* Licensed under GPLv2 or later.
*/
/dts-v1/;
/include/ "at91sam9g15.dtsi"
/include/ "at91sam9x5ek.dtsi"
/ {
model = "Atmel AT91SAM9G25-EK";
compatible = "atmel,at91sam9g15ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
};
arch/arm/boot/dts/at91sam9g20ek_common.dtsi
浏览文件 @ ae0407e1
......@@ -35,6 +35,12 @@
};
usart0: serial@fffb0000 {
pinctrl-0 =
<&pinctrl_uart0
&pinctrl_uart0_rts_cts
&pinctrl_uart0_dtr_dsr
&pinctrl_uart0_dcd
&pinctrl_uart0_ri>;
status = "okay";
};
......
arch/arm/boot/dts/at91sam9g25.dtsi 0 → 100644
浏览文件 @ ae0407e1
/*
* at91sam9g25.dtsi - Device Tree Include file for AT91SAM9G25 SoC
*
* Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
*
* Licensed under GPLv2.
*/
/include/ "at91sam9x5.dtsi"
/ {
model = "Atmel AT91SAM9G25 SoC";
compatible = "atmel, at91sam9g25, atmel,at91sam9x5";
ahb {
apb {
pinctrl@fffff400 {
atmel,mux-mask = <
/* A B C */
0xffffffff 0xffe0399f 0xc000001c /* pioA */
0x0007ffff 0x8000fe3f 0x00000000 /* pioB */
0x80000000 0x07c0ffff 0xb83fffff /* pioC */
0x003fffff 0x003f8000 0x00000000 /* pioD */
>;
};
};
};
};
arch/arm/boot/dts/at91sam9g25ek.dts
浏览文件 @ ae0407e1
......@@ -7,55 +7,10 @@
* Licensed under GPLv2 or later.
*/
/dts-v1/;
/include/ "at91sam9x5.dtsi"
/include/ "at91sam9x5cm.dtsi"
/include/ "at91sam9g25.dtsi"
/include/ "at91sam9x5ek.dtsi"
/ {
model = "Atmel AT91SAM9G25-EK";
compatible = "atmel,at91sam9g25ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
chosen {
bootargs = "console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=ubifs ubi.mtd=1 root=ubi0:rootfs";
};
ahb {
apb {
dbgu: serial@fffff200 {
status = "okay";
};
usart0: serial@f801c000 {
status = "okay";
};
macb0: ethernet@f802c000 {
phy-mode = "rmii";
status = "okay";
};
i2c0: i2c@f8010000 {
status = "okay";
};
i2c1: i2c@f8014000 {
status = "okay";
};
i2c2: i2c@f8018000 {
status = "okay";
};
};
usb0: ohci@00600000 {
status = "okay";
num-ports = <2>;
atmel,vbus-gpio = <&pioD 19 1
&pioD 20 1
>;
};
usb1: ehci@00700000 {
status = "okay";
};
};
};
arch/arm/boot/dts/at91sam9g35.dtsi 0 → 100644
浏览文件 @ ae0407e1
/*
* at91sam9g35.dtsi - Device Tree Include file for AT91SAM9G35 SoC
*
* Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
*
* Licensed under GPLv2.
*/
/include/ "at91sam9x5.dtsi"
/ {
model = "Atmel AT91SAM9G35 SoC";
compatible = "atmel, at91sam9g35, atmel,at91sam9x5";
ahb {
apb {
pinctrl@fffff400 {
atmel,mux-mask = <
/* A B C */
0xffffffff 0xffe0399f 0xc000000c /* pioA */
0x000406ff 0x00047e3f 0x00000000 /* pioB */
0xfdffffff 0x00000000 0xb83fffff /* pioC */
0x003fffff 0x003f8000 0x00000000 /* pioD */
>;
};
};
};
};
arch/arm/boot/dts/at91sam9g35ek.dts 0 → 100644
浏览文件 @ ae0407e1
/*
* at91sam9g35ek.dts - Device Tree file for AT91SAM9G35-EK board
*
* Copyright (C) 2012 Atmel,
* 2012 Nicolas Ferre <nicolas.ferre@atmel.com>
*
* Licensed under GPLv2 or later.
*/
/dts-v1/;
/include/ "at91sam9g35.dtsi"
/include/ "at91sam9x5ek.dtsi"
/ {
model = "Atmel AT91SAM9G35-EK";
compatible = "atmel,at91sam9g35ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
};
arch/arm/boot/dts/at91sam9g45.dtsi
浏览文件 @ ae0407e1
......@@ -108,60 +108,151 @@
interrupts = <21 4 0>;
};
pioA: gpio@fffff200 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff200 0x100>;
interrupts = <2 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
pinctrl@fffff200 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "atmel,at91rm9200-pinctrl", "simple-bus";
ranges = <0xfffff200 0xfffff200 0xa00>;
atmel,mux-mask = <
/* A B */
0xffffffff 0xffc003ff /* pioA */
0xffffffff 0x800f8f00 /* pioB */
0xffffffff 0x00000e00 /* pioC */
0xffffffff 0xff0c1381 /* pioD */
0xffffffff 0x81ffff81 /* pioE */
>;
/* shared pinctrl settings */
dbgu {
pinctrl_dbgu: dbgu-0 {
atmel,pins =
<1 12 0x1 0x0 /* PB12 periph A */
1 13 0x1 0x0>; /* PB13 periph A */
};
};
pioB: gpio@fffff400 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff400 0x100>;
interrupts = <3 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
uart0 {
pinctrl_uart0: uart0-0 {
atmel,pins =
<1 19 0x1 0x1 /* PB19 periph A with pullup */
1 18 0x1 0x0>; /* PB18 periph A */
};
pinctrl_uart0_rts_cts: uart0_rts_cts-0 {
atmel,pins =
<1 17 0x2 0x0 /* PB17 periph B */
1 15 0x2 0x0>; /* PB15 periph B */
};
};
pioC: gpio@fffff600 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff600 0x100>;
interrupts = <4 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
uart1 {
pinctrl_uart1: uart1-0 {
atmel,pins =
<1 4 0x1 0x1 /* PB4 periph A with pullup */
1 5 0x1 0x0>; /* PB5 periph A */
};
pinctrl_uart1_rts_cts: uart1_rts_cts-0 {
atmel,pins =
<3 16 0x1 0x0 /* PD16 periph A */
3 17 0x1 0x0>; /* PD17 periph A */
};
};
pioD: gpio@fffff800 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff800 0x100>;
interrupts = <5 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
uart2 {
pinctrl_uart2: uart2-0 {
atmel,pins =
<1 6 0x1 0x1 /* PB6 periph A with pullup */
1 7 0x1 0x0>; /* PB7 periph A */
};
pinctrl_uart2_rts_cts: uart2_rts_cts-0 {
atmel,pins =
<2 9 0x2 0x0 /* PC9 periph B */
2 11 0x2 0x0>; /* PC11 periph B */
};
};
pioE: gpio@fffffa00 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffffa00 0x100>;
interrupts = <5 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
uart3 {
pinctrl_uart3: uart3-0 {
atmel,pins =
<1 8 0x1 0x1 /* PB9 periph A with pullup */
1 9 0x1 0x0>; /* PB8 periph A */
};
pinctrl_uart3_rts_cts: uart3_rts_cts-0 {
atmel,pins =
<0 23 0x2 0x0 /* PA23 periph B */
0 24 0x2 0x0>; /* PA24 periph B */
};
};
nand {
pinctrl_nand: nand-0 {
atmel,pins =
<2 8 0x0 0x1 /* PC8 gpio RDY pin pull_up*/
2 14 0x0 0x1>; /* PC14 gpio enable pin pull_up */
};
};
pioA: gpio@fffff200 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff200 0x200>;
interrupts = <2 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
pioB: gpio@fffff400 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff400 0x200>;
interrupts = <3 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
pioC: gpio@fffff600 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff600 0x200>;
interrupts = <4 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
pioD: gpio@fffff800 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff800 0x200>;
interrupts = <5 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
pioE: gpio@fffffa00 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffffa00 0x200>;
interrupts = <5 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
};
dbgu: serial@ffffee00 {
compatible = "atmel,at91sam9260-usart";
reg = <0xffffee00 0x200>;
interrupts = <1 4 7>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_dbgu>;
status = "disabled";
};
......@@ -171,6 +262,8 @@
interrupts = <7 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart0>;
status = "disabled";
};
......@@ -180,6 +273,8 @@
interrupts = <8 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
status = "disabled";
};
......@@ -189,6 +284,8 @@
interrupts = <9 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
status = "disabled";
};
......@@ -198,6 +295,8 @@
interrupts = <10 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
status = "disabled";
};
......@@ -273,6 +372,8 @@
>;
atmel,nand-addr-offset = <21>;
atmel,nand-cmd-offset = <22>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_nand>;
gpios = <&pioC 8 0
&pioC 14 0
0
......
arch/arm/boot/dts/at91sam9m10g45ek.dts
浏览文件 @ ae0407e1
......@@ -39,6 +39,7 @@
};
usart1: serial@fff90000 {
pinctrl-0 = <&pinctrl_uart0 &pinctrl_uart1_rts_cts>;
status = "okay";
};
......
arch/arm/boot/dts/at91sam9n12.dtsi
浏览文件 @ ae0407e1
......@@ -102,50 +102,150 @@
interrupts = <20 4 0>;
};
pioA: gpio@fffff400 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff400 0x100>;
interrupts = <2 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
pinctrl@fffff400 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "atmel,at91sam9x5-pinctrl", "atmel,at91rm9200-pinctrl", "simple-bus";
ranges = <0xfffff400 0xfffff400 0x800>;
pioB: gpio@fffff600 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff600 0x100>;
interrupts = <2 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
atmel,mux-mask = <
/* A B C */
0xffffffff 0xffe07983 0x00000000 /* pioA */
0x00040000 0x00047e0f 0x00000000 /* pioB */
0xfdffffff 0x07c00000 0xb83fffff /* pioC */
0x003fffff 0x003f8000 0x00000000 /* pioD */
>;
pioC: gpio@fffff800 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff800 0x100>;
interrupts = <3 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
/* shared pinctrl settings */
dbgu {
pinctrl_dbgu: dbgu-0 {
atmel,pins =
<0 9 0x1 0x0 /* PA9 periph A */
0 10 0x1 0x1>; /* PA10 periph with pullup */
};
};
pioD: gpio@fffffa00 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffffa00 0x100>;
interrupts = <3 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
uart0 {
pinctrl_uart0: uart0-0 {
atmel,pins =
<0 1 0x1 0x1 /* PA1 periph A with pullup */
0 0 0x1 0x0>; /* PA0 periph A */
};
pinctrl_uart0_rts_cts: uart0_rts_cts-0 {
atmel,pins =
<0 2 0x1 0x0 /* PA2 periph A */
0 3 0x1 0x0>; /* PA3 periph A */
};
};
uart1 {
pinctrl_uart1: uart1-0 {
atmel,pins =
<0 6 0x1 0x1 /* PA6 periph A with pullup */
0 5 0x1 0x0>; /* PA5 periph A */
};
};
uart2 {
pinctrl_uart2: uart2-0 {
atmel,pins =
<0 8 0x1 0x1 /* PA8 periph A with pullup */
0 7 0x1 0x0>; /* PA7 periph A */
};
pinctrl_uart2_rts_cts: uart2_rts_cts-0 {
atmel,pins =
<1 0 0x2 0x0 /* PB0 periph B */
1 1 0x2 0x0>; /* PB1 periph B */
};
};
uart3 {
pinctrl_uart3: uart3-0 {
atmel,pins =
<2 23 0x2 0x1 /* PC23 periph B with pullup */
2 22 0x2 0x0>; /* PC22 periph B */
};
pinctrl_uart3_rts_cts: uart3_rts_cts-0 {
atmel,pins =
<2 24 0x2 0x0 /* PC24 periph B */
2 25 0x2 0x0>; /* PC25 periph B */
};
};
usart0 {
pinctrl_usart0: usart0-0 {
atmel,pins =
<2 9 0x3 0x1 /* PC9 periph C with pullup */
2 8 0x3 0x0>; /* PC8 periph C */
};
};
usart1 {
pinctrl_usart1: usart1-0 {
atmel,pins =
<2 16 0x3 0x1 /* PC17 periph C with pullup */
2 17 0x3 0x0>; /* PC16 periph C */
};
};
nand {
pinctrl_nand: nand-0 {
atmel,pins =
<3 5 0x0 0x1 /* PD5 gpio RDY pin pull_up*/
3 4 0x0 0x1>; /* PD4 gpio enable pin pull_up */
};
};
pioA: gpio@fffff400 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff400 0x200>;
interrupts = <2 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
pioB: gpio@fffff600 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff600 0x200>;
interrupts = <2 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
pioC: gpio@fffff800 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff800 0x200>;
interrupts = <3 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
pioD: gpio@fffffa00 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffffa00 0x200>;
interrupts = <3 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
};
dbgu: serial@fffff200 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffff200 0x200>;
interrupts = <1 4 7>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_dbgu>;
status = "disabled";
};
......@@ -155,6 +255,8 @@
interrupts = <5 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart0>;
status = "disabled";
};
......@@ -164,6 +266,8 @@
interrupts = <6 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
status = "disabled";
};
......@@ -173,6 +277,8 @@
interrupts = <7 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
status = "disabled";
};
......@@ -182,6 +288,8 @@
interrupts = <8 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
status = "disabled";
};
......@@ -215,6 +323,8 @@
>;
atmel,nand-addr-offset = <21>;
atmel,nand-cmd-offset = <22>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_nand>;
gpios = <&pioD 5 0
&pioD 4 0
0
......
arch/arm/boot/dts/at91sam9x25.dtsi 0 → 100644
浏览文件 @ ae0407e1
/*
* at91sam9x25.dtsi - Device Tree Include file for AT91SAM9X25 SoC
*
* Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
*
* Licensed under GPLv2.
*/
/include/ "at91sam9x5.dtsi"
/ {
model = "Atmel AT91SAM9X25 SoC";
compatible = "atmel, at91sam9x25, atmel,at91sam9x5";
ahb {
apb {
pinctrl@fffff400 {
atmel,mux-mask = <
/* A B C */
0xffffffff 0xffe03fff 0xc000001c /* pioA */
0x0007ffff 0x00047e3f 0x00000000 /* pioB */
0x80000000 0xfffd0000 0xb83fffff /* pioC */
0x003fffff 0x003f8000 0x00000000 /* pioD */
>;
};
};
};
};
arch/arm/boot/dts/at91sam9x25ek.dts 0 → 100644
浏览文件 @ ae0407e1
/*
* at91sam9x25ek.dts - Device Tree file for AT91SAM9X25-EK board
*
* Copyright (C) 2012 Atmel,
* 2012 Nicolas Ferre <nicolas.ferre@atmel.com>
*
* Licensed under GPLv2 or later.
*/
/dts-v1/;
/include/ "at91sam9x25.dtsi"
/include/ "at91sam9x5ek.dtsi"
/ {
model = "Atmel AT91SAM9G25-EK";
compatible = "atmel,at91sam9x25ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
};
arch/arm/boot/dts/at91sam9x35.dtsi 0 → 100644
浏览文件 @ ae0407e1
/*
* at91sam9x35.dtsi - Device Tree Include file for AT91SAM9X35 SoC
*
* Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
*
* Licensed under GPLv2.
*/
/include/ "at91sam9x5.dtsi"
/ {
model = "Atmel AT91SAM9X35 SoC";
compatible = "atmel, at91sam9x35, atmel,at91sam9x5";
ahb {
apb {
pinctrl@fffff400 {
atmel,mux-mask = <
/* A B C */
0xffffffff 0xffe03fff 0xc000000c /* pioA */
0x000406ff 0x00047e3f 0x00000000 /* pioB */
0xfdffffff 0x00000000 0xb83fffff /* pioC */
0x003fffff 0x003f8000 0x00000000 /* pioD */
>;
};
};
};
};
arch/arm/boot/dts/at91sam9x35ek.dts 0 → 100644
浏览文件 @ ae0407e1
/*
* at91sam9x35ek.dts - Device Tree file for AT91SAM9X35-EK board
*
* Copyright (C) 2012 Atmel,
* 2012 Nicolas Ferre <nicolas.ferre@atmel.com>
*
* Licensed under GPLv2 or later.
*/
/dts-v1/;
/include/ "at91sam9x35.dtsi"
/include/ "at91sam9x5ek.dtsi"
/ {
model = "Atmel AT91SAM9X35-EK";
compatible = "atmel,at91sam9x35ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
};
arch/arm/boot/dts/at91sam9x5.dtsi
浏览文件 @ ae0407e1
......@@ -111,50 +111,150 @@
interrupts = <21 4 0>;
};
pioA: gpio@fffff400 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff400 0x100>;
interrupts = <2 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
pinctrl@fffff400 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "atmel,at91sam9x5-pinctrl", "atmel,at91rm9200-pinctrl", "simple-bus";
ranges = <0xfffff400 0xfffff400 0x800>;
/* shared pinctrl settings */
dbgu {
pinctrl_dbgu: dbgu-0 {
atmel,pins =
<0 9 0x1 0x0 /* PA9 periph A */
0 10 0x1 0x1>; /* PA10 periph A with pullup */
};
};
pioB: gpio@fffff600 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff600 0x100>;
interrupts = <2 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
uart0 {
pinctrl_uart0: uart0-0 {
atmel,pins =
<0 0 0x1 0x1 /* PA0 periph A with pullup */
0 1 0x1 0x0>; /* PA1 periph A */
};
pinctrl_uart0_rts_cts: uart0_rts_cts-0 {
atmel,pins =
<0 2 0x1 0x0 /* PA2 periph A */
0 3 0x1 0x0>; /* PA3 periph A */
};
};
pioC: gpio@fffff800 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff800 0x100>;
interrupts = <3 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
uart1 {
pinctrl_uart1: uart1-0 {
atmel,pins =
<0 5 0x1 0x1 /* PA5 periph A with pullup */
0 6 0x1 0x0>; /* PA6 periph A */
};
pinctrl_uart1_rts_cts: uart1_rts_cts-0 {
atmel,pins =
<3 27 0x3 0x0 /* PC27 periph C */
3 28 0x3 0x0>; /* PC28 periph C */
};
};
pioD: gpio@fffffa00 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffffa00 0x100>;
interrupts = <3 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
uart2 {
pinctrl_uart2: uart2-0 {
atmel,pins =
<0 7 0x1 0x1 /* PA7 periph A with pullup */
0 8 0x1 0x0>; /* PA8 periph A */
};
pinctrl_uart2_rts_cts: uart2_rts_cts-0 {
atmel,pins =
<0 0 0x2 0x0 /* PB0 periph B */
0 1 0x2 0x0>; /* PB1 periph B */
};
};
uart3 {
pinctrl_uart3: uart3-0 {
atmel,pins =
<3 23 0x2 0x1 /* PC22 periph B with pullup */
3 23 0x2 0x0>; /* PC23 periph B */
};
pinctrl_uart3_rts_cts: uart3_rts_cts-0 {
atmel,pins =
<3 24 0x2 0x0 /* PC24 periph B */
3 25 0x2 0x0>; /* PC25 periph B */
};
};
usart0 {
pinctrl_usart0: usart0-0 {
atmel,pins =
<3 8 0x3 0x0 /* PC8 periph C */
3 9 0x3 0x1>; /* PC9 periph C with pullup */
};
};
usart1 {
pinctrl_usart1: usart1-0 {
atmel,pins =
<3 16 0x3 0x0 /* PC16 periph C */
3 17 0x3 0x1>; /* PC17 periph C with pullup */
};
};
nand {
pinctrl_nand: nand-0 {
atmel,pins =
<3 4 0x0 0x1 /* PD5 gpio RDY pin pull_up */
3 5 0x0 0x1>; /* PD4 gpio enable pin pull_up */
};
};
pioA: gpio@fffff400 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff400 0x200>;
interrupts = <2 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
pioB: gpio@fffff600 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff600 0x200>;
interrupts = <2 4 1>;
#gpio-cells = <2>;
gpio-controller;
#gpio-lines = <19>;
interrupt-controller;
#interrupt-cells = <2>;
};
pioC: gpio@fffff800 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff800 0x200>;
interrupts = <3 4 1>;
#gpio-cells = <2>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <2>;
};
pioD: gpio@fffffa00 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffffa00 0x200>;
interrupts = <3 4 1>;
#gpio-cells = <2>;
gpio-controller;
#gpio-lines = <22>;
interrupt-controller;
#interrupt-cells = <2>;
};
};
dbgu: serial@fffff200 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffff200 0x200>;
interrupts = <1 4 7>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_dbgu>;
status = "disabled";
};
......@@ -164,6 +264,8 @@
interrupts = <5 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart0>;
status = "disabled";
};
......@@ -173,6 +275,8 @@
interrupts = <6 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
status = "disabled";
};
......@@ -182,6 +286,8 @@
interrupts = <7 4 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
status = "disabled";
};
......@@ -273,6 +379,8 @@
>;
atmel,nand-addr-offset = <21>;
atmel,nand-cmd-offset = <22>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_nand>;
gpios = <&pioD 5 0
&pioD 4 0
0
......
arch/arm/boot/dts/at91sam9x5ek.dtsi 0 → 100644
浏览文件 @ ae0407e1
/*
* at91sam9x5ek.dtsi - Device Tree file for AT91SAM9x5CM Base board
*
* Copyright (C) 2012 Atmel,
* 2012 Nicolas Ferre <nicolas.ferre@atmel.com>
*
* Licensed under GPLv2 or later.
*/
/include/ "at91sam9x5cm.dtsi"
/ {
model = "Atmel AT91SAM9X5-EK";
compatible = "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
chosen {
bootargs = "128M console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=ubifs ubi.mtd=1 root=ubi0:rootfs";
};
ahb {
apb {
dbgu: serial@fffff200 {
status = "okay";
};
usart0: serial@f801c000 {
status = "okay";
};
macb0: ethernet@f802c000 {
phy-mode = "rmii";
status = "okay";
};
i2c0: i2c@f8010000 {
status = "okay";
};
i2c1: i2c@f8014000 {
status = "okay";
};
i2c2: i2c@f8018000 {
status = "okay";
};
};
usb0: ohci@00600000 {
status = "okay";
num-ports = <2>;
atmel,vbus-gpio = <&pioD 19 1
&pioD 20 1
>;
};
usb1: ehci@00700000 {
status = "okay";
};
};
};
arch/arm/configs/at91_dt_defconfig
浏览文件 @ ae0407e1
......@@ -111,6 +111,7 @@ CONFIG_I2C=y
CONFIG_I2C_GPIO=y
CONFIG_SPI=y
CONFIG_SPI_ATMEL=y
CONFIG_PINCTRL_AT91=y
# CONFIG_HWMON is not set
CONFIG_WATCHDOG=y
CONFIG_AT91SAM9X_WATCHDOG=y
......
arch/arm/mach-at91/at91rm9200.c
浏览文件 @ ae0407e1
......@@ -361,10 +361,10 @@ static unsigned int at91rm9200_default_irq_priority[NR_AIC_IRQS] __initdata = {
0 /* Advanced Interrupt Controller (IRQ6) */
};
struct at91_init_soc __initdata at91rm9200_soc = {
AT91_SOC_START(rm9200)
.map_io = at91rm9200_map_io,
.default_irq_priority = at91rm9200_default_irq_priority,
.ioremap_registers = at91rm9200_ioremap_registers,
.register_clocks = at91rm9200_register_clocks,
.init = at91rm9200_initialize,
};
AT91_SOC_END
arch/arm/mach-at91/at91sam9260.c
浏览文件 @ ae0407e1
......@@ -235,6 +235,9 @@ static struct clk_lookup periph_clocks_lookups[] = {
CLKDEV_CON_ID("pioA", &pioA_clk),
CLKDEV_CON_ID("pioB", &pioB_clk),
CLKDEV_CON_ID("pioC", &pioC_clk),
CLKDEV_CON_DEV_ID(NULL, "fffff400.gpio", &pioA_clk),
CLKDEV_CON_DEV_ID(NULL, "fffff600.gpio", &pioB_clk),
CLKDEV_CON_DEV_ID(NULL, "fffff800.gpio", &pioC_clk),
};
static struct clk_lookup usart_clocks_lookups[] = {
......@@ -390,10 +393,10 @@ static unsigned int at91sam9260_default_irq_priority[NR_AIC_IRQS] __initdata = {
0, /* Advanced Interrupt Controller */
};
struct at91_init_soc __initdata at91sam9260_soc = {
AT91_SOC_START(sam9260)
.map_io = at91sam9260_map_io,
.default_irq_priority = at91sam9260_default_irq_priority,
.ioremap_registers = at91sam9260_ioremap_registers,
.register_clocks = at91sam9260_register_clocks,
.init = at91sam9260_initialize,
};
AT91_SOC_END
arch/arm/mach-at91/at91sam9261.c
浏览文件 @ ae0407e1
......@@ -334,10 +334,10 @@ static unsigned int at91sam9261_default_irq_priority[NR_AIC_IRQS] __initdata = {
0, /* Advanced Interrupt Controller */
};
struct at91_init_soc __initdata at91sam9261_soc = {
AT91_SOC_START(sam9261)
.map_io = at91sam9261_map_io,
.default_irq_priority = at91sam9261_default_irq_priority,
.ioremap_registers = at91sam9261_ioremap_registers,
.register_clocks = at91sam9261_register_clocks,
.init = at91sam9261_initialize,
};
AT91_SOC_END
arch/arm/mach-at91/at91sam9263.c
浏览文件 @ ae0407e1
......@@ -212,6 +212,11 @@ static struct clk_lookup periph_clocks_lookups[] = {
CLKDEV_CON_DEV_ID("spi_clk", "fffa4000.spi", &spi0_clk),
CLKDEV_CON_DEV_ID("spi_clk", "fffa8000.spi", &spi1_clk),
CLKDEV_CON_DEV_ID(NULL, "fff88000.i2c", &twi_clk),
CLKDEV_CON_DEV_ID(NULL, "fffff200.gpio", &pioA_clk),
CLKDEV_CON_DEV_ID(NULL, "fffff400.gpio", &pioB_clk),
CLKDEV_CON_DEV_ID(NULL, "fffff600.gpio", &pioCDE_clk),
CLKDEV_CON_DEV_ID(NULL, "fffff800.gpio", &pioCDE_clk),
CLKDEV_CON_DEV_ID(NULL, "fffffa00.gpio", &pioCDE_clk),
};
static struct clk_lookup usart_clocks_lookups[] = {
......@@ -365,10 +370,10 @@ static unsigned int at91sam9263_default_irq_priority[NR_AIC_IRQS] __initdata = {
0, /* Advanced Interrupt Controller (IRQ1) */
};
struct at91_init_soc __initdata at91sam9263_soc = {
AT91_SOC_START(sam9263)
.map_io = at91sam9263_map_io,
.default_irq_priority = at91sam9263_default_irq_priority,
.ioremap_registers = at91sam9263_ioremap_registers,
.register_clocks = at91sam9263_register_clocks,
.init = at91sam9263_initialize,
};
AT91_SOC_END
arch/arm/mach-at91/at91sam9g45.c
浏览文件 @ ae0407e1
......@@ -260,6 +260,12 @@ static struct clk_lookup periph_clocks_lookups[] = {
CLKDEV_CON_DEV_ID(NULL, "fff88000.i2c", &twi1_clk),
/* fake hclk clock */
CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &uhphs_clk),
CLKDEV_CON_DEV_ID(NULL, "fffff200.gpio", &pioA_clk),
CLKDEV_CON_DEV_ID(NULL, "fffff400.gpio", &pioB_clk),
CLKDEV_CON_DEV_ID(NULL, "fffff600.gpio", &pioC_clk),
CLKDEV_CON_DEV_ID(NULL, "fffff800.gpio", &pioDE_clk),
CLKDEV_CON_DEV_ID(NULL, "fffffa00.gpio", &pioDE_clk),
CLKDEV_CON_ID("pioA", &pioA_clk),
CLKDEV_CON_ID("pioB", &pioB_clk),
CLKDEV_CON_ID("pioC", &pioC_clk),
......@@ -409,10 +415,10 @@ static unsigned int at91sam9g45_default_irq_priority[NR_AIC_IRQS] __initdata = {
0, /* Advanced Interrupt Controller (IRQ0) */
};
struct at91_init_soc __initdata at91sam9g45_soc = {
AT91_SOC_START(sam9g45)
.map_io = at91sam9g45_map_io,
.default_irq_priority = at91sam9g45_default_irq_priority,
.ioremap_registers = at91sam9g45_ioremap_registers,
.register_clocks = at91sam9g45_register_clocks,
.init = at91sam9g45_initialize,
};
AT91_SOC_END
arch/arm/mach-at91/at91sam9n12.c
浏览文件 @ ae0407e1
......@@ -171,10 +171,10 @@ static struct clk_lookup periph_clocks_lookups[] = {
CLKDEV_CON_DEV_ID("dma_clk", "ffffec00.dma-controller", &dma_clk),
CLKDEV_CON_DEV_ID(NULL, "f8010000.i2c", &twi0_clk),
CLKDEV_CON_DEV_ID(NULL, "f8014000.i2c", &twi1_clk),
CLKDEV_CON_ID("pioA", &pioAB_clk),
CLKDEV_CON_ID("pioB", &pioAB_clk),
CLKDEV_CON_ID("pioC", &pioCD_clk),
CLKDEV_CON_ID("pioD", &pioCD_clk),
CLKDEV_CON_DEV_ID(NULL, "fffff400.gpio", &pioAB_clk),
CLKDEV_CON_DEV_ID(NULL, "fffff600.gpio", &pioAB_clk),
CLKDEV_CON_DEV_ID(NULL, "fffff800.gpio", &pioCD_clk),
CLKDEV_CON_DEV_ID(NULL, "fffffa00.gpio", &pioCD_clk),
/* additional fake clock for macb_hclk */
CLKDEV_CON_DEV_ID("hclk", "500000.ohci", &uhp_clk),
CLKDEV_CON_DEV_ID("ohci_clk", "500000.ohci", &uhp_clk),
......@@ -223,13 +223,10 @@ static void __init at91sam9n12_map_io(void)
void __init at91sam9n12_initialize(void)
{
at91_extern_irq = (1 << AT91SAM9N12_ID_IRQ0);
/* Register GPIO subsystem (using DT) */
at91_gpio_init(NULL, 0);
}
struct at91_init_soc __initdata at91sam9n12_soc = {
AT91_SOC_START(sam9n12)
.map_io = at91sam9n12_map_io,
.register_clocks = at91sam9n12_register_clocks,
.init = at91sam9n12_initialize,
};
AT91_SOC_END
arch/arm/mach-at91/at91sam9rl.c
浏览文件 @ ae0407e1
......@@ -338,10 +338,10 @@ static unsigned int at91sam9rl_default_irq_priority[NR_AIC_IRQS] __initdata = {
0, /* Advanced Interrupt Controller */
};
struct at91_init_soc __initdata at91sam9rl_soc = {
AT91_SOC_START(sam9rl)
.map_io = at91sam9rl_map_io,
.default_irq_priority = at91sam9rl_default_irq_priority,
.ioremap_registers = at91sam9rl_ioremap_registers,
.register_clocks = at91sam9rl_register_clocks,
.init = at91sam9rl_initialize,
};
AT91_SOC_END
arch/arm/mach-at91/at91sam9x5.c
浏览文件 @ ae0407e1
......@@ -234,10 +234,10 @@ static struct clk_lookup periph_clocks_lookups[] = {
CLKDEV_CON_DEV_ID(NULL, "f8010000.i2c", &twi0_clk),
CLKDEV_CON_DEV_ID(NULL, "f8014000.i2c", &twi1_clk),
CLKDEV_CON_DEV_ID(NULL, "f8018000.i2c", &twi2_clk),
CLKDEV_CON_ID("pioA", &pioAB_clk),
CLKDEV_CON_ID("pioB", &pioAB_clk),
CLKDEV_CON_ID("pioC", &pioCD_clk),
CLKDEV_CON_ID("pioD", &pioCD_clk),
CLKDEV_CON_DEV_ID(NULL, "fffff400.gpio", &pioAB_clk),
CLKDEV_CON_DEV_ID(NULL, "fffff600.gpio", &pioAB_clk),
CLKDEV_CON_DEV_ID(NULL, "fffff800.gpio", &pioCD_clk),
CLKDEV_CON_DEV_ID(NULL, "fffffa00.gpio", &pioCD_clk),
/* additional fake clock for macb_hclk */
CLKDEV_CON_DEV_ID("hclk", "f802c000.ethernet", &macb0_clk),
CLKDEV_CON_DEV_ID("hclk", "f8030000.ethernet", &macb1_clk),
......@@ -313,18 +313,11 @@ static void __init at91sam9x5_map_io(void)
at91_init_sram(0, AT91SAM9X5_SRAM_BASE, AT91SAM9X5_SRAM_SIZE);
}
void __init at91sam9x5_initialize(void)
{
/* Register GPIO subsystem (using DT) */
at91_gpio_init(NULL, 0);
}
/* --------------------------------------------------------------------
* Interrupt initialization
* -------------------------------------------------------------------- */
struct at91_init_soc __initdata at91sam9x5_soc = {
AT91_SOC_START(sam9x5)
.map_io = at91sam9x5_map_io,
.register_clocks = at91sam9x5_register_clocks,
.init = at91sam9x5_initialize,
};
AT91_SOC_END
arch/arm/mach-at91/board-dt.c
浏览文件 @ ae0407e1
......@@ -30,8 +30,6 @@
static const struct of_device_id irq_of_match[] __initconst = {
{ .compatible = "atmel,at91rm9200-aic", .data = at91_aic_of_init },
{ .compatible = "atmel,at91rm9200-gpio", .data = at91_gpio_of_irq_setup },
{ .compatible = "atmel,at91sam9x5-gpio", .data = at91_gpio_of_irq_setup },
{ /*sentinel*/ }
};
......
arch/arm/mach-at91/gpio.c
浏览文件 @ ae0407e1
......@@ -23,8 +23,6 @@
#include <linux/io.h>
#include <linux/irqdomain.h>
#include <linux/of_address.h>
#include <linux/of_irq.h>
#include <linux/of_gpio.h>
#include <asm/mach/irq.h>
......@@ -33,6 +31,8 @@
#include "generic.h"
#define MAX_NB_GPIO_PER_BANK 32
struct at91_gpio_chip {
struct gpio_chip chip;
struct at91_gpio_chip *next; /* Bank sharing same clock */
......@@ -46,6 +46,7 @@ struct at91_gpio_chip {
#define to_at91_gpio_chip(c) container_of(c, struct at91_gpio_chip, chip)
static int at91_gpiolib_request(struct gpio_chip *chip, unsigned offset);
static void at91_gpiolib_dbg_show(struct seq_file *s, struct gpio_chip *chip);
static void at91_gpiolib_set(struct gpio_chip *chip, unsigned offset, int val);
static int at91_gpiolib_get(struct gpio_chip *chip, unsigned offset);
......@@ -55,26 +56,27 @@ static int at91_gpiolib_direction_input(struct gpio_chip *chip,
unsigned offset);
static int at91_gpiolib_to_irq(struct gpio_chip *chip, unsigned offset);
#define AT91_GPIO_CHIP(name, nr_gpio) \
#define AT91_GPIO_CHIP(name) \
{ \
.chip = { \
.label = name, \
.request = at91_gpiolib_request, \
.direction_input = at91_gpiolib_direction_input, \
.direction_output = at91_gpiolib_direction_output, \
.get = at91_gpiolib_get, \
.set = at91_gpiolib_set, \
.dbg_show = at91_gpiolib_dbg_show, \
.to_irq = at91_gpiolib_to_irq, \
.ngpio = nr_gpio, \
.ngpio = MAX_NB_GPIO_PER_BANK, \
}, \
}
static struct at91_gpio_chip gpio_chip[] = {
AT91_GPIO_CHIP("pioA", 32),
AT91_GPIO_CHIP("pioB", 32),
AT91_GPIO_CHIP("pioC", 32),
AT91_GPIO_CHIP("pioD", 32),
AT91_GPIO_CHIP("pioE", 32),
AT91_GPIO_CHIP("pioA"),
AT91_GPIO_CHIP("pioB"),
AT91_GPIO_CHIP("pioC"),
AT91_GPIO_CHIP("pioD"),
AT91_GPIO_CHIP("pioE"),
};
static int gpio_banks;
......@@ -89,7 +91,7 @@ static unsigned long at91_gpio_caps;
static inline void __iomem *pin_to_controller(unsigned pin)
{
pin /= 32;
pin /= MAX_NB_GPIO_PER_BANK;
if (likely(pin < gpio_banks))
return gpio_chip[pin].regbase;
......@@ -98,7 +100,7 @@ static inline void __iomem *pin_to_controller(unsigned pin)
static inline unsigned pin_to_mask(unsigned pin)
{
return 1 << (pin % 32);
return 1 << (pin % MAX_NB_GPIO_PER_BANK);
}
......@@ -713,80 +715,6 @@ postcore_initcall(at91_gpio_debugfs_init);
*/
static struct lock_class_key gpio_lock_class;
#if defined(CONFIG_OF)
static int at91_gpio_irq_map(struct irq_domain *h, unsigned int virq,
irq_hw_number_t hw)
{
struct at91_gpio_chip *at91_gpio = h->host_data;
irq_set_lockdep_class(virq, &gpio_lock_class);
/*
* Can use the "simple" and not "edge" handler since it's
* shorter, and the AIC handles interrupts sanely.
*/
irq_set_chip_and_handler(virq, &gpio_irqchip,
handle_simple_irq);
set_irq_flags(virq, IRQF_VALID);
irq_set_chip_data(virq, at91_gpio);
return 0;
}
static struct irq_domain_ops at91_gpio_ops = {
.map = at91_gpio_irq_map,
.xlate = irq_domain_xlate_twocell,
};
int __init at91_gpio_of_irq_setup(struct device_node *node,
struct device_node *parent)
{
struct at91_gpio_chip *prev = NULL;
int alias_idx = of_alias_get_id(node, "gpio");
struct at91_gpio_chip *at91_gpio = &gpio_chip[alias_idx];
/* Setup proper .irq_set_type function */
if (has_pio3())
gpio_irqchip.irq_set_type = alt_gpio_irq_type;
else
gpio_irqchip.irq_set_type = gpio_irq_type;
/* Disable irqs of this PIO controller */
__raw_writel(~0, at91_gpio->regbase + PIO_IDR);
/* Setup irq domain */
at91_gpio->domain = irq_domain_add_linear(node, at91_gpio->chip.ngpio,
&at91_gpio_ops, at91_gpio);
if (!at91_gpio->domain)
panic("at91_gpio.%d: couldn't allocate irq domain (DT).\n",
at91_gpio->pioc_idx);
/* Setup chained handler */
if (at91_gpio->pioc_idx)
prev = &gpio_chip[at91_gpio->pioc_idx - 1];
/* The toplevel handler handles one bank of GPIOs, except
* on some SoC it can handles up to three...
* We only set up the handler for the first of the list.
*/
if (prev && prev->next == at91_gpio)
return 0;
at91_gpio->pioc_virq = irq_create_mapping(irq_find_host(parent),
at91_gpio->pioc_hwirq);
irq_set_chip_data(at91_gpio->pioc_virq, at91_gpio);
irq_set_chained_handler(at91_gpio->pioc_virq, gpio_irq_handler);
return 0;
}
#else
int __init at91_gpio_of_irq_setup(struct device_node *node,
struct device_node *parent)
{
return -EINVAL;
}
#endif
/*
* irqdomain initialization: pile up irqdomains on top of AIC range
*/
......@@ -862,6 +790,16 @@ void __init at91_gpio_irq_setup(void)
}
/* gpiolib support */
static int at91_gpiolib_request(struct gpio_chip *chip, unsigned offset)
{
struct at91_gpio_chip *at91_gpio = to_at91_gpio_chip(chip);
void __iomem *pio = at91_gpio->regbase;
unsigned mask = 1 << offset;
__raw_writel(mask, pio + PIO_PER);
return 0;
}
static int at91_gpiolib_direction_input(struct gpio_chip *chip,
unsigned offset)
{
......@@ -975,81 +913,11 @@ static int __init at91_gpio_setup_clk(int idx)
return -EINVAL;
}
#ifdef CONFIG_OF_GPIO
static void __init of_at91_gpio_init_one(struct device_node *np)
{
int alias_idx;
struct at91_gpio_chip *at91_gpio;
if (!np)
return;
alias_idx = of_alias_get_id(np, "gpio");
if (alias_idx >= MAX_GPIO_BANKS) {
pr_err("at91_gpio, failed alias idx(%d) > MAX_GPIO_BANKS(%d), ignoring.\n",
alias_idx, MAX_GPIO_BANKS);
return;
}
at91_gpio = &gpio_chip[alias_idx];
at91_gpio->chip.base = alias_idx * at91_gpio->chip.ngpio;
at91_gpio->regbase = of_iomap(np, 0);
if (!at91_gpio->regbase) {
pr_err("at91_gpio.%d, failed to map registers, ignoring.\n",
alias_idx);
return;
}
/* Get the interrupts property */
if (of_property_read_u32(np, "interrupts", &at91_gpio->pioc_hwirq)) {
pr_err("at91_gpio.%d, failed to get interrupts property, ignoring.\n",
alias_idx);
goto ioremap_err;
}
/* Get capabilities from compatibility property */
if (of_device_is_compatible(np, "atmel,at91sam9x5-gpio"))
at91_gpio_caps |= AT91_GPIO_CAP_PIO3;
/* Setup clock */
if (at91_gpio_setup_clk(alias_idx))
goto ioremap_err;
at91_gpio->chip.of_node = np;
gpio_banks = max(gpio_banks, alias_idx + 1);
at91_gpio->pioc_idx = alias_idx;
return;
ioremap_err:
iounmap(at91_gpio->regbase);
}
static int __init of_at91_gpio_init(void)
{
struct device_node *np = NULL;
/*
* This isn't ideal, but it gets things hooked up until this
* driver is converted into a platform_device
*/
for_each_compatible_node(np, NULL, "atmel,at91rm9200-gpio")
of_at91_gpio_init_one(np);
return gpio_banks > 0 ? 0 : -EINVAL;
}
#else
static int __init of_at91_gpio_init(void)
{
return -EINVAL;
}
#endif
static void __init at91_gpio_init_one(int idx, u32 regbase, int pioc_hwirq)
{
struct at91_gpio_chip *at91_gpio = &gpio_chip[idx];
at91_gpio->chip.base = idx * at91_gpio->chip.ngpio;
at91_gpio->chip.base = idx * MAX_NB_GPIO_PER_BANK;
at91_gpio->pioc_hwirq = pioc_hwirq;
at91_gpio->pioc_idx = idx;
......@@ -1079,11 +947,11 @@ void __init at91_gpio_init(struct at91_gpio_bank *data, int nr_banks)
BUG_ON(nr_banks > MAX_GPIO_BANKS);
if (of_at91_gpio_init() < 0) {
/* No GPIO controller found in device tree */
for (i = 0; i < nr_banks; i++)
at91_gpio_init_one(i, data[i].regbase, data[i].id);
}
if (of_have_populated_dt())
return;
for (i = 0; i < nr_banks; i++)
at91_gpio_init_one(i, data[i].regbase, data[i].id);
for (i = 0; i < gpio_banks; i++) {
at91_gpio = &gpio_chip[i];
......
arch/arm/mach-at91/setup.c
浏览文件 @ ae0407e1
......@@ -10,6 +10,7 @@
#include <linux/mm.h>
#include <linux/pm.h>
#include <linux/of_address.h>
#include <linux/pinctrl/machine.h>
#include <asm/system_misc.h>
#include <asm/mach/map.h>
......@@ -448,7 +449,8 @@ void __init at91_dt_initialize(void)
/* Register the processor-specific clocks */
at91_boot_soc.register_clocks();
at91_boot_soc.init();
if (at91_boot_soc.init)
at91_boot_soc.init();
}
#endif
......@@ -463,4 +465,6 @@ void __init at91_initialize(unsigned long main_clock)
at91_boot_soc.register_clocks();
at91_boot_soc.init();
pinctrl_provide_dummies();
}
arch/arm/mach-at91/soc.h
浏览文件 @ ae0407e1
......@@ -5,6 +5,7 @@
*/
struct at91_init_soc {
int builtin;
unsigned int *default_irq_priority;
void (*map_io)(void);
void (*ioremap_registers)(void);
......@@ -22,9 +23,18 @@ extern struct at91_init_soc at91sam9rl_soc;
extern struct at91_init_soc at91sam9x5_soc;
extern struct at91_init_soc at91sam9n12_soc;
#define AT91_SOC_START(_name) \
struct at91_init_soc __initdata at91##_name##_soc \
__used \
= { \
.builtin = 1, \
#define AT91_SOC_END \
};
static inline int at91_soc_is_enabled(void)
{
return at91_boot_soc.init != NULL;
return at91_boot_soc.builtin;
}
#if !defined(CONFIG_SOC_AT91RM9200)
......
drivers/mtd/nand/atmel_nand.c
浏览文件 @ ae0407e1
......@@ -41,6 +41,7 @@
#include <linux/gpio.h>
#include <linux/io.h>
#include <linux/platform_data/atmel.h>
#include <linux/pinctrl/consumer.h>
#include <mach/cpu.h>
......@@ -1370,6 +1371,7 @@ static int __init atmel_nand_probe(struct platform_device *pdev)
struct resource *mem;
struct mtd_part_parser_data ppdata = {};
int res;
struct pinctrl *pinctrl;
mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!mem) {
......@@ -1414,6 +1416,13 @@ static int __init atmel_nand_probe(struct platform_device *pdev)
nand_chip->IO_ADDR_W = host->io_base;
nand_chip->cmd_ctrl = atmel_nand_cmd_ctrl;
pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
if (IS_ERR(pinctrl)) {
dev_err(host->dev, "Failed to request pinctrl\n");
res = PTR_ERR(pinctrl);
goto err_ecc_ioremap;
}
if (gpio_is_valid(host->board.rdy_pin)) {
res = gpio_request(host->board.rdy_pin, "nand_rdy");
if (res < 0) {
......
drivers/pinctrl/Kconfig
浏览文件 @ ae0407e1
......@@ -26,6 +26,15 @@ config DEBUG_PINCTRL
help
Say Y here to add some extra checks and diagnostics to PINCTRL calls.
config PINCTRL_AT91
bool "AT91 pinctrl driver"
depends on OF
depends on ARCH_AT91
select PINMUX
select PINCONF
help
Say Y here to enable the at91 pinctrl driver
config PINCTRL_BCM2835
bool
select PINMUX
......
drivers/pinctrl/Makefile
浏览文件 @ ae0407e1
......@@ -9,6 +9,7 @@ ifeq ($(CONFIG_OF),y)
obj-$(CONFIG_PINCTRL) += devicetree.o
endif
obj-$(CONFIG_GENERIC_PINCONF) += pinconf-generic.o
obj-$(CONFIG_PINCTRL_AT91) += pinctrl-at91.o
obj-$(CONFIG_PINCTRL_BCM2835) += pinctrl-bcm2835.o
obj-$(CONFIG_PINCTRL_IMX) += pinctrl-imx.o
obj-$(CONFIG_PINCTRL_IMX35) += pinctrl-imx35.o
......
drivers/pinctrl/pinctrl-at91.c 0 → 100644
浏览文件 @ ae0407e1
此差异已折叠。
drivers/tty/serial/atmel_serial.c
浏览文件 @ ae0407e1
......@@ -39,6 +39,7 @@
#include <linux/atmel_pdc.h>
#include <linux/atmel_serial.h>
#include <linux/uaccess.h>
#include <linux/pinctrl/consumer.h>
#include <asm/io.h>
#include <asm/ioctls.h>
......@@ -1773,6 +1774,7 @@ static int __devinit atmel_serial_probe(struct platform_device *pdev)
struct atmel_uart_data *pdata = pdev->dev.platform_data;
void *data;
int ret = -ENODEV;
struct pinctrl *pinctrl;
BUILD_BUG_ON(ATMEL_SERIAL_RINGSIZE & (ATMEL_SERIAL_RINGSIZE - 1));
......@@ -1805,6 +1807,12 @@ static int __devinit atmel_serial_probe(struct platform_device *pdev)
atmel_init_port(port, pdev);
pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
if (IS_ERR(pinctrl)) {
ret = PTR_ERR(pinctrl);
goto err;
}
if (!atmel_use_dma_rx(&port->uart)) {
ret = -ENOMEM;
data = kmalloc(sizeof(struct atmel_uart_char)
......
Markdown is supported
0% 或 .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑！
想要评论请 注册 或