提交 a07d499b 编写于 作者: T Tejun Heo 提交者: Jeff Garzik

libata: add @spd_limit to sata_down_spd_limit()

Add @spd_limit to sata_down_spd_limit() so that the caller can specify
the SPD limit it wants.  This parameter doesn't get in the way even
when it's too low.  The closest possible limit is applied.
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
上级 99cf610a
......@@ -2777,7 +2777,7 @@ int ata_bus_probe(struct ata_port *ap)
/* This is the last chance, better to slow
* down than lose it.
*/
sata_down_spd_limit(&ap->link);
sata_down_spd_limit(&ap->link, 0);
ata_down_xfermask_limit(dev, ATA_DNXFER_PIO);
}
}
......@@ -2873,21 +2873,27 @@ void ata_port_disable(struct ata_port *ap)
/**
* sata_down_spd_limit - adjust SATA spd limit downward
* @link: Link to adjust SATA spd limit for
* @spd_limit: Additional limit
*
* Adjust SATA spd limit of @link downward. Note that this
* function only adjusts the limit. The change must be applied
* using sata_set_spd().
*
* If @spd_limit is non-zero, the speed is limited to equal to or
* lower than @spd_limit if such speed is supported. If
* @spd_limit is slower than any supported speed, only the lowest
* supported speed is allowed.
*
* LOCKING:
* Inherited from caller.
*
* RETURNS:
* 0 on success, negative errno on failure
*/
int sata_down_spd_limit(struct ata_link *link)
int sata_down_spd_limit(struct ata_link *link, u32 spd_limit)
{
u32 sstatus, spd, mask;
int rc, highbit;
int rc, bit;
if (!sata_scr_valid(link))
return -EOPNOTSUPP;
......@@ -2906,8 +2912,8 @@ int sata_down_spd_limit(struct ata_link *link)
return -EINVAL;
/* unconditionally mask off the highest bit */
highbit = fls(mask) - 1;
mask &= ~(1 << highbit);
bit = fls(mask) - 1;
mask &= ~(1 << bit);
/* Mask off all speeds higher than or equal to the current
* one. Force 1.5Gbps if current SPD is not available.
......@@ -2921,6 +2927,15 @@ int sata_down_spd_limit(struct ata_link *link)
if (!mask)
return -EINVAL;
if (spd_limit) {
if (mask & ((1 << spd_limit) - 1))
mask &= (1 << spd_limit) - 1;
else {
bit = ffs(mask) - 1;
mask = 1 << bit;
}
}
link->sata_spd_limit = mask;
ata_link_printk(link, KERN_WARNING, "limiting SATA link speed to %s\n",
......
......@@ -1875,7 +1875,7 @@ static unsigned int ata_eh_speed_down(struct ata_device *dev,
/* speed down? */
if (verdict & ATA_EH_SPDN_SPEED_DOWN) {
/* speed down SATA link speed if possible */
if (sata_down_spd_limit(link) == 0) {
if (sata_down_spd_limit(link, 0) == 0) {
action |= ATA_EH_RESET;
goto done;
}
......@@ -2627,11 +2627,11 @@ int ata_eh_reset(struct ata_link *link, int classify,
}
if (try == max_tries - 1) {
sata_down_spd_limit(link);
sata_down_spd_limit(link, 0);
if (slave)
sata_down_spd_limit(slave);
sata_down_spd_limit(slave, 0);
} else if (rc == -EPIPE)
sata_down_spd_limit(failed_link);
sata_down_spd_limit(failed_link, 0);
if (hardreset)
reset = hardreset;
......@@ -3011,7 +3011,7 @@ static int ata_eh_handle_dev_fail(struct ata_device *dev, int err)
/* This is the last chance, better to slow
* down than lose it.
*/
sata_down_spd_limit(ata_dev_phys_link(dev));
sata_down_spd_limit(ata_dev_phys_link(dev), 0);
if (dev->pio_mode > XFER_PIO_0)
ata_down_xfermask_limit(dev, ATA_DNXFER_PIO);
}
......
......@@ -729,7 +729,7 @@ static int sata_pmp_eh_recover_pmp(struct ata_port *ap,
if (tries) {
/* consecutive revalidation failures? speed down */
if (reval_failed)
sata_down_spd_limit(link);
sata_down_spd_limit(link, 0);
else
reval_failed = 1;
......
......@@ -99,7 +99,7 @@ extern int ata_dev_reread_id(struct ata_device *dev, unsigned int readid_flags);
extern int ata_dev_revalidate(struct ata_device *dev, unsigned int new_class,
unsigned int readid_flags);
extern int ata_dev_configure(struct ata_device *dev);
extern int sata_down_spd_limit(struct ata_link *link);
extern int sata_down_spd_limit(struct ata_link *link, u32 spd_limit);
extern int ata_down_xfermask_limit(struct ata_device *dev, unsigned int sel);
extern void ata_sg_clean(struct ata_queued_cmd *qc);
extern void ata_qc_free(struct ata_queued_cmd *qc);
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册