net: ks8851: Added support for half-duplex SPI

In original driver was implemented support for half-
and full-duplex modes, but it was not enabled. Instead
of it ks8851_rx_1msg method always returns "true" that
means "full-duplex" mode.

This patch replaces hard-coded functionality with
flexible solution that supports both SPI modes.
Signed-off-by: NSergey Shcherbakov <shchers@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/ethernet/micrel/ks8851.c

@@ -211,25 +211,6 @@ static void ks8851_wrreg8(struct ks8851_net *ks, unsigned reg, unsigned val)
 		netdev_err(ks->netdev, "spi_sync() failed\n");
 }
 
-/**
- * ks8851_rx_1msg - select whether to use one or two messages for spi read
- * @ks: The device structure
- *
- * Return whether to generate a single message with a tx and rx buffer
- * supplied to spi_sync(), or alternatively send the tx and rx buffers
- * as separate messages.
- *
- * Depending on the hardware in use, a single message may be more efficient
- * on interrupts or work done by the driver.
- *
- * This currently always returns true until we add some per-device data passed
- * from the platform code to specify which mode is better.
- */
-static inline bool ks8851_rx_1msg(struct ks8851_net *ks)
-{
-	return true;
-}
-
 /**
  * ks8851_rdreg - issue read register command and return the data
  * @ks: The device state
@@ -251,14 +232,7 @@ static void ks8851_rdreg(struct ks8851_net *ks, unsigned op,
 
 	txb[0] = cpu_to_le16(op | KS_SPIOP_RD);
 
-	if (ks8851_rx_1msg(ks)) {
-		msg = &ks->spi_msg1;
-		xfer = &ks->spi_xfer1;
-
-		xfer->tx_buf = txb;
-		xfer->rx_buf = trx;
-		xfer->len = rxl + 2;
-	} else {
+	if (ks->spidev->master->flags & SPI_MASTER_HALF_DUPLEX) {
 		msg = &ks->spi_msg2;
 		xfer = ks->spi_xfer2;
 
@@ -270,15 +244,22 @@ static void ks8851_rdreg(struct ks8851_net *ks, unsigned op,
 		xfer->tx_buf = NULL;
 		xfer->rx_buf = trx;
 		xfer->len = rxl;
+	} else {
+		msg = &ks->spi_msg1;
+		xfer = &ks->spi_xfer1;
+
+		xfer->tx_buf = txb;
+		xfer->rx_buf = trx;
+		xfer->len = rxl + 2;
 	}
 
 	ret = spi_sync(ks->spidev, msg);
 	if (ret < 0)
 		netdev_err(ks->netdev, "read: spi_sync() failed\n");
-	else if (ks8851_rx_1msg(ks))
-		memcpy(rxb, trx + 2, rxl);
-	else
+	else if (ks->spidev->master->flags & SPI_MASTER_HALF_DUPLEX)
 		memcpy(rxb, trx, rxl);
+	else
+		memcpy(rxb, trx + 2, rxl);
 }
 
 /**