Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input

Pull input updates from Dmitry Torokhov:
 "An update to the Goodix touchscreen driver to enable it work properly
  on various Bay Trail and Cherry Trail devices, and a few other
  assorted changes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (26 commits)
  Input: update SPDX tag for input-event-codes.h
  Input: i8042 - add Acer Aspire 5738z to nomux list
  Input: goodix - fix compilation when ACPI support is disabled
  dt-bindings: touchscreen: Convert edt-ft5x06 to json-schema
  Input: of_touchscreen - explicitly choose axis
  Input: goodix - support gt9147 touchpanel
  dt-bindings: touchscreen: goodix: support of gt9147
  Input: goodix - add support for Goodix GT917S
  Input: goodix - use string-based chip ID
  dt-bindings: input: touchscreen: add compatible string for Goodix GT917S
  Input: goodix - add support for more then one touch-key
  Input: goodix - fix spurious key release events
  Input: goodix - try to reset the controller if the i2c-test fails
  Input: goodix - restore config on resume if necessary
  Input: goodix - make goodix_send_cfg() take a raw buffer as argument
  Input: goodix - add minimum firmware size check
  Input: goodix - save a copy of the config from goodix_read_config()
  Input: goodix - move defines to above struct goodix_ts_data declaration
  Input: goodix - add support for controlling the IRQ pin through ACPI methods
  Input: goodix - add support for getting IRQ + reset GPIOs on Bay Trail devices
  ...

Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt

-FocalTech EDT-FT5x06 Polytouch driver
-=====================================
-
-There are 5 variants of the chip for various touch panel sizes
-FT5206GE1  2.8" .. 3.8"
-FT5306DE4  4.3" .. 7"
-FT5406EE8  7"   .. 8.9"
-FT5506EEG  7"   .. 8.9"
-FT5726NEI  5.7” .. 11.6"
-
-The software interface is identical for all those chips, so that
-currently there is no need for the driver to distinguish between the
-different chips. Nevertheless distinct compatible strings are used so
-that a distinction can be added if necessary without changing the DT
-bindings.
-
-
-Required properties:
- - compatible:  "edt,edt-ft5206"
-           or:  "edt,edt-ft5306"
-           or:  "edt,edt-ft5406"
-           or:  "edt,edt-ft5506"
-           or:  "evervision,ev-ft5726"
-           or:  "focaltech,ft6236"
-
- - reg:         I2C slave address of the chip (0x38)
- - interrupts:       interrupt specification for the touchdetect
-                     interrupt
-
-Optional properties:
- - reset-gpios: GPIO specification for the RESET input
- - wake-gpios:  GPIO specification for the WAKE input
- - vcc-supply:  Regulator that supplies the touchscreen
-
- - pinctrl-names: should be "default"
- - pinctrl-0:   a phandle pointing to the pin settings for the
-                control gpios
-
- - wakeup-source: If present the device will act as wakeup-source
-
- - threshold:   allows setting the "click"-threshold in the range
-                from 0 to 80.
-
- - gain:        allows setting the sensitivity in the range from 0 to
-                31. Note that lower values indicate higher
-                sensitivity.
-
- - offset:      allows setting the edge compensation in the range from
-                0 to 31.
-
- - offset-x:    Same as offset, but applies only to the horizontal position.
-                Range from 0 to 80, only supported by evervision,ev-ft5726
-                devices.
-
- - offset-y:    Same as offset, but applies only to the vertical position.
-                Range from 0 to 80, only supported by evervision,ev-ft5726
-                devices.
-
- - touchscreen-size-x	   : See touchscreen.txt
- - touchscreen-size-y	   : See touchscreen.txt
- - touchscreen-fuzz-x      : See touchscreen.txt
- - touchscreen-fuzz-y      : See touchscreen.txt
- - touchscreen-inverted-x  : See touchscreen.txt
- - touchscreen-inverted-y  : See touchscreen.txt
- - touchscreen-swapped-x-y : See touchscreen.txt
-
-Example:
-	polytouch: edt-ft5x06@38 {
-		compatible = "edt,edt-ft5406", "edt,edt-ft5x06";
-		reg = <0x38>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&edt_ft5x06_pins>;
-		interrupt-parent = <&gpio2>;
-		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
-		reset-gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
-		wake-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>;
-	};

Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.yaml

+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/input/touchscreen/edt-ft5x06.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: FocalTech EDT-FT5x06 Polytouch Bindings
+
+description: |
+             There are 5 variants of the chip for various touch panel sizes
+              FT5206GE1  2.8" .. 3.8"
+              FT5306DE4  4.3" .. 7"
+              FT5406EE8  7"   .. 8.9"
+              FT5506EEG  7"   .. 8.9"
+              FT5726NEI  5.7” .. 11.6"
+
+maintainers:
+  - Dmitry Torokhov <dmitry.torokhov@gmail.com>
+
+allOf:
+  - $ref: touchscreen.yaml#
+  - if:
+     properties:
+       compatible:
+         contains:
+           enum:
+             - evervision,ev-ft5726
+
+    then:
+      properties:
+        offset-x: true
+        offset-y: true
+
+properties:
+  compatible:
+    enum:
+      - edt,edt-ft5206
+      - edt,edt-ft5306
+      - edt,edt-ft5406
+      - edt,edt-ft5506
+      - evervision,ev-ft5726
+      - focaltech,ft6236
+
+  reg:
+    const: 0x38
+
+  interrupts:
+    maxItems: 1
+
+  reset-gpios:
+    maxItems: 1
+
+  wake-gpios:
+    maxItems: 1
+
+  wakeup-source: true
+
+  vcc-supply:
+    maxItems: 1
+
+  gain:
+    description: Allows setting the sensitivity in the range from 0 to 31.
+                 Note that lower values indicate higher sensitivity.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - minimum: 0
+      - maximum: 31
+
+  offset:
+    description: Allows setting the edge compensation in the range from 0 to 31.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - minimum: 0
+      - maximum: 31
+
+  offset-x:
+    description: Same as offset, but applies only to the horizontal position.
+                 Range from 0 to 80, only supported by evervision,ev-ft5726 devices.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - minimum: 0
+      - maximum: 80
+
+  offset-y:
+    description: Same as offset, but applies only to the vertical position.
+                 Range from 0 to 80, only supported by evervision,ev-ft5726 devices.
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - minimum: 0
+      - maximum: 80
+
+  touchscreen-size-x: true
+  touchscreen-size-y: true
+  touchscreen-fuzz-x: true
+  touchscreen-fuzz-y: true
+  touchscreen-inverted-x: true
+  touchscreen-inverted-y: true
+  touchscreen-swapped-x-y: true
+  interrupt-controller: true
+
+additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    i2c@00000000 {
+      #address-cells = <1>;
+      #size-cells = <0>;
+      edt-ft5x06@38 {
+        compatible = "edt,edt-ft5406";
+        reg = <0x38>;
+        interrupt-parent = <&gpio2>;
+        interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+        reset-gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
+        wake-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>;
+      };
+    };
+
+...

Documentation/devicetree/bindings/input/touchscreen/goodix.yaml

@@ -21,6 +21,8 @@ properties:
       - goodix,gt911
       - goodix,gt9110
       - goodix,gt912
+      - goodix,gt9147
+      - goodix,gt917s
       - goodix,gt927
       - goodix,gt9271
       - goodix,gt928

drivers/input/serio/i8042-x86ia64io.h

@@ -530,6 +530,17 @@ static const struct dmi_system_id __initconst i8042_dmi_nomux_table[] = {
 			DMI_MATCH(DMI_PRODUCT_VERSION, "Lenovo LaVie Z"),
 		},
 	},
+	{
+		/*
+		 * Acer Aspire 5738z
+		 * Touchpad stops working in mux mode when dis- + re-enabled
+		 * with the touchpad enable/disable toggle hotkey
+		 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "Aspire 5738"),
+		},
+	},
 	{ }
 };
 

drivers/input/touchscreen/elants_i2c.c

@@ -1309,6 +1309,7 @@ static int elants_i2c_probe(struct i2c_client *client,
 	input_set_abs_params(ts->input, ABS_MT_PRESSURE, 0, 255, 0, 0);
 	input_abs_set_res(ts->input, ABS_MT_POSITION_X, ts->x_res);
 	input_abs_set_res(ts->input, ABS_MT_POSITION_Y, ts->y_res);
+	input_abs_set_res(ts->input, ABS_MT_TOUCH_MAJOR, 1);
 
 	error = input_register_device(ts->input);
 	if (error) {

drivers/input/touchscreen/of_touchscreen.c

@@ -66,7 +66,7 @@ void touchscreen_parse_properties(struct input_dev *input, bool multitouch,
 {
 	struct device *dev = input->dev.parent;
 	struct input_absinfo *absinfo;
-	unsigned int axis;
+	unsigned int axis, axis_x, axis_y;
 	unsigned int minimum, maximum, fuzz;
 	bool data_present;
 
@@ -74,33 +74,34 @@ void touchscreen_parse_properties(struct input_dev *input, bool multitouch,
 	if (!input->absinfo)
 		return;
 
-	axis = multitouch ? ABS_MT_POSITION_X : ABS_X;
+	axis_x = multitouch ? ABS_MT_POSITION_X : ABS_X;
+	axis_y = multitouch ? ABS_MT_POSITION_Y : ABS_Y;
+
 	data_present = touchscreen_get_prop_u32(dev, "touchscreen-min-x",
-						input_abs_get_min(input, axis),
+						input_abs_get_min(input, axis_x),
 						&minimum) |
 		       touchscreen_get_prop_u32(dev, "touchscreen-size-x",
 						input_abs_get_max(input,
-								  axis) + 1,
+								  axis_x) + 1,
 						&maximum) |
 		       touchscreen_get_prop_u32(dev, "touchscreen-fuzz-x",
-						input_abs_get_fuzz(input, axis),
+						input_abs_get_fuzz(input, axis_x),
 						&fuzz);
 	if (data_present)
-		touchscreen_set_params(input, axis, minimum, maximum - 1, fuzz);
+		touchscreen_set_params(input, axis_x, minimum, maximum - 1, fuzz);
 
-	axis = multitouch ? ABS_MT_POSITION_Y : ABS_Y;
 	data_present = touchscreen_get_prop_u32(dev, "touchscreen-min-y",
-						input_abs_get_min(input, axis),
+						input_abs_get_min(input, axis_y),
 						&minimum) |
 		       touchscreen_get_prop_u32(dev, "touchscreen-size-y",
 						input_abs_get_max(input,
-								  axis) + 1,
+								  axis_y) + 1,
 						&maximum) |
 		       touchscreen_get_prop_u32(dev, "touchscreen-fuzz-y",
-						input_abs_get_fuzz(input, axis),
+						input_abs_get_fuzz(input, axis_y),
 						&fuzz);
 	if (data_present)
-		touchscreen_set_params(input, axis, minimum, maximum - 1, fuzz);
+		touchscreen_set_params(input, axis_y, minimum, maximum - 1, fuzz);
 
 	axis = multitouch ? ABS_MT_PRESSURE : ABS_PRESSURE;
 	data_present = touchscreen_get_prop_u32(dev,
@@ -117,15 +118,13 @@ void touchscreen_parse_properties(struct input_dev *input, bool multitouch,
 	if (!prop)
 		return;
 
-	axis = multitouch ? ABS_MT_POSITION_X : ABS_X;
-
-	prop->max_x = input_abs_get_max(input, axis);
-	prop->max_y = input_abs_get_max(input, axis + 1);
+	prop->max_x = input_abs_get_max(input, axis_x);
+	prop->max_y = input_abs_get_max(input, axis_y);
 
 	prop->invert_x =
 		device_property_read_bool(dev, "touchscreen-inverted-x");
 	if (prop->invert_x) {
-		absinfo = &input->absinfo[axis];
+		absinfo = &input->absinfo[axis_x];
 		absinfo->maximum -= absinfo->minimum;
 		absinfo->minimum = 0;
 	}
@@ -133,7 +132,7 @@ void touchscreen_parse_properties(struct input_dev *input, bool multitouch,
 	prop->invert_y =
 		device_property_read_bool(dev, "touchscreen-inverted-y");
 	if (prop->invert_y) {
-		absinfo = &input->absinfo[axis + 1];
+		absinfo = &input->absinfo[axis_y];
 		absinfo->maximum -= absinfo->minimum;
 		absinfo->minimum = 0;
 	}
@@ -141,7 +140,7 @@ void touchscreen_parse_properties(struct input_dev *input, bool multitouch,
 	prop->swap_x_y =
 		device_property_read_bool(dev, "touchscreen-swapped-x-y");
 	if (prop->swap_x_y)
-		swap(input->absinfo[axis], input->absinfo[axis + 1]);
+		swap(input->absinfo[axis_x], input->absinfo[axis_y]);
 }
 EXPORT_SYMBOL(touchscreen_parse_properties);
 

include/uapi/linux/input-event-codes.h

-/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
+/* SPDX-License-Identifier: GPL-2.0-only WITH Linux-syscall-note */
 /*
  * Input event codes
  *