MIPS: Netlogic: Add support for USB on XLP2xx

Add USB intialization code to handle the new XLP2XX USB 3.0 block.
This adds xlp/usb-init-xlp2.c to initialize the XLP2XX USB glue-logic
for XHCI and EHCI. Interrupt and IO offset code in xlp-hal/iomap.h
and xlp/nlm_hal.c is also updated for the new USB block.
Signed-off-by: NGanesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: NJayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5744/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

arch/mips/include/asm/netlogic/xlp-hal/iomap.h

@@ -72,6 +72,12 @@
 #define XLP_IO_USB_OHCI2_OFFSET(node)	XLP_HDR_OFFSET(node, 0, 2, 4)
 #define XLP_IO_USB_OHCI3_OFFSET(node)	XLP_HDR_OFFSET(node, 0, 2, 5)
 
+/* XLP2xx has an updated USB block */
+#define XLP2XX_IO_USB_OFFSET(node, i)	XLP_HDR_OFFSET(node, 0, 4, i)
+#define XLP2XX_IO_USB_XHCI0_OFFSET(node)	XLP_HDR_OFFSET(node, 0, 4, 1)
+#define XLP2XX_IO_USB_XHCI1_OFFSET(node)	XLP_HDR_OFFSET(node, 0, 4, 2)
+#define XLP2XX_IO_USB_XHCI2_OFFSET(node)	XLP_HDR_OFFSET(node, 0, 4, 3)
+
 #define XLP_IO_NAE_OFFSET(node)		XLP_HDR_OFFSET(node, 0, 3, 0)
 #define XLP_IO_POE_OFFSET(node)		XLP_HDR_OFFSET(node, 0, 3, 1)
 
@@ -148,6 +154,7 @@
 #define PCI_DEVICE_ID_NLM_NOR		0x1015
 #define PCI_DEVICE_ID_NLM_NAND		0x1016
 #define PCI_DEVICE_ID_NLM_MMC		0x1018
+#define PCI_DEVICE_ID_NLM_XHCI		0x101d
 
 #ifndef __ASSEMBLY__
 

arch/mips/include/asm/netlogic/xlp-hal/xlp.h

@@ -41,12 +41,17 @@
 #define PIC_PCIE_LINK_1_IRQ		20
 #define PIC_PCIE_LINK_2_IRQ		21
 #define PIC_PCIE_LINK_3_IRQ		22
+
 #define PIC_EHCI_0_IRQ			23
 #define PIC_EHCI_1_IRQ			24
 #define PIC_OHCI_0_IRQ			25
 #define PIC_OHCI_1_IRQ			26
 #define PIC_OHCI_2_IRQ			27
 #define PIC_OHCI_3_IRQ			28
+#define PIC_2XX_XHCI_0_IRQ		23
+#define PIC_2XX_XHCI_1_IRQ		24
+#define PIC_2XX_XHCI_2_IRQ		25
+
 #define PIC_MMC_IRQ			29
 #define PIC_I2C_0_IRQ			30
 #define PIC_I2C_1_IRQ			31

arch/mips/netlogic/xlp/Makefile

 obj-y				+= setup.o nlm_hal.o cop2-ex.o dt.o
 obj-$(CONFIG_SMP)		+= wakeup.o
 obj-$(CONFIG_USB)		+= usb-init.o
+obj-$(CONFIG_USB)		+= usb-init-xlp2.o

arch/mips/netlogic/xlp/nlm_hal.c

@@ -65,6 +65,7 @@ int nlm_irq_to_irt(int irq)
 	uint64_t pcibase;
 	int devoff, irt;
 
+	devoff = 0;
 	switch (irq) {
 	case PIC_UART_0_IRQ:
 		devoff = XLP_IO_UART0_OFFSET(0);
@@ -72,24 +73,6 @@ int nlm_irq_to_irt(int irq)
 	case PIC_UART_1_IRQ:
 		devoff = XLP_IO_UART1_OFFSET(0);
 		break;
-	case PIC_EHCI_0_IRQ:
-		devoff = XLP_IO_USB_EHCI0_OFFSET(0);
-		break;
-	case PIC_EHCI_1_IRQ:
-		devoff = XLP_IO_USB_EHCI1_OFFSET(0);
-		break;
-	case PIC_OHCI_0_IRQ:
-		devoff = XLP_IO_USB_OHCI0_OFFSET(0);
-		break;
-	case PIC_OHCI_1_IRQ:
-		devoff = XLP_IO_USB_OHCI1_OFFSET(0);
-		break;
-	case PIC_OHCI_2_IRQ:
-		devoff = XLP_IO_USB_OHCI2_OFFSET(0);
-		break;
-	case PIC_OHCI_3_IRQ:
-		devoff = XLP_IO_USB_OHCI3_OFFSET(0);
-		break;
 	case PIC_MMC_IRQ:
 		devoff = XLP_IO_SD_OFFSET(0);
 		break;
@@ -103,8 +86,41 @@ int nlm_irq_to_irt(int irq)
 			devoff = XLP_IO_I2C0_OFFSET(0);
 		break;
 	default:
-		devoff = 0;
-		break;
+		if (cpu_is_xlpii()) {
+			switch (irq) {
+				/* XLP2XX has three XHCI USB controller */
+			case PIC_2XX_XHCI_0_IRQ:
+				devoff = XLP2XX_IO_USB_XHCI0_OFFSET(0);
+				break;
+			case PIC_2XX_XHCI_1_IRQ:
+				devoff = XLP2XX_IO_USB_XHCI1_OFFSET(0);
+				break;
+			case PIC_2XX_XHCI_2_IRQ:
+				devoff = XLP2XX_IO_USB_XHCI2_OFFSET(0);
+				break;
+			}
+		} else {
+			switch (irq) {
+			case PIC_EHCI_0_IRQ:
+				devoff = XLP_IO_USB_EHCI0_OFFSET(0);
+				break;
+			case PIC_EHCI_1_IRQ:
+				devoff = XLP_IO_USB_EHCI1_OFFSET(0);
+				break;
+			case PIC_OHCI_0_IRQ:
+				devoff = XLP_IO_USB_OHCI0_OFFSET(0);
+				break;
+			case PIC_OHCI_1_IRQ:
+				devoff = XLP_IO_USB_OHCI1_OFFSET(0);
+				break;
+			case PIC_OHCI_2_IRQ:
+				devoff = XLP_IO_USB_OHCI2_OFFSET(0);
+				break;
+			case PIC_OHCI_3_IRQ:
+				devoff = XLP_IO_USB_OHCI3_OFFSET(0);
+				break;
+			}
+		}
 	}
 
 	if (devoff != 0) {

arch/mips/netlogic/xlp/usb-init-xlp2.c

+/*
+ * Copyright (c) 2003-2013 Broadcom Corporation
+ * All Rights Reserved
+ *
+ * This software is available to you under a choice of one of two
+ * licenses.  You may choose to be licensed under the terms of the GNU
+ * General Public License (GPL) Version 2, available from the file
+ * COPYING in the main directory of this source tree, or the Broadcom
+ * license below:
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ *    notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ *    notice, this list of conditions and the following disclaimer in
+ *    the documentation and/or other materials provided with the
+ *    distribution.
+ *
+ * THIS SOFTWARE IS PROVIDED BY BROADCOM ``AS IS'' AND ANY EXPRESS OR
+ * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL BROADCOM OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
+ * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
+ * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
+ * OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
+ * IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#include <linux/dma-mapping.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/irq.h>
+
+#include <asm/netlogic/common.h>
+#include <asm/netlogic/haldefs.h>
+#include <asm/netlogic/xlp-hal/iomap.h>
+#include <asm/netlogic/xlp-hal/xlp.h>
+
+#define XLPII_USB3_CTL_0		0xc0
+#define XLPII_VAUXRST			BIT(0)
+#define XLPII_VCCRST			BIT(1)
+#define XLPII_NUM2PORT			9
+#define XLPII_NUM3PORT			13
+#define XLPII_RTUNEREQ			BIT(20)
+#define XLPII_MS_CSYSREQ		BIT(21)
+#define XLPII_XS_CSYSREQ		BIT(22)
+#define XLPII_RETENABLEN		BIT(23)
+#define XLPII_TX2RX			BIT(24)
+#define XLPII_XHCIREV			BIT(25)
+#define XLPII_ECCDIS			BIT(26)
+
+#define XLPII_USB3_INT_REG		0xc2
+#define XLPII_USB3_INT_MASK		0xc3
+
+#define XLPII_USB_PHY_TEST		0xc6
+#define XLPII_PRESET			BIT(0)
+#define XLPII_ATERESET			BIT(1)
+#define XLPII_LOOPEN			BIT(2)
+#define XLPII_TESTPDHSP			BIT(3)
+#define XLPII_TESTPDSSP			BIT(4)
+#define XLPII_TESTBURNIN		BIT(5)
+
+#define XLPII_USB_PHY_LOS_LV		0xc9
+#define XLPII_LOSLEV			0
+#define XLPII_LOSBIAS			5
+#define XLPII_SQRXTX			8
+#define XLPII_TXBOOST			11
+#define XLPII_RSLKSEL			16
+#define XLPII_FSEL			20
+
+#define XLPII_USB_RFCLK_REG		0xcc
+#define XLPII_VVLD			30
+
+#define nlm_read_usb_reg(b, r)		nlm_read_reg(b, r)
+#define nlm_write_usb_reg(b, r, v)	nlm_write_reg(b, r, v)
+
+#define nlm_xlpii_get_usb_pcibase(node, inst)		\
+	nlm_pcicfg_base(XLP2XX_IO_USB_OFFSET(node, inst))
+#define nlm_xlpii_get_usb_regbase(node, inst)		\
+	(nlm_xlpii_get_usb_pcibase(node, inst) + XLP_IO_PCI_HDRSZ)
+
+static void xlpii_usb_ack(struct irq_data *data)
+{
+	u64 port_addr;
+
+	switch (data->irq) {
+	case PIC_2XX_XHCI_0_IRQ:
+		port_addr = nlm_xlpii_get_usb_regbase(0, 1);
+		break;
+	case PIC_2XX_XHCI_1_IRQ:
+		port_addr = nlm_xlpii_get_usb_regbase(0, 2);
+		break;
+	case PIC_2XX_XHCI_2_IRQ:
+		port_addr = nlm_xlpii_get_usb_regbase(0, 3);
+		break;
+	default:
+		pr_err("No matching USB irq!\n");
+		return;
+	}
+	nlm_write_usb_reg(port_addr, XLPII_USB3_INT_REG, 0xffffffff);
+}
+
+static void nlm_xlpii_usb_hw_reset(int node, int port)
+{
+	u64 port_addr, xhci_base, pci_base;
+	void __iomem *corebase;
+	u32 val;
+
+	port_addr = nlm_xlpii_get_usb_regbase(node, port);
+
+	/* Set frequency */
+	val = nlm_read_usb_reg(port_addr, XLPII_USB_PHY_LOS_LV);
+	val &= ~(0x3f << XLPII_FSEL);
+	val |= (0x27 << XLPII_FSEL);
+	nlm_write_usb_reg(port_addr, XLPII_USB_PHY_LOS_LV, val);
+
+	val = nlm_read_usb_reg(port_addr, XLPII_USB_RFCLK_REG);
+	val |= (1 << XLPII_VVLD);
+	nlm_write_usb_reg(port_addr, XLPII_USB_RFCLK_REG, val);
+
+	/* PHY reset */
+	val = nlm_read_usb_reg(port_addr, XLPII_USB_PHY_TEST);
+	val &= (XLPII_ATERESET | XLPII_LOOPEN | XLPII_TESTPDHSP
+		| XLPII_TESTPDSSP | XLPII_TESTBURNIN);
+	nlm_write_usb_reg(port_addr, XLPII_USB_PHY_TEST, val);
+
+	/* Setup control register */
+	val =  XLPII_VAUXRST | XLPII_VCCRST | (1 << XLPII_NUM2PORT)
+		| (1 << XLPII_NUM3PORT) | XLPII_MS_CSYSREQ | XLPII_XS_CSYSREQ
+		| XLPII_RETENABLEN | XLPII_XHCIREV;
+	nlm_write_usb_reg(port_addr, XLPII_USB3_CTL_0, val);
+
+	/* Enable interrupts */
+	nlm_write_usb_reg(port_addr, XLPII_USB3_INT_MASK, 0x00000001);
+
+	/* Clear all interrupts */
+	nlm_write_usb_reg(port_addr, XLPII_USB3_INT_REG, 0xffffffff);
+
+	udelay(2000);
+
+	/* XHCI configuration at PCI mem */
+	pci_base = nlm_xlpii_get_usb_pcibase(node, port);
+	xhci_base = nlm_read_usb_reg(pci_base, 0x4) & ~0xf;
+	corebase = ioremap(xhci_base, 0x10000);
+	if (!corebase)
+		return;
+
+	writel(0x240002, corebase + 0xc2c0);
+	/* GCTL 0xc110 */
+	val = readl(corebase + 0xc110);
+	val &= ~(0x3 << 12);
+	val |= (1 << 12);
+	writel(val, corebase + 0xc110);
+	udelay(100);
+
+	/* PHYCFG 0xc200 */
+	val = readl(corebase + 0xc200);
+	val &= ~(1 << 6);
+	writel(val, corebase + 0xc200);
+	udelay(100);
+
+	/* PIPECTL 0xc2c0 */
+	val = readl(corebase + 0xc2c0);
+	val &= ~(1 << 17);
+	writel(val, corebase + 0xc2c0);
+
+	iounmap(corebase);
+}
+
+static int __init nlm_platform_xlpii_usb_init(void)
+{
+	if (!cpu_is_xlpii())
+		return 0;
+
+	pr_info("Initializing 2XX USB Interface\n");
+	nlm_xlpii_usb_hw_reset(0, 1);
+	nlm_xlpii_usb_hw_reset(0, 2);
+	nlm_xlpii_usb_hw_reset(0, 3);
+	nlm_set_pic_extra_ack(0, PIC_2XX_XHCI_0_IRQ, xlpii_usb_ack);
+	nlm_set_pic_extra_ack(0, PIC_2XX_XHCI_1_IRQ, xlpii_usb_ack);
+	nlm_set_pic_extra_ack(0, PIC_2XX_XHCI_2_IRQ, xlpii_usb_ack);
+
+	return 0;
+}
+
+arch_initcall(nlm_platform_xlpii_usb_init);
+
+static u64 xlp_usb_dmamask = ~(u32)0;
+
+/* Fixup IRQ for USB devices on XLP the SoC PCIe bus */
+static void nlm_usb_fixup_final(struct pci_dev *dev)
+{
+	dev->dev.dma_mask		= &xlp_usb_dmamask;
+	dev->dev.coherent_dma_mask	= DMA_BIT_MASK(32);
+	switch (dev->devfn) {
+	case 0x21:
+		dev->irq = PIC_2XX_XHCI_0_IRQ;
+		break;
+	case 0x22:
+		dev->irq = PIC_2XX_XHCI_1_IRQ;
+		break;
+	case 0x23:
+		dev->irq = PIC_2XX_XHCI_2_IRQ;
+		break;
+	}
+}
+
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_NETLOGIC, PCI_DEVICE_ID_NLM_XHCI,
+		nlm_usb_fixup_final);

arch/mips/netlogic/xlp/usb-init.c

@@ -99,6 +99,9 @@ static void nlm_usb_hw_reset(int node, int port)
 
 static int __init nlm_platform_usb_init(void)
 {
+	if (cpu_is_xlpii())
+		return 0;
+
 	pr_info("Initializing USB Interface\n");
 	nlm_usb_hw_reset(0, 0);
 	nlm_usb_hw_reset(0, 3);