ARM: dts: Move BCM2711 RPi specific into separate dtsi

There is a lot of Raspberry Pi specific stuff (neither SoC or board
specific) for the BCM2711 which is currently in the RPi 4 B dts. In order
to avoid copy & paste for every new BCM2711 based Raspberry Pi, move it
into a separate dtsi.
Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1622981777-5023-4-git-send-email-stefan.wahren@i2se.comSigned-off-by: NNicolas Saenz Julienne <nsaenz@kernel.org>

arch/arm/boot/dts/bcm2711-rpi-4-b.dts

 // SPDX-License-Identifier: GPL-2.0
 /dts-v1/;
 #include "bcm2711.dtsi"
-#include "bcm2835-rpi.dtsi"
+#include "bcm2711-rpi.dtsi"
 #include "bcm283x-rpi-usb-peripheral.dtsi"
 
-#include <dt-bindings/reset/raspberrypi,firmware-reset.h>
-
 / {
 	compatible = "raspberrypi,4-model-b", "brcm,bcm2711";
 	model = "Raspberry Pi 4 Model B";
@@ -15,19 +13,6 @@
 		stdout-path = "serial1:115200n8";
 	};
 
-	/* Will be filled by the bootloader */
-	memory@0 {
-		device_type = "memory";
-		reg = <0 0 0>;
-	};
-
-	aliases {
-		emmc2bus = &emmc2bus;
-		ethernet0 = &genet;
-		pcie0 = &pcie0;
-		blconfig = &blconfig;
-	};
-
 	leds {
 		act {
 			gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
@@ -79,31 +64,15 @@
 	status = "okay";
 };
 
-&firmware {
-	firmware_clocks: clocks {
-		compatible = "raspberrypi,firmware-clocks";
-		#clock-cells = <1>;
-	};
-
-	expgpio: gpio {
-		compatible = "raspberrypi,firmware-gpio";
-		gpio-controller;
-		#gpio-cells = <2>;
-		gpio-line-names = "BT_ON",
-				  "WL_ON",
-				  "PWR_LED_OFF",
-				  "GLOBAL_RESET",
-				  "VDD_SD_IO_SEL",
-				  "CAM_GPIO",
-				  "SD_PWR_ON",
-				  "";
-		status = "okay";
-	};
-
-	reset: reset {
-		compatible = "raspberrypi,firmware-reset";
-		#reset-cells = <1>;
-	};
+&expgpio {
+	gpio-line-names = "BT_ON",
+			  "WL_ON",
+			  "PWR_LED_OFF",
+			  "GLOBAL_RESET",
+			  "VDD_SD_IO_SEL",
+			  "CAM_GPIO",
+			  "SD_PWR_ON",
+			  "";
 };
 
 &gpio {
@@ -180,23 +149,13 @@
 };
 
 &hdmi0 {
-	clocks = <&firmware_clocks 13>, <&firmware_clocks 14>, <&dvp 0>, <&clk_27MHz>;
-	clock-names = "hdmi", "bvb", "audio", "cec";
-	wifi-2.4ghz-coexistence;
 	status = "okay";
 };
 
 &hdmi1 {
-	clocks = <&firmware_clocks 13>, <&firmware_clocks 14>, <&dvp 1>, <&clk_27MHz>;
-	clock-names = "hdmi", "bvb", "audio", "cec";
-	wifi-2.4ghz-coexistence;
 	status = "okay";
 };
 
-&hvs {
-	clocks = <&firmware_clocks 4>;
-};
-
 &pixelvalve0 {
 	status = "okay";
 };
@@ -219,22 +178,6 @@
 	status = "okay";
 };
 
-&rmem {
-	/*
-	 * RPi4's co-processor will copy the board's bootloader configuration
-	 * into memory for the OS to consume. It'll also update this node with
-	 * its placement information.
-	 */
-	blconfig: nvram@0 {
-		compatible = "raspberrypi,bootloader-config", "nvmem-rmem";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		reg = <0x0 0x0 0x0>;
-		no-map;
-		status = "disabled";
-	};
-};
-
 /* SDHCI is used to control the SDIO for wireless */
 &sdhci {
 	#address-cells = <1>;
@@ -309,10 +252,6 @@
 	status = "okay";
 };
 
-&vchiq {
-	interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
-};
-
 &vc4 {
 	status = "okay";
 };

arch/arm/boot/dts/bcm2711-rpi.dtsi

+// SPDX-License-Identifier: GPL-2.0
+#include "bcm2835-rpi.dtsi"
+
+#include <dt-bindings/reset/raspberrypi,firmware-reset.h>
+
+/ {
+	/* Will be filled by the bootloader */
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0 0>;
+	};
+
+	aliases {
+		emmc2bus = &emmc2bus;
+		ethernet0 = &genet;
+		pcie0 = &pcie0;
+		blconfig = &blconfig;
+	};
+};
+
+&firmware {
+	firmware_clocks: clocks {
+		compatible = "raspberrypi,firmware-clocks";
+		#clock-cells = <1>;
+	};
+
+	expgpio: gpio {
+		compatible = "raspberrypi,firmware-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		status = "okay";
+	};
+
+	reset: reset {
+		compatible = "raspberrypi,firmware-reset";
+		#reset-cells = <1>;
+	};
+};
+
+&hdmi0 {
+	clocks = <&firmware_clocks 13>, <&firmware_clocks 14>, <&dvp 0>, <&clk_27MHz>;
+	clock-names = "hdmi", "bvb", "audio", "cec";
+	wifi-2.4ghz-coexistence;
+};
+
+&hdmi1 {
+	clocks = <&firmware_clocks 13>, <&firmware_clocks 14>, <&dvp 1>, <&clk_27MHz>;
+	clock-names = "hdmi", "bvb", "audio", "cec";
+	wifi-2.4ghz-coexistence;
+};
+
+&hvs {
+	clocks = <&firmware_clocks 4>;
+};
+
+&rmem {
+	/*
+	 * RPi4's co-processor will copy the board's bootloader configuration
+	 * into memory for the OS to consume. It'll also update this node with
+	 * its placement information.
+	 */
+	blconfig: nvram@0 {
+		compatible = "raspberrypi,bootloader-config", "nvmem-rmem";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0 0x0 0x0>;
+		no-map;
+		status = "disabled";
+	};
+};
+
+&vchiq {
+	interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+};