提交 97132776 编写于 作者: G Glauber de Oliveira Costa 提交者: Ingo Molnar

x86: boot cpus from cpu_up, instead of prepare_cpus

After all the infrastructure work, we're now prepared
to boot the cpus from cpu_up, and not from prepare_cpus.
So the difference between cold boot and hotplug is effectively
over, and the functions are used to the purposes they're meant to.
Signed-off-by: NGlauber Costa <gcosta@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
上级 d2bcbad5
......@@ -670,6 +670,7 @@ void cpu_exit_clear(void)
cpu_clear(cpu, smp_commenced_mask);
unmap_cpu_to_logical_apicid(cpu);
}
#endif
struct warm_boot_cpu_info {
struct completion *complete;
......@@ -710,7 +711,6 @@ static void __cpuinit __smp_prepare_cpu(int cpu)
wait_for_completion(&done);
}
}
#endif
static int boot_cpu_logical_apicid;
/* Where the IO area was mapped on multiquad, always 0 otherwise */
......@@ -790,8 +790,6 @@ static int __init smp_sanity_check(unsigned max_cpus)
*/
static void __init smp_boot_cpus(unsigned int max_cpus)
{
int apicid, cpu, bit, kicked;
/*
* Setup boot CPU information
*/
......@@ -819,39 +817,6 @@ static void __init smp_boot_cpus(unsigned int max_cpus)
setup_portio_remap();
/*
* Scan the CPU present map and fire up the other CPUs via do_boot_cpu
*
* In clustered apic mode, phys_cpu_present_map is a constructed thus:
* bits 0-3 are quad0, 4-7 are quad1, etc. A perverse twist on the
* clustered apic ID.
*/
Dprintk("CPU present map: %lx\n", physids_coerce(phys_cpu_present_map));
kicked = 1;
for (bit = 0; kicked < NR_CPUS && bit < MAX_APICS; bit++) {
apicid = cpu_present_to_apicid(bit);
/*
* Don't even attempt to start the boot CPU!
*/
if ((apicid == boot_cpu_apicid) || (apicid == BAD_APICID))
continue;
if (!check_apicid_present(bit))
continue;
if (max_cpus <= cpus_weight(cpu_present_map))
continue;
/* Utterly temporary */
for (cpu = 0; cpu < NR_CPUS; cpu++)
if (per_cpu(x86_cpu_to_apicid, cpu) == apicid)
break;
if (do_boot_cpu(apicid, cpu))
printk("CPU #%d not responding - cannot use it.\n",
apicid);
else
++kicked;
}
smpboot_setup_io_apic();
setup_boot_clock();
......@@ -895,17 +860,8 @@ int __cpuinit native_cpu_up(unsigned int cpu)
}
per_cpu(cpu_state, cpu) = CPU_UP_PREPARE;
#ifdef CONFIG_HOTPLUG_CPU
/*
* We do warm boot only on cpus that had booted earlier
* Otherwise cold boot is all handled from smp_boot_cpus().
* cpu_callin_map is set during AP kickstart process. Its reset
* when a cpu is taken offline from cpu_exit_clear().
*/
if (!cpu_isset(cpu, cpu_callin_map))
__smp_prepare_cpu(cpu);
#endif
__smp_prepare_cpu(cpu);
/* In case one didn't come up */
if (!cpu_isset(cpu, cpu_callin_map)) {
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册