提交 938e1426 编写于 作者: L Linus Torvalds

Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux

Pull i2c fixes from Wolfram Sang:
 "Two bugfixes, one v4.16 regression fix, and two documentation fixes"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: designware: Consider SCL GPIO optional
  i2c: busses: i2c-sirf: Fix spelling: "formular" -> "formula".
  i2c: bcm2835: Set up the rising/falling edge delays
  i2c: i801: Add missing documentation entries for Braswell and Kaby Lake
  i2c: designware: must wait for enable
......@@ -28,8 +28,10 @@ Supported adapters:
* Intel Wildcat Point (PCH)
* Intel Wildcat Point-LP (PCH)
* Intel BayTrail (SOC)
* Intel Braswell (SOC)
* Intel Sunrise Point-H (PCH)
* Intel Sunrise Point-LP (PCH)
* Intel Kaby Lake-H (PCH)
* Intel DNV (SOC)
* Intel Broxton (SOC)
* Intel Lewisburg (PCH)
......
......@@ -123,8 +123,10 @@ config I2C_I801
Wildcat Point (PCH)
Wildcat Point-LP (PCH)
BayTrail (SOC)
Braswell (SOC)
Sunrise Point-H (PCH)
Sunrise Point-LP (PCH)
Kaby Lake-H (PCH)
DNV (SOC)
Broxton (SOC)
Lewisburg (PCH)
......
......@@ -50,6 +50,9 @@
#define BCM2835_I2C_S_CLKT BIT(9)
#define BCM2835_I2C_S_LEN BIT(10) /* Fake bit for SW error reporting */
#define BCM2835_I2C_FEDL_SHIFT 16
#define BCM2835_I2C_REDL_SHIFT 0
#define BCM2835_I2C_CDIV_MIN 0x0002
#define BCM2835_I2C_CDIV_MAX 0xFFFE
......@@ -81,7 +84,7 @@ static inline u32 bcm2835_i2c_readl(struct bcm2835_i2c_dev *i2c_dev, u32 reg)
static int bcm2835_i2c_set_divider(struct bcm2835_i2c_dev *i2c_dev)
{
u32 divider;
u32 divider, redl, fedl;
divider = DIV_ROUND_UP(clk_get_rate(i2c_dev->clk),
i2c_dev->bus_clk_rate);
......@@ -100,6 +103,22 @@ static int bcm2835_i2c_set_divider(struct bcm2835_i2c_dev *i2c_dev)
bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_DIV, divider);
/*
* Number of core clocks to wait after falling edge before
* outputting the next data bit. Note that both FEDL and REDL
* can't be greater than CDIV/2.
*/
fedl = max(divider / 16, 1u);
/*
* Number of core clocks to wait after rising edge before
* sampling the next incoming data bit.
*/
redl = max(divider / 4, 1u);
bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_DEL,
(fedl << BCM2835_I2C_FEDL_SHIFT) |
(redl << BCM2835_I2C_REDL_SHIFT));
return 0;
}
......
......@@ -209,7 +209,7 @@ static void i2c_dw_xfer_init(struct dw_i2c_dev *dev)
i2c_dw_disable_int(dev);
/* Enable the adapter */
__i2c_dw_enable(dev, true);
__i2c_dw_enable_and_wait(dev, true);
/* Clear and enable interrupts */
dw_readl(dev, DW_IC_CLR_INTR);
......@@ -644,7 +644,7 @@ static int i2c_dw_init_recovery_info(struct dw_i2c_dev *dev)
gpio = devm_gpiod_get(dev->dev, "scl", GPIOD_OUT_HIGH);
if (IS_ERR(gpio)) {
r = PTR_ERR(gpio);
if (r == -ENOENT)
if (r == -ENOENT || r == -ENOSYS)
return 0;
return r;
}
......
......@@ -58,6 +58,7 @@
* Wildcat Point (PCH) 0x8ca2 32 hard yes yes yes
* Wildcat Point-LP (PCH) 0x9ca2 32 hard yes yes yes
* BayTrail (SOC) 0x0f12 32 hard yes yes yes
* Braswell (SOC) 0x2292 32 hard yes yes yes
* Sunrise Point-H (PCH) 0xa123 32 hard yes yes yes
* Sunrise Point-LP (PCH) 0x9d23 32 hard yes yes yes
* DNV (SOC) 0x19df 32 hard yes yes yes
......
......@@ -341,7 +341,7 @@ static int i2c_sirfsoc_probe(struct platform_device *pdev)
platform_set_drvdata(pdev, adap);
init_completion(&siic->done);
/* Controller Initalisation */
/* Controller initialisation */
writel(SIRFSOC_I2C_RESET, siic->base + SIRFSOC_I2C_CTRL);
while (readl(siic->base + SIRFSOC_I2C_CTRL) & SIRFSOC_I2C_RESET)
......@@ -369,7 +369,7 @@ static int i2c_sirfsoc_probe(struct platform_device *pdev)
* but they start to affect the speed when clock is set to faster
* frequencies.
* Through the actual tests, use the different user_div value(which
* in the divider formular 'Fio / (Fi2c * user_div)') to adapt
* in the divider formula 'Fio / (Fi2c * user_div)') to adapt
* the different ranges of i2c bus clock frequency, to make the SCL
* more accurate.
*/
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册