提交 83a36838 编写于 作者: K Kyungmin Park 提交者: Thomas Gleixner

[MTD] OneNAND: Enhanced support for DDP (Dual Densitiy Packages)

Add density mask for better support of DDP chips.
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
上级 a41371eb
......@@ -84,25 +84,23 @@ static void onenand_writew(unsigned short value, void __iomem *addr)
/**
* onenand_block_address - [DEFAULT] Get block address
* @param device the device id
* @param this onenand chip data structure
* @param block the block
* @return translated block address if DDP, otherwise same
*
* Setup Start Address 1 Register (F100h)
*/
static int onenand_block_address(int device, int block)
static int onenand_block_address(struct onenand_chip *this, int block)
{
if (device & ONENAND_DEVICE_IS_DDP) {
if (this->device_id & ONENAND_DEVICE_IS_DDP) {
/* Device Flash Core select, NAND Flash Block Address */
int dfs = 0, density, mask;
int dfs = 0;
density = device >> ONENAND_DEVICE_DENSITY_SHIFT;
mask = (1 << (density + 6));
if (block & mask)
if (block & this->density_mask)
dfs = 1;
return (dfs << ONENAND_DDP_SHIFT) | (block & (mask - 1));
return (dfs << ONENAND_DDP_SHIFT) |
(block & (this->density_mask - 1));
}
return block;
......@@ -110,22 +108,19 @@ static int onenand_block_address(int device, int block)
/**
* onenand_bufferram_address - [DEFAULT] Get bufferram address
* @param device the device id
* @param this onenand chip data structure
* @param block the block
* @return set DBS value if DDP, otherwise 0
*
* Setup Start Address 2 Register (F101h) for DDP
*/
static int onenand_bufferram_address(int device, int block)
static int onenand_bufferram_address(struct onenand_chip *this, int block)
{
if (device & ONENAND_DEVICE_IS_DDP) {
if (this->device_id & ONENAND_DEVICE_IS_DDP) {
/* Device BufferRAM Select */
int dbs = 0, density, mask;
density = device >> ONENAND_DEVICE_DENSITY_SHIFT;
mask = (1 << (density + 6));
int dbs = 0;
if (block & mask)
if (block & this->density_mask)
dbs = 1;
return (dbs << ONENAND_DDP_SHIFT);
......@@ -223,7 +218,7 @@ static int onenand_command(struct mtd_info *mtd, int cmd, loff_t addr, size_t le
/* NOTE: The setting order of the registers is very important! */
if (cmd == ONENAND_CMD_BUFFERRAM) {
/* Select DataRAM for DDP */
value = onenand_bufferram_address(this->device_id, block);
value = onenand_bufferram_address(this, block);
this->write_word(value, this->base + ONENAND_REG_START_ADDRESS2);
/* Switch to the next data buffer */
......@@ -234,7 +229,7 @@ static int onenand_command(struct mtd_info *mtd, int cmd, loff_t addr, size_t le
if (block != -1) {
/* Write 'DFS, FBA' of Flash */
value = onenand_block_address(this->device_id, block);
value = onenand_block_address(this, block);
this->write_word(value, this->base + ONENAND_REG_START_ADDRESS1);
}
......@@ -263,7 +258,7 @@ static int onenand_command(struct mtd_info *mtd, int cmd, loff_t addr, size_t le
if (readcmd) {
/* Select DataRAM for DDP */
value = onenand_bufferram_address(this->device_id, block);
value = onenand_bufferram_address(this, block);
this->write_word(value, this->base + ONENAND_REG_START_ADDRESS2);
}
}
......@@ -1313,7 +1308,7 @@ static int onenand_unlock(struct mtd_info *mtd, loff_t ofs, size_t len)
continue;
/* Set block address for read block status */
value = onenand_block_address(this->device_id, block);
value = onenand_block_address(this, block);
this->write_word(value, this->base + ONENAND_REG_START_ADDRESS1);
/* Check lock status */
......@@ -1415,6 +1410,8 @@ static int onenand_probe(struct mtd_info *mtd)
density = dev_id >> ONENAND_DEVICE_DENSITY_SHIFT;
this->chipsize = (16 << density) << 20;
/* Set density mask. it is used for DDP */
this->density_mask = (1 << (density + 6));
/* OneNAND page size & block size */
/* The data buffer size is equal to page size */
......
......@@ -84,6 +84,7 @@ struct onenand_chip {
void __iomem *base;
unsigned int chipsize;
unsigned int device_id;
unsigned int density_mask;
unsigned int options;
unsigned int erase_shift;
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册