提交 826575fc 编写于 作者: G Greg Kroah-Hartman

USB: serial: keyspan_pda.c: remove dbg() usage

dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
上级 255b703a
......@@ -137,8 +137,8 @@ static void keyspan_pda_request_unthrottle(struct work_struct *work)
0,
2000);
if (result < 0)
dbg("%s - error %d from usb_control_msg",
__func__, result);
dev_dbg(&serial->dev->dev, "%s - error %d from usb_control_msg\n",
__func__, result);
}
......@@ -160,12 +160,10 @@ static void keyspan_pda_rx_interrupt(struct urb *urb)
case -ENOENT:
case -ESHUTDOWN:
/* this urb is terminated, clean up */
dbg("%s - urb shutting down with status: %d",
__func__, status);
dev_dbg(&urb->dev->dev, "%s - urb shutting down with status: %d\n", __func__, status);
return;
default:
dbg("%s - nonzero urb status received: %d",
__func__, status);
dev_dbg(&urb->dev->dev, "%s - nonzero urb status received: %d\n", __func__, status);
goto exit;
}
......@@ -183,7 +181,7 @@ static void keyspan_pda_rx_interrupt(struct urb *urb)
break;
case 1:
/* status interrupt */
dbg(" rx int, d1=%d, d2=%d", data[1], data[2]);
dev_dbg(&port->dev, "rx int, d1=%d, d2=%d\n", data[1], data[2]);
switch (data[1]) {
case 1: /* modemline change */
break;
......@@ -229,7 +227,7 @@ static void keyspan_pda_rx_unthrottle(struct tty_struct *tty)
/* just restart the receive interrupt URB */
if (usb_submit_urb(port->interrupt_in_urb, GFP_KERNEL))
dbg(" usb_submit_urb(read urb) failed");
dev_dbg(&port->dev, "usb_submit_urb(read urb) failed\n");
}
......@@ -308,8 +306,8 @@ static void keyspan_pda_break_ctl(struct tty_struct *tty, int break_state)
USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT,
value, 0, NULL, 0, 2000);
if (result < 0)
dbg("%s - error %d from usb_control_msg",
__func__, result);
dev_dbg(&port->dev, "%s - error %d from usb_control_msg\n",
__func__, result);
/* there is something funky about this.. the TCSBRK that 'cu' performs
ought to translate into a break_ctl(-1),break_ctl(0) pair HZ/4
seconds apart, but it feels like the break sent isn't as long as it
......@@ -347,7 +345,7 @@ static void keyspan_pda_set_termios(struct tty_struct *tty,
speed = keyspan_pda_setbaud(serial, speed);
if (speed == 0) {
dbg("can't handle requested baud rate");
dev_dbg(&port->dev, "can't handle requested baud rate\n");
/* It hasn't changed so.. */
speed = tty_termios_baud_rate(old_termios);
}
......@@ -459,7 +457,7 @@ static int keyspan_pda_write(struct tty_struct *tty,
Block if we can't write anything at all, otherwise write as much as
we can. */
if (count == 0) {
dbg(" write request of 0 bytes");
dev_dbg(&port->dev, "write request of 0 bytes\n");
return 0;
}
......@@ -505,16 +503,16 @@ static int keyspan_pda_write(struct tty_struct *tty,
1,
2000);
if (rc > 0) {
dbg(" roomquery says %d", *room);
dev_dbg(&port->dev, "roomquery says %d\n", *room);
priv->tx_room = *room;
}
kfree(room);
if (rc < 0) {
dbg(" roomquery failed");
dev_dbg(&port->dev, "roomquery failed\n");
goto exit;
}
if (rc == 0) {
dbg(" roomquery returned 0 bytes");
dev_dbg(&port->dev, "roomquery returned 0 bytes\n");
rc = -EIO; /* device didn't return any data */
goto exit;
}
......@@ -536,7 +534,7 @@ static int keyspan_pda_write(struct tty_struct *tty,
rc = usb_submit_urb(port->write_urb, GFP_ATOMIC);
if (rc) {
dbg(" usb_submit_urb(write bulk) failed");
dev_dbg(&port->dev, "usb_submit_urb(write bulk) failed\n");
goto exit;
}
} else {
......@@ -639,11 +637,11 @@ static int keyspan_pda_open(struct tty_struct *tty,
1,
2000);
if (rc < 0) {
dbg("%s - roomquery failed", __func__);
dev_dbg(&port->dev, "%s - roomquery failed\n", __func__);
goto error;
}
if (rc == 0) {
dbg("%s - roomquery returned 0 bytes", __func__);
dev_dbg(&port->dev, "%s - roomquery returned 0 bytes\n", __func__);
rc = -EIO;
goto error;
}
......@@ -654,7 +652,7 @@ static int keyspan_pda_open(struct tty_struct *tty,
/*Start reading from the device*/
rc = usb_submit_urb(port->interrupt_in_urb, GFP_KERNEL);
if (rc) {
dbg("%s - usb_submit_urb(read int) failed", __func__);
dev_dbg(&port->dev, "%s - usb_submit_urb(read int) failed\n", __func__);
goto error;
}
error:
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册