PCI: qcom: Replace define with standard value

Lots of define are actually already defined in pci_regs.h, directly use
the standard defines.

Link: https://lore.kernel.org/r/20200615210608.21469-13-ansuelsmth@gmail.comSigned-off-by: NAnsuel Smith <ansuelsmth@gmail.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: NStanimir Varbanov <svarbanov@mm-sol.com>

drivers/pci/controller/dwc/pcie-qcom.c

@@ -40,11 +40,6 @@
 #define L23_CLK_RMV_DIS				BIT(2)
 #define L1_CLK_RMV_DIS				BIT(1)
 
-#define PCIE20_COMMAND_STATUS			0x04
-#define CMD_BME_VAL				0x4
-#define PCIE20_DEVICE_CONTROL2_STATUS2		0x98
-#define PCIE_CAP_CPL_TIMEOUT_DISABLE		0x10
-
 #define PCIE20_PARF_PHY_CTRL			0x40
 #define PHY_CTRL_PHY_TX0_TERM_OFFSET_MASK	GENMASK(20, 16)
 #define PHY_CTRL_PHY_TX0_TERM_OFFSET(x)		((x) << 16)
@@ -73,8 +68,8 @@
 #define CFG_BRIDGE_SB_INIT			BIT(0)
 
 #define PCIE20_CAP				0x70
-#define PCIE20_CAP_LINK_CAPABILITIES		(PCIE20_CAP + 0xC)
-#define PCIE20_CAP_ACTIVE_STATE_LINK_PM_SUPPORT	(BIT(10) | BIT(11))
+#define PCIE20_DEVICE_CONTROL2_STATUS2		(PCIE20_CAP + PCI_EXP_DEVCTL2)
+#define PCIE20_CAP_LINK_CAPABILITIES		(PCIE20_CAP + PCI_EXP_LNKCAP)
 #define PCIE20_CAP_LINK_1			(PCIE20_CAP + 0x14)
 #define PCIE_CAP_LINK1_VAL			0x2FD7F
 
@@ -1095,15 +1090,15 @@ static int qcom_pcie_init_2_3_3(struct qcom_pcie *pcie)
 		pcie->parf + PCIE20_PARF_SYS_CTRL);
 	writel(0, pcie->parf + PCIE20_PARF_Q2A_FLUSH);
 
-	writel(CMD_BME_VAL, pci->dbi_base + PCIE20_COMMAND_STATUS);
+	writel(PCI_COMMAND_MASTER, pci->dbi_base + PCI_COMMAND);
 	writel(DBI_RO_WR_EN, pci->dbi_base + PCIE20_MISC_CONTROL_1_REG);
 	writel(PCIE_CAP_LINK1_VAL, pci->dbi_base + PCIE20_CAP_LINK_1);
 
 	val = readl(pci->dbi_base + PCIE20_CAP_LINK_CAPABILITIES);
-	val &= ~PCIE20_CAP_ACTIVE_STATE_LINK_PM_SUPPORT;
+	val &= ~PCI_EXP_LNKCAP_ASPMS;
 	writel(val, pci->dbi_base + PCIE20_CAP_LINK_CAPABILITIES);
 
-	writel(PCIE_CAP_CPL_TIMEOUT_DISABLE, pci->dbi_base +
+	writel(PCI_EXP_DEVCTL2_COMP_TMOUT_DIS, pci->dbi_base +
 		PCIE20_DEVICE_CONTROL2_STATUS2);
 
 	return 0;