提交 801c135c 编写于 作者: A Artem B. Bityutskiy 提交者: Frank Haverkamp

UBI: Unsorted Block Images

UBI (Latin: "where?") manages multiple logical volumes on a single
flash device, specifically supporting NAND flash devices. UBI provides
a flexible partitioning concept which still allows for wear-levelling
across the whole flash device.

In a sense, UBI may be compared to the Logical Volume Manager
(LVM). Whereas LVM maps logical sector numbers to physical HDD sector
numbers, UBI maps logical eraseblocks to physical eraseblocks.

More information may be found at
http://www.linux-mtd.infradead.org/doc/ubi.html

Partitioning/Re-partitioning

  An UBI volume occupies a certain number of erase blocks. This is
  limited by a configured maximum volume size, which could also be
  viewed as the partition size. Each individual UBI volume's size can
  be changed independently of the other UBI volumes, provided that the
  sum of all volume sizes doesn't exceed a certain limit.

  UBI supports dynamic volumes and static volumes. Static volumes are
  read-only and their contents are protected by CRC check sums.

Bad eraseblocks handling

  UBI transparently handles bad eraseblocks. When a physical
  eraseblock becomes bad, it is substituted by a good physical
  eraseblock, and the user does not even notice this.

Scrubbing

  On a NAND flash bit flips can occur on any write operation,
  sometimes also on read. If bit flips persist on the device, at first
  they can still be corrected by ECC, but once they accumulate,
  correction will become impossible. Thus it is best to actively scrub
  the affected eraseblock, by first copying it to a free eraseblock
  and then erasing the original. The UBI layer performs this type of
  scrubbing under the covers, transparently to the UBI volume users.

Erase Counts

  UBI maintains an erase count header per eraseblock. This frees
  higher-level layers (like file systems) from doing this and allows
  for centralized erase count management instead. The erase counts are
  used by the wear-levelling algorithm in the UBI layer. The algorithm
  itself is exchangeable.

Booting from NAND

  For booting directly from NAND flash the hardware must at least be
  capable of fetching and executing a small portion of the NAND
  flash. Some NAND flash controllers have this kind of support. They
  usually limit the window to a few kilobytes in erase block 0. This
  "initial program loader" (IPL) must then contain sufficient logic to
  load and execute the next boot phase.

  Due to bad eraseblocks, which may be randomly scattered over the
  flash device, it is problematic to store the "secondary program
  loader" (SPL) statically. Also, due to bit-flips it may become
  corrupted over time. UBI allows to solve this problem gracefully by
  storing the SPL in a small static UBI volume.

UBI volumes vs. static partitions

  UBI volumes are still very similar to static MTD partitions:

    * both consist of eraseblocks (logical eraseblocks in case of UBI
      volumes, and physical eraseblocks in case of static partitions;
    * both support three basic operations - read, write, erase.

  But UBI volumes have the following advantages over traditional
  static MTD partitions:

    * there are no eraseblock wear-leveling constraints in case of UBI
      volumes, so the user should not care about this;
    * there are no bit-flips and bad eraseblocks in case of UBI volumes.

  So, UBI volumes may be considered as flash devices with relaxed
  restrictions.

Where can it be found?

  Documentation, kernel code and applications can be found in the MTD
  gits.

What are the applications for?

  The applications help to create binary flash images for two purposes: pfi
  files (partial flash images) for in-system update of UBI volumes, and plain
  binary images, with or without OOB data in case of NAND, for a manufacturing
  step. Furthermore some tools are/and will be created that allow flash content
  analysis after a system has crashed..

Who did UBI?

  The original ideas, where UBI is based on, were developed by Andreas
  Arnez, Frank Haverkamp and Thomas Gleixner. Josh W. Boyer and some others
  were involved too. The implementation of the kernel layer was done by Artem
  B. Bityutskiy. The user-space applications and tools were written by Oliver
  Lohmann with contributions from Frank Haverkamp, Andreas Arnez, and Artem.
  Joern Engel contributed a patch which modifies JFFS2 so that it can be run on
  a UBI volume. Thomas Gleixner did modifications to the NAND layer. Alexander
  Schmidt made some testing work as well as core functionality improvements.
Signed-off-by: NArtem B. Bityutskiy <dedekind@linutronix.de>
Signed-off-by: NFrank Haverkamp <haver@vnet.ibm.com>
上级 de46c337
...@@ -292,5 +292,7 @@ source "drivers/mtd/nand/Kconfig" ...@@ -292,5 +292,7 @@ source "drivers/mtd/nand/Kconfig"
source "drivers/mtd/onenand/Kconfig" source "drivers/mtd/onenand/Kconfig"
source "drivers/mtd/ubi/Kconfig"
endmenu endmenu
...@@ -28,3 +28,5 @@ nftl-objs := nftlcore.o nftlmount.o ...@@ -28,3 +28,5 @@ nftl-objs := nftlcore.o nftlmount.o
inftl-objs := inftlcore.o inftlmount.o inftl-objs := inftlcore.o inftlmount.o
obj-y += chips/ maps/ devices/ nand/ onenand/ obj-y += chips/ maps/ devices/ nand/ onenand/
obj-$(CONFIG_MTD_UBI) += ubi/
# drivers/mtd/ubi/Kconfig
menu "UBI - Unsorted block images"
depends on MTD
config MTD_UBI
tristate "Enable UBI"
depends on MTD
select CRC32
help
UBI is a software layer above MTD layer which admits of LVM-like
logical volumes on top of MTD devices, hides some complexities of
flash chips like wear and bad blocks and provides some other useful
capabilities. Please, consult the MTD web site for more details
(www.linux-mtd.infradead.org).
config MTD_UBI_WL_THRESHOLD
int "UBI wear-leveling threshold"
default 4096
range 2 65536
depends on MTD_UBI
help
This parameter defines the maximum difference between the highest
erase counter value and the lowest erase counter value of eraseblocks
of UBI devices. When this threshold is exceeded, UBI starts performing
wear leveling by means of moving data from eraseblock with low erase
counter to eraseblocks with high erase counter. Leave the default
value if unsure.
config MTD_UBI_BEB_RESERVE
int "Percentage of reserved eraseblocks for bad eraseblocks handling"
default 1
range 0 25
depends on MTD_UBI
help
If the MTD device admits of bad eraseblocks (e.g. NAND flash), UBI
reserves some amount of physical eraseblocks to handle new bad
eraseblocks. For example, if a flash physical eraseblock becomes bad,
UBI uses these reserved physical eraseblocks to relocate the bad one.
This option specifies how many physical eraseblocks will be reserved
for bad eraseblock handling (percents of total number of good flash
eraseblocks). If the underlying flash does not admit of bad
eraseblocks (e.g. NOR flash), this value is ignored and nothing is
reserved. Leave the default value if unsure.
config MTD_UBI_GLUEBI
bool "Emulate MTD devices"
default n
depends on MTD_UBI
help
This option enables MTD devices emulation on top of UBI volumes: for
each UBI volumes an MTD device is created, and all I/O to this MTD
device is redirected to the UBI volume. This is handy to make
MTD-oriented software (like JFFS2) work on top of UBI. Do not enable
this if no legacy software will be used.
source "drivers/mtd/ubi/Kconfig.debug"
endmenu
comment "UBI debugging options"
depends on MTD_UBI
config MTD_UBI_DEBUG
bool "UBI debugging"
depends on SYSFS
depends on MTD_UBI
select DEBUG_FS
select KALLSYMS_ALL
help
This option enables UBI debugging.
config MTD_UBI_DEBUG_MSG
bool "UBI debugging messages"
depends on MTD_UBI_DEBUG
default n
help
This option enables UBI debugging messages.
config MTD_UBI_DEBUG_PARANOID
bool "Extra self-checks"
default n
depends on MTD_UBI_DEBUG
help
This option enables extra checks in UBI code. Note this slows UBI down
significantly.
config MTD_UBI_DEBUG_DISABLE_BGT
bool "Do not enable the UBI background thread"
depends on MTD_UBI_DEBUG
default n
help
This option switches the background thread off by default. The thread
may be also be enabled/disabled via UBI sysfs.
config MTD_UBI_DEBUG_USERSPACE_IO
bool "Direct user-space write/erase support"
default n
depends on MTD_UBI_DEBUG
help
By default, users cannot directly write and erase individual
eraseblocks of dynamic volumes, and have to use update operation
instead. This option enables this capability - it is very useful for
debugging and testing.
config MTD_UBI_DEBUG_EMULATE_BITFLIPS
bool "Emulate flash bit-flips"
depends on MTD_UBI_DEBUG
default n
help
This option emulates bit-flips with probability 1/50, which in turn
causes scrubbing. Useful for debugging and stressing UBI.
config MTD_UBI_DEBUG_EMULATE_WRITE_FAILURES
bool "Emulate flash write failures"
depends on MTD_UBI_DEBUG
default n
help
This option emulates write failures with probability 1/100. Useful for
debugging and testing how UBI handlines errors.
config MTD_UBI_DEBUG_EMULATE_ERASE_FAILURES
bool "Emulate flash erase failures"
depends on MTD_UBI_DEBUG
default n
help
This option emulates erase failures with probability 1/100. Useful for
debugging and testing how UBI handlines errors.
menu "Additional UBI debugging messages"
depends on MTD_UBI_DEBUG
config MTD_UBI_DEBUG_MSG_BLD
bool "Additional UBI initialization and build messages"
default n
depends on MTD_UBI_DEBUG
help
This option enables detailed UBI initialization and device build
debugging messages.
config MTD_UBI_DEBUG_MSG_EBA
bool "Eraseblock association unit messages"
default n
depends on MTD_UBI_DEBUG
help
This option enables debugging messages from the UBI eraseblock
association unit.
config MTD_UBI_DEBUG_MSG_WL
bool "Wear-leveling unit messages"
default n
depends on MTD_UBI_DEBUG
help
This option enables debugging messages from the UBI wear-leveling
unit.
config MTD_UBI_DEBUG_MSG_IO
bool "Input/output unit messages"
default n
depends on MTD_UBI_DEBUG
help
This option enables debugging messages from the UBI input/output unit.
endmenu # UBI debugging messages
obj-$(CONFIG_MTD_UBI) += ubi.o
ubi-y += vtbl.o vmt.o upd.o build.o cdev.o kapi.o eba.o io.o wl.o scan.o
ubi-y += misc.o
ubi-$(CONFIG_MTD_UBI_DEBUG) += debug.o
ubi-$(CONFIG_MTD_UBI_GLUEBI) += gluebi.o
此差异已折叠。
/*
* Copyright (c) International Business Machines Corp., 2006
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See
* the GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
* Author: Artem Bityutskiy (Битюцкий Артём)
*/
/*
* This file includes implementation of UBI character device operations.
*
* There are two kinds of character devices in UBI: UBI character devices and
* UBI volume character devices. UBI character devices allow users to
* manipulate whole volumes: create, remove, and re-size them. Volume character
* devices provide volume I/O capabilities.
*
* Major and minor numbers are assigned dynamically to both UBI and volume
* character devices.
*/
#include <linux/module.h>
#include <linux/stat.h>
#include <linux/ioctl.h>
#include <linux/capability.h>
#include <mtd/ubi-user.h>
#include <asm/uaccess.h>
#include <asm/div64.h>
#include "ubi.h"
/*
* Maximum sequence numbers of UBI and volume character device IOCTLs (direct
* logical eraseblock erase is a debug-only feature).
*/
#define UBI_CDEV_IOC_MAX_SEQ 2
#ifndef CONFIG_MTD_UBI_DEBUG_USERSPACE_IO
#define VOL_CDEV_IOC_MAX_SEQ 1
#else
#define VOL_CDEV_IOC_MAX_SEQ 2
#endif
/**
* major_to_device - get UBI device object by character device major number.
* @major: major number
*
* This function returns a pointer to the UBI device object.
*/
static struct ubi_device *major_to_device(int major)
{
int i;
for (i = 0; i < ubi_devices_cnt; i++)
if (ubi_devices[i] && ubi_devices[i]->major == major)
return ubi_devices[i];
BUG();
}
/**
* get_exclusive - get exclusive access to an UBI volume.
* @desc: volume descriptor
*
* This function changes UBI volume open mode to "exclusive". Returns previous
* mode value (positive integer) in case of success and a negative error code
* in case of failure.
*/
static int get_exclusive(struct ubi_volume_desc *desc)
{
int users, err;
struct ubi_volume *vol = desc->vol;
spin_lock(&vol->ubi->volumes_lock);
users = vol->readers + vol->writers + vol->exclusive;
ubi_assert(users > 0);
if (users > 1) {
dbg_err("%d users for volume %d", users, vol->vol_id);
err = -EBUSY;
} else {
vol->readers = vol->writers = 0;
vol->exclusive = 1;
err = desc->mode;
desc->mode = UBI_EXCLUSIVE;
}
spin_unlock(&vol->ubi->volumes_lock);
return err;
}
/**
* revoke_exclusive - revoke exclusive mode.
* @desc: volume descriptor
* @mode: new mode to switch to
*/
static void revoke_exclusive(struct ubi_volume_desc *desc, int mode)
{
struct ubi_volume *vol = desc->vol;
spin_lock(&vol->ubi->volumes_lock);
ubi_assert(vol->readers == 0 && vol->writers == 0);
ubi_assert(vol->exclusive == 1 && desc->mode == UBI_EXCLUSIVE);
vol->exclusive = 0;
if (mode == UBI_READONLY)
vol->readers = 1;
else if (mode == UBI_READWRITE)
vol->writers = 1;
else
vol->exclusive = 1;
spin_unlock(&vol->ubi->volumes_lock);
desc->mode = mode;
}
static int vol_cdev_open(struct inode *inode, struct file *file)
{
struct ubi_volume_desc *desc;
const struct ubi_device *ubi = major_to_device(imajor(inode));
int vol_id = iminor(inode) - 1;
int mode;
if (file->f_mode & FMODE_WRITE)
mode = UBI_READWRITE;
else
mode = UBI_READONLY;
dbg_msg("open volume %d, mode %d", vol_id, mode);
desc = ubi_open_volume(ubi->ubi_num, vol_id, mode);
if (IS_ERR(desc))
return PTR_ERR(desc);
file->private_data = desc;
return 0;
}
static int vol_cdev_release(struct inode *inode, struct file *file)
{
struct ubi_volume_desc *desc = file->private_data;
struct ubi_volume *vol = desc->vol;
dbg_msg("release volume %d, mode %d", vol->vol_id, desc->mode);
if (vol->updating) {
ubi_warn("update of volume %d not finished, volume is damaged",
vol->vol_id);
vol->updating = 0;
kfree(vol->upd_buf);
}
ubi_close_volume(desc);
return 0;
}
static loff_t vol_cdev_llseek(struct file *file, loff_t offset, int origin)
{
struct ubi_volume_desc *desc = file->private_data;
struct ubi_volume *vol = desc->vol;
loff_t new_offset;
if (vol->updating) {
/* Update is in progress, seeking is prohibited */
dbg_err("updating");
return -EBUSY;
}
switch (origin) {
case 0: /* SEEK_SET */
new_offset = offset;
break;
case 1: /* SEEK_CUR */
new_offset = file->f_pos + offset;
break;
case 2: /* SEEK_END */
new_offset = vol->used_bytes + offset;
break;
default:
return -EINVAL;
}
if (new_offset < 0 || new_offset > vol->used_bytes) {
dbg_err("bad seek %lld", new_offset);
return -EINVAL;
}
dbg_msg("seek volume %d, offset %lld, origin %d, new offset %lld",
vol->vol_id, offset, origin, new_offset);
file->f_pos = new_offset;
return new_offset;
}
static ssize_t vol_cdev_read(struct file *file, __user char *buf, size_t count,
loff_t *offp)
{
struct ubi_volume_desc *desc = file->private_data;
struct ubi_volume *vol = desc->vol;
struct ubi_device *ubi = vol->ubi;
int err, lnum, off, len, vol_id = desc->vol->vol_id, tbuf_size;
size_t count_save = count;
void *tbuf;
uint64_t tmp;
dbg_msg("read %zd bytes from offset %lld of volume %d",
count, *offp, vol_id);
if (vol->updating) {
dbg_err("updating");
return -EBUSY;
}
if (vol->upd_marker) {
dbg_err("damaged volume, update marker is set");
return -EBADF;
}
if (*offp == vol->used_bytes || count == 0)
return 0;
if (vol->corrupted)
dbg_msg("read from corrupted volume %d", vol_id);
if (*offp + count > vol->used_bytes)
count_save = count = vol->used_bytes - *offp;
tbuf_size = vol->usable_leb_size;
if (count < tbuf_size)
tbuf_size = ALIGN(count, ubi->min_io_size);
tbuf = kmalloc(tbuf_size, GFP_KERNEL);
if (!tbuf)
return -ENOMEM;
len = count > tbuf_size ? tbuf_size : count;
tmp = *offp;
off = do_div(tmp, vol->usable_leb_size);
lnum = tmp;
do {
cond_resched();
if (off + len >= vol->usable_leb_size)
len = vol->usable_leb_size - off;
err = ubi_eba_read_leb(ubi, vol_id, lnum, tbuf, off, len, 0);
if (err)
break;
off += len;
if (off == vol->usable_leb_size) {
lnum += 1;
off -= vol->usable_leb_size;
}
count -= len;
*offp += len;
err = copy_to_user(buf, tbuf, len);
if (err) {
err = -EFAULT;
break;
}
buf += len;
len = count > tbuf_size ? tbuf_size : count;
} while (count);
kfree(tbuf);
return err ? err : count_save - count;
}
#ifdef CONFIG_MTD_UBI_DEBUG_USERSPACE_IO
/*
* This function allows to directly write to dynamic UBI volumes, without
* issuing the volume update operation. Available only as a debugging feature.
* Very useful for testing UBI.
*/
static ssize_t vol_cdev_direct_write(struct file *file, const char __user *buf,
size_t count, loff_t *offp)
{
struct ubi_volume_desc *desc = file->private_data;
struct ubi_volume *vol = desc->vol;
struct ubi_device *ubi = vol->ubi;
int lnum, off, len, tbuf_size, vol_id = vol->vol_id, err = 0;
size_t count_save = count;
char *tbuf;
uint64_t tmp;
dbg_msg("requested: write %zd bytes to offset %lld of volume %u",
count, *offp, desc->vol->vol_id);
if (vol->vol_type == UBI_STATIC_VOLUME)
return -EROFS;
tmp = *offp;
off = do_div(tmp, vol->usable_leb_size);
lnum = tmp;
if (off % ubi->min_io_size) {
dbg_err("unaligned position");
return -EINVAL;
}
if (*offp + count > vol->used_bytes)
count_save = count = vol->used_bytes - *offp;
/* We can write only in fractions of the minimum I/O unit */
if (count % ubi->min_io_size) {
dbg_err("unaligned write length");
return -EINVAL;
}
tbuf_size = vol->usable_leb_size;
if (count < tbuf_size)
tbuf_size = ALIGN(count, ubi->min_io_size);
tbuf = kmalloc(tbuf_size, GFP_KERNEL);
if (!tbuf)
return -ENOMEM;
len = count > tbuf_size ? tbuf_size : count;
while (count) {
cond_resched();
if (off + len >= vol->usable_leb_size)
len = vol->usable_leb_size - off;
err = copy_from_user(tbuf, buf, len);
if (err) {
err = -EFAULT;
break;
}
err = ubi_eba_write_leb(ubi, vol_id, lnum, tbuf, off, len,
UBI_UNKNOWN);
if (err)
break;
off += len;
if (off == vol->usable_leb_size) {
lnum += 1;
off -= vol->usable_leb_size;
}
count -= len;
*offp += len;
buf += len;
len = count > tbuf_size ? tbuf_size : count;
}
kfree(tbuf);
return err ? err : count_save - count;
}
#else
#define vol_cdev_direct_write(file, buf, count, offp) -EPERM
#endif /* CONFIG_MTD_UBI_DEBUG_USERSPACE_IO */
static ssize_t vol_cdev_write(struct file *file, const char __user *buf,
size_t count, loff_t *offp)
{
int err = 0;
struct ubi_volume_desc *desc = file->private_data;
struct ubi_volume *vol = desc->vol;
struct ubi_device *ubi = vol->ubi;
if (!vol->updating)
return vol_cdev_direct_write(file, buf, count, offp);
err = ubi_more_update_data(ubi, vol->vol_id, buf, count);
if (err < 0) {
ubi_err("cannot write %zd bytes of update data", count);
return err;
}
if (err) {
/*
* Update is finished, @err contains number of actually written
* bytes now.
*/
count = err;
err = ubi_check_volume(ubi, vol->vol_id);
if (err < 0)
return err;
if (err) {
ubi_warn("volume %d on UBI device %d is corrupted",
vol->vol_id, ubi->ubi_num);
vol->corrupted = 1;
}
vol->checked = 1;
revoke_exclusive(desc, UBI_READWRITE);
}
*offp += count;
return count;
}
static int vol_cdev_ioctl(struct inode *inode, struct file *file,
unsigned int cmd, unsigned long arg)
{
int err = 0;
struct ubi_volume_desc *desc = file->private_data;
struct ubi_volume *vol = desc->vol;
struct ubi_device *ubi = vol->ubi;
void __user *argp = (void __user *)arg;
if (_IOC_NR(cmd) > VOL_CDEV_IOC_MAX_SEQ ||
_IOC_TYPE(cmd) != UBI_VOL_IOC_MAGIC)
return -ENOTTY;
if (_IOC_DIR(cmd) && _IOC_READ)
err = !access_ok(VERIFY_WRITE, argp, _IOC_SIZE(cmd));
else if (_IOC_DIR(cmd) && _IOC_WRITE)
err = !access_ok(VERIFY_READ, argp, _IOC_SIZE(cmd));
if (err)
return -EFAULT;
switch (cmd) {
/* Volume update command */
case UBI_IOCVOLUP:
{
int64_t bytes, rsvd_bytes;
if (!capable(CAP_SYS_RESOURCE)) {
err = -EPERM;
break;
}
err = copy_from_user(&bytes, argp, sizeof(int64_t));
if (err) {
err = -EFAULT;
break;
}
if (desc->mode == UBI_READONLY) {
err = -EROFS;
break;
}
rsvd_bytes = vol->reserved_pebs * (ubi->leb_size-vol->data_pad);
if (bytes < 0 || bytes > rsvd_bytes) {
err = -EINVAL;
break;
}
err = get_exclusive(desc);
if (err < 0)
break;
err = ubi_start_update(ubi, vol->vol_id, bytes);
if (bytes == 0)
revoke_exclusive(desc, UBI_READWRITE);
file->f_pos = 0;
break;
}
#ifdef CONFIG_MTD_UBI_DEBUG_USERSPACE_IO
/* Logical eraseblock erasure command */
case UBI_IOCEBER:
{
int32_t lnum;
err = __get_user(lnum, (__user int32_t *)argp);
if (err) {
err = -EFAULT;
break;
}
if (desc->mode == UBI_READONLY) {
err = -EROFS;
break;
}
if (lnum < 0 || lnum >= vol->reserved_pebs) {
err = -EINVAL;
break;
}
if (vol->vol_type != UBI_DYNAMIC_VOLUME) {
err = -EROFS;
break;
}
dbg_msg("erase LEB %d:%d", vol->vol_id, lnum);
err = ubi_eba_unmap_leb(ubi, vol->vol_id, lnum);
if (err)
break;
err = ubi_wl_flush(ubi);
break;
}
#endif
default:
err = -ENOTTY;
break;
}
return err;
}
/**
* verify_mkvol_req - verify volume creation request.
* @ubi: UBI device description object
* @req: the request to check
*
* This function zero if the request is correct, and %-EINVAL if not.
*/
static int verify_mkvol_req(const struct ubi_device *ubi,
const struct ubi_mkvol_req *req)
{
int n, err = -EINVAL;
if (req->bytes < 0 || req->alignment < 0 || req->vol_type < 0 ||
req->name_len < 0)
goto bad;
if ((req->vol_id < 0 || req->vol_id >= ubi->vtbl_slots) &&
req->vol_id != UBI_VOL_NUM_AUTO)
goto bad;
if (req->alignment == 0)
goto bad;
if (req->bytes == 0)
goto bad;
if (req->vol_type != UBI_DYNAMIC_VOLUME &&
req->vol_type != UBI_STATIC_VOLUME)
goto bad;
if (req->alignment > ubi->leb_size)
goto bad;
n = req->alignment % ubi->min_io_size;
if (req->alignment != 1 && n)
goto bad;
if (req->name_len > UBI_VOL_NAME_MAX) {
err = -ENAMETOOLONG;
goto bad;
}
return 0;
bad:
dbg_err("bad volume creation request");
ubi_dbg_dump_mkvol_req(req);
return err;
}
/**
* verify_rsvol_req - verify volume re-size request.
* @ubi: UBI device description object
* @req: the request to check
*
* This function returns zero if the request is correct, and %-EINVAL if not.
*/
static int verify_rsvol_req(const struct ubi_device *ubi,
const struct ubi_rsvol_req *req)
{
if (req->bytes <= 0)
return -EINVAL;
if (req->vol_id < 0 || req->vol_id >= ubi->vtbl_slots)
return -EINVAL;
return 0;
}
static int ubi_cdev_ioctl(struct inode *inode, struct file *file,
unsigned int cmd, unsigned long arg)
{
int err = 0;
struct ubi_device *ubi;
struct ubi_volume_desc *desc;
void __user *argp = (void __user *)arg;
if (_IOC_NR(cmd) > UBI_CDEV_IOC_MAX_SEQ ||
_IOC_TYPE(cmd) != UBI_IOC_MAGIC)
return -ENOTTY;
if (_IOC_DIR(cmd) && _IOC_READ)
err = !access_ok(VERIFY_WRITE, argp, _IOC_SIZE(cmd));
else if (_IOC_DIR(cmd) && _IOC_WRITE)
err = !access_ok(VERIFY_READ, argp, _IOC_SIZE(cmd));
if (err)
return -EFAULT;
if (!capable(CAP_SYS_RESOURCE))
return -EPERM;
ubi = major_to_device(imajor(inode));
if (IS_ERR(ubi))
return PTR_ERR(ubi);
switch (cmd) {
/* Create volume command */
case UBI_IOCMKVOL:
{
struct ubi_mkvol_req req;
dbg_msg("create volume");
err = __copy_from_user(&req, argp,
sizeof(struct ubi_mkvol_req));
if (err) {
err = -EFAULT;
break;
}
err = verify_mkvol_req(ubi, &req);
if (err)
break;
req.name[req.name_len] = '\0';
err = ubi_create_volume(ubi, &req);
if (err)
break;
err = __put_user(req.vol_id, (__user int32_t *)argp);
if (err)
err = -EFAULT;
break;
}
/* Remove volume command */
case UBI_IOCRMVOL:
{
int vol_id;
dbg_msg("remove volume");
err = __get_user(vol_id, (__user int32_t *)argp);
if (err) {
err = -EFAULT;
break;
}
desc = ubi_open_volume(ubi->ubi_num, vol_id, UBI_EXCLUSIVE);
if (IS_ERR(desc)) {
err = PTR_ERR(desc);
break;
}
err = ubi_remove_volume(desc);
if (err)
ubi_close_volume(desc);
break;
}
/* Re-size volume command */
case UBI_IOCRSVOL:
{
int pebs;
uint64_t tmp;
struct ubi_rsvol_req req;
dbg_msg("re-size volume");
err = __copy_from_user(&req, argp,
sizeof(struct ubi_rsvol_req));
if (err) {
err = -EFAULT;
break;
}
err = verify_rsvol_req(ubi, &req);
if (err)
break;
desc = ubi_open_volume(ubi->ubi_num, req.vol_id, UBI_EXCLUSIVE);
if (IS_ERR(desc)) {
err = PTR_ERR(desc);
break;
}
tmp = req.bytes;
pebs = !!do_div(tmp, desc->vol->usable_leb_size);
pebs += tmp;
err = ubi_resize_volume(desc, pebs);
ubi_close_volume(desc);
break;
}
default:
err = -ENOTTY;
break;
}
return err;
}
/* UBI character device operations */
struct file_operations ubi_cdev_operations = {
.owner = THIS_MODULE,
.ioctl = ubi_cdev_ioctl,
.llseek = no_llseek
};
/* UBI volume character device operations */
struct file_operations ubi_vol_cdev_operations = {
.owner = THIS_MODULE,
.open = vol_cdev_open,
.release = vol_cdev_release,
.llseek = vol_cdev_llseek,
.read = vol_cdev_read,
.write = vol_cdev_write,
.ioctl = vol_cdev_ioctl
};
/*
* Copyright (c) International Business Machines Corp., 2006
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See
* the GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
* Author: Artem Bityutskiy (Битюцкий Артём)
*/
/*
* Here we keep all the UBI debugging stuff which should normally be disabled
* and compiled-out, but it is extremely helpful when hunting bugs or doing big
* changes.
*/
#ifdef CONFIG_MTD_UBI_DEBUG_MSG
#include "ubi.h"
/**
* ubi_dbg_dump_ec_hdr - dump an erase counter header.
* @ec_hdr: the erase counter header to dump
*/
void ubi_dbg_dump_ec_hdr(const struct ubi_ec_hdr *ec_hdr)
{
dbg_msg("erase counter header dump:");
dbg_msg("magic %#08x", ubi32_to_cpu(ec_hdr->magic));
dbg_msg("version %d", (int)ec_hdr->version);
dbg_msg("ec %llu", (long long)ubi64_to_cpu(ec_hdr->ec));
dbg_msg("vid_hdr_offset %d", ubi32_to_cpu(ec_hdr->vid_hdr_offset));
dbg_msg("data_offset %d", ubi32_to_cpu(ec_hdr->data_offset));
dbg_msg("hdr_crc %#08x", ubi32_to_cpu(ec_hdr->hdr_crc));
dbg_msg("erase counter header hexdump:");
ubi_dbg_hexdump(ec_hdr, UBI_EC_HDR_SIZE);
}
/**
* ubi_dbg_dump_vid_hdr - dump a volume identifier header.
* @vid_hdr: the volume identifier header to dump
*/
void ubi_dbg_dump_vid_hdr(const struct ubi_vid_hdr *vid_hdr)
{
dbg_msg("volume identifier header dump:");
dbg_msg("magic %08x", ubi32_to_cpu(vid_hdr->magic));
dbg_msg("version %d", (int)vid_hdr->version);
dbg_msg("vol_type %d", (int)vid_hdr->vol_type);
dbg_msg("copy_flag %d", (int)vid_hdr->copy_flag);
dbg_msg("compat %d", (int)vid_hdr->compat);
dbg_msg("vol_id %d", ubi32_to_cpu(vid_hdr->vol_id));
dbg_msg("lnum %d", ubi32_to_cpu(vid_hdr->lnum));
dbg_msg("leb_ver %u", ubi32_to_cpu(vid_hdr->leb_ver));
dbg_msg("data_size %d", ubi32_to_cpu(vid_hdr->data_size));
dbg_msg("used_ebs %d", ubi32_to_cpu(vid_hdr->used_ebs));
dbg_msg("data_pad %d", ubi32_to_cpu(vid_hdr->data_pad));
dbg_msg("sqnum %llu",
(unsigned long long)ubi64_to_cpu(vid_hdr->sqnum));
dbg_msg("hdr_crc %08x", ubi32_to_cpu(vid_hdr->hdr_crc));
dbg_msg("volume identifier header hexdump:");
}
/**
* ubi_dbg_dump_vol_info- dump volume information.
* @vol: UBI volume description object
*/
void ubi_dbg_dump_vol_info(const struct ubi_volume *vol)
{
dbg_msg("volume information dump:");
dbg_msg("vol_id %d", vol->vol_id);
dbg_msg("reserved_pebs %d", vol->reserved_pebs);
dbg_msg("alignment %d", vol->alignment);
dbg_msg("data_pad %d", vol->data_pad);
dbg_msg("vol_type %d", vol->vol_type);
dbg_msg("name_len %d", vol->name_len);
dbg_msg("usable_leb_size %d", vol->usable_leb_size);
dbg_msg("used_ebs %d", vol->used_ebs);
dbg_msg("used_bytes %lld", vol->used_bytes);
dbg_msg("last_eb_bytes %d", vol->last_eb_bytes);
dbg_msg("corrupted %d", vol->corrupted);
dbg_msg("upd_marker %d", vol->upd_marker);
if (vol->name_len <= UBI_VOL_NAME_MAX &&
strnlen(vol->name, vol->name_len + 1) == vol->name_len) {
dbg_msg("name %s", vol->name);
} else {
dbg_msg("the 1st 5 characters of the name: %c%c%c%c%c",
vol->name[0], vol->name[1], vol->name[2],
vol->name[3], vol->name[4]);
}
}
/**
* ubi_dbg_dump_vtbl_record - dump a &struct ubi_vtbl_record object.
* @r: the object to dump
* @idx: volume table index
*/
void ubi_dbg_dump_vtbl_record(const struct ubi_vtbl_record *r, int idx)
{
int name_len = ubi16_to_cpu(r->name_len);
dbg_msg("volume table record %d dump:", idx);
dbg_msg("reserved_pebs %d", ubi32_to_cpu(r->reserved_pebs));
dbg_msg("alignment %d", ubi32_to_cpu(r->alignment));
dbg_msg("data_pad %d", ubi32_to_cpu(r->data_pad));
dbg_msg("vol_type %d", (int)r->vol_type);
dbg_msg("upd_marker %d", (int)r->upd_marker);
dbg_msg("name_len %d", name_len);
if (r->name[0] == '\0') {
dbg_msg("name NULL");
return;
}
if (name_len <= UBI_VOL_NAME_MAX &&
strnlen(&r->name[0], name_len + 1) == name_len) {
dbg_msg("name %s", &r->name[0]);
} else {
dbg_msg("1st 5 characters of the name: %c%c%c%c%c",
r->name[0], r->name[1], r->name[2], r->name[3],
r->name[4]);
}
dbg_msg("crc %#08x", ubi32_to_cpu(r->crc));
}
/**
* ubi_dbg_dump_sv - dump a &struct ubi_scan_volume object.
* @sv: the object to dump
*/
void ubi_dbg_dump_sv(const struct ubi_scan_volume *sv)
{
dbg_msg("volume scanning information dump:");
dbg_msg("vol_id %d", sv->vol_id);
dbg_msg("highest_lnum %d", sv->highest_lnum);
dbg_msg("leb_count %d", sv->leb_count);
dbg_msg("compat %d", sv->compat);
dbg_msg("vol_type %d", sv->vol_type);
dbg_msg("used_ebs %d", sv->used_ebs);
dbg_msg("last_data_size %d", sv->last_data_size);
dbg_msg("data_pad %d", sv->data_pad);
}
/**
* ubi_dbg_dump_seb - dump a &struct ubi_scan_leb object.
* @seb: the object to dump
* @type: object type: 0 - not corrupted, 1 - corrupted
*/
void ubi_dbg_dump_seb(const struct ubi_scan_leb *seb, int type)
{
dbg_msg("eraseblock scanning information dump:");
dbg_msg("ec %d", seb->ec);
dbg_msg("pnum %d", seb->pnum);
if (type == 0) {
dbg_msg("lnum %d", seb->lnum);
dbg_msg("scrub %d", seb->scrub);
dbg_msg("sqnum %llu", seb->sqnum);
dbg_msg("leb_ver %u", seb->leb_ver);
}
}
/**
* ubi_dbg_dump_mkvol_req - dump a &struct ubi_mkvol_req object.
* @req: the object to dump
*/
void ubi_dbg_dump_mkvol_req(const struct ubi_mkvol_req *req)
{
char nm[17];
dbg_msg("volume creation request dump:");
dbg_msg("vol_id %d", req->vol_id);
dbg_msg("alignment %d", req->alignment);
dbg_msg("bytes %lld", (long long)req->bytes);
dbg_msg("vol_type %d", req->vol_type);
dbg_msg("name_len %d", req->name_len);
memcpy(nm, req->name, 16);
nm[16] = 0;
dbg_msg("the 1st 16 characters of the name: %s", nm);
}
#define BYTES_PER_LINE 32
/**
* ubi_dbg_hexdump - dump a buffer.
* @ptr: the buffer to dump
* @size: buffer size which must be multiple of 4 bytes
*/
void ubi_dbg_hexdump(const void *ptr, int size)
{
int i, k = 0, rows, columns;
const uint8_t *p = ptr;
size = ALIGN(size, 4);
rows = size/BYTES_PER_LINE + size % BYTES_PER_LINE;
for (i = 0; i < rows; i++) {
int j;
cond_resched();
columns = min(size - k, BYTES_PER_LINE) / 4;
if (columns == 0)
break;
printk(KERN_DEBUG "%5d: ", i * BYTES_PER_LINE);
for (j = 0; j < columns; j++) {
int n, N;
N = size - k > 4 ? 4 : size - k;
for (n = 0; n < N; n++)
printk("%02x", p[k++]);
printk(" ");
}
printk("\n");
}
}
#endif /* CONFIG_MTD_UBI_DEBUG_MSG */
/*
* Copyright (c) International Business Machines Corp., 2006
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See
* the GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
* Author: Artem Bityutskiy (Битюцкий Артём)
*/
#ifndef __UBI_DEBUG_H__
#define __UBI_DEBUG_H__
#ifdef CONFIG_MTD_UBI_DEBUG
#include <linux/random.h>
#define ubi_assert(expr) BUG_ON(!(expr))
#define dbg_err(fmt, ...) ubi_err(fmt, ##__VA_ARGS__)
#else
#define ubi_assert(expr) ({})
#define dbg_err(fmt, ...) ({})
#endif
#ifdef CONFIG_MTD_UBI_DEBUG_DISABLE_BGT
#define DBG_DISABLE_BGT 1
#else
#define DBG_DISABLE_BGT 0
#endif
#ifdef CONFIG_MTD_UBI_DEBUG_MSG
/* Generic debugging message */
#define dbg_msg(fmt, ...) \
printk(KERN_DEBUG "UBI DBG: %s: " fmt "\n", __FUNCTION__, ##__VA_ARGS__)
#define ubi_dbg_dump_stack() dump_stack()
struct ubi_ec_hdr;
struct ubi_vid_hdr;
struct ubi_volume;
struct ubi_vtbl_record;
struct ubi_scan_volume;
struct ubi_scan_leb;
struct ubi_mkvol_req;
void ubi_dbg_print(int type, const char *func, const char *fmt, ...);
void ubi_dbg_dump_ec_hdr(const struct ubi_ec_hdr *ec_hdr);
void ubi_dbg_dump_vid_hdr(const struct ubi_vid_hdr *vid_hdr);
void ubi_dbg_dump_vol_info(const struct ubi_volume *vol);
void ubi_dbg_dump_vtbl_record(const struct ubi_vtbl_record *r, int idx);
void ubi_dbg_dump_sv(const struct ubi_scan_volume *sv);
void ubi_dbg_dump_seb(const struct ubi_scan_leb *seb, int type);
void ubi_dbg_dump_mkvol_req(const struct ubi_mkvol_req *req);
void ubi_dbg_hexdump(const void *buf, int size);
#else
#define dbg_msg(fmt, ...) ({})
#define ubi_dbg_dump_stack() ({})
#define ubi_dbg_print(func, fmt, ...) ({})
#define ubi_dbg_dump_ec_hdr(ec_hdr) ({})
#define ubi_dbg_dump_vid_hdr(vid_hdr) ({})
#define ubi_dbg_dump_vol_info(vol) ({})
#define ubi_dbg_dump_vtbl_record(r, idx) ({})
#define ubi_dbg_dump_sv(sv) ({})
#define ubi_dbg_dump_seb(seb, type) ({})
#define ubi_dbg_dump_mkvol_req(req) ({})
#define ubi_dbg_hexdump(buf, size) ({})
#endif /* CONFIG_MTD_UBI_DEBUG_MSG */
#ifdef CONFIG_MTD_UBI_DEBUG_MSG_EBA
/* Messages from the eraseblock association unit */
#define dbg_eba(fmt, ...) \
printk(KERN_DEBUG "UBI DBG eba: %s: " fmt "\n", __FUNCTION__, \
##__VA_ARGS__)
#else
#define dbg_eba(fmt, ...) ({})
#endif
#ifdef CONFIG_MTD_UBI_DEBUG_MSG_WL
/* Messages from the wear-leveling unit */
#define dbg_wl(fmt, ...) \
printk(KERN_DEBUG "UBI DBG wl: %s: " fmt "\n", __FUNCTION__, \
##__VA_ARGS__)
#else
#define dbg_wl(fmt, ...) ({})
#endif
#ifdef CONFIG_MTD_UBI_DEBUG_MSG_IO
/* Messages from the input/output unit */
#define dbg_io(fmt, ...) \
printk(KERN_DEBUG "UBI DBG io: %s: " fmt "\n", __FUNCTION__, \
##__VA_ARGS__)
#else
#define dbg_io(fmt, ...) ({})
#endif
#ifdef CONFIG_MTD_UBI_DEBUG_MSG_BLD
/* Initialization and build messages */
#define dbg_bld(fmt, ...) \
printk(KERN_DEBUG "UBI DBG bld: %s: " fmt "\n", __FUNCTION__, \
##__VA_ARGS__)
#else
#define dbg_bld(fmt, ...) ({})
#endif
#ifdef CONFIG_MTD_UBI_DEBUG_EMULATE_BITFLIPS
/**
* ubi_dbg_is_bitflip - if it is time to emulate a bit-flip.
*
* Returns non-zero if a bit-flip should be emulated, otherwise returns zero.
*/
static inline int ubi_dbg_is_bitflip(void)
{
return !(random32() % 200);
}
#else
#define ubi_dbg_is_bitflip() 0
#endif
#ifdef CONFIG_MTD_UBI_DEBUG_EMULATE_WRITE_FAILURES
/**
* ubi_dbg_is_write_failure - if it is time to emulate a write failure.
*
* Returns non-zero if a write failure should be emulated, otherwise returns
* zero.
*/
static inline int ubi_dbg_is_write_failure(void)
{
return !(random32() % 500);
}
#else
#define ubi_dbg_is_write_failure() 0
#endif
#ifdef CONFIG_MTD_UBI_DEBUG_EMULATE_ERASE_FAILURES
/**
* ubi_dbg_is_erase_failure - if its time to emulate an erase failure.
*
* Returns non-zero if an erase failure should be emulated, otherwise returns
* zero.
*/
static inline int ubi_dbg_is_erase_failure(void)
{
return !(random32() % 400);
}
#else
#define ubi_dbg_is_erase_failure() 0
#endif
#endif /* !__UBI_DEBUG_H__ */
此差异已折叠。
/*
* Copyright (c) International Business Machines Corp., 2006
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See
* the GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
* Author: Artem Bityutskiy (Битюцкий Артём), Joern Engel
*/
/*
* This file includes implementation of fake MTD devices for each UBI volume.
* This sounds strange, but it is in fact quite useful to make MTD-oriented
* software (including all the legacy software) to work on top of UBI.
*
* Gluebi emulates MTD devices of "MTD_UBIVOLUME" type. Their minimal I/O unit
* size (mtd->writesize) is equivalent to the UBI minimal I/O unit. The
* eraseblock size is equivalent to the logical eraseblock size of the volume.
*/
#include <asm/div64.h>
#include "ubi.h"
/**
* gluebi_get_device - get MTD device reference.
* @mtd: the MTD device description object
*
* This function is called every time the MTD device is being opened and
* implements the MTD get_device() operation. Returns zero in case of success
* and a negative error code in case of failure.
*/
static int gluebi_get_device(struct mtd_info *mtd)
{
struct ubi_volume *vol;
vol = container_of(mtd, struct ubi_volume, gluebi_mtd);
/*
* We do not introduce locks for gluebi reference count because the
* get_device()/put_device() calls are already serialized at MTD.
*/
if (vol->gluebi_refcount > 0) {
/*
* The MTD device is already referenced and this is just one
* more reference. MTD allows many users to open the same
* volume simultaneously and do not distinguish between
* readers/writers/exclusive openers as UBI does. So we do not
* open the UBI volume again - just increase the reference
* counter and return.
*/
vol->gluebi_refcount += 1;
return 0;
}
/*
* This is the first reference to this UBI volume via the MTD device
* interface. Open the corresponding volume in read-write mode.
*/
vol->gluebi_desc = ubi_open_volume(vol->ubi->ubi_num, vol->vol_id,
UBI_READWRITE);
if (IS_ERR(vol->gluebi_desc))
return PTR_ERR(vol->gluebi_desc);
vol->gluebi_refcount += 1;
return 0;
}
/**
* gluebi_put_device - put MTD device reference.
* @mtd: the MTD device description object
*
* This function is called every time the MTD device is being put. Returns
* zero in case of success and a negative error code in case of failure.
*/
static void gluebi_put_device(struct mtd_info *mtd)
{
struct ubi_volume *vol;
vol = container_of(mtd, struct ubi_volume, gluebi_mtd);
vol->gluebi_refcount -= 1;
ubi_assert(vol->gluebi_refcount >= 0);
if (vol->gluebi_refcount == 0)
ubi_close_volume(vol->gluebi_desc);
}
/**
* gluebi_read - read operation of emulated MTD devices.
* @mtd: MTD device description object
* @from: absolute offset from where to read
* @len: how many bytes to read
* @retlen: count of read bytes is returned here
* @buf: buffer to store the read data
*
* This function returns zero in case of success and a negative error code in
* case of failure.
*/
static int gluebi_read(struct mtd_info *mtd, loff_t from, size_t len,
size_t *retlen, unsigned char *buf)
{
int err = 0, lnum, offs, total_read;
struct ubi_volume *vol;
struct ubi_device *ubi;
uint64_t tmp = from;
dbg_msg("read %zd bytes from offset %lld", len, from);
if (len < 0 || from < 0 || from + len > mtd->size)
return -EINVAL;
vol = container_of(mtd, struct ubi_volume, gluebi_mtd);
ubi = vol->ubi;
offs = do_div(tmp, mtd->erasesize);
lnum = tmp;
total_read = len;
while (total_read) {
size_t to_read = mtd->erasesize - offs;
if (to_read > total_read)
to_read = total_read;
err = ubi_eba_read_leb(ubi, vol->vol_id, lnum, buf, offs,
to_read, 0);
if (err)
break;
lnum += 1;
offs = 0;
total_read -= to_read;
buf += to_read;
}
*retlen = len - total_read;
return err;
}
/**
* gluebi_write - write operation of emulated MTD devices.
* @mtd: MTD device description object
* @to: absolute offset where to write
* @len: how many bytes to write
* @retlen: count of written bytes is returned here
* @buf: buffer with data to write
*
* This function returns zero in case of success and a negative error code in
* case of failure.
*/
static int gluebi_write(struct mtd_info *mtd, loff_t to, size_t len,
size_t *retlen, const u_char *buf)
{
int err = 0, lnum, offs, total_written;
struct ubi_volume *vol;
struct ubi_device *ubi;
uint64_t tmp = to;
dbg_msg("write %zd bytes to offset %lld", len, to);
if (len < 0 || to < 0 || len + to > mtd->size)
return -EINVAL;
vol = container_of(mtd, struct ubi_volume, gluebi_mtd);
ubi = vol->ubi;
if (ubi->ro_mode)
return -EROFS;
offs = do_div(tmp, mtd->erasesize);
lnum = tmp;
if (len % mtd->writesize || offs % mtd->writesize)
return -EINVAL;
total_written = len;
while (total_written) {
size_t to_write = mtd->erasesize - offs;
if (to_write > total_written)
to_write = total_written;
err = ubi_eba_write_leb(ubi, vol->vol_id, lnum, buf, offs,
to_write, UBI_UNKNOWN);
if (err)
break;
lnum += 1;
offs = 0;
total_written -= to_write;
buf += to_write;
}
*retlen = len - total_written;
return err;
}
/**
* gluebi_erase - erase operation of emulated MTD devices.
* @mtd: the MTD device description object
* @instr: the erase operation description
*
* This function calls the erase callback when finishes. Returns zero in case
* of success and a negative error code in case of failure.
*/
static int gluebi_erase(struct mtd_info *mtd, struct erase_info *instr)
{
int err, i, lnum, count;
struct ubi_volume *vol;
struct ubi_device *ubi;
dbg_msg("erase %u bytes at offset %u", instr->len, instr->addr);
if (instr->addr < 0 || instr->addr > mtd->size - mtd->erasesize)
return -EINVAL;
if (instr->len < 0 || instr->addr + instr->len > mtd->size)
return -EINVAL;
if (instr->addr % mtd->writesize || instr->len % mtd->writesize)
return -EINVAL;
lnum = instr->addr / mtd->erasesize;
count = instr->len / mtd->erasesize;
vol = container_of(mtd, struct ubi_volume, gluebi_mtd);
ubi = vol->ubi;
if (ubi->ro_mode)
return -EROFS;
for (i = 0; i < count; i++) {
err = ubi_eba_unmap_leb(ubi, vol->vol_id, lnum + i);
if (err)
goto out_err;
}
/*
* MTD erase operations are synchronous, so we have to make sure the
* physical eraseblock is wiped out.
*/
err = ubi_wl_flush(ubi);
if (err)
goto out_err;
instr->state = MTD_ERASE_DONE;
mtd_erase_callback(instr);
return 0;
out_err:
instr->state = MTD_ERASE_FAILED;
instr->fail_addr = lnum * mtd->erasesize;
return err;
}
/**
* ubi_create_gluebi - initialize gluebi for an UBI volume.
* @ubi: UBI device description object
* @vol: volume description object
*
* This function is called when an UBI volume is created in order to create
* corresponding fake MTD device. Returns zero in case of success and a
* negative error code in case of failure.
*/
int ubi_create_gluebi(struct ubi_device *ubi, struct ubi_volume *vol)
{
int err;
struct mtd_info *mtd = &vol->gluebi_mtd;
mtd->name = kmemdup(vol->name, vol->name_len + 1, GFP_KERNEL);
if (!mtd->name)
return -ENOMEM;
mtd->type = MTD_UBIVOLUME;
if (!ubi->ro_mode)
mtd->flags = MTD_WRITEABLE;
mtd->writesize = ubi->min_io_size;
mtd->owner = THIS_MODULE;
mtd->size = vol->usable_leb_size * vol->reserved_pebs;
mtd->erasesize = vol->usable_leb_size;
mtd->read = gluebi_read;
mtd->write = gluebi_write;
mtd->erase = gluebi_erase;
mtd->get_device = gluebi_get_device;
mtd->put_device = gluebi_put_device;
if (add_mtd_device(mtd)) {
ubi_err("cannot not add MTD device\n");
kfree(mtd->name);
return -ENFILE;
}
dbg_msg("added mtd%d (\"%s\"), size %u, EB size %u",
mtd->index, mtd->name, mtd->size, mtd->erasesize);
return 0;
}
/**
* ubi_destroy_gluebi - close gluebi for an UBI volume.
* @vol: volume description object
*
* This function is called when an UBI volume is removed in order to remove
* corresponding fake MTD device. Returns zero in case of success and a
* negative error code in case of failure.
*/
int ubi_destroy_gluebi(struct ubi_volume *vol)
{
int err;
struct mtd_info *mtd = &vol->gluebi_mtd;
dbg_msg("remove mtd%d", mtd->index);
err = del_mtd_device(mtd);
if (err)
return err;
kfree(mtd->name);
return 0;
}
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
此差异已折叠。
...@@ -3,3 +3,5 @@ header-y += jffs2-user.h ...@@ -3,3 +3,5 @@ header-y += jffs2-user.h
header-y += mtd-abi.h header-y += mtd-abi.h
header-y += mtd-user.h header-y += mtd-user.h
header-y += nftl-user.h header-y += nftl-user.h
header-y += ubi-header.h
header-y += ubi-user.h
...@@ -24,6 +24,7 @@ struct mtd_oob_buf { ...@@ -24,6 +24,7 @@ struct mtd_oob_buf {
#define MTD_NORFLASH 3 #define MTD_NORFLASH 3
#define MTD_NANDFLASH 4 #define MTD_NANDFLASH 4
#define MTD_DATAFLASH 6 #define MTD_DATAFLASH 6
#define MTD_UBIVOLUME 7
#define MTD_WRITEABLE 0x400 /* Device is writeable */ #define MTD_WRITEABLE 0x400 /* Device is writeable */
#define MTD_BIT_WRITEABLE 0x800 /* Single bits can be flipped */ #define MTD_BIT_WRITEABLE 0x800 /* Single bits can be flipped */
......
此差异已折叠。
此差异已折叠。
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册