Merge tag 'dt-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC DT updates from Arnd Bergmann:
 "As usual, the bulk of work in the SoC tree goes into DT files, this
  time with a roughly even split between 32-bit and 64-bit SoCs rather
  than the usual mostly 64-bit changes.

  New SoCs:

   - Microchip SAMA7 SoC family based on Cortex-A7, a new 32-bit
     platform based on the older SAMA5 series.

   - Qualcomm Snapdragon SDM636 and SM8150, variations of the existing
     phone SoCs.

   - Renesas R-Car H3e-2G and M3e-2G SoCs, variations of older Renesas
     SoCs.

  New boards:

   - Marvell CN913x reference boards

   - ASpeed AST2600 BMC implementations for Facebook Cloudripper, Elbert
     and Fuji server boards.

   - Snapdragon 665 based Sony Xperia 10II

   - Snapdragon MSM8916 based Xiaomi Redmi 2

   - Snapdragon MSM8226 based Samsung Galaxy S3 Neo

   - NXP i.MX based 32-bit boards:
       - DHCOM based PicoITX
       - DHSOM based DRC0ỉ
       - SolidRun SolidSense
       - SKOV i.MX6 boards.

   - NXP i.MX based 64-bit boards:
       - Nitrogen8 SoM and MNT Reform2
       - LS1088A based Traverse Ten64
       - i.MX8M based GW7902.

   - NVIDIA Jetson TX2 NX Developer Kit

   - 4KOpen STiH418-b2264 development board

   - ux500 based Samsung phones: Gavini, Codina and Kyle

   - TI AM335x based Sancloud BBE Lite

   - ixp4xx dts files to replace all old board files

  Other changes:

   - Treewide fixes for dtc warnings

   - Rockchips i/o domain support

   - TI OMAP/AM3 CPSW switch driver support

   - Improved device support for allwinner, aspeed, qualcomm, NXP,
     nvidia, Renesas, Samsung, Amlogic, Mediatek, ixp4xx, stm32, sti,
     OMAP and actions"

* tag 'dt-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (412 commits)
  arm/arm64: dts: Fix remaining dtc 'unit_address_format' warnings
  ARM: dts: rockchip: Add SFC to RV1108
  arm64: dts: marvell: armada-37xx: Extend PCIe MEM space
  ARM: dts: aspeed: p10bmc: Add power control pins
  ARM: dts: aspeed: cloudripper: Add comments for "mdio1"
  ARM: dts: aspeed: minipack: Update flash partition table
  dt-bindings: arm: fsl: Add Traverse Ten64 (LS1088A) board
  dt-bindings: vendor-prefixes: add Traverse Technologies
  arm64: dts: add device tree for Traverse Ten64 (LS1088A)
  arm64: dts: ls1088a: add missing PMU node
  arm64: dts: ls1088a: add internal PCS for DPMAC1 node
  ARM: dts: imx6qp-prtwd3: configure ENET_REF clock to 125MHz
  ARM: dts: vf610-zii-dev-rev-b: Remove #address-cells and #size-cells property from at93c46d dt node
  ARM: dts: add SKOV imx6q and imx6dl based boards
  dt-bindings: arm: fsl: add SKOV imx6q and imx6dl based boards
  dt-bindings: vendor-prefixes: Add an entry for SKOV A/S
  arm64: dts: imx8mq-reform2: add sound support
  arm64: dts: imx8m: drop interrupt-affinity for pmu
  arm64: dts: imx8qxp: update pmu compatible
  arm64: dts: imx8mm: update pmu compatible
  ...

Documentation/devicetree/bindings/arm/atmel-at91.yaml

@@ -145,6 +145,11 @@ properties:
           - const: atmel,sama5d4
           - const: atmel,sama5
 
+      - items:
+          - const: microchip,sama7g5ek # SAMA7G5 Evaluation Kit
+          - const: microchip,sama7g5
+          - const: microchip,sama7
+
       - items:
           - enum:
               - atmel,sams70j19

Documentation/devicetree/bindings/arm/atmel-sysregs.txt

@@ -45,7 +45,8 @@ RAMC SDRAM/DDR Controller required properties:
 			"atmel,at91sam9260-sdramc",
 			"atmel,at91sam9g45-ddramc",
 			"atmel,sama5d3-ddramc",
-			"microchip,sam9x60-ddramc"
+			"microchip,sam9x60-ddramc",
+			"microchip,sama7g5-uddrc"
 - reg: Should contain registers location and length
 
 Examples:
@@ -55,6 +56,17 @@ Examples:
 		reg = <0xffffe800 0x200>;
 	};
 
+RAMC PHY Controller required properties:
+- compatible: Should be "microchip,sama7g5-ddr3phy", "syscon"
+- reg: Should contain registers location and length
+
+Example:
+
+	ddr3phy: ddr3phy@e3804000 {
+		compatible = "microchip,sama7g5-ddr3phy", "syscon";
+		reg = <0xe3804000 0x1000>;
+};
+
 SHDWC Shutdown Controller
 
 required properties:

Documentation/devicetree/bindings/arm/fsl.yaml

@@ -221,9 +221,13 @@ properties:
               - prt,prti6q                # Protonic PRTI6Q board
               - prt,prtwd2                # Protonic WD2 board
               - rex,imx6q-rex-pro         # Rex Pro i.MX6 Quad Board
+              - skov,imx6q-skov-revc-lt2  # SKOV IMX6 CPU QuadCore lt2
+              - skov,imx6q-skov-revc-lt6  # SKOV IMX6 CPU QuadCore lt6
+              - skov,imx6q-skov-reve-mi1010ait-1cp1 # SKOV IMX6 CPU QuadCore mi1010ait-1cp1
               - solidrun,cubox-i/q        # SolidRun Cubox-i Dual/Quad
               - solidrun,hummingboard/q
               - solidrun,hummingboard2/q
+              - solidrun,solidsense/q     # SolidRun SolidSense Dual/Quad
               - tbs,imx6q-tbs2910         # TBS2910 Matrix ARM mini PC
               - technexion,imx6q-pico-dwarf   # TechNexion i.MX6Q Pico-Dwarf
               - technexion,imx6q-pico-hobbit  # TechNexion i.MX6Q Pico-Hobbit
@@ -377,9 +381,12 @@ properties:
               - prt,prtvt7                # Protonic VT7 board
               - rex,imx6dl-rex-basic      # Rex Basic i.MX6 Dual Lite Board
               - riot,imx6s-riotboard      # RIoTboard i.MX6S
+              - skov,imx6dl-skov-revc-lt2 # SKOV IMX6 CPU SoloCore lt2
+              - skov,imx6dl-skov-revc-lt6 # SKOV IMX6 CPU SoloCore lt6
               - solidrun,cubox-i/dl            # SolidRun Cubox-i Solo/DualLite
               - solidrun,hummingboard/dl
               - solidrun,hummingboard2/dl      # SolidRun HummingBoard2 Solo/DualLite
+              - solidrun,solidsense/dl         # SolidRun SolidSense Solo/DualLite
               - technexion,imx6dl-pico-dwarf   # TechNexion i.MX6DL Pico-Dwarf
               - technexion,imx6dl-pico-hobbit  # TechNexion i.MX6DL Pico-Hobbit
               - technexion,imx6dl-pico-nymph   # TechNexion i.MX6DL Pico-Nymph
@@ -418,6 +425,12 @@ properties:
           - const: dfi,fs700e-m60
           - const: fsl,imx6dl
 
+      - description: i.MX6DL DHCOM PicoITX Board
+        items:
+          - const: dh,imx6dl-dhcom-picoitx
+          - const: dh,imx6dl-dhcom-som
+          - const: fsl,imx6dl
+
       - description: i.MX6DL Gateworks Ventana Boards
         items:
           - enum:
@@ -469,6 +482,12 @@ properties:
           - const: toradex,colibri_imx6dl          # Colibri iMX6 Module
           - const: fsl,imx6dl
 
+      - description: i.MX6S DHCOM DRC02 Board
+        items:
+          - const: dh,imx6s-dhcom-drc02
+          - const: dh,imx6s-dhcom-som
+          - const: fsl,imx6dl
+
       - description: i.MX6SL based Boards
         items:
           - enum:
@@ -698,6 +717,7 @@ properties:
               - gw,imx8mm-gw72xx-0x       # i.MX8MM Gateworks Development Kit
               - gw,imx8mm-gw73xx-0x       # i.MX8MM Gateworks Development Kit
               - gw,imx8mm-gw7901          # i.MX8MM Gateworks Board
+              - gw,imx8mm-gw7902          # i.MX8MM Gateworks Board
               - kontron,imx8mm-n801x-som  # i.MX8MM Kontron SL (N801X) SOM
               - variscite,var-som-mx8mm   # i.MX8MM Variscite VAR-SOM-MX8MM module
           - const: fsl,imx8mm
@@ -728,6 +748,7 @@ properties:
               - beacon,imx8mn-beacon-kit  # i.MX8MN Beacon Development Kit
               - fsl,imx8mn-ddr4-evk       # i.MX8MN DDR4 EVK Board
               - fsl,imx8mn-evk            # i.MX8MN LPDDR4 EVK Board
+              - gw,imx8mn-gw7902          # i.MX8MM Gateworks Board
           - const: fsl,imx8mn
 
       - description: Variscite VAR-SOM-MX8MN based boards
@@ -752,10 +773,12 @@ properties:
         items:
           - enum:
               - boundary,imx8mq-nitrogen8m # i.MX8MQ NITROGEN Board
+              - boundary,imx8mq-nitrogen8m-som # i.MX8MQ NITROGEN SoM
               - einfochips,imx8mq-thor96  # i.MX8MQ Thor96 Board
               - fsl,imx8mq-evk            # i.MX8MQ EVK Board
               - google,imx8mq-phanbell    # Google Coral Edge TPU
               - kontron,pitx-imx8m        # Kontron pITX-imx8m Board
+              - mntre,reform2             # MNT Reform2 Laptop
               - purism,librem5-devkit     # Purism Librem5 devkit
               - solidrun,hummingboard-pulse # SolidRun Hummingboard Pulse
               - technexion,pico-pi-imx8m  # TechNexion PICO-PI-8M evk
@@ -973,6 +996,12 @@ properties:
               - fsl,s32v234-evb           # S32V234-EVB2 Customer Evaluation Board
           - const: fsl,s32v234
 
+      - description: Traverse LS1088A based Boards
+        items:
+          - enum:
+              - traverse,ten64            # Ten64 Networking Appliance / Board
+          - const: fsl,ls1088a
+
 additionalProperties: true
 
 ...

Documentation/devicetree/bindings/arm/qcom.yaml

@@ -31,6 +31,7 @@ description: |
         ipq6018
         ipq8074
         mdm9615
+        msm8226
         msm8916
         msm8974
         msm8992
@@ -114,6 +115,11 @@ properties:
               - qcom,apq8084-sbc
           - const: qcom,apq8084
 
+      - items:
+          - enum:
+              - samsung,s3ve3g
+          - const: qcom,msm8226
+
       - items:
           - enum:
               - qcom,msm8960-cdp
@@ -129,6 +135,8 @@ properties:
           - const: qcom,msm8974
 
       - items:
+          - enum:
+              - alcatel,idol347
           - const: qcom,msm8916-mtp/1
           - const: qcom,msm8916-mtp
           - const: qcom,msm8916
@@ -181,6 +189,8 @@ properties:
       - items:
           - enum:
               - qcom,sc7280-idp
+              - qcom,sc7280-idp2
+              - google,piglin
               - google,senor
           - const: qcom,sc7280
 

Documentation/devicetree/bindings/arm/renesas.yaml

@@ -238,17 +238,29 @@ properties:
           - const: renesas,r8a77961
 
       - description: Kingfisher (SBEV-RCAR-KF-M03)
-        items:
-          - const: shimafuji,kingfisher
-          - enum:
-              - renesas,h3ulcb
-              - renesas,m3ulcb
-              - renesas,m3nulcb
-          - enum:
-              - renesas,r8a7795
-              - renesas,r8a7796
-              - renesas,r8a77961
-              - renesas,r8a77965
+        oneOf:
+          - items:
+              - const: shimafuji,kingfisher
+              - enum:
+                  - renesas,h3ulcb
+                  - renesas,m3ulcb
+                  - renesas,m3nulcb
+              - enum:
+                  - renesas,r8a7795
+                  - renesas,r8a7796
+                  - renesas,r8a77961
+                  - renesas,r8a77965
+          - items:
+              - const: shimafuji,kingfisher
+              - enum:
+                  - renesas,h3ulcb
+                  - renesas,m3ulcb
+              - enum:
+                  - renesas,r8a779m1
+                  - renesas,r8a779m3
+              - enum:
+                  - renesas,r8a7795
+                  - renesas,r8a77961
 
       - description: R-Car M3-N (R8A77965)
         items:
@@ -296,6 +308,22 @@ properties:
           - const: renesas,falcon-cpu
           - const: renesas,r8a779a0
 
+      - description: R-Car H3e-2G (R8A779M1)
+        items:
+          - enum:
+              - renesas,h3ulcb      # H3ULCB (R-Car Starter Kit Premier)
+              - renesas,salvator-xs # Salvator-XS (Salvator-X 2nd version)
+          - const: renesas,r8a779m1
+          - const: renesas,r8a7795
+
+      - description: R-Car M3e-2G (R8A779M3)
+        items:
+          - enum:
+              - renesas,m3ulcb      # M3ULCB (R-Car Starter Kit Pro)
+              - renesas,salvator-xs # Salvator-XS (Salvator-X 2nd version)
+          - const: renesas,r8a779m3
+          - const: renesas,r8a77961
+
       - description: RZ/N1D (R9A06G032)
         items:
           - enum:

Documentation/devicetree/bindings/arm/tegra.yaml

@@ -111,6 +111,7 @@ properties:
       - items:
           - enum:
               - nvidia,p2771-0000
+              - nvidia,p3509-0000+p3636-0001
           - const: nvidia,tegra186
       - items:
           - enum:

Documentation/devicetree/bindings/gpio/aspeed,sgpio.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/gpio/aspeed,sgpio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Aspeed SGPIO controller
+
+maintainers:
+  - Andrew Jeffery <andrew@aj.id.au>
+
+description:
+  This SGPIO controller is for ASPEED AST2400, AST2500 and AST2600 SoC,
+  AST2600 have two sgpio master one with 128 pins another one with 80 pins,
+  AST2500/AST2400 have one sgpio master with 80 pins. Each of the Serial
+  GPIO pins can be programmed to support the following options
+  - Support interrupt option for each input port and various interrupt
+    sensitivity option (level-high, level-low, edge-high, edge-low)
+  - Support reset tolerance option for each output port
+  - Directly connected to APB bus and its shift clock is from APB bus clock
+    divided by a programmable value.
+  - Co-work with external signal-chained TTL components (74LV165/74LV595)
+
+properties:
+  compatible:
+    enum:
+      - aspeed,ast2400-sgpio
+      - aspeed,ast2500-sgpio
+      - aspeed,ast2600-sgpiom
+
+  reg:
+    maxItems: 1
+
+  gpio-controller: true
+
+  '#gpio-cells':
+    const: 2
+
+  interrupts:
+    maxItems: 1
+
+  interrupt-controller: true
+
+  clocks:
+    maxItems: 1
+
+  ngpios: true
+
+  bus-frequency: true
+
+required:
+  - compatible
+  - reg
+  - gpio-controller
+  - '#gpio-cells'
+  - interrupts
+  - interrupt-controller
+  - ngpios
+  - clocks
+  - bus-frequency
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/aspeed-clock.h>
+    sgpio: sgpio@1e780200 {
+        #gpio-cells = <2>;
+        compatible = "aspeed,ast2500-sgpio";
+        gpio-controller;
+        interrupts = <40>;
+        reg = <0x1e780200 0x0100>;
+        clocks = <&syscon ASPEED_CLK_APB>;
+        interrupt-controller;
+        ngpios = <80>;
+        bus-frequency = <12000000>;
+    };

Documentation/devicetree/bindings/gpio/sgpio-aspeed.txt

-Aspeed SGPIO controller Device Tree Bindings
---------------------------------------------
-
-This SGPIO controller is for ASPEED AST2500 SoC, it supports up to 80 full
-featured Serial GPIOs. Each of the Serial GPIO pins can be programmed to
-support the following options:
-- Support interrupt option for each input port and various interrupt
-  sensitivity option (level-high, level-low, edge-high, edge-low)
-- Support reset tolerance option for each output port
-- Directly connected to APB bus and its shift clock is from APB bus clock
-  divided by a programmable value.
-- Co-work with external signal-chained TTL components (74LV165/74LV595)
-
-Required properties:
-
-- compatible : Should be one of
-  "aspeed,ast2400-sgpio", "aspeed,ast2500-sgpio"
-- #gpio-cells : Should be 2, see gpio.txt
-- reg : Address and length of the register set for the device
-- gpio-controller : Marks the device node as a GPIO controller
-- interrupts : Interrupt specifier, see interrupt-controller/interrupts.txt
-- interrupt-controller : Mark the GPIO controller as an interrupt-controller
-- ngpios : number of *hardware* GPIO lines, see gpio.txt. This will expose
-  2 software GPIOs per hardware GPIO: one for hardware input, one for hardware
-  output. Up to 80 pins, must be a multiple of 8.
-- clocks : A phandle to the APB clock for SGPM clock division
-- bus-frequency : SGPM CLK frequency
-
-The sgpio and interrupt properties are further described in their respective
-bindings documentation:
-
-- Documentation/devicetree/bindings/gpio/gpio.txt
-- Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
-
-  Example:
-	sgpio: sgpio@1e780200 {
-		#gpio-cells = <2>;
-		compatible = "aspeed,ast2500-sgpio";
-		gpio-controller;
-		interrupts = <40>;
-		reg = <0x1e780200 0x0100>;
-		clocks = <&syscon ASPEED_CLK_APB>;
-		interrupt-controller;
-		ngpios = <8>;
-		bus-frequency = <12000000>;
-	};

Documentation/devicetree/bindings/i2c/renesas,riic.yaml

@@ -27,14 +27,25 @@ properties:
 
   interrupts:
     items:
-      - description: Transmit End Interrupt (TEI)
-      - description: Receive Data Full Interrupt (RI)
-      - description: Transmit Data Empty Interrupt (TI)
-      - description: Stop Condition Detection Interrupt (SPI)
-      - description: Start Condition Detection Interrupt (STI)
-      - description: NACK Reception Interrupt (NAKI)
-      - description: Arbitration-Lost Interrupt (ALI)
-      - description: Timeout Interrupt (TMOI)
+      - description: Transmit End Interrupt
+      - description: Receive Data Full Interrupt
+      - description: Transmit Data Empty Interrupt
+      - description: Stop Condition Detection Interrupt
+      - description: Start Condition Detection Interrupt
+      - description: NACK Reception Interrupt
+      - description: Arbitration-Lost Interrupt
+      - description: Timeout Interrupt
+
+  interrupt-names:
+    items:
+      - const: tei
+      - const: ri
+      - const: ti
+      - const: spi
+      - const: sti
+      - const: naki
+      - const: ali
+      - const: tmoi
 
   clock-frequency:
     description:
@@ -51,6 +62,7 @@ required:
   - compatible
   - reg
   - interrupts
+  - interrupt-names
   - clocks
   - clock-frequency
   - power-domains
@@ -85,6 +97,8 @@ examples:
                          <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>,
                          <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>,
                          <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>;
+            interrupt-names = "tei", "ri", "ti", "spi", "sti", "naki", "ali",
+                              "tmoi";
             clocks = <&mstp9_clks R7S72100_CLK_I2C0>;
             clock-frequency = <100000>;
             power-domains = <&cpg_clocks>;

Documentation/devicetree/bindings/mailbox/mtk-gce.txt

@@ -35,6 +35,10 @@ Optional properties for a client device:
   start_offset: the start offset of register address that GCE can access.
   size: the total size of register address that GCE can access.
 
+Optional properties for a client mutex node:
+- mediatek,gce-events: GCE events used by clients. The event numbers are
+  defined in 'dt-bindings/gce/<chip>-gce.h'.
+
 Some vaules of properties are defined in 'dt-bindings/gce/mt8173-gce.h',
 'dt-binding/gce/mt8183-gce.h' or 'dt-bindings/gce/mt6779-gce.h'. Such as
 sub-system ids, thread priority, event ids.
@@ -62,3 +66,14 @@ Example for a client device:
 					  <&gce SUBSYS_1401XXXX 0x2000 0x100>;
 		...
 	};
+
+Example for a client mutex node:
+	mutex: mutex@14020000 {
+		compatible = "mediatek,mt8173-disp-mutex";
+		reg = <0 0x14020000 0 0x1000>;
+		interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_LOW>;
+		power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
+		clocks = <&mmsys CLK_MM_MUTEX_32K>;
+		mediatek,gce-events = <CMDQ_EVENT_MUTEX0_STREAM_EOF>,
+				      <CMDQ_EVENT_MUTEX1_STREAM_EOF>;
+	};

Documentation/devicetree/bindings/media/nxp,imx8-jpeg.yaml

@@ -16,12 +16,17 @@ description: |-
 
 properties:
   compatible:
-    items:
-      - enum:
-            # JPEG decoder
-          - nxp,imx8qxp-jpgdec
-            # JPEG encoder
-          - nxp,imx8qxp-jpgenc
+    oneOf:
+      - items:
+          enum:
+            - nxp,imx8qxp-jpgdec
+            - nxp,imx8qxp-jpgenc
+      - items:
+          - const: nxp,imx8qm-jpgdec
+          - const: nxp,imx8qxp-jpgdec
+      - items:
+          - const: nxp,imx8qm-jpgenc
+          - const: nxp,imx8qxp-jpgenc
 
   reg:
     maxItems: 1
@@ -69,7 +74,7 @@ examples:
     };
 
     jpegenc: jpegenc@58450000 {
-        compatible = "nxp,imx8qxp-jpgenc";
+        compatible = "nxp,imx8qm-jpgenc", "nxp,imx8qxp-jpgenc";
         reg = <0x58450000 0x00050000 >;
         interrupts = <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>,
                      <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>,

Documentation/devicetree/bindings/thermal/qcom-tsens.yaml

@@ -48,6 +48,7 @@ properties:
               - qcom,sc7180-tsens
               - qcom,sc7280-tsens
               - qcom,sc8180x-tsens
+              - qcom,sdm630-tsens
               - qcom,sdm845-tsens
               - qcom,sm8150-tsens
               - qcom,sm8250-tsens

Documentation/devicetree/bindings/vendor-prefixes.yaml

@@ -739,6 +739,8 @@ patternProperties:
     description: MiraMEMS Sensing Technology Co., Ltd.
   "^mitsubishi,.*":
     description: Mitsubishi Electric Corporation
+  "^mntre,.*":
+    description: MNT Research GmbH
   "^modtronix,.*":
     description: Modtronix Engineering
   "^mosaixtech,.*":
@@ -1072,6 +1074,8 @@ patternProperties:
     description: Silicon Integrated Systems Corp.
   "^sitronix,.*":
     description: Sitronix Technology Corporation
+  "^skov,.*":
+    description: SKOV A/S
   "^skyworks,.*":
     description: Skyworks Solutions, Inc.
   "^smartlabs,.*":
@@ -1190,6 +1194,8 @@ patternProperties:
     description: TPO
   "^tq,.*":
     description: TQ-Systems GmbH
+  "^traverse,.*":
+    description: Traverse Technologies Australia Pty Ltd
   "^tronfy,.*":
     description: Tronfy
   "^tronsmart,.*":

arch/arm/boot/dts/Makefile

@@ -74,6 +74,8 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
 	at91-sama5d4_xplained.dtb \
 	at91-sama5d4ek.dtb \
 	at91-vinco.dtb
+dtb-$(CONFIG_SOC_SAMA7G5) += \
+	at91-sama7g5ek.dtb
 dtb-$(CONFIG_ARCH_AXXIA) += \
 	axm5516-amarillo.dtb
 dtb-$(CONFIG_ARCH_BCM2835) += \
@@ -241,8 +243,20 @@ dtb-$(CONFIG_ARCH_INTEGRATOR) += \
 	integratorcp.dtb
 dtb-$(CONFIG_ARCH_IXP4XX) += \
 	intel-ixp42x-linksys-nslu2.dtb \
+	intel-ixp42x-linksys-wrv54g.dtb \
+	intel-ixp42x-freecom-fsg-3.dtb \
 	intel-ixp42x-welltech-epbx100.dtb \
-	intel-ixp43x-gateworks-gw2358.dtb
+	intel-ixp42x-ixdp425.dtb \
+	intel-ixp43x-kixrp435.dtb \
+	intel-ixp46x-ixdp465.dtb \
+	intel-ixp42x-adi-coyote.dtb \
+	intel-ixp42x-ixdpg425.dtb \
+	intel-ixp42x-iomega-nas100d.dtb \
+	intel-ixp42x-dlink-dsm-g600.dtb \
+	intel-ixp42x-gateworks-gw2348.dtb \
+	intel-ixp43x-gateworks-gw2358.dtb \
+	intel-ixp42x-netgear-wg302v2.dtb \
+	intel-ixp42x-arcom-vulcan.dtb
 dtb-$(CONFIG_ARCH_KEYSTONE) += \
 	keystone-k2hk-evm.dtb \
 	keystone-k2l-evm.dtb \
@@ -429,6 +443,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6dl-cubox-i-emmc-som-v15.dtb \
 	imx6dl-cubox-i-som-v15.dtb \
 	imx6dl-dfi-fs700-m60.dtb \
+	imx6dl-dhcom-picoitx.dtb \
 	imx6dl-eckelmann-ci4x10.dtb \
 	imx6dl-emcon-avari.dtb \
 	imx6dl-gw51xx.dtb \
@@ -475,6 +490,9 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6dl-sabrelite.dtb \
 	imx6dl-sabresd.dtb \
 	imx6dl-savageboard.dtb \
+	imx6dl-skov-revc-lt2.dtb \
+	imx6dl-skov-revc-lt6.dtb \
+	imx6dl-solidsense.dtb \
 	imx6dl-ts4900.dtb \
 	imx6dl-ts7970.dtb \
 	imx6dl-tx6dl-comtft.dtb \
@@ -575,6 +593,10 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6q-sabresd.dtb \
 	imx6q-savageboard.dtb \
 	imx6q-sbc6x.dtb \
+	imx6q-skov-revc-lt2.dtb \
+	imx6q-skov-revc-lt6.dtb \
+	imx6q-skov-reve-mi1010ait-1cp1.dtb \
+	imx6q-solidsense.dtb \
 	imx6q-tbs2910.dtb \
 	imx6q-ts4900.dtb \
 	imx6q-ts7970.dtb \
@@ -607,7 +629,8 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6qp-tx6qp-8137-mb7.dtb \
 	imx6qp-vicutp.dtb \
 	imx6qp-wandboard-revd1.dtb \
-	imx6qp-zii-rdu2.dtb
+	imx6qp-zii-rdu2.dtb \
+	imx6s-dhcom-drc02.dtb
 dtb-$(CONFIG_SOC_IMX6SL) += \
 	imx6sl-evk.dtb \
 	imx6sl-tolino-shine2hd.dtb \
@@ -843,6 +866,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \
 	am335x-pocketbeagle.dtb \
 	am335x-regor-rdk.dtb \
 	am335x-sancloud-bbe.dtb \
+	am335x-sancloud-bbe-lite.dtb \
 	am335x-shc.dtb \
 	am335x-sbc-t335.dtb \
 	am335x-sl50.dtb \
@@ -933,6 +957,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
 	qcom-ipq4019-ap.dk07.1-c2.dtb \
 	qcom-ipq8064-ap148.dtb \
 	qcom-ipq8064-rb3011.dtb \
+	qcom-msm8226-samsung-s3ve3g.dtb \
 	qcom-msm8660-surf.dtb \
 	qcom-msm8960-cdp.dtb \
 	qcom-msm8974-fairphone-fp2.dtb \
@@ -1076,7 +1101,8 @@ dtb-$(CONFIG_ARCH_STI) += \
 	stih407-b2120.dtb \
 	stih410-b2120.dtb \
 	stih410-b2260.dtb \
-	stih418-b2199.dtb
+	stih418-b2199.dtb \
+	stih418-b2264.dtb
 dtb-$(CONFIG_ARCH_STM32) += \
 	stm32f429-disco.dtb \
 	stm32f469-disco.dtb \
@@ -1300,7 +1326,10 @@ dtb-$(CONFIG_ARCH_U8500) += \
 	ste-href520-tvk.dtb \
 	ste-ux500-samsung-golden.dtb \
 	ste-ux500-samsung-janice.dtb \
-	ste-ux500-samsung-skomer.dtb
+	ste-ux500-samsung-gavini.dtb \
+	ste-ux500-samsung-codina.dtb \
+	ste-ux500-samsung-skomer.dtb \
+	ste-ux500-samsung-kyle.dtb
 dtb-$(CONFIG_ARCH_UNIPHIER) += \
 	uniphier-ld4-ref.dtb \
 	uniphier-ld6b-ref.dtb \
@@ -1433,7 +1462,10 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
 	aspeed-bmc-arm-stardragon4800-rep2.dtb \
 	aspeed-bmc-asrock-e3c246d4i.dtb \
 	aspeed-bmc-bytedance-g220a.dtb \
+	aspeed-bmc-facebook-cloudripper.dtb \
 	aspeed-bmc-facebook-cmm.dtb \
+	aspeed-bmc-facebook-elbert.dtb \
+	aspeed-bmc-facebook-fuji.dtb \
 	aspeed-bmc-facebook-galaxy100.dtb \
 	aspeed-bmc-facebook-minipack.dtb \
 	aspeed-bmc-facebook-tiogapass.dtb \
@@ -1448,6 +1480,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
 	aspeed-bmc-ibm-rainier-4u.dtb \
 	aspeed-bmc-intel-s2600wf.dtb \
 	aspeed-bmc-inspur-fp5280g2.dtb \
+	aspeed-bmc-inspur-nf5280m6.dtb \
 	aspeed-bmc-lenovo-hr630.dtb \
 	aspeed-bmc-lenovo-hr855xg2.dtb \
 	aspeed-bmc-microsoft-olympus.dtb \

arch/arm/boot/dts/am335x-baltos-ir2110.dts

@@ -58,21 +58,21 @@
 	dr_mode = "host";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	phy0: ethernet-phy@0 {
 		reg = <1>;
 	};
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-mode = "rmii";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <1>;
 	phy-handle = <&phy0>;
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-mode = "rgmii-id";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 	phy-handle = <&phy1>;
 };
 

arch/arm/boot/dts/am335x-baltos-ir3220.dts

@@ -103,18 +103,18 @@
 	dr_mode = "host";
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-mode = "rmii";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <1>;
 	fixed-link {
 		speed = <100>;
 		full-duplex;
 	};
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-mode = "rgmii-id";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 	phy-handle = <&phy1>;
 };
 

arch/arm/boot/dts/am335x-baltos-ir5221.dts

@@ -120,18 +120,18 @@
 	dr_mode = "host";
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-mode = "rmii";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <1>;
 	fixed-link {
 		speed = <100>;
 		full-duplex;
 	};
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-mode = "rgmii-id";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 	phy-handle = <&phy1>;
 };
 

arch/arm/boot/dts/am335x-baltos.dtsi

@@ -339,16 +339,15 @@
 	};
 };
 
-&mac {
+&mac_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
-	dual_emac = <1>;
 
 	status = "okay";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	status = "okay";
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&davinci_mdio_default>;

arch/arm/boot/dts/am335x-bone-common.dtsi

@@ -353,24 +353,27 @@
 	};
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "mii";
+	ti,dual-emac-pvid = <1>;
 };
 
-&mac {
-	slaves = <1>;
+&cpsw_port2 {
+	status = "disabled";
+};
+
+&mac_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
 	status = "okay";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&davinci_mdio_default>;
 	pinctrl-1 = <&davinci_mdio_sleep>;
-	status = "okay";
 
 	ethphy0: ethernet-phy@0 {
 		reg = <0>;
@@ -397,3 +400,7 @@
 	clocks = <&clk_32768_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>;
 	clock-names = "ext-clk", "int-clk";
 };
+
+&pruss_tm {
+	status = "okay";
+};

arch/arm/boot/dts/am335x-boneblack-common.dtsi

@@ -3,9 +3,6 @@
  * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  */
 
-#include <dt-bindings/display/tda998x.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-
 &ldo3_reg {
 	regulator-min-microvolt = <1800000>;
 	regulator-max-microvolt = <1800000>;
@@ -25,145 +22,13 @@
 	non-removable;
 };
 
-&am33xx_pinmux {
-	nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR0, PIN_OUTPUT_PULLDOWN, MUX_MODE3)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA0, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA1, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA2, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA3, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA4, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA5, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA6, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA7, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA8, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA9, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA10, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA11, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA12, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA13, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA14, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_DATA15, PIN_OUTPUT, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_VSYNC, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_HSYNC, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_PCLK, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_LCD_AC_BIAS_EN, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
-		>;
-	};
-
-	nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR0, PIN_OUTPUT_PULLDOWN, MUX_MODE3)
-		>;
-	};
-
-	mcasp0_pins: mcasp0_pins {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKX, PIN_INPUT_PULLUP, MUX_MODE0) /* mcasp0_ahcklx.mcasp0_ahclkx */
-			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKR, PIN_OUTPUT_PULLDOWN, MUX_MODE2) /* mcasp0_ahclkr.mcasp0_axr2*/
-			AM33XX_PADCONF(AM335X_PIN_MCASP0_FSX, PIN_OUTPUT_PULLUP, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_MCASP0_ACLKX, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_GPMC_A11, PIN_OUTPUT_PULLDOWN, MUX_MODE7) /* gpmc_a11.GPIO1_27 */
-		>;
-	};
-};
-
-&lcdc {
-	status = "okay";
-
-	/* If you want to get 24 bit RGB and 16 BGR mode instead of
-	 * current 16 bit RGB and 24 BGR modes, set the propety
-	 * below to "crossed" and uncomment the video-ports -property
-	 * in tda19988 node.
-	 */
-	blue-and-red-wiring = "straight";
-
-	port {
-		lcdc_0: endpoint@0 {
-			remote-endpoint = <&hdmi_0>;
-		};
-	};
-};
-
-&i2c0 {
-	tda19988: tda19988@70 {
-		compatible = "nxp,tda998x";
-		reg = <0x70>;
-		nxp,calib-gpios = <&gpio1 25 0>;
-		interrupts-extended = <&gpio1 25 IRQ_TYPE_LEVEL_LOW>;
-
-		pinctrl-names = "default", "off";
-		pinctrl-0 = <&nxp_hdmi_bonelt_pins>;
-		pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>;
-
-		/* Convert 24bit BGR to RGB, e.g. cross red and blue wiring */
-		/* video-ports = <0x234501>; */
-
-		#sound-dai-cells = <0>;
-		audio-ports = <	TDA998x_I2S	0x03>;
-
-		ports {
-			port@0 {
-				hdmi_0: endpoint@0 {
-					remote-endpoint = <&lcdc_0>;
-				};
-			};
-		};
-	};
-};
-
 &rtc {
 	system-power-controller;
 };
 
-&mcasp0	{
-	#sound-dai-cells = <0>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcasp0_pins>;
-	status = "okay";
-	op-mode = <0>;	/* MCASP_IIS_MODE */
-	tdm-slots = <2>;
-	serial-dir = <	/* 0: INACTIVE, 1: TX, 2: RX */
-			0 0 1 0
-		>;
-	tx-num-evt = <32>;
-	rx-num-evt = <32>;
-};
-
 / {
 	memory@80000000 {
 		device_type = "memory";
 		reg = <0x80000000 0x20000000>; /* 512 MB */
 	};
-
-	clk_mcasp0_fixed: clk_mcasp0_fixed {
-		#clock-cells = <0>;
-		compatible = "fixed-clock";
-		clock-frequency = <24576000>;
-	};
-
-	clk_mcasp0: clk_mcasp0 {
-		#clock-cells = <0>;
-		compatible = "gpio-gate-clock";
-		clocks = <&clk_mcasp0_fixed>;
-		enable-gpios = <&gpio1 27 0>; /* BeagleBone Black Clk enable on GPIO1_27 */
-	};
-
-	sound {
-		compatible = "simple-audio-card";
-		simple-audio-card,name = "TI BeagleBone Black";
-		simple-audio-card,format = "i2s";
-		simple-audio-card,bitclock-master = <&dailink0_master>;
-		simple-audio-card,frame-master = <&dailink0_master>;
-
-		dailink0_master: simple-audio-card,cpu {
-			sound-dai = <&mcasp0>;
-			clocks = <&clk_mcasp0>;
-		};
-
-		simple-audio-card,codec {
-			sound-dai = <&tda19988>;
-		};
-	};
 };

arch/arm/boot/dts/am335x-boneblack-hdmi.dtsi

+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+#include <dt-bindings/display/tda998x.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+&am33xx_pinmux {
+	nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR0, PIN_OUTPUT_PULLDOWN, MUX_MODE3)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA0, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA1, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA2, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA3, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA4, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA5, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA6, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA7, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA8, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA9, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA10, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA11, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA12, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA13, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA14, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA15, PIN_OUTPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_VSYNC, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_HSYNC, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_PCLK, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_LCD_AC_BIAS_EN, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
+		>;
+	};
+
+	nxp_hdmi_bonelt_off_pins: nxp_hdmi_bonelt_off_pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR0, PIN_OUTPUT_PULLDOWN, MUX_MODE3)
+		>;
+	};
+
+	mcasp0_pins: mcasp0_pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKX, PIN_INPUT_PULLUP, MUX_MODE0) /* mcasp0_ahcklx.mcasp0_ahclkx */
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKR, PIN_OUTPUT_PULLDOWN, MUX_MODE2) /* mcasp0_ahclkr.mcasp0_axr2*/
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_FSX, PIN_OUTPUT_PULLUP, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_ACLKX, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A11, PIN_OUTPUT_PULLDOWN, MUX_MODE7) /* gpmc_a11.GPIO1_27 */
+		>;
+	};
+};
+
+&lcdc {
+	status = "okay";
+
+	/* If you want to get 24 bit RGB and 16 BGR mode instead of
+	 * current 16 bit RGB and 24 BGR modes, set the propety
+	 * below to "crossed" and uncomment the video-ports -property
+	 * in tda19988 node.
+	 */
+	blue-and-red-wiring = "straight";
+
+	port {
+		lcdc_0: endpoint@0 {
+			remote-endpoint = <&hdmi_0>;
+		};
+	};
+};
+
+&i2c0 {
+	tda19988: tda19988@70 {
+		compatible = "nxp,tda998x";
+		reg = <0x70>;
+		nxp,calib-gpios = <&gpio1 25 0>;
+		interrupts-extended = <&gpio1 25 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-names = "default", "off";
+		pinctrl-0 = <&nxp_hdmi_bonelt_pins>;
+		pinctrl-1 = <&nxp_hdmi_bonelt_off_pins>;
+
+		/* Convert 24bit BGR to RGB, e.g. cross red and blue wiring */
+		/* video-ports = <0x234501>; */
+
+		#sound-dai-cells = <0>;
+		audio-ports = <	TDA998x_I2S	0x03>;
+
+		ports {
+			port@0 {
+				hdmi_0: endpoint@0 {
+					remote-endpoint = <&lcdc_0>;
+				};
+			};
+		};
+	};
+};
+
+&mcasp0	{
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcasp0_pins>;
+	status = "okay";
+	op-mode = <0>;	/* MCASP_IIS_MODE */
+	tdm-slots = <2>;
+	serial-dir = <	/* 0: INACTIVE, 1: TX, 2: RX */
+			0 0 1 0
+		>;
+	tx-num-evt = <32>;
+	rx-num-evt = <32>;
+};
+
+/ {
+	clk_mcasp0_fixed: clk_mcasp0_fixed {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <24576000>;
+	};
+
+	clk_mcasp0: clk_mcasp0 {
+		#clock-cells = <0>;
+		compatible = "gpio-gate-clock";
+		clocks = <&clk_mcasp0_fixed>;
+		enable-gpios = <&gpio1 27 0>; /* BeagleBone Black Clk enable on GPIO1_27 */
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "TI BeagleBone Black";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,bitclock-master = <&dailink0_master>;
+		simple-audio-card,frame-master = <&dailink0_master>;
+
+		dailink0_master: simple-audio-card,cpu {
+			sound-dai = <&mcasp0>;
+			clocks = <&clk_mcasp0>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&tda19988>;
+		};
+	};
+};

arch/arm/boot/dts/am335x-boneblack-wireless.dts

@@ -7,6 +7,7 @@
 #include "am33xx.dtsi"
 #include "am335x-bone-common.dtsi"
 #include "am335x-boneblack-common.dtsi"
+#include "am335x-boneblack-hdmi.dtsi"
 #include <dt-bindings/interrupt-controller/irq.h>
 
 / {
@@ -62,7 +63,7 @@
 	};
 };
 
-&mac {
+&mac_sw {
 	status = "disabled";
 };
 

arch/arm/boot/dts/am335x-boneblack.dts

@@ -7,6 +7,7 @@
 #include "am33xx.dtsi"
 #include "am335x-bone-common.dtsi"
 #include "am335x-boneblack-common.dtsi"
+#include "am335x-boneblack-hdmi.dtsi"
 
 / {
 	model = "TI AM335x BeagleBone Black";

arch/arm/boot/dts/am335x-boneblue.dts

@@ -435,12 +435,153 @@
 	status = "okay";
 };
 
+&gpio0 {
+	gpio-line-names =
+		"UART3_CTS", /* M17 */
+		"UART3_RTS", /* M18 */
+		"UART2_RX", /* A17 */
+		"UART2_TX", /* B17 */
+		"I2C1_SDA", /* B16 */
+		"I2C1_SCL", /* A16 */
+		"MMC0_CD", /* C15 */
+		"SPI1_SS2", /* C18 */
+		"EQEP_1A", /* V2 */
+		"EQEP_1B", /* V3 */
+		"MDIR_2B", /* V4 */
+		"BATT_LED_2", /* T5 */
+		"I2C2_SDA", /* D18 */
+		"I2C2_SCL", /* D17 */
+		"UART1_RX", /* D16 */
+		"UART1_TX", /* D15 */
+		"MMC2_DAT1", /* J18 */
+		"MMC2_DAT2", /* K15 */
+		"NC", /* F16 */
+		"WIFI_LED", /* A15 */
+		"MOT_STBY", /* D14 */
+		"WLAN_IRQ", /* K16 */
+		"PWM_2A", /* U10 */
+		"PWM_2B", /* T10 */
+		"",
+		"",
+		"BATT_LED_4", /* T11 */
+		"BATT_LED_1", /* U12 */
+		"BT_EN", /* K17 */
+		"SPI1_SS1", /* H18 */
+		"UART4_RX", /* T17 */
+		"MDIR_1B"; /* U17 */
+};
+
+&gpio1 {
+	gpio-line-names =
+		"MMC1_DAT0", /* U7 */
+		"MMC1_DAT1", /* V7 */
+		"MMC1_DAT2", /* R8 */
+		"MMC1_DAT3", /* T8 */
+		"MMC1_DAT4", /* U8 */
+		"MMC1_DAT5", /* V8 */
+		"MMC1_DAT6", /* R9 */
+		"MMC1_DAT7", /* T9 */
+		"DCAN1_TX", /* E18 */
+		"DCAN1_RX", /* E17 */
+		"UART0_RX", /* E15 */
+		"UART0_TX", /* E16 */
+		"EQEP_2A", /* T12 */
+		"EQEP_2B", /* R12 */
+		"PRU_E_A", /* V13 */
+		"PRU_E_B", /* U13 */
+		"MDIR_2A", /* R13 */
+		"GPIO1_17", /* V14 */
+		"PWM_1A", /* U14 */
+		"PWM_1B", /* T14 */
+		"EMMC_RST", /* R14 */
+		"USR_LED_0", /* V15 */
+		"USR_LED_1", /* U15 */
+		"USR_LED_2", /* T15 */
+		"USR_LED_3", /* V16 */
+		"GPIO1_25", /* U16 */
+		"MCASP0_AXR0", /* T16 */
+		"MCASP0_AXR1", /* V17 */
+		"MCASP0_ACLKR", /* U18 */
+		"BATT_LED_3", /* V6 */
+		"MMC1_CLK", /* U9 */
+		"MMC1_CMD"; /* V9 */
+};
+
+&gpio2 {
+	gpio-line-names =
+		"MDIR_1A", /* T13 */
+		"MCASP0_FSR", /* V12 */
+		"LED_RED", /* R7 */
+		"LED_GREEN", /* T7 */
+		"MODE_BTN", /* U6 */
+		"PAUSE_BTN", /* T6 */
+		"MDIR_4A", /* R1 */
+		"MDIR_4B", /* R2 */
+		"MDIR_3B", /* R3 */
+		"MDIR_3A", /* R4 */
+		"SVO7", /* T1 */
+		"SVO8", /* T2 */
+		"SVO5", /* T3 */
+		"SVO6", /* T4 */
+		"UART5_TX", /* U1 */
+		"UART5_RX", /* U2 */
+		"SERVO_EN", /* U3 */
+		"NC", /* U4 */
+		"UART3_RX", /* L17 */
+		"UART3_TX", /* L16 */
+		"MMC2_CLK", /* L15 */
+		"DCAN1_SILENT", /* M16 */
+		"SVO1", /* U5 */
+		"SVO3", /* R5 */
+		"SVO2", /* V5 */
+		"SVO4", /* R6 */
+		"MMC0_DAT3", /* F17 */
+		"MMC0_DAT2", /* F18 */
+		"MMC0_DAT1", /* G15 */
+		"MMC0_DAT0", /* G16 */
+		"MMC0_CLK", /* G17 */
+		"MMC0_CMD"; /* G18 */
+};
+
 &gpio3 {
+	gpio-line-names =
+		"MMC2_DAT3", /* H16 */
+		"GPIO3_1", /* H17 */
+		"GPIO3_2", /* J15 */
+		"MMC2_CMD", /* J16 */
+		"MMC2_DAT0", /* J17 */
+		"I2C0_SDA", /* C17 */
+		"I2C0_SCL", /* C16 */
+		"EMU1", /* C14 */
+		"EMU0", /* B14 */
+		"WL_EN", /* K18 */
+		"WL_BT_OE", /* L18 */
+		"",
+		"",
+		"NC", /* F15 */
+		"SPI1_SCK", /* A13 */
+		"SPI1_MISO", /* B13 */
+		"SPI1_MOSI", /* D12 */
+		"GPIO3_17", /* C12 */
+		"EQEP_0A", /* B12 */
+		"EQEP_0B", /* C13 */
+		"GPIO3_20", /* D13 */
+		"IMU_INT", /* A14 */
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"";
+
 	ls-buf-en-hog {
 		gpio-hog;
 		gpios = <10 GPIO_ACTIVE_HIGH>;
 		output-high;
-		line-name = "LS_BUF_EN";
 	};
 };
 

arch/arm/boot/dts/am335x-bonegreen-wireless.dts

@@ -62,7 +62,7 @@
 	};
 };
 
-&mac {
+&mac_sw {
 	status = "disabled";
 };
 

arch/arm/boot/dts/am335x-chiliboard.dts

@@ -128,28 +128,31 @@
 };
 
 /* Ethernet */
-&mac {
-	slaves = <1>;
+&mac_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
 	status = "okay";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&davinci_mdio_default>;
 	pinctrl-1 = <&davinci_mdio_sleep>;
-	status = "okay";
 
 	ethphy0: ethernet-phy@0 {
 		reg = <0>;
 	};
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "rmii";
+	ti,dual-emac-pvid = <1>;
+};
+
+&cpsw_port2 {
+	status = "disabled";
 };
 
 /* USB */

arch/arm/boot/dts/am335x-cm-t335.dts

@@ -413,28 +413,31 @@ status = "okay";
 	status = "okay";
 };
 
-&mac {
+&mac_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
-	slaves = <1>;
 	status = "okay";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&davinci_mdio_default>;
 	pinctrl-1 = <&davinci_mdio_sleep>;
-	status = "okay";
 
 	ethphy0: ethernet-phy@0 {
 		reg = <0>;
 	};
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "rgmii-txid";
+	ti,dual-emac-pvid = <1>;
+};
+
+&cpsw_port2 {
+	status = "disabled";
 };
 
 &mmc1 {

arch/arm/boot/dts/am335x-evm.dts

@@ -778,3 +778,7 @@
 	clocks = <&clk_32768_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>;
 	clock-names = "ext-clk", "int-clk";
 };
+
+&pruss_tm {
+	status = "okay";
+};

arch/arm/boot/dts/am335x-evmsk.dts

@@ -715,3 +715,7 @@
 	clocks = <&clk_32768_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>;
 	clock-names = "ext-clk", "int-clk";
 };
+
+&pruss_tm {
+	status = "okay";
+};

arch/arm/boot/dts/am335x-icev2.dts

@@ -508,3 +508,7 @@
 		reg = <3>;
 	};
 };
+
+&pruss_tm {
+	status = "okay";
+};

arch/arm/boot/dts/am335x-igep0033.dtsi

@@ -93,12 +93,11 @@
 	};
 };
 
-&mac {
+&mac_sw {
 	status = "okay";
 };
 
-&davinci_mdio {
-	status = "okay";
+&davinci_mdio_sw {
 
 	ethphy0: ethernet-phy@0 {
 		reg = <0>;
@@ -109,15 +108,16 @@
 	};
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "rmii";
-
+	ti,dual-emac-pvid = <1>;
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-handle = <&ethphy1>;
 	phy-mode = "rmii";
+	ti,dual-emac-pvid = <2>;
 };
 
 &elm {

arch/arm/boot/dts/am335x-lxm.dts

@@ -295,31 +295,29 @@
 	dr_mode = "host";
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "rmii";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-handle = <&ethphy1>;
 	phy-mode = "rmii";
-	dual_emac_res_vlan = <3>;
+	ti,dual-emac-pvid = <3>;
 };
 
-&mac {
+&mac_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
-	dual_emac = <1>;
 	status = "okay";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&davinci_mdio_default>;
 	pinctrl-1 = <&davinci_mdio_sleep>;
-	status = "okay";
 
 	ethphy0: ethernet-phy@5 {
 		reg = <5>;

arch/arm/boot/dts/am335x-moxa-uc-2100-common.dtsi

@@ -122,24 +122,24 @@
 	regulator-max-microvolt = <5000000>;
 };
 
-&mac {
+&mac_sw {
 	pinctrl-names = "default";
 	pinctrl-0 = <&cpsw_default>;
 	status = "okay";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	pinctrl-names = "default";
 	pinctrl-0 = <&davinci_mdio_default>;
 	status = "okay";
 };
 
-&cpsw_emac0 {
-	status = "okay";
+&cpsw_port1 {
+	ti,dual-emac-pvid = <1>;
 };
 
-&cpsw_emac1 {
-	status = "okay";
+&cpsw_port2 {
+	ti,dual-emac-pvid = <2>;
 };
 
 &sham {

arch/arm/boot/dts/am335x-moxa-uc-2101.dts

@@ -52,18 +52,17 @@
 	};
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	phy0: ethernet-phy@4 {
 		reg = <4>;
 	};
 };
 
-&cpsw_emac0 {
-	status = "okay";
+&cpsw_port1 {
 	phy-handle = <&phy0>;
 	phy-mode = "rmii";
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	status = "disabled";
 };

arch/arm/boot/dts/am335x-moxa-uc-8100-common.dtsi

@@ -310,17 +310,15 @@
 	regulator-max-microvolt = <5000000>;
 };
 
-&mac {
+&mac_sw {
 	pinctrl-names = "default";
 	pinctrl-0 = <&cpsw_default>;
-	dual_emac = <1>;
 	status = "okay";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	pinctrl-names = "default";
 	pinctrl-0 = <&davinci_mdio_default>;
-	status = "okay";
 
 	ethphy0: ethernet-phy@4 {
 		reg = <4>;
@@ -331,18 +329,16 @@
 	};
 };
 
-&cpsw_emac0 {
-	status = "okay";
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "rmii";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <1>;
 };
 
-&cpsw_emac1 {
-	status = "okay";
+&cpsw_port2 {
 	phy-handle = <&ethphy1>;
 	phy-mode = "rmii";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 };
 
 &sham {

arch/arm/boot/dts/am335x-myirtech-myc.dtsi

@@ -57,16 +57,27 @@
 	};
 };
 
-&cpsw_emac0 {
+&mac_sw {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&eth_slave1_pins_default>;
+	pinctrl-1 = <&eth_slave1_pins_sleep>;
+	status = "okay";
+};
+
+&cpsw_port1 {
 	phy-handle = <&phy0>;
 	phy-mode = "rgmii-id";
+	ti,dual-emac-pvid = <1>;
+};
+
+&cpsw_port2 {
+	status = "disabled";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&mdio_pins_default>;
 	pinctrl-1 = <&mdio_pins_sleep>;
-	status = "okay";
 
 	phy0: ethernet-phy@4 {
 		reg = <4>;
@@ -137,14 +148,6 @@
 	};
 };
 
-&mac {
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&eth_slave1_pins_default>;
-	pinctrl-1 = <&eth_slave1_pins_sleep>;
-	slaves = <1>;
-	status = "okay";
-};
-
 &rtc {
 	system-power-controller;
 };

arch/arm/boot/dts/am335x-myirtech-myd.dts

@@ -86,18 +86,26 @@
 	};
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
+	status = "okay";
 	phy-handle = <&phy1>;
 	phy-mode = "rgmii-id";
+	ti,dual-emac-pvid = <2>;
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	phy1: ethernet-phy@6 {
 		reg = <6>;
 		eee-broken-1000t;
 	};
 };
 
+&mac_sw {
+	pinctrl-0 = <&eth_slave1_pins_default>, <&eth_slave2_pins_default>;
+	pinctrl-1 = <&eth_slave1_pins_sleep>, <&eth_slave2_pins_sleep>;
+	slaves = <2>;
+};
+
 &dcan0 {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&dcan0_pins_default>;
@@ -194,12 +202,6 @@
 	};
 };
 
-&mac {
-	pinctrl-0 = <&eth_slave1_pins_default>, <&eth_slave2_pins_default>;
-	pinctrl-1 = <&eth_slave1_pins_sleep>, <&eth_slave2_pins_sleep>;
-	slaves = <2>;
-};
-
 &mcasp0 {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&mcasp0_pins_default>;

arch/arm/boot/dts/am335x-nano.dts

@@ -369,12 +369,11 @@
 	};
 };
 
-&mac {
-	dual_emac;
+&mac_sw {
 	status = "okay";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	status = "okay";
 
 	ethphy0: ethernet-phy@0 {
@@ -386,16 +385,16 @@
 	};
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "mii";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <1>;
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-handle = <&ethphy1>;
 	phy-mode = "mii";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 };
 
 &mmc1 {

arch/arm/boot/dts/am335x-netcan-plus-1xx.dts

@@ -61,21 +61,21 @@
 	dr_mode = "host";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	phy0: ethernet-phy@0 {
 		reg = <1>;
 	};
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-mode = "rmii";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <1>;
 	phy-handle = <&phy0>;
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-mode = "rgmii-id";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 	phy-handle = <&phy1>;
 };
 

arch/arm/boot/dts/am335x-netcom-plus-2xx.dts

@@ -76,20 +76,20 @@
 	status = "okay";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	phy0: ethernet-phy@0 {
 		reg = <1>;
 	};
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-mode = "rmii";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <1>;
 	phy-handle = <&phy0>;
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-mode = "rgmii-id";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 	phy-handle = <&phy1>;
 };

arch/arm/boot/dts/am335x-netcom-plus-8xx.dts

@@ -96,20 +96,20 @@
 	};
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	phy0: ethernet-phy@0 {
 		reg = <1>;
 	};
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-mode = "rmii";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <1>;
 	phy-handle = <&phy0>;
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-mode = "rgmii-id";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 	phy-handle = <&phy1>;
 };

arch/arm/boot/dts/am335x-osd3358-sm-red.dts

@@ -391,24 +391,27 @@
 	clock-frequency = <100000>;
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "rgmii-txid";
+	ti,dual-emac-pvid = <1>;
 };
 
-&mac {
-	slaves = <1>;
+&cpsw_port2 {
+	status = "disabled";
+};
+
+&mac_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
 	status = "okay";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&davinci_mdio_default>;
 	pinctrl-1 = <&davinci_mdio_sleep>;
-	status = "okay";
 
 	ethphy0: ethernet-phy@4 {
 		reg = <4>;

arch/arm/boot/dts/am335x-pcm-953.dtsi

@@ -123,24 +123,22 @@
 	};
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-handle = <&phy1>;
 	phy-mode = "rgmii-id";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 	status = "okay";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	phy1: ethernet-phy@2 {
 		reg = <2>;
 	};
 };
 
-&mac {
-	slaves = <2>;
+&mac_sw {
 	pinctrl-names = "default";
 	pinctrl-0 = <&ethernet0_pins &ethernet1_pins>;
-	dual_emac;
 };
 
 /* Misc */

arch/arm/boot/dts/am335x-pdu001.dts

@@ -494,17 +494,15 @@
 	};
 };
 
-&mac {
+&mac_sw {
 	pinctrl-names = "default";
 	pinctrl-0 = <&cpsw_default>;
-	dual_emac;			/* no switch, two distinct MACs */
 	status = "okay";
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	pinctrl-names = "default";
 	pinctrl-0 = <&davinci_mdio_default>;
-	status = "okay";
 
 	ethphy0: ethernet-phy@0 {
 		reg = <0>;
@@ -515,16 +513,16 @@
 	};
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "mii";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <1>;
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-handle = <&ethphy1>;
 	phy-mode = "mii";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 };
 
 &tscadc {

arch/arm/boot/dts/am335x-pepper.dts

@@ -260,20 +260,19 @@
 };
 
 /* Ethernet */
-&cpsw_emac0 {
-	status = "okay";
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "rgmii";
+	ti,dual-emac-pvid = <1>;
 };
 
-&cpsw_emac1 {
-	status = "okay";
+&cpsw_port2 {
 	phy-handle = <&ethphy1>;
 	phy-mode = "rgmii";
+	ti,dual-emac-pvid = <2>;
 };
 
-&davinci_mdio {
-	status = "okay";
+&davinci_mdio_sw {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mdio_pins>;
 
@@ -286,13 +285,12 @@
 	};
 };
 
-&mac {
+&mac_sw {
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&ethernet_pins>;
 };
 
-
 &am33xx_pinmux {
 	ethernet_pins: pinmux_ethernet {
 		pinctrl-single,pins = <

arch/arm/boot/dts/am335x-phycore-som.dtsi

@@ -97,24 +97,26 @@
 	};
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&phy0>;
 	phy-mode = "rmii";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <1>;
 };
 
-&davinci_mdio {
+&cpsw_port2 {
+	status = "disabled";
+};
+
+&davinci_mdio_sw {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mdio_pins>;
-	status = "okay";
 
 	phy0: ethernet-phy@0 {
 		reg = <0>;
 	};
 };
 
-&mac {
-	slaves = <1>;
+&mac_sw {
 	pinctrl-names = "default";
 	pinctrl-0 = <&ethernet0_pins>;
 	status = "okay";

arch/arm/boot/dts/am335x-regor.dtsi

@@ -85,23 +85,22 @@
 	};
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
+	status = "okay";
 	phy-handle = <&phy1>;
 	phy-mode = "mii";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	phy1: ethernet-phy@1 {
 		reg = <1>;
 	};
 };
 
-&mac {
-	slaves = <2>;
+&mac_sw {
 	pinctrl-names = "default";
 	pinctrl-0 = <&ethernet0_pins &ethernet1_pins>;
-	dual_emac = <1>;
 };
 
 /* GPIOs */

arch/arm/boot/dts/am335x-sancloud-bbe-common.dtsi

+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+&am33xx_pinmux {
+	cpsw_default: cpsw_default {
+		pinctrl-single,pins = <
+			/* Slave 1 */
+			AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_OUTPUT_PULLDOWN, MUX_MODE2)	/* mii1_txen.rgmii1_tctl */
+			AM33XX_PADCONF(AM335X_PIN_MII1_RX_DV, PIN_INPUT_PULLDOWN, MUX_MODE2)	/* mii1_rxdv.rgmii1_rctl */
+			AM33XX_PADCONF(AM335X_PIN_MII1_TXD3, PIN_OUTPUT_PULLDOWN, MUX_MODE2)	/* mii1_txd3.rgmii1_td3 */
+			AM33XX_PADCONF(AM335X_PIN_MII1_TXD2, PIN_OUTPUT_PULLDOWN, MUX_MODE2)	/* mii1_txd2.rgmii1_td2 */
+			AM33XX_PADCONF(AM335X_PIN_MII1_TXD1, PIN_OUTPUT_PULLDOWN, MUX_MODE2)	/* mii1_txd1.rgmii1_td1 */
+			AM33XX_PADCONF(AM335X_PIN_MII1_TXD0, PIN_OUTPUT_PULLDOWN, MUX_MODE2)	/* mii1_txd0.rgmii1_td0 */
+			AM33XX_PADCONF(AM335X_PIN_MII1_TX_CLK, PIN_OUTPUT_PULLDOWN, MUX_MODE2)	/* mii1_txclk.rgmii1_tclk */
+			AM33XX_PADCONF(AM335X_PIN_MII1_RX_CLK, PIN_INPUT_PULLDOWN, MUX_MODE2)	/* mii1_rxclk.rgmii1_rclk */
+			AM33XX_PADCONF(AM335X_PIN_MII1_RXD3, PIN_INPUT_PULLDOWN, MUX_MODE2)	/* mii1_rxd3.rgmii1_rd3 */
+			AM33XX_PADCONF(AM335X_PIN_MII1_RXD2, PIN_INPUT_PULLDOWN, MUX_MODE2)	/* mii1_rxd2.rgmii1_rd2 */
+			AM33XX_PADCONF(AM335X_PIN_MII1_RXD1, PIN_INPUT_PULLDOWN, MUX_MODE2)	/* mii1_rxd1.rgmii1_rd1 */
+			AM33XX_PADCONF(AM335X_PIN_MII1_RXD0, PIN_INPUT_PULLDOWN, MUX_MODE2)	/* mii1_rxd0.rgmii1_rd0 */
+		>;
+	};
+
+	cpsw_sleep: cpsw_sleep {
+		pinctrl-single,pins = <
+			/* Slave 1 reset value */
+			AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_RX_DV, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_TXD3, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_TXD2, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_TXD1, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_TXD0, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_TX_CLK, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_RX_CLK, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_RXD3, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_RXD2, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_RXD1, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_RXD0, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+	};
+
+	usb_hub_ctrl: usb_hub_ctrl {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_RMII1_REF_CLK, PIN_OUTPUT_PULLUP, MUX_MODE7)     /* rmii1_refclk.gpio0_29 */
+		>;
+	};
+};
+
+&mac_sw {
+	pinctrl-0 = <&cpsw_default>;
+	pinctrl-1 = <&cpsw_sleep>;
+};
+
+&cpsw_port1 {
+	phy-mode = "rgmii-id";
+};
+
+&i2c0 {
+	usb2512b: usb-hub@2c {
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb_hub_ctrl>;
+		compatible = "microchip,usb2512b";
+		reg = <0x2c>;
+		reset-gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
+	};
+};

arch/arm/boot/dts/am335x-sancloud-bbe-lite.dts

+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2021 SanCloud Ltd
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+#include "am335x-bone-common.dtsi"
+#include "am335x-boneblack-common.dtsi"
+#include "am335x-sancloud-bbe-common.dtsi"
+
+/ {
+	model = "SanCloud BeagleBone Enhanced Lite";
+	compatible = "sancloud,am335x-boneenhanced",
+		     "ti,am335x-bone-black",
+		     "ti,am335x-bone",
+		     "ti,am33xx";
+};
+
+&am33xx_pinmux {
+	bb_spi0_pins: pinmux_bb_spi0_pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_SPI0_SCLK, PIN_INPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_SPI0_D0, PIN_INPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_SPI0_D1, PIN_INPUT, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_SPI0_CS0, PIN_INPUT, MUX_MODE0)
+		>;
+	};
+};
+
+&spi0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&bb_spi0_pins>;
+
+	channel@0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		compatible = "micron,spi-authenta";
+
+		reg = <0>;
+		spi-max-frequency = <16000000>;
+		spi-cpha;
+	};
+};

arch/arm/boot/dts/am335x-sancloud-bbe.dts

@@ -7,6 +7,8 @@
 #include "am33xx.dtsi"
 #include "am335x-bone-common.dtsi"
 #include "am335x-boneblack-common.dtsi"
+#include "am335x-boneblack-hdmi.dtsi"
+#include "am335x-sancloud-bbe-common.dtsi"
 #include <dt-bindings/interrupt-controller/irq.h>
 
 / {
@@ -15,66 +17,6 @@
 };
 
 &am33xx_pinmux {
-	pinctrl-names = "default";
-
-	cpsw_default: cpsw_default {
-		pinctrl-single,pins = <
-			/* Slave 1 */
-			AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_OUTPUT_PULLDOWN, MUX_MODE2)	/* mii1_txen.rgmii1_tctl */
-			AM33XX_PADCONF(AM335X_PIN_MII1_RX_DV, PIN_INPUT_PULLDOWN, MUX_MODE2)	/* mii1_rxdv.rgmii1_rctl */
-			AM33XX_PADCONF(AM335X_PIN_MII1_TXD3, PIN_OUTPUT_PULLDOWN, MUX_MODE2)	/* mii1_txd3.rgmii1_td3 */
-			AM33XX_PADCONF(AM335X_PIN_MII1_TXD2, PIN_OUTPUT_PULLDOWN, MUX_MODE2)	/* mii1_txd2.rgmii1_td2 */
-			AM33XX_PADCONF(AM335X_PIN_MII1_TXD1, PIN_OUTPUT_PULLDOWN, MUX_MODE2)	/* mii1_txd1.rgmii1_td1 */
-			AM33XX_PADCONF(AM335X_PIN_MII1_TXD0, PIN_OUTPUT_PULLDOWN, MUX_MODE2)	/* mii1_txd0.rgmii1_td0 */
-			AM33XX_PADCONF(AM335X_PIN_MII1_TX_CLK, PIN_OUTPUT_PULLDOWN, MUX_MODE2)	/* mii1_txclk.rgmii1_tclk */
-			AM33XX_PADCONF(AM335X_PIN_MII1_RX_CLK, PIN_INPUT_PULLDOWN, MUX_MODE2)	/* mii1_rxclk.rgmii1_rclk */
-			AM33XX_PADCONF(AM335X_PIN_MII1_RXD3, PIN_INPUT_PULLDOWN, MUX_MODE2)	/* mii1_rxd3.rgmii1_rd3 */
-			AM33XX_PADCONF(AM335X_PIN_MII1_RXD2, PIN_INPUT_PULLDOWN, MUX_MODE2)	/* mii1_rxd2.rgmii1_rd2 */
-			AM33XX_PADCONF(AM335X_PIN_MII1_RXD1, PIN_INPUT_PULLDOWN, MUX_MODE2)	/* mii1_rxd1.rgmii1_rd1 */
-			AM33XX_PADCONF(AM335X_PIN_MII1_RXD0, PIN_INPUT_PULLDOWN, MUX_MODE2)	/* mii1_rxd0.rgmii1_rd0 */
-		>;
-	};
-
-	cpsw_sleep: cpsw_sleep {
-		pinctrl-single,pins = <
-			/* Slave 1 reset value */
-			AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_INPUT_PULLDOWN, MUX_MODE7)
-			AM33XX_PADCONF(AM335X_PIN_MII1_RX_DV, PIN_INPUT_PULLDOWN, MUX_MODE7)
-			AM33XX_PADCONF(AM335X_PIN_MII1_TXD3, PIN_INPUT_PULLDOWN, MUX_MODE7)
-			AM33XX_PADCONF(AM335X_PIN_MII1_TXD2, PIN_INPUT_PULLDOWN, MUX_MODE7)
-			AM33XX_PADCONF(AM335X_PIN_MII1_TXD1, PIN_INPUT_PULLDOWN, MUX_MODE7)
-			AM33XX_PADCONF(AM335X_PIN_MII1_TXD0, PIN_INPUT_PULLDOWN, MUX_MODE7)
-			AM33XX_PADCONF(AM335X_PIN_MII1_TX_CLK, PIN_INPUT_PULLDOWN, MUX_MODE7)
-			AM33XX_PADCONF(AM335X_PIN_MII1_RX_CLK, PIN_INPUT_PULLDOWN, MUX_MODE7)
-			AM33XX_PADCONF(AM335X_PIN_MII1_RXD3, PIN_INPUT_PULLDOWN, MUX_MODE7)
-			AM33XX_PADCONF(AM335X_PIN_MII1_RXD2, PIN_INPUT_PULLDOWN, MUX_MODE7)
-			AM33XX_PADCONF(AM335X_PIN_MII1_RXD1, PIN_INPUT_PULLDOWN, MUX_MODE7)
-			AM33XX_PADCONF(AM335X_PIN_MII1_RXD0, PIN_INPUT_PULLDOWN, MUX_MODE7)
-		>;
-	};
-
-	davinci_mdio_default: davinci_mdio_default {
-		pinctrl-single,pins = <
-			/* MDIO */
-			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLUP | SLEWCTRL_FAST, MUX_MODE0)
-			AM33XX_PADCONF(AM335X_PIN_MDC, PIN_OUTPUT_PULLUP, MUX_MODE0)
-		>;
-	};
-
-	davinci_mdio_sleep: davinci_mdio_sleep {
-		pinctrl-single,pins = <
-			/* MDIO reset value */
-			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLDOWN, MUX_MODE7)
-			AM33XX_PADCONF(AM335X_PIN_MDC, PIN_INPUT_PULLDOWN, MUX_MODE7)
-		>;
-	};
-
-	usb_hub_ctrl: usb_hub_ctrl {
-		pinctrl-single,pins = <
-			AM33XX_PADCONF(AM335X_PIN_RMII1_REF_CLK, PIN_OUTPUT_PULLUP, MUX_MODE7)     /* rmii1_refclk.gpio0_29 */
-		>;
-	};
-
 	mpu6050_pins: pinmux_mpu6050_pins {
 		pinctrl-single,pins = <
 			AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_INPUT, MUX_MODE7)    /* uart0_ctsn.gpio1_8 */
@@ -88,31 +30,10 @@
 	};
 };
 
-&mac {
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&cpsw_default>;
-	pinctrl-1 = <&cpsw_sleep>;
-	status = "okay";
-};
-
-&davinci_mdio {
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&davinci_mdio_default>;
-	pinctrl-1 = <&davinci_mdio_sleep>;
-	status = "okay";
-
-	ethphy0: ethernet-phy@0 {
-		reg = <0>;
-	};
-};
-
-&cpsw_emac0 {
-	phy-handle = <&ethphy0>;
-	phy-mode = "rgmii-id";
-};
-
 &i2c0 {
 	lps331ap: barometer@5c {
+		pinctrl-names = "default";
+		pinctrl-0 = <&lps3331ap_pins>;
 		compatible = "st,lps331ap-press";
 		st,drdy-int-pin = <1>;
 		reg = <0x5c>;
@@ -121,17 +42,12 @@
 	};
 
 	mpu6050: accelerometer@68 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&mpu6050_pins>;
 		compatible = "invensense,mpu6050";
 		reg = <0x68>;
 		interrupt-parent = <&gpio0>;
 		interrupts = <2 IRQ_TYPE_EDGE_RISING>;
 		orientation = <0xff 0 0 0 1 0 0 0 0xff>;
 	};
-
-	usb2512b: usb-hub@2c {
-		compatible = "microchip,usb2512b";
-		reg = <0x2c>;
-		reset-gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
-		/* wifi on port 4 */
-	};
 };

arch/arm/boot/dts/am335x-shc.dts

@@ -117,18 +117,6 @@
 	status = "okay";
 };
 
-&davinci_mdio {
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&davinci_mdio_default>;
-	pinctrl-1 = <&davinci_mdio_sleep>;
-	status = "okay";
-
-	ethernetphy0: ethernet-phy@0 {
-		reg = <0>;
-		smsc,disable-energy-detect;
-	};
-};
-
 &epwmss1 {
 	status = "okay";
 
@@ -193,15 +181,31 @@
 	};
 };
 
-&mac {
+&mac_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
 	status = "okay";
-	slaves = <1>;
-	cpsw_emac0: slave@200 {
-		phy-mode = "mii";
-		phy-handle = <&ethernetphy0>;
+};
+
+&cpsw_port1 {
+	phy-mode = "mii";
+	phy-handle = <&ethernetphy0>;
+	ti,dual-emac-pvid = <1>;
+};
+
+&cpsw_port2 {
+	status = "disabled";
+};
+
+&davinci_mdio_sw {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&davinci_mdio_default>;
+	pinctrl-1 = <&davinci_mdio_sleep>;
+
+	ethernetphy0: ethernet-phy@0 {
+		reg = <0>;
+		smsc,disable-energy-detect;
 	};
 };
 

arch/arm/boot/dts/am335x-sl50.dts

@@ -661,20 +661,24 @@
 	};
 };
 
-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-mode = "mii";
 	phy-handle = <&ethphy0>;
+	ti,dual-emac-pvid = <1>;
 };
 
-&mac {
+&cpsw_port2 {
+	status = "disabled";
+};
+
+&mac_sw {
 	status = "okay";
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
 };
 
-&davinci_mdio {
-	status = "okay";
+&davinci_mdio_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&davinci_mdio_default>;
 	pinctrl-1 = <&davinci_mdio_sleep>;

arch/arm/boot/dts/am335x-wega.dtsi

@@ -111,23 +111,22 @@
 	};
 };
 
-&cpsw_emac1 {
+&cpsw_port2 {
+	status = "okay";
 	phy-handle = <&phy1>;
 	phy-mode = "mii";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 };
 
-&davinci_mdio {
+&davinci_mdio_sw {
 	phy1: ethernet-phy@1 {
 		reg = <1>;
 	};
 };
 
-&mac {
-	slaves = <2>;
+&mac_sw {
 	pinctrl-names = "default";
 	pinctrl-0 = <&ethernet0_pins &ethernet1_pins>;
-	dual_emac = <1>;
 };
 
 /* MMC */

arch/arm/boot/dts/am33xx-l4.dtsi

@@ -853,6 +853,88 @@
 			#size-cells = <1>;
 			ranges = <0x0 0x300000 0x80000>;
 			status = "disabled";
+
+			pruss: pruss@0 {
+				compatible = "ti,am3356-pruss";
+				reg = <0x0 0x80000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges;
+
+				pruss_mem: memories@0 {
+					reg = <0x0 0x2000>,
+					      <0x2000 0x2000>,
+					      <0x10000 0x3000>;
+					reg-names = "dram0", "dram1",
+						    "shrdram2";
+				};
+
+				pruss_cfg: cfg@26000 {
+					compatible = "ti,pruss-cfg", "syscon";
+					reg = <0x26000 0x2000>;
+					#address-cells = <1>;
+					#size-cells = <1>;
+					ranges = <0x0 0x26000 0x2000>;
+
+					clocks {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						pruss_iepclk_mux: iepclk-mux@30 {
+							reg = <0x30>;
+							#clock-cells = <0>;
+							clocks = <&l3_gclk>,        /* icss_iep_gclk */
+								 <&pruss_ocp_gclk>; /* icss_ocp_gclk */
+						};
+					};
+				};
+
+				pruss_mii_rt: mii-rt@32000 {
+					compatible = "ti,pruss-mii", "syscon";
+					reg = <0x32000 0x58>;
+				};
+
+				pruss_intc: interrupt-controller@20000 {
+					compatible = "ti,pruss-intc";
+					reg = <0x20000 0x2000>;
+					interrupts = <20 21 22 23 24 25 26 27>;
+					interrupt-names = "host_intr0", "host_intr1",
+							  "host_intr2", "host_intr3",
+							  "host_intr4", "host_intr5",
+							  "host_intr6", "host_intr7";
+					interrupt-controller;
+					#interrupt-cells = <3>;
+				};
+
+				pru0: pru@34000 {
+					compatible = "ti,am3356-pru";
+					reg = <0x34000 0x2000>,
+					      <0x22000 0x400>,
+					      <0x22400 0x100>;
+					reg-names = "iram", "control", "debug";
+					firmware-name = "am335x-pru0-fw";
+				};
+
+				pru1: pru@38000 {
+					compatible = "ti,am3356-pru";
+					reg = <0x38000 0x2000>,
+					      <0x24000 0x400>,
+					      <0x24400 0x100>;
+					reg-names = "iram", "control", "debug";
+					firmware-name = "am335x-pru1-fw";
+				};
+
+				pruss_mdio: mdio@32400 {
+					compatible = "ti,davinci_mdio";
+					reg = <0x32400 0x90>;
+					clocks = <&dpll_core_m4_ck>;
+					clock-names = "fck";
+					bus_freq = <1000000>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					status = "disabled";
+				};
+			};
 		};
 	};
 };

arch/arm/boot/dts/am33xx.dtsi

@@ -36,8 +36,8 @@
 		usb1 = &usb1;
 		phy0 = &usb0_phy;
 		phy1 = &usb1_phy;
-		ethernet0 = &cpsw_emac0;
-		ethernet1 = &cpsw_emac1;
+		ethernet0 = &cpsw_port1;
+		ethernet1 = &cpsw_port2;
 		spi0 = &spi0;
 		spi1 = &spi1;
 		mmc0 = &mmc1;

arch/arm/boot/dts/am4372.dtsi

@@ -434,6 +434,171 @@
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x54400000 0x80000>;
+
+			pruss1: pruss@0 {
+				compatible = "ti,am4376-pruss1";
+				reg = <0x0 0x40000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges;
+
+				pruss1_mem: memories@0 {
+					reg = <0x0 0x2000>,
+					      <0x2000 0x2000>,
+					      <0x10000 0x8000>;
+					reg-names = "dram0", "dram1",
+						    "shrdram2";
+				};
+
+				pruss1_cfg: cfg@26000 {
+					compatible = "ti,pruss-cfg", "syscon";
+					reg = <0x26000 0x2000>;
+					#address-cells = <1>;
+					#size-cells = <1>;
+					ranges = <0x0 0x26000 0x2000>;
+
+					clocks {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						pruss1_iepclk_mux: iepclk-mux@30 {
+							reg = <0x30>;
+							#clock-cells = <0>;
+							clocks = <&sysclk_div>,     /* icss_iep_gclk */
+								 <&pruss_ocp_gclk>; /* icss_ocp_gclk */
+						};
+					};
+				};
+
+				pruss1_mii_rt: mii-rt@32000 {
+					compatible = "ti,pruss-mii", "syscon";
+					reg = <0x32000 0x58>;
+				};
+
+				pruss1_intc: interrupt-controller@20000 {
+					compatible = "ti,pruss-intc";
+					reg = <0x20000 0x2000>;
+					interrupt-controller;
+					#interrupt-cells = <3>;
+					interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "host_intr0", "host_intr1",
+							  "host_intr2", "host_intr3",
+							  "host_intr4",
+							  "host_intr6", "host_intr7";
+					ti,irqs-reserved = /bits/ 8 <0x20>; /* BIT(5) */
+				};
+
+				pru1_0: pru@34000 {
+					compatible = "ti,am4376-pru";
+					reg = <0x34000 0x3000>,
+					      <0x22000 0x400>,
+					      <0x22400 0x100>;
+					reg-names = "iram", "control", "debug";
+					firmware-name = "am437x-pru1_0-fw";
+				};
+
+				pru1_1: pru@38000 {
+					compatible = "ti,am4376-pru";
+					reg = <0x38000 0x3000>,
+					      <0x24000 0x400>,
+					      <0x24400 0x100>;
+					reg-names = "iram", "control", "debug";
+					firmware-name = "am437x-pru1_1-fw";
+				};
+
+				pruss1_mdio: mdio@32400 {
+					compatible = "ti,davinci_mdio";
+					reg = <0x32400 0x90>;
+					clocks = <&dpll_core_m4_ck>;
+					clock-names = "fck";
+					bus_freq = <1000000>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+			};
+
+			pruss0: pruss@40000 {
+				compatible = "ti,am4376-pruss0";
+				reg = <0x40000 0x40000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges;
+
+				pruss0_mem: memories@40000 {
+					reg = <0x40000 0x1000>,
+					      <0x42000 0x1000>;
+					reg-names = "dram0", "dram1";
+				};
+
+				pruss0_cfg: cfg@66000 {
+					compatible = "ti,pruss-cfg", "syscon";
+					reg = <0x66000 0x2000>;
+					#address-cells = <1>;
+					#size-cells = <1>;
+					ranges = <0x0 0x66000 0x2000>;
+
+					clocks {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						pruss0_iepclk_mux: iepclk-mux@30 {
+							reg = <0x30>;
+							#clock-cells = <0>;
+							clocks = <&sysclk_div>,     /* icss_iep_gclk */
+								 <&pruss_ocp_gclk>; /* icss_ocp_gclk */
+						};
+					};
+				};
+
+				pruss0_mii_rt: mii-rt@72000 {
+					compatible = "ti,pruss-mii", "syscon";
+					reg = <0x72000 0x58>;
+					status = "disabled";
+				};
+
+				pruss0_intc: interrupt-controller@60000 {
+					compatible = "ti,pruss-intc";
+					reg = <0x60000 0x2000>;
+					interrupt-controller;
+					#interrupt-cells = <3>;
+					interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "host_intr0", "host_intr1",
+							  "host_intr2", "host_intr3",
+							  "host_intr4",
+							  "host_intr6", "host_intr7";
+					ti,irqs-reserved = /bits/ 8 <0x20>; /* BIT(5) */
+				};
+
+				pru0_0: pru@74000 {
+					compatible = "ti,am4376-pru";
+					reg = <0x74000 0x1000>,
+					      <0x62000 0x400>,
+					      <0x62400 0x100>;
+					reg-names = "iram", "control", "debug";
+					firmware-name = "am437x-pru0_0-fw";
+				};
+
+				pru0_1: pru@78000 {
+					compatible = "ti,am4376-pru";
+					reg = <0x78000 0x1000>,
+					      <0x64000 0x400>,
+					      <0x64400 0x100>;
+					reg-names = "iram", "control", "debug";
+					firmware-name = "am437x-pru0_1-fw";
+				};
+			};
 		};
 
 		target-module@50000000 {

arch/arm/boot/dts/am437x-cm-t43.dts

@@ -416,3 +416,7 @@
 			   <600000 1100000>,
 			   <300000 950000>;
 };
+
+&pruss1_mdio {
+	status = "disabled";
+};

arch/arm/boot/dts/am437x-gp-evm.dts

@@ -1118,3 +1118,7 @@
 &cpu {
 	cpu0-supply = <&dcdc2>;
 };
+
+&pruss1_mdio {
+	status = "disabled";
+};

arch/arm/boot/dts/am437x-idk-evm.dts

@@ -537,3 +537,7 @@
 		opp-suspend;
 	};
 };
+
+&pruss1_mdio {
+	status = "disabled";
+};

arch/arm/boot/dts/am437x-sk-evm.dts

@@ -892,3 +892,7 @@
 		};
 	};
 };
+
+&pruss1_mdio {
+	status = "disabled";
+};

arch/arm/boot/dts/am43x-epos-evm.dts

@@ -1018,3 +1018,7 @@
 &cpu {
 	cpu0-supply = <&dcdc2>;
 };
+
+&pruss1_mdio {
+	status = "disabled";
+};

arch/arm/boot/dts/am57-pruss.dtsi

 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Copyright (C) 2020 Texas Instruments Incorporated - https://www.ti.com/
+ * Copyright (C) 2020-2021 Texas Instruments Incorporated - https://www.ti.com/
  *
  * Common PRUSS data for TI AM57xx platforms
  */
@@ -25,6 +25,94 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00000000 0x4b200000 0x80000>;
+
+		pruss1: pruss@0 {
+			compatible = "ti,am5728-pruss";
+			reg = <0x0 0x80000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			pruss1_mem: memories@0 {
+				reg = <0x0 0x2000>,
+				      <0x2000 0x2000>,
+				      <0x10000 0x8000>;
+				reg-names = "dram0", "dram1",
+					    "shrdram2";
+			};
+
+			pruss1_cfg: cfg@26000 {
+				compatible = "ti,pruss-cfg", "syscon";
+				reg = <0x26000 0x2000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x26000 0x2000>;
+
+				clocks {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					pruss1_iepclk_mux: iepclk-mux@30 {
+						reg = <0x30>;
+						#clock-cells = <0>;
+						clocks = <&dpll_gmac_m3x2_ck>,  /* icss_iep_clk */
+							 <&dpll_gmac_h13x2_ck>; /* icss_clk */
+					};
+				};
+			};
+
+			pruss1_mii_rt: mii-rt@32000 {
+				compatible = "ti,pruss-mii", "syscon";
+				reg = <0x32000 0x58>;
+			};
+
+			pruss1_intc: interrupt-controller@20000 {
+				compatible = "ti,pruss-intc";
+				reg = <0x20000 0x2000>;
+				interrupt-controller;
+				#interrupt-cells = <3>;
+				interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "host_intr0", "host_intr1",
+						  "host_intr2", "host_intr3",
+						  "host_intr4", "host_intr5",
+						  "host_intr6", "host_intr7";
+			};
+
+			pru1_0: pru@34000 {
+				compatible = "ti,am5728-pru";
+				reg = <0x34000 0x3000>,
+				      <0x22000 0x400>,
+				      <0x22400 0x100>;
+				reg-names = "iram", "control", "debug";
+				firmware-name = "am57xx-pru1_0-fw";
+			};
+
+			pru1_1: pru@38000 {
+				compatible = "ti,am5728-pru";
+				reg = <0x38000 0x3000>,
+				      <0x24000 0x400>,
+				      <0x24400 0x100>;
+				reg-names = "iram", "control", "debug";
+				firmware-name = "am57xx-pru1_1-fw";
+			};
+
+			pruss1_mdio: mdio@32400 {
+				compatible = "ti,davinci_mdio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&dpll_gmac_h13x2_ck>;
+				clock-names = "fck";
+				bus_freq = <1000000>;
+				reg = <0x32400 0x90>;
+			};
+		};
 	};
 
 	pruss2_tm: target-module@4b2a6000 {
@@ -46,5 +134,93 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x00000000 0x4b280000 0x80000>;
+
+		pruss2: pruss@0 {
+			compatible = "ti,am5728-pruss";
+			reg = <0x0 0x80000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			pruss2_mem: memories@0 {
+				reg = <0x0 0x2000>,
+				      <0x2000 0x2000>,
+				      <0x10000 0x8000>;
+				reg-names = "dram0", "dram1",
+					    "shrdram2";
+			};
+
+			pruss2_cfg: cfg@26000 {
+				compatible = "ti,pruss-cfg", "syscon";
+				reg = <0x26000 0x2000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x26000 0x2000>;
+
+				clocks {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					pruss2_iepclk_mux: iepclk-mux@30 {
+						reg = <0x30>;
+						#clock-cells = <0>;
+						clocks = <&dpll_gmac_m3x2_ck>,  /* icss_iep_clk */
+							 <&dpll_gmac_h13x2_ck>; /* icss_clk */
+					};
+				};
+			};
+
+			pruss2_mii_rt: mii-rt@32000 {
+				compatible = "ti,pruss-mii", "syscon";
+				reg = <0x32000 0x58>;
+			};
+
+			pruss2_intc: interrupt-controller@20000 {
+				compatible = "ti,pruss-intc";
+				reg = <0x20000 0x2000>;
+				interrupt-controller;
+				#interrupt-cells = <3>;
+				interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "host_intr0", "host_intr1",
+						  "host_intr2", "host_intr3",
+						  "host_intr4", "host_intr5",
+						  "host_intr6", "host_intr7";
+			};
+
+			pru2_0: pru@34000 {
+				compatible = "ti,am5728-pru";
+				reg = <0x34000 0x3000>,
+				      <0x22000 0x400>,
+				      <0x22400 0x100>;
+				reg-names = "iram", "control", "debug";
+				firmware-name = "am57xx-pru2_0-fw";
+			};
+
+			pru2_1: pru@38000 {
+				compatible = "ti,am5728-pru";
+				reg = <0x38000 0x3000>,
+				      <0x24000 0x400>,
+				      <0x24400 0x100>;
+				reg-names = "iram", "control", "debug";
+				firmware-name = "am57xx-pru2_1-fw";
+			};
+
+			pruss2_mdio: mdio@32400 {
+				compatible = "ti,davinci_mdio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&dpll_gmac_h13x2_ck>;
+				clock-names = "fck";
+				bus_freq = <1000000>;
+				reg = <0x32400 0x90>;
+			};
+		};
 	};
 };

arch/arm/boot/dts/am571x-idk.dts

@@ -208,3 +208,11 @@
 	pinctrl-1 = <&mmc2_pins_hs>;
 	pinctrl-2 = <&mmc2_pins_ddr_rev20 &mmc2_iodelay_ddr_conf>;
 };
+
+&pruss1_mdio {
+	status = "disabled";
+};
+
+&pruss2_mdio {
+	status = "disabled";
+};

arch/arm/boot/dts/am572x-idk.dts

@@ -27,3 +27,11 @@
 	pinctrl-1 = <&mmc2_pins_hs>;
 	pinctrl-2 = <&mmc2_pins_ddr_rev20>;
 };
+
+&pruss1_mdio {
+	status = "disabled";
+};
+
+&pruss2_mdio {
+	status = "disabled";
+};

arch/arm/boot/dts/am5748.dtsi

@@ -3,7 +3,7 @@
  * Copyright (C) 2019 Texas Instruments Incorporated - https://www.ti.com/
  */
 
-#include "dra76x.dtsi"
+#include "dra74x-p.dtsi"
 #include "am57-pruss.dtsi"
 
 / {
@@ -25,10 +25,6 @@
 	status = "disabled";
 };
 
-&usb4_tm {
-	status = "disabled";
-};
-
 &atl_tm {
 	status = "disabled";
 };

arch/arm/boot/dts/am574x-idk.dts

@@ -36,10 +36,14 @@
 	pinctrl-2 = <&mmc2_pins_default>;
 };
 
-&m_can0 {
+&emif1 {
+	status = "okay";
+};
+
+&pruss1_mdio {
 	status = "disabled";
 };
 
-&emif1 {
-	status = "okay";
+&pruss2_mdio {
+	status = "disabled";
 };

arch/arm/boot/dts/am57xx-beagle-x15-common.dtsi

@@ -637,3 +637,11 @@
 	status = "okay";
 	memory-region = <&dsp2_memory_region>;
 };
+
+&pruss1_mdio {
+	status = "disabled";
+};
+
+&pruss2_mdio {
+	status = "disabled";
+};

arch/arm/boot/dts/am57xx-cl-som-am57x.dts

@@ -618,3 +618,11 @@
 	status = "okay";
 	ti,no-reset-on-init;
 };
+
+&pruss1_mdio {
+	status = "disabled";
+};
+
+&pruss2_mdio {
+	status = "disabled";
+};

arch/arm/boot/dts/aspeed-ast2500-evb.dts

@@ -129,3 +129,7 @@
      status = "okay";
      memory-region = <&gfx_memory>;
 };
+
+&rtc {
+	status = "okay";
+};

arch/arm/boot/dts/aspeed-bmc-facebook-cloudripper.dts

+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2020 Facebook Inc.
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include "ast2600-facebook-netbmc-common.dtsi"
+
+/ {
+	model = "Facebook Cloudripper BMC";
+	compatible = "facebook,cloudripper-bmc", "aspeed,ast2600";
+
+	aliases {
+		/*
+		 * PCA9548 (1-0070) provides 8 channels connecting to
+		 * SMB (Switch Main Board).
+		 */
+		i2c16 = &imux16;
+		i2c17 = &imux17;
+		i2c18 = &imux18;
+		i2c19 = &imux19;
+		i2c20 = &imux20;
+		i2c21 = &imux21;
+		i2c22 = &imux22;
+		i2c23 = &imux23;
+
+		/*
+		 * PCA9548 (2-0070) provides 8 channels connecting to
+		 * SCM (System Controller Module).
+		 */
+		i2c24 = &imux24;
+		i2c25 = &imux25;
+		i2c26 = &imux26;
+		i2c27 = &imux27;
+		i2c28 = &imux28;
+		i2c29 = &imux29;
+		i2c30 = &imux30;
+		i2c31 = &imux31;
+
+		/*
+		 * PCA9548 (3-0070) provides 8 channels connecting to
+		 * SMB (Switch Main Board).
+		 */
+		i2c32 = &imux32;
+		i2c33 = &imux33;
+		i2c34 = &imux34;
+		i2c35 = &imux35;
+		i2c36 = &imux36;
+		i2c37 = &imux37;
+		i2c38 = &imux38;
+		i2c39 = &imux39;
+
+		/*
+		 * PCA9548 (8-0070) provides 8 channels connecting to
+		 * PDB (Power Delivery Board).
+		 */
+		i2c40 = &imux40;
+		i2c41 = &imux41;
+		i2c42 = &imux42;
+		i2c43 = &imux43;
+		i2c44 = &imux44;
+		i2c45 = &imux45;
+		i2c46 = &imux46;
+		i2c47 = &imux47;
+
+		/*
+		 * PCA9548 (15-0076) provides 8 channels connecting to
+		 * FCM (Fan Controller Module).
+		 */
+		i2c48 = &imux48;
+		i2c49 = &imux49;
+		i2c50 = &imux50;
+		i2c51 = &imux51;
+		i2c52 = &imux52;
+		i2c53 = &imux53;
+		i2c54 = &imux54;
+		i2c55 = &imux55;
+	};
+
+	spi_gpio: spi-gpio {
+		num-chipselects = <2>;
+		cs-gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>,
+			   <&gpio0 ASPEED_GPIO(X, 1) GPIO_ACTIVE_HIGH>;
+
+		eeprom@1 {
+			compatible = "atmel,at93c46d";
+			spi-max-frequency = <250000>;
+			data-size = <16>;
+			spi-cs-high;
+			reg = <1>;
+		};
+	};
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+/*
+ * "mdio1" is connected to the MDC/MDIO interface of the on-board
+ * management switch (whose ports are connected to BMC, Host and front
+ * panel ethernet port).
+ */
+&mdio1 {
+	status = "okay";
+};
+
+&mdio3 {
+	status = "okay";
+
+	ethphy1: ethernet-phy@13 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x0d>;
+	};
+};
+
+&mac3 {
+	status = "okay";
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii4_default>;
+};
+
+&i2c0 {
+	multi-master;
+	bus-frequency = <1000000>;
+};
+
+&i2c1 {
+	/*
+	 * PCA9548 (1-0070) provides 8 channels connecting to SMB (Switch
+	 * Main Board).
+	 */
+	i2c-switch@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		imux16: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		imux17: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		imux18: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux19: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+
+		imux20: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		imux21: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		imux22: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		imux23: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+&i2c2 {
+	/*
+	 * PCA9548 (2-0070) provides 8 channels connecting to SCM (System
+	 * Controller Module).
+	 */
+	i2c-switch@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		imux24: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		imux25: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		imux26: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux27: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+
+		imux28: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		imux29: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		imux30: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		imux31: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+&i2c3 {
+	/*
+	 * PCA9548 (3-0070) provides 8 channels connecting to SMB (Switch
+	 * Main Board).
+	 */
+	i2c-switch@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		imux32: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		imux33: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		imux34: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux35: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+
+		imux36: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		imux37: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		imux38: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		imux39: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+&i2c6 {
+	lp5012@14 {
+		compatible = "ti,lp5012";
+		reg = <0x14>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		multi-led@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			color = <LED_COLOR_ID_MULTI>;
+			function = LED_FUNCTION_ACTIVITY;
+			label = "sys";
+
+			led@0 {
+				reg = <0>;
+				color = <LED_COLOR_ID_RED>;
+			};
+
+			led@1 {
+				reg = <1>;
+				color = <LED_COLOR_ID_BLUE>;
+			};
+
+			led@2 {
+				reg = <2>;
+				color = <LED_COLOR_ID_GREEN>;
+			};
+		};
+
+		multi-led@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			color = <LED_COLOR_ID_MULTI>;
+			function = LED_FUNCTION_ACTIVITY;
+			label = "fan";
+
+			led@0 {
+				reg = <0>;
+				color = <LED_COLOR_ID_RED>;
+			};
+
+			led@1 {
+				reg = <1>;
+				color = <LED_COLOR_ID_BLUE>;
+			};
+
+			led@2 {
+				reg = <2>;
+				color = <LED_COLOR_ID_GREEN>;
+			};
+		};
+
+		multi-led@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			color = <LED_COLOR_ID_MULTI>;
+			function = LED_FUNCTION_ACTIVITY;
+			label = "psu";
+
+			led@0 {
+				reg = <0>;
+				color = <LED_COLOR_ID_RED>;
+			};
+
+			led@1 {
+				reg = <1>;
+				color = <LED_COLOR_ID_BLUE>;
+			};
+
+			led@2 {
+				reg = <2>;
+				color = <LED_COLOR_ID_GREEN>;
+			};
+		};
+
+		multi-led@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+			color = <LED_COLOR_ID_MULTI>;
+			function = LED_FUNCTION_ACTIVITY;
+			label = "scm";
+
+			led@0 {
+				reg = <0>;
+				color = <LED_COLOR_ID_RED>;
+			};
+
+			led@1 {
+				reg = <1>;
+				color = <LED_COLOR_ID_BLUE>;
+			};
+
+			led@2 {
+				reg = <2>;
+				color = <LED_COLOR_ID_GREEN>;
+			};
+		};
+	};
+};
+
+&i2c8 {
+	/*
+	 * PCA9548 (8-0070) provides 8 channels connecting to PDB (Power
+	 * Delivery Board).
+	 */
+	i2c-switch@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		imux40: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		imux41: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		imux42: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux43: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+
+		imux44: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		imux45: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		imux46: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		imux47: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+
+	};
+};
+
+&i2c15 {
+	/*
+	 * PCA9548 (15-0076) provides 8 channels connecting to FCM (Fan
+	 * Controller Module).
+	 */
+	i2c-switch@76 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x76>;
+		i2c-mux-idle-disconnect;
+
+		imux48: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		imux49: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		imux50: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux51: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+
+		imux52: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		imux53: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		imux54: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		imux55: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+	};
+};

arch/arm/boot/dts/aspeed-bmc-facebook-elbert.dts

+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2020 Facebook Inc.
+
+/dts-v1/;
+
+#include "ast2600-facebook-netbmc-common.dtsi"
+
+/ {
+	model = "Facebook Elbert BMC";
+	compatible = "facebook,elbert-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial0 = &uart5;
+		serial1 = &uart1;
+		serial2 = &uart2;
+		serial3 = &uart3;
+
+		/*
+		 * 8 child channels of PCA9548 2-0075.
+		 */
+		i2c16 = &imux16;
+		i2c17 = &imux17;
+		i2c18 = &imux18;
+		i2c19 = &imux19;
+		i2c20 = &imux20;
+		i2c21 = &imux21;
+		i2c22 = &imux22;
+		i2c23 = &imux23;
+
+		/*
+		 * 8 child channels of PCA9548 5-0075.
+		 */
+		i2c24 = &imux24;
+		i2c25 = &imux25;
+		i2c26 = &imux26;
+		i2c27 = &imux27;
+		i2c28 = &imux28;
+		i2c29 = &imux29;
+		i2c30 = &imux30;
+		i2c31 = &imux31;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+	};
+
+	spi_gpio: spi-gpio {
+		num-chipselects = <1>;
+		cs-gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>;
+	};
+};
+
+&lpc_ctrl {
+	status = "okay";
+};
+
+&kcs2 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca8>;
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+};
+
+&i2c2 {
+	i2c-switch@75 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+		i2c-mux-idle-disconnect;
+
+		imux16: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		imux17: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		imux18: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux19: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+
+		imux20: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		imux21: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		imux22: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		imux23: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+&i2c5 {
+	i2c-switch@75 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+		i2c-mux-idle-disconnect;
+
+		imux24: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		imux25: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		imux26: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		imux27: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+
+		imux28: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		imux29: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		imux30: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		imux31: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+&i2c11 {
+	status = "okay";
+};

arch/arm/boot/dts/aspeed-bmc-facebook-galaxy100.dts

@@ -51,7 +51,3 @@
 &vhub {
 	status = "okay";
 };
-
-&adc {
-	status = "okay";
-};

arch/arm/boot/dts/aspeed-bmc-facebook-minipack.dts

@@ -265,19 +265,19 @@
 		};
 
 		/*
-		 * FIT image: 59.5 MB.
+		 * FIT image: 55.5 MB.
 		 */
 		fit@80000 {
-			reg = <0x80000 0x3b80000>;
+			reg = <0x80000 0x3780000>;
 			label = "fit";
 		};
 
 		/*
-		 * "data0" partition (4MB) is reserved for persistent
+		 * "data0" partition (8MB) is reserved for persistent
 		 * data store.
 		 */
 		data0@3800000 {
-			reg = <0x3c00000 0x400000>;
+			reg = <0x3800000 0x800000>;
 			label = "data0";
 		};
 

arch/arm/boot/dts/aspeed-bmc-facebook-wedge100.dts

@@ -12,6 +12,11 @@
 		stdout-path = &uart3;
 		bootargs = "console=ttyS2,9600n8 root=/dev/ram rw";
 	};
+
+	ast-adc-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 5>, <&adc 6>, <&adc 7>, <&adc 8>, <&adc 9>;
+	};
 };
 
 &wdt2 {

arch/arm/boot/dts/aspeed-bmc-facebook-wedge40.dts

@@ -23,10 +23,6 @@
 	status = "disabled";
 };
 
-&adc {
-	status = "okay";
-};
-
 &pwm_tacho {
 	status = "okay";
 	pinctrl-names = "default";

arch/arm/boot/dts/aspeed-bmc-facebook-wedge400.dts

@@ -91,53 +91,7 @@
  * Both firmware flashes are 128MB on Wedge400 BMC.
  */
 &fmc_flash0 {
-	partitions {
-		compatible = "fixed-partitions";
-		#address-cells = <1>;
-		#size-cells = <1>;
-
-		/*
-		 * u-boot partition: 384KB.
-		 */
-		u-boot@0 {
-			reg = <0x0 0x60000>;
-			label = "u-boot";
-		};
-
-		/*
-		 * u-boot environment variables: 128KB.
-		 */
-		u-boot-env@60000 {
-			reg = <0x60000 0x20000>;
-			label = "env";
-		};
-
-		/*
-		 * FIT image: 123.5 MB.
-		 */
-		fit@80000 {
-			reg = <0x80000 0x7b80000>;
-			label = "fit";
-		};
-
-		/*
-		 * "data0" partition (4MB) is reserved for persistent
-		 * data store.
-		 */
-		data0@7c00000 {
-			reg = <0x7c00000 0x400000>;
-			label = "data0";
-		};
-
-		/*
-		 * "flash0" partition (covering the entire flash) is
-		 * explicitly created to avoid breaking legacy applications.
-		 */
-		flash0@0 {
-			reg = <0x0 0x8000000>;
-			label = "flash0";
-		};
-	};
+#include "facebook-bmc-flash-layout-128.dtsi"
 };
 
 &fmc_flash1 {

arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts

@@ -253,7 +253,7 @@
 	/*O0-O7*/	"","","","","","","","",
 	/*P0-P7*/	"","","","","led-pcieslot-power","","","",
 	/*Q0-Q7*/	"","","","","","","","",
-	/*R0-R7*/	"","","","","","I2C_FLASH_MICRO_N","","",
+	/*R0-R7*/	"bmc-tpm-reset","power-chassis-control","power-chassis-good","","","I2C_FLASH_MICRO_N","","",
 	/*S0-S7*/	"","","","","","","","",
 	/*T0-T7*/	"","","","","","","","",
 	/*U0-U7*/	"","","","","","","","",
@@ -303,7 +303,7 @@
 			type = <PCA955X_TYPE_GPIO>;
 		};
 
-		gpio@01 {
+		gpio@1 {
 			reg = <1>;
 			type = <PCA955X_TYPE_GPIO>;
 		};
@@ -2832,7 +2832,7 @@
 
 &emmc {
 	status = "okay";
-	clk-phase-mmc-hs200 = <180>, <180>;
+	clk-phase-mmc-hs200 = <210>, <228>;
 };
 
 &fsim0 {

arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts

@@ -271,7 +271,7 @@
 	/*O0-O7*/	"","","","usb-power","","","","",
 	/*P0-P7*/	"","","","","pcieslot-power","","","",
 	/*Q0-Q7*/	"cfam-reset","","","","","","","",
-	/*R0-R7*/	"","","","","","","","",
+	/*R0-R7*/	"bmc-tpm-reset","power-chassis-control","power-chassis-good","","","","","",
 	/*S0-S7*/	"presence-ps0","presence-ps1","presence-ps2","presence-ps3",
 				"","","","",
 	/*T0-T7*/	"","","","","","","","",

arch/arm/boot/dts/aspeed-bmc-opp-tacoma.dts

@@ -126,7 +126,7 @@
 	/*M0-M7*/	"","","","","","","","",
 	/*N0-N7*/	"","","","","","","","",
 	/*O0-O7*/	"led-rear-power","led-rear-id","","usb-power","","","","",
-	/*P0-P7*/	"","","","","","","","",
+	/*P0-P7*/	"","","","","","bmc-tpm-reset","","",
 	/*Q0-Q7*/	"cfam-reset","","","","","","","fsi-routing",
 	/*R0-R7*/	"","","","","","","","",
 	/*S0-S7*/	"","","","","","","","",

arch/arm/boot/dts/aspeed-g5.dtsi

@@ -352,7 +352,6 @@
 				reg = <0x1e780200 0x0100>;
 				clocks = <&syscon ASPEED_CLK_APB>;
 				interrupt-controller;
-				ngpios = <8>;
 				bus-frequency = <12000000>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_sgpm_default>;

arch/arm/boot/dts/aspeed-g6-pinctrl.dtsi

@@ -208,12 +208,12 @@
 	};
 
 	pinctrl_hvi3c3_default: hvi3c3_default {
-		function = "HVI3C3";
+		function = "I3C3";
 		groups = "HVI3C3";
 	};
 
 	pinctrl_hvi3c4_default: hvi3c4_default {
-		function = "HVI3C4";
+		function = "I3C4";
 		groups = "HVI3C4";
 	};
 

arch/arm/boot/dts/aspeed-g6.dtsi

@@ -377,6 +377,34 @@
 				#interrupt-cells = <2>;
 			};
 
+			sgpiom0: sgpiom@1e780500 {
+				#gpio-cells = <2>;
+				gpio-controller;
+				compatible = "aspeed,ast2600-sgpiom";
+				reg = <0x1e780500 0x100>;
+				interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&syscon ASPEED_CLK_APB2>;
+				interrupt-controller;
+				bus-frequency = <12000000>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_sgpm1_default>;
+				status = "disabled";
+			};
+
+			sgpiom1: sgpiom@1e780600 {
+				#gpio-cells = <2>;
+				gpio-controller;
+				compatible = "aspeed,ast2600-sgpiom";
+				reg = <0x1e780600 0x100>;
+				interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&syscon ASPEED_CLK_APB2>;
+				interrupt-controller;
+				bus-frequency = <12000000>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_sgpm2_default>;
+				status = "disabled";
+			};
+
 			gpio1: gpio@1e780800 {
 				#gpio-cells = <2>;
 				gpio-controller;

arch/arm/boot/dts/ast2400-facebook-netbmc-common.dtsi

@@ -115,3 +115,7 @@
 &vhub {
 	status = "okay";
 };
+
+&adc {
+	status = "okay";
+};

arch/arm/boot/dts/at91-kizbox3_common.dtsi

@@ -336,7 +336,7 @@
 };
 
 &shutdown_controller {
-	atmel,shdwc-debouncer = <976>;
+	debounce-delay-us = <976>;
 	atmel,wakeup-rtc-timer;
 
 	input@0 {

arch/arm/boot/dts/at91-sama5d27_wlsom1_ek.dts

@@ -205,7 +205,7 @@
 };
 
 &shutdown_controller {
-	atmel,shdwc-debouncer = <976>;
+	debounce-delay-us = <976>;
 	atmel,wakeup-rtc-timer;
 
 	input@0 {