Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
提交 7940a34b 编写于 作者: K Kevin Hilman
浏览文件
操作

Merge branch 'davinci-next' into davinci-for-linus 

Conflicts:
	arch/arm/mach-davinci/board-da830-evm.c
	arch/arm/mach-davinci/board-da850-evm.c
上级 6451d778 8939b350
展开全部 隐藏空白更改
内联 并排
Showing with 3814 addition and 1359 deletion
MAINTAINERS
浏览文件 @ 7940a34b
......@@ -5303,8 +5303,8 @@ F: drivers/*/*s3c2410*
F: drivers/*/*/*s3c2410*
TI DAVINCI MACHINE SUPPORT
P: Kevin Hilman
M: davinci-linux-open-source@linux.davincidsp.com
M: Kevin Hilman <khilman@deeprootsystems.com>
L: davinci-linux-open-source@linux.davincidsp.com (subscribers-only)
Q: http://patchwork.kernel.org/project/linux-davinci/list/
S: Supported
F: arch/arm/mach-davinci
......
arch/arm/configs/da8xx_omapl_defconfig
浏览文件 @ 7940a34b
......@@ -17,6 +17,8 @@ CONFIG_MODVERSIONS=y
CONFIG_ARCH_DAVINCI=y
CONFIG_ARCH_DAVINCI_DA830=y
CONFIG_ARCH_DAVINCI_DA850=y
CONFIG_MACH_MITYOMAPL138=y
CONFIG_MACH_OMAPL138_HAWKBOARD=y
CONFIG_DAVINCI_RESET_CLOCKS=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
......@@ -79,6 +81,7 @@ CONFIG_I2C_DAVINCI=y
# CONFIG_HWMON is not set
CONFIG_WATCHDOG=y
CONFIG_REGULATOR=y
CONFIG_REGULATOR_DUMMY=y
CONFIG_REGULATOR_TPS6507X=y
CONFIG_FB=y
CONFIG_FB_DA8XX=y
......
arch/arm/mach-davinci/Kconfig
浏览文件 @ 7940a34b
......@@ -20,23 +20,23 @@ config ARCH_DAVINCI_DM644x
select ARCH_DAVINCI_DMx
config ARCH_DAVINCI_DM355
bool "DaVinci 355 based system"
bool "DaVinci 355 based system"
select AINTC
select ARCH_DAVINCI_DMx
config ARCH_DAVINCI_DM646x
bool "DaVinci 646x based system"
bool "DaVinci 646x based system"
select AINTC
select ARCH_DAVINCI_DMx
config ARCH_DAVINCI_DA830
bool "DA830/OMAP-L137 based system"
bool "DA830/OMAP-L137/AM17x based system"
select CP_INTC
select ARCH_DAVINCI_DA8XX
select CPU_DCACHE_WRITETHROUGH # needed on silicon revs 1.0, 1.1
config ARCH_DAVINCI_DA850
bool "DA850/OMAP-L138 based system"
bool "DA850/OMAP-L138/AM18x based system"
select CP_INTC
select ARCH_DAVINCI_DA8XX
select ARCH_HAS_CPUFREQ
......@@ -115,21 +115,21 @@ config MACH_DAVINCI_DM365_EVM
for development is a DM365 EVM
config MACH_DAVINCI_DA830_EVM
bool "TI DA830/OMAP-L137 Reference Platform"
bool "TI DA830/OMAP-L137/AM17x Reference Platform"
default ARCH_DAVINCI_DA830
depends on ARCH_DAVINCI_DA830
select GPIO_PCF857X
help
Say Y here to select the TI DA830/OMAP-L137 Evaluation Module.
Say Y here to select the TI DA830/OMAP-L137/AM17x Evaluation Module.
choice
prompt "Select DA830/OMAP-L137 UI board peripheral"
prompt "Select DA830/OMAP-L137/AM17x UI board peripheral"
depends on MACH_DAVINCI_DA830_EVM
help
The presence of UI card on the DA830/OMAP-L137 EVM is detected
automatically based on successful probe of the I2C based GPIO
expander on that board. This option selected in this menu has
an effect only in case of a successful UI card detection.
The presence of UI card on the DA830/OMAP-L137/AM17x EVM is
detected automatically based on successful probe of the I2C
based GPIO expander on that board. This option selected in this
menu has an effect only in case of a successful UI card detection.
config DA830_UI_LCD
bool "LCD"
......@@ -140,23 +140,23 @@ config DA830_UI_LCD
config DA830_UI_NAND
bool "NAND flash"
help
Say Y here to use the NAND flash. Do not forget to setup
Say Y here to use the NAND flash. Do not forget to setup
the switch correctly.
endchoice
config MACH_DAVINCI_DA850_EVM
bool "TI DA850/OMAP-L138 Reference Platform"
bool "TI DA850/OMAP-L138/AM18x Reference Platform"
default ARCH_DAVINCI_DA850
depends on ARCH_DAVINCI_DA850
select GPIO_PCA953X
help
Say Y here to select the TI DA850/OMAP-L138 Evaluation Module.
Say Y here to select the TI DA850/OMAP-L138/AM18x Evaluation Module.
choice
prompt "Select peripherals connected to expander on UI board"
depends on MACH_DAVINCI_DA850_EVM
help
The presence of User Interface (UI) card on the DA850/OMAP-L138
The presence of User Interface (UI) card on the DA850/OMAP-L138/AM18x
EVM is detected automatically based on successful probe of the I2C
based GPIO expander on that card. This option selected in this
menu has an effect only in case of a successful UI card detection.
......@@ -165,13 +165,13 @@ config DA850_UI_NONE
bool "No peripheral is enabled"
help
Say Y if you do not want to enable any of the peripherals connected
to TCA6416 expander on DA850/OMAP-L138 EVM UI card
to TCA6416 expander on DA850/OMAP-L138/AM18x EVM UI card
config DA850_UI_RMII
bool "RMII Ethernet PHY"
help
Say Y if you want to use the RMII PHY on the DA850/OMAP-L138 EVM.
This PHY is found on the UI daughter card that is supplied with
Say Y if you want to use the RMII PHY on the DA850/OMAP-L138/AM18x
EVM. This PHY is found on the UI daughter card that is supplied with
the EVM.
NOTE: Please take care while choosing this option, MII PHY will
not be functional if RMII mode is selected.
......@@ -185,6 +185,22 @@ config MACH_TNETV107X
help
Say Y here to select the TI TNETV107X Evaluation Module.
config MACH_MITYOMAPL138
bool "Critical Link MityDSP-L138/MityARM-1808 SoM"
depends on ARCH_DAVINCI_DA850
help
Say Y here to select the Critical Link MityDSP-L138/MityARM-1808
System on Module. Information on this SoM may be found at
http://www.mitydsp.com
config MACH_OMAPL138_HAWKBOARD
bool "TI AM1808 / OMAPL-138 Hawkboard platform"
depends on ARCH_DAVINCI_DA850
help
Say Y here to select the TI AM1808 / OMAPL-138 Hawkboard platform .
Information of this board may be found at
http://www.hawkboard.org/
config DAVINCI_MUX
bool "DAVINCI multiplexing support"
depends on ARCH_DAVINCI
......@@ -195,20 +211,20 @@ config DAVINCI_MUX
say Y.
config DAVINCI_MUX_DEBUG
bool "Multiplexing debug output"
depends on DAVINCI_MUX
help
Makes the multiplexing functions print out a lot of debug info.
This is useful if you want to find out the correct values of the
multiplexing registers.
bool "Multiplexing debug output"
depends on DAVINCI_MUX
help
Makes the multiplexing functions print out a lot of debug info.
This is useful if you want to find out the correct values of the
multiplexing registers.
config DAVINCI_MUX_WARNINGS
bool "Warn about pins the bootloader didn't set up"
depends on DAVINCI_MUX
help
Choose Y here to warn whenever driver initialization logic needs
to change the pin multiplexing setup. When there are no warnings
printed, it's safe to deselect DAVINCI_MUX for your product.
bool "Warn about pins the bootloader didn't set up"
depends on DAVINCI_MUX
help
Choose Y here to warn whenever driver initialization logic needs
to change the pin multiplexing setup. When there are no warnings
printed, it's safe to deselect DAVINCI_MUX for your product.
config DAVINCI_RESET_CLOCKS
bool "Reset unused clocks during boot"
......
arch/arm/mach-davinci/Makefile
浏览文件 @ 7940a34b
......@@ -5,7 +5,7 @@
# Common objects
obj-y := time.o clock.o serial.o io.o psc.o \
gpio.o dma.o usb.o common.o sram.o
gpio.o dma.o usb.o common.o sram.o aemif.o
obj-$(CONFIG_DAVINCI_MUX) += mux.o
......@@ -33,6 +33,8 @@ obj-$(CONFIG_MACH_DAVINCI_DM365_EVM) += board-dm365-evm.o
obj-$(CONFIG_MACH_DAVINCI_DA830_EVM) += board-da830-evm.o
obj-$(CONFIG_MACH_DAVINCI_DA850_EVM) += board-da850-evm.o
obj-$(CONFIG_MACH_TNETV107X) += board-tnetv107x-evm.o
obj-$(CONFIG_MACH_MITYOMAPL138) += board-mityomapl138.o
obj-$(CONFIG_MACH_OMAPL138_HAWKBOARD) += board-omapl138-hawk.o
# Power Management
obj-$(CONFIG_CPU_FREQ) += cpufreq.o
......
arch/arm/mach-davinci/aemif.c 0 → 100644
浏览文件 @ 7940a34b
/*
* AEMIF support for DaVinci SoCs
*
* Copyright (C) 2010 Texas Instruments Incorporated. http://www.ti.com/
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/kernel.h>
#include <linux/io.h>
#include <linux/err.h>
#include <linux/clk.h>
#include <linux/module.h>
#include <linux/time.h>
#include <mach/aemif.h>
/* Timing value configuration */
#define TA(x) ((x) << 2)
#define RHOLD(x) ((x) << 4)
#define RSTROBE(x) ((x) << 7)
#define RSETUP(x) ((x) << 13)
#define WHOLD(x) ((x) << 17)
#define WSTROBE(x) ((x) << 20)
#define WSETUP(x) ((x) << 26)
#define TA_MAX 0x3
#define RHOLD_MAX 0x7
#define RSTROBE_MAX 0x3f
#define RSETUP_MAX 0xf
#define WHOLD_MAX 0x7
#define WSTROBE_MAX 0x3f
#define WSETUP_MAX 0xf
#define TIMING_MASK (TA(TA_MAX) | \
RHOLD(RHOLD_MAX) | \
RSTROBE(RSTROBE_MAX) | \
RSETUP(RSETUP_MAX) | \
WHOLD(WHOLD_MAX) | \
WSTROBE(WSTROBE_MAX) | \
WSETUP(WSETUP_MAX))
/*
* aemif_calc_rate - calculate timing data.
* @wanted: The cycle time needed in nanoseconds.
* @clk: The input clock rate in kHz.
* @max: The maximum divider value that can be programmed.
*
* On success, returns the calculated timing value minus 1 for easy
* programming into AEMIF timing registers, else negative errno.
*/
static int aemif_calc_rate(int wanted, unsigned long clk, int max)
{
int result;
result = DIV_ROUND_UP((wanted * clk), NSEC_PER_MSEC) - 1;
pr_debug("%s: result %d from %ld, %d\n", __func__, result, clk, wanted);
/* It is generally OK to have a more relaxed timing than requested... */
if (result < 0)
result = 0;
/* ... But configuring tighter timings is not an option. */
else if (result > max)
result = -EINVAL;
return result;
}
/**
* davinci_aemif_setup_timing - setup timing values for a given AEMIF interface
* @t: timing values to be progammed
* @base: The virtual base address of the AEMIF interface
* @cs: chip-select to program the timing values for
*
* This function programs the given timing values (in real clock) into the
* AEMIF registers taking the AEMIF clock into account.
*
* This function does not use any locking while programming the AEMIF
* because it is expected that there is only one user of a given
* chip-select.
*
* Returns 0 on success, else negative errno.
*/
int davinci_aemif_setup_timing(struct davinci_aemif_timing *t,
void __iomem *base, unsigned cs)
{
unsigned set, val;
unsigned ta, rhold, rstrobe, rsetup, whold, wstrobe, wsetup;
unsigned offset = A1CR_OFFSET + cs * 4;
struct clk *aemif_clk;
unsigned long clkrate;
if (!t)
return 0; /* Nothing to do */
aemif_clk = clk_get(NULL, "aemif");
if (IS_ERR(aemif_clk))
return PTR_ERR(aemif_clk);
clkrate = clk_get_rate(aemif_clk);
clkrate /= 1000; /* turn clock into kHz for ease of use */
ta = aemif_calc_rate(t->ta, clkrate, TA_MAX);
rhold = aemif_calc_rate(t->rhold, clkrate, RHOLD_MAX);
rstrobe = aemif_calc_rate(t->rstrobe, clkrate, RSTROBE_MAX);
rsetup = aemif_calc_rate(t->rsetup, clkrate, RSETUP_MAX);
whold = aemif_calc_rate(t->whold, clkrate, WHOLD_MAX);
wstrobe = aemif_calc_rate(t->wstrobe, clkrate, WSTROBE_MAX);
wsetup = aemif_calc_rate(t->wsetup, clkrate, WSETUP_MAX);
if (ta < 0 || rhold < 0 || rstrobe < 0 || rsetup < 0 ||
whold < 0 || wstrobe < 0 || wsetup < 0) {
pr_err("%s: cannot get suitable timings\n", __func__);
return -EINVAL;
}
set = TA(ta) | RHOLD(rhold) | RSTROBE(rstrobe) | RSETUP(rsetup) |
WHOLD(whold) | WSTROBE(wstrobe) | WSETUP(wsetup);
val = __raw_readl(base + offset);
val &= ~TIMING_MASK;
val |= set;
__raw_writel(val, base + offset);
return 0;
}
EXPORT_SYMBOL(davinci_aemif_setup_timing);
arch/arm/mach-davinci/board-da830-evm.c
浏览文件 @ 7940a34b
......@@ -29,10 +29,9 @@
#include <mach/nand.h>
#include <mach/da8xx.h>
#include <mach/usb.h>
#include <mach/aemif.h>
#define DA830_EVM_PHY_MASK 0x0
#define DA830_EVM_MDIO_FREQUENCY 2200000 /* PHY bus frequency */
#define DA830_EVM_PHY_ID ""
/*
* USB1 VBUS is controlled by GPIO1[15], over-current is reported on GPIO2[4].
*/
......@@ -360,6 +359,16 @@ static struct nand_bbt_descr da830_evm_nand_bbt_mirror_descr = {
.pattern = da830_evm_nand_mirror_pattern
};
static struct davinci_aemif_timing da830_evm_nandflash_timing = {
.wsetup = 24,
.wstrobe = 21,
.whold = 14,
.rsetup = 19,
.rstrobe = 50,
.rhold = 0,
.ta = 20,
};
static struct davinci_nand_pdata da830_evm_nand_pdata = {
.parts = da830_evm_nand_partitions,
.nr_parts = ARRAY_SIZE(da830_evm_nand_partitions),
......@@ -368,6 +377,7 @@ static struct davinci_nand_pdata da830_evm_nand_pdata = {
.options = NAND_USE_FLASH_BBT,
.bbt_td = &da830_evm_nand_bbt_main_descr,
.bbt_md = &da830_evm_nand_bbt_mirror_descr,
.timing = &da830_evm_nandflash_timing,
};
static struct resource da830_evm_nand_resources[] = {
......@@ -546,9 +556,8 @@ static __init void da830_evm_init(void)
da830_evm_usb_init();
soc_info->emac_pdata->phy_mask = DA830_EVM_PHY_MASK;
soc_info->emac_pdata->mdio_max_freq = DA830_EVM_MDIO_FREQUENCY;
soc_info->emac_pdata->rmii_en = 1;
soc_info->emac_pdata->phy_id = DA830_EVM_PHY_ID;
ret = davinci_cfg_reg_list(da830_cpgmac_pins);
if (ret)
......@@ -586,6 +595,9 @@ static __init void da830_evm_init(void)
#ifdef CONFIG_SERIAL_8250_CONSOLE
static int __init da830_evm_console_init(void)
{
if (!machine_is_davinci_da830_evm())
return 0;
return add_preferred_console("ttyS", 2, "115200");
}
console_initcall(da830_evm_console_init);
......@@ -596,7 +608,7 @@ static void __init da830_evm_map_io(void)
da830_init();
}
MACHINE_START(DAVINCI_DA830_EVM, "DaVinci DA830/OMAP-L137 EVM")
MACHINE_START(DAVINCI_DA830_EVM, "DaVinci DA830/OMAP-L137/AM17x EVM")
.boot_params = (DA8XX_DDR_BASE + 0x100),
.map_io = da830_evm_map_io,
.init_irq = cp_intc_init,
......
arch/arm/mach-davinci/board-da850-evm.c
浏览文件 @ 7940a34b
......@@ -26,7 +26,6 @@
#include <linux/mtd/physmap.h>
#include <linux/regulator/machine.h>
#include <linux/regulator/tps6507x.h>
#include <linux/mfd/tps6507x.h>
#include <linux/input/tps6507x-ts.h>
#include <asm/mach-types.h>
......@@ -36,10 +35,9 @@
#include <mach/da8xx.h>
#include <mach/nand.h>
#include <mach/mux.h>
#include <mach/aemif.h>
#define DA850_EVM_PHY_MASK 0x1
#define DA850_EVM_MDIO_FREQUENCY 2200000 /* PHY bus frequency */
#define DA850_EVM_PHY_ID "0:00"
#define DA850_LCD_PWR_PIN GPIO_TO_PIN(2, 8)
#define DA850_LCD_BL_PIN GPIO_TO_PIN(2, 15)
......@@ -110,7 +108,7 @@ static struct platform_device da850_pm_device = {
* to boot, using TI's tools to install the secondary boot loader
* (UBL) and U-Boot.
*/
struct mtd_partition da850_evm_nandflash_partition[] = {
static struct mtd_partition da850_evm_nandflash_partition[] = {
{
.name = "u-boot env",
.offset = 0,
......@@ -143,12 +141,23 @@ struct mtd_partition da850_evm_nandflash_partition[] = {
},
};
static struct davinci_aemif_timing da850_evm_nandflash_timing = {
.wsetup = 24,
.wstrobe = 21,
.whold = 14,
.rsetup = 19,
.rstrobe = 50,
.rhold = 0,
.ta = 20,
};
static struct davinci_nand_pdata da850_evm_nandflash_data = {
.parts = da850_evm_nandflash_partition,
.nr_parts = ARRAY_SIZE(da850_evm_nandflash_partition),
.ecc_mode = NAND_ECC_HW,
.ecc_bits = 4,
.options = NAND_USE_FLASH_BBT,
.timing = &da850_evm_nandflash_timing,
};
static struct resource da850_evm_nandflash_resource[] = {
......@@ -196,6 +205,30 @@ static void __init da850_evm_init_nor(void)
iounmap(aemif_addr);
}
static const short da850_evm_nand_pins[] = {
DA850_EMA_D_0, DA850_EMA_D_1, DA850_EMA_D_2, DA850_EMA_D_3,
DA850_EMA_D_4, DA850_EMA_D_5, DA850_EMA_D_6, DA850_EMA_D_7,
DA850_EMA_A_1, DA850_EMA_A_2, DA850_NEMA_CS_3, DA850_NEMA_CS_4,
DA850_NEMA_WE, DA850_NEMA_OE,
-1
};
static const short da850_evm_nor_pins[] = {
DA850_EMA_BA_1, DA850_EMA_CLK, DA850_EMA_WAIT_1, DA850_NEMA_CS_2,
DA850_NEMA_WE, DA850_NEMA_OE, DA850_EMA_D_0, DA850_EMA_D_1,
DA850_EMA_D_2, DA850_EMA_D_3, DA850_EMA_D_4, DA850_EMA_D_5,
DA850_EMA_D_6, DA850_EMA_D_7, DA850_EMA_D_8, DA850_EMA_D_9,
DA850_EMA_D_10, DA850_EMA_D_11, DA850_EMA_D_12, DA850_EMA_D_13,
DA850_EMA_D_14, DA850_EMA_D_15, DA850_EMA_A_0, DA850_EMA_A_1,
DA850_EMA_A_2, DA850_EMA_A_3, DA850_EMA_A_4, DA850_EMA_A_5,
DA850_EMA_A_6, DA850_EMA_A_7, DA850_EMA_A_8, DA850_EMA_A_9,
DA850_EMA_A_10, DA850_EMA_A_11, DA850_EMA_A_12, DA850_EMA_A_13,
DA850_EMA_A_14, DA850_EMA_A_15, DA850_EMA_A_16, DA850_EMA_A_17,
DA850_EMA_A_18, DA850_EMA_A_19, DA850_EMA_A_20, DA850_EMA_A_21,
DA850_EMA_A_22, DA850_EMA_A_23,
-1
};
static u32 ui_card_detected;
#if defined(CONFIG_MMC_DAVINCI) || \
......@@ -205,17 +238,17 @@ static u32 ui_card_detected;
#define HAS_MMC 0
#endif
static __init void da850_evm_setup_nor_nand(void)
static inline void da850_evm_setup_nor_nand(void)
{
int ret = 0;
if (ui_card_detected & !HAS_MMC) {
ret = davinci_cfg_reg_list(da850_nand_pins);
ret = davinci_cfg_reg_list(da850_evm_nand_pins);
if (ret)
pr_warning("da850_evm_init: nand mux setup failed: "
"%d\n", ret);
ret = davinci_cfg_reg_list(da850_nor_pins);
ret = davinci_cfg_reg_list(da850_evm_nor_pins);
if (ret)
pr_warning("da850_evm_init: nor mux setup failed: %d\n",
ret);
......@@ -406,7 +439,7 @@ static int da850_lcd_hw_init(void)
/* TPS65070 voltage regulator support */
/* 3.3V */
struct regulator_consumer_supply tps65070_dcdc1_consumers[] = {
static struct regulator_consumer_supply tps65070_dcdc1_consumers[] = {
{
.supply = "usb0_vdda33",
},
......@@ -416,7 +449,7 @@ struct regulator_consumer_supply tps65070_dcdc1_consumers[] = {
};
/* 3.3V or 1.8V */
struct regulator_consumer_supply tps65070_dcdc2_consumers[] = {
static struct regulator_consumer_supply tps65070_dcdc2_consumers[] = {
{
.supply = "dvdd3318_a",
},
......@@ -429,14 +462,14 @@ struct regulator_consumer_supply tps65070_dcdc2_consumers[] = {
};
/* 1.2V */
struct regulator_consumer_supply tps65070_dcdc3_consumers[] = {
static struct regulator_consumer_supply tps65070_dcdc3_consumers[] = {
{
.supply = "cvdd",
},
};
/* 1.8V LDO */
struct regulator_consumer_supply tps65070_ldo1_consumers[] = {
static struct regulator_consumer_supply tps65070_ldo1_consumers[] = {
{
.supply = "sata_vddr",
},
......@@ -452,7 +485,7 @@ struct regulator_consumer_supply tps65070_ldo1_consumers[] = {
};
/* 1.2V LDO */
struct regulator_consumer_supply tps65070_ldo2_consumers[] = {
static struct regulator_consumer_supply tps65070_ldo2_consumers[] = {
{
.supply = "sata_vdd",
},
......@@ -475,7 +508,7 @@ static struct tps6507x_reg_platform_data tps6507x_platform_data = {
.defdcdc_default = true,
};
struct regulator_init_data tps65070_regulator_data[] = {
static struct regulator_init_data tps65070_regulator_data[] = {
/* dcdc1 */
{
.constraints = {
......@@ -576,6 +609,23 @@ static const short da850_evm_lcdc_pins[] = {
-1
};
static const short da850_evm_mii_pins[] = {
DA850_MII_TXEN, DA850_MII_TXCLK, DA850_MII_COL, DA850_MII_TXD_3,
DA850_MII_TXD_2, DA850_MII_TXD_1, DA850_MII_TXD_0, DA850_MII_RXER,
DA850_MII_CRS, DA850_MII_RXCLK, DA850_MII_RXDV, DA850_MII_RXD_3,
DA850_MII_RXD_2, DA850_MII_RXD_1, DA850_MII_RXD_0, DA850_MDIO_CLK,
DA850_MDIO_D,
-1
};
static const short da850_evm_rmii_pins[] = {
DA850_RMII_TXD_0, DA850_RMII_TXD_1, DA850_RMII_TXEN,
DA850_RMII_CRS_DV, DA850_RMII_RXD_0, DA850_RMII_RXD_1,
DA850_RMII_RXER, DA850_RMII_MHZ_50_CLK, DA850_MDIO_CLK,
DA850_MDIO_D,
-1
};
static int __init da850_evm_config_emac(void)
{
void __iomem *cfg_chip3_base;
......@@ -593,12 +643,12 @@ static int __init da850_evm_config_emac(void)
if (rmii_en) {
val |= BIT(8);
ret = davinci_cfg_reg_list(da850_rmii_pins);
ret = davinci_cfg_reg_list(da850_evm_rmii_pins);
pr_info("EMAC: RMII PHY configured, MII PHY will not be"
" functional\n");
} else {
val &= ~BIT(8);
ret = davinci_cfg_reg_list(da850_cpgmac_pins);
ret = davinci_cfg_reg_list(da850_evm_mii_pins);
pr_info("EMAC: MII PHY configured, RMII PHY will not be"
" functional\n");
}
......@@ -625,8 +675,7 @@ static int __init da850_evm_config_emac(void)
/* Enable/Disable MII MDIO clock */
gpio_direction_output(DA850_MII_MDIO_CLKEN_PIN, rmii_en);
soc_info->emac_pdata->phy_mask = DA850_EVM_PHY_MASK;
soc_info->emac_pdata->mdio_max_freq = DA850_EVM_MDIO_FREQUENCY;
soc_info->emac_pdata->phy_id = DA850_EVM_PHY_ID;
ret = da8xx_register_emac();
if (ret)
......@@ -787,7 +836,7 @@ static __init void da850_evm_init(void)
if (ret)
pr_warning("da850_evm_init: rtc setup failed: %d\n", ret);
ret = da850_register_cpufreq();
ret = da850_register_cpufreq("pll0_sysclk3");
if (ret)
pr_warning("da850_evm_init: cpufreq registration failed: %d\n",
ret);
......@@ -806,6 +855,9 @@ static __init void da850_evm_init(void)
#ifdef CONFIG_SERIAL_8250_CONSOLE
static int __init da850_evm_console_init(void)
{
if (!machine_is_davinci_da850_evm())
return 0;
return add_preferred_console("ttyS", 2, "115200");
}
console_initcall(da850_evm_console_init);
......@@ -816,7 +868,7 @@ static void __init da850_evm_map_io(void)
da850_init();
}
MACHINE_START(DAVINCI_DA850_EVM, "DaVinci DA850/OMAP-L138 EVM")
MACHINE_START(DAVINCI_DA850_EVM, "DaVinci DA850/OMAP-L138/AM18x EVM")
.boot_params = (DA8XX_DDR_BASE + 0x100),
.map_io = da850_evm_map_io,
.init_irq = cp_intc_init,
......
arch/arm/mach-davinci/board-dm365-evm.c
浏览文件 @ 7940a34b
......@@ -54,9 +54,7 @@ static inline int have_tvp7002(void)
return 0;
}
#define DM365_EVM_PHY_MASK (0x2)
#define DM365_EVM_MDIO_FREQUENCY (2200000) /* PHY bus frequency */
#define DM365_EVM_PHY_ID "0:01"
/*
* A MAX-II CPLD is used for various board control functions.
*/
......@@ -175,7 +173,9 @@ static struct at24_platform_data eeprom_info = {
.context = (void *)0x7f00,
};
static struct snd_platform_data dm365_evm_snd_data;
static struct snd_platform_data dm365_evm_snd_data = {
.asp_chan_q = EVENTQ_3,
};
static struct i2c_board_info i2c_info[] = {
{
......@@ -533,8 +533,7 @@ static void __init evm_init_cpld(void)
/* ... and ENET ... */
dm365evm_emac_configure();
soc_info->emac_pdata->phy_mask = DM365_EVM_PHY_MASK;
soc_info->emac_pdata->mdio_max_freq = DM365_EVM_MDIO_FREQUENCY;
soc_info->emac_pdata->phy_id = DM365_EVM_PHY_ID;
resets &= ~BIT(3);
/* ... and AIC33 */
......
arch/arm/mach-davinci/board-dm644x-evm.c
浏览文件 @ 7940a34b
......@@ -37,10 +37,9 @@
#include <mach/nand.h>
#include <mach/mmc.h>
#include <mach/usb.h>
#include <mach/aemif.h>
#define DM644X_EVM_PHY_MASK (0x2)
#define DM644X_EVM_MDIO_FREQUENCY (2200000) /* PHY bus frequency */
#define DM644X_EVM_PHY_ID "0:01"
#define LXT971_PHY_ID (0x001378e2)
#define LXT971_PHY_MASK (0xfffffff0)
......@@ -137,11 +136,22 @@ static struct mtd_partition davinci_evm_nandflash_partition[] = {
*/
};
static struct davinci_aemif_timing davinci_evm_nandflash_timing = {
.wsetup = 20,
.wstrobe = 40,
.whold = 20,
.rsetup = 10,
.rstrobe = 40,
.rhold = 10,
.ta = 40,
};
static struct davinci_nand_pdata davinci_evm_nandflash_data = {
.parts = davinci_evm_nandflash_partition,
.nr_parts = ARRAY_SIZE(davinci_evm_nandflash_partition),
.ecc_mode = NAND_ECC_HW,
.options = NAND_USE_FLASH_BBT,
.timing = &davinci_evm_nandflash_timing,
};
static struct resource davinci_evm_nandflash_resource[] = {
......@@ -695,9 +705,7 @@ static __init void davinci_evm_init(void)
davinci_serial_init(&uart_config);
dm644x_init_asp(&dm644x_evm_snd_data);
soc_info->emac_pdata->phy_mask = DM644X_EVM_PHY_MASK;
soc_info->emac_pdata->mdio_max_freq = DM644X_EVM_MDIO_FREQUENCY;
soc_info->emac_pdata->phy_id = DM644X_EVM_PHY_ID;
/* Register the fixup for PHY on DaVinci */
phy_register_fixup_for_uid(LXT971_PHY_ID, LXT971_PHY_MASK,
davinci_phy_fixup);
......
arch/arm/mach-davinci/board-dm646x-evm.c
浏览文件 @ 7940a34b
......@@ -42,6 +42,7 @@
#include <mach/nand.h>
#include <mach/clock.h>
#include <mach/cdce949.h>
#include <mach/aemif.h>
#include "clock.h"
......@@ -71,6 +72,16 @@ static struct mtd_partition davinci_nand_partitions[] = {
}
};
static struct davinci_aemif_timing dm6467tevm_nandflash_timing = {
.wsetup = 29,
.wstrobe = 24,
.whold = 14,
.rsetup = 19,
.rstrobe = 33,
.rhold = 0,
.ta = 29,
};
static struct davinci_nand_pdata davinci_nand_data = {
.mask_cle = 0x80000,
.mask_ale = 0x40000,
......@@ -718,9 +729,7 @@ static struct davinci_uart_config uart_config __initdata = {
.enabled_uarts = (1 << 0),
};
#define DM646X_EVM_PHY_MASK (0x2)
#define DM646X_EVM_MDIO_FREQUENCY (2200000) /* PHY bus frequency */
#define DM646X_EVM_PHY_ID "0:01"
/*
* The following EDMA channels/slots are not being used by drivers (for
* example: Timer, GPIO, UART events etc) on dm646x, hence they are being
......@@ -763,6 +772,9 @@ static __init void evm_init(void)
dm646x_init_mcasp0(&dm646x_evm_snd_data[0]);
dm646x_init_mcasp1(&dm646x_evm_snd_data[1]);
if (machine_is_davinci_dm6467tevm())
davinci_nand_data.timing = &dm6467tevm_nandflash_timing;
platform_device_register(&davinci_nand_device);
dm646x_init_edma(dm646x_edma_rsv);
......@@ -770,8 +782,7 @@ static __init void evm_init(void)
if (HAS_ATA)
davinci_init_ide();
soc_info->emac_pdata->phy_mask = DM646X_EVM_PHY_MASK;
soc_info->emac_pdata->mdio_max_freq = DM646X_EVM_MDIO_FREQUENCY;
soc_info->emac_pdata->phy_id = DM646X_EVM_PHY_ID;
}
#define DM646X_EVM_REF_FREQ 27000000
......
arch/arm/mach-davinci/board-mityomapl138.c 0 → 100644
浏览文件 @ 7940a34b
/*
* Critical Link MityOMAP-L138 SoM
*
* Copyright (C) 2010 Critical Link LLC - http://www.criticallink.com
*
* This file is licensed under the terms of the GNU General Public License
* version 2. This program is licensed "as is" without any warranty of
* any kind, whether express or implied.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/console.h>
#include <linux/platform_device.h>
#include <linux/mtd/partitions.h>
#include <linux/regulator/machine.h>
#include <linux/i2c.h>
#include <linux/i2c/at24.h>
#include <linux/etherdevice.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <mach/common.h>
#include <mach/cp_intc.h>
#include <mach/da8xx.h>
#include <mach/nand.h>
#include <mach/mux.h>
#define MITYOMAPL138_PHY_ID "0:03"
#define FACTORY_CONFIG_MAGIC 0x012C0138
#define FACTORY_CONFIG_VERSION 0x00010001
/* Data Held in On-Board I2C device */
struct factory_config {
u32 magic;
u32 version;
u8 mac[6];
u32 fpga_type;
u32 spare;
u32 serialnumber;
char partnum[32];
};
static struct factory_config factory_config;
static void read_factory_config(struct memory_accessor *a, void *context)
{
int ret;
struct davinci_soc_info *soc_info = &davinci_soc_info;
ret = a->read(a, (char *)&factory_config, 0, sizeof(factory_config));
if (ret != sizeof(struct factory_config)) {
pr_warning("MityOMAPL138: Read Factory Config Failed: %d\n",
ret);
return;
}
if (factory_config.magic != FACTORY_CONFIG_MAGIC) {
pr_warning("MityOMAPL138: Factory Config Magic Wrong (%X)\n",
factory_config.magic);
return;
}
if (factory_config.version != FACTORY_CONFIG_VERSION) {
pr_warning("MityOMAPL138: Factory Config Version Wrong (%X)\n",
factory_config.version);
return;
}
pr_info("MityOMAPL138: Found MAC = %pM\n", factory_config.mac);
pr_info("MityOMAPL138: Part Number = %s\n", factory_config.partnum);
if (is_valid_ether_addr(factory_config.mac))
memcpy(soc_info->emac_pdata->mac_addr,
factory_config.mac, ETH_ALEN);
else
pr_warning("MityOMAPL138: Invalid MAC found "
"in factory config block\n");
}
static struct at24_platform_data mityomapl138_fd_chip = {
.byte_len = 256,
.page_size = 8,
.flags = AT24_FLAG_READONLY | AT24_FLAG_IRUGO,
.setup = read_factory_config,
.context = NULL,
};
static struct davinci_i2c_platform_data mityomap_i2c_0_pdata = {
.bus_freq = 100, /* kHz */
.bus_delay = 0, /* usec */
};
/* TPS65023 voltage regulator support */
/* 1.2V Core */
static struct regulator_consumer_supply tps65023_dcdc1_consumers[] = {
{
.supply = "cvdd",
},
};
/* 1.8V */
static struct regulator_consumer_supply tps65023_dcdc2_consumers[] = {
{
.supply = "usb0_vdda18",
},
{
.supply = "usb1_vdda18",
},
{
.supply = "ddr_dvdd18",
},
{
.supply = "sata_vddr",
},
};
/* 1.2V */
static struct regulator_consumer_supply tps65023_dcdc3_consumers[] = {
{
.supply = "sata_vdd",
},
{
.supply = "usb_cvdd",
},
{
.supply = "pll0_vdda",
},
{
.supply = "pll1_vdda",
},
};
/* 1.8V Aux LDO, not used */
static struct regulator_consumer_supply tps65023_ldo1_consumers[] = {
{
.supply = "1.8v_aux",
},
};
/* FPGA VCC Aux (2.5 or 3.3) LDO */
static struct regulator_consumer_supply tps65023_ldo2_consumers[] = {
{
.supply = "vccaux",
},
};
static struct regulator_init_data tps65023_regulator_data[] = {
/* dcdc1 */
{
.constraints = {
.min_uV = 1150000,
.max_uV = 1350000,
.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
REGULATOR_CHANGE_STATUS,
.boot_on = 1,
},
.num_consumer_supplies = ARRAY_SIZE(tps65023_dcdc1_consumers),
.consumer_supplies = tps65023_dcdc1_consumers,
},
/* dcdc2 */
{
.constraints = {
.min_uV = 1800000,
.max_uV = 1800000,
.valid_ops_mask = REGULATOR_CHANGE_STATUS,
.boot_on = 1,
},
.num_consumer_supplies = ARRAY_SIZE(tps65023_dcdc2_consumers),
.consumer_supplies = tps65023_dcdc2_consumers,
},
/* dcdc3 */
{
.constraints = {
.min_uV = 1200000,
.max_uV = 1200000,
.valid_ops_mask = REGULATOR_CHANGE_STATUS,
.boot_on = 1,
},
.num_consumer_supplies = ARRAY_SIZE(tps65023_dcdc3_consumers),
.consumer_supplies = tps65023_dcdc3_consumers,
},
/* ldo1 */
{
.constraints = {
.min_uV = 1800000,
.max_uV = 1800000,
.valid_ops_mask = REGULATOR_CHANGE_STATUS,
.boot_on = 1,
},
.num_consumer_supplies = ARRAY_SIZE(tps65023_ldo1_consumers),
.consumer_supplies = tps65023_ldo1_consumers,
},
/* ldo2 */
{
.constraints = {
.min_uV = 2500000,
.max_uV = 3300000,
.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
REGULATOR_CHANGE_STATUS,
.boot_on = 1,
},
.num_consumer_supplies = ARRAY_SIZE(tps65023_ldo2_consumers),
.consumer_supplies = tps65023_ldo2_consumers,
},
};
static struct i2c_board_info __initdata mityomap_tps65023_info[] = {
{
I2C_BOARD_INFO("tps65023", 0x48),
.platform_data = &tps65023_regulator_data[0],
},
{
I2C_BOARD_INFO("24c02", 0x50),
.platform_data = &mityomapl138_fd_chip,
},
};
static int __init pmic_tps65023_init(void)
{
return i2c_register_board_info(1, mityomap_tps65023_info,
ARRAY_SIZE(mityomap_tps65023_info));
}
/*
* MityDSP-L138 includes a 256 MByte large-page NAND flash
* (128K blocks).
*/
static struct mtd_partition mityomapl138_nandflash_partition[] = {
{
.name = "rootfs",
.offset = 0,
.size = SZ_128M,
.mask_flags = 0, /* MTD_WRITEABLE, */
},
{
.name = "homefs",
.offset = MTDPART_OFS_APPEND,
.size = MTDPART_SIZ_FULL,
.mask_flags = 0,
},
};
static struct davinci_nand_pdata mityomapl138_nandflash_data = {
.parts = mityomapl138_nandflash_partition,
.nr_parts = ARRAY_SIZE(mityomapl138_nandflash_partition),
.ecc_mode = NAND_ECC_HW,
.options = NAND_USE_FLASH_BBT | NAND_BUSWIDTH_16,
.ecc_bits = 1, /* 4 bit mode is not supported with 16 bit NAND */
};
static struct resource mityomapl138_nandflash_resource[] = {
{
.start = DA8XX_AEMIF_CS3_BASE,
.end = DA8XX_AEMIF_CS3_BASE + SZ_512K + 2 * SZ_1K - 1,
.flags = IORESOURCE_MEM,
},
{
.start = DA8XX_AEMIF_CTL_BASE,
.end = DA8XX_AEMIF_CTL_BASE + SZ_32K - 1,
.flags = IORESOURCE_MEM,
},
};
static struct platform_device mityomapl138_nandflash_device = {
.name = "davinci_nand",
.id = 0,
.dev = {
.platform_data = &mityomapl138_nandflash_data,
},
.num_resources = ARRAY_SIZE(mityomapl138_nandflash_resource),
.resource = mityomapl138_nandflash_resource,
};
static struct platform_device *mityomapl138_devices[] __initdata = {
&mityomapl138_nandflash_device,
};
static void __init mityomapl138_setup_nand(void)
{
platform_add_devices(mityomapl138_devices,
ARRAY_SIZE(mityomapl138_devices));
}
static struct davinci_uart_config mityomapl138_uart_config __initdata = {
.enabled_uarts = 0x7,
};
static const short mityomap_mii_pins[] = {
DA850_MII_TXEN, DA850_MII_TXCLK, DA850_MII_COL, DA850_MII_TXD_3,
DA850_MII_TXD_2, DA850_MII_TXD_1, DA850_MII_TXD_0, DA850_MII_RXER,
DA850_MII_CRS, DA850_MII_RXCLK, DA850_MII_RXDV, DA850_MII_RXD_3,
DA850_MII_RXD_2, DA850_MII_RXD_1, DA850_MII_RXD_0, DA850_MDIO_CLK,
DA850_MDIO_D,
-1
};
static const short mityomap_rmii_pins[] = {
DA850_RMII_TXD_0, DA850_RMII_TXD_1, DA850_RMII_TXEN,
DA850_RMII_CRS_DV, DA850_RMII_RXD_0, DA850_RMII_RXD_1,
DA850_RMII_RXER, DA850_RMII_MHZ_50_CLK, DA850_MDIO_CLK,
DA850_MDIO_D,
-1
};
static void __init mityomapl138_config_emac(void)
{
void __iomem *cfg_chip3_base;
int ret;
u32 val;
struct davinci_soc_info *soc_info = &davinci_soc_info;
soc_info->emac_pdata->rmii_en = 0; /* hardcoded for now */
cfg_chip3_base = DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP3_REG);
val = __raw_readl(cfg_chip3_base);
if (soc_info->emac_pdata->rmii_en) {
val |= BIT(8);
ret = davinci_cfg_reg_list(mityomap_rmii_pins);
pr_info("RMII PHY configured\n");
} else {
val &= ~BIT(8);
ret = davinci_cfg_reg_list(mityomap_mii_pins);
pr_info("MII PHY configured\n");
}
if (ret) {
pr_warning("mii/rmii mux setup failed: %d\n", ret);
return;
}
/* configure the CFGCHIP3 register for RMII or MII */
__raw_writel(val, cfg_chip3_base);
soc_info->emac_pdata->phy_id = MITYOMAPL138_PHY_ID;
ret = da8xx_register_emac();
if (ret)
pr_warning("emac registration failed: %d\n", ret);
}
static struct davinci_pm_config da850_pm_pdata = {
.sleepcount = 128,
};
static struct platform_device da850_pm_device = {
.name = "pm-davinci",
.dev = {
.platform_data = &da850_pm_pdata,
},
.id = -1,
};
static void __init mityomapl138_init(void)
{
int ret;
/* for now, no special EDMA channels are reserved */
ret = da850_register_edma(NULL);
if (ret)
pr_warning("edma registration failed: %d\n", ret);
ret = da8xx_register_watchdog();
if (ret)
pr_warning("watchdog registration failed: %d\n", ret);
davinci_serial_init(&mityomapl138_uart_config);
ret = da8xx_register_i2c(0, &mityomap_i2c_0_pdata);
if (ret)
pr_warning("i2c0 registration failed: %d\n", ret);
ret = pmic_tps65023_init();
if (ret)
pr_warning("TPS65023 PMIC init failed: %d\n", ret);
mityomapl138_setup_nand();
mityomapl138_config_emac();
ret = da8xx_register_rtc();
if (ret)
pr_warning("rtc setup failed: %d\n", ret);
ret = da850_register_cpufreq("pll0_sysclk3");
if (ret)
pr_warning("cpufreq registration failed: %d\n", ret);
ret = da8xx_register_cpuidle();
if (ret)
pr_warning("cpuidle registration failed: %d\n", ret);
ret = da850_register_pm(&da850_pm_device);
if (ret)
pr_warning("da850_evm_init: suspend registration failed: %d\n",
ret);
}
#ifdef CONFIG_SERIAL_8250_CONSOLE
static int __init mityomapl138_console_init(void)
{
if (!machine_is_mityomapl138())
return 0;
return add_preferred_console("ttyS", 1, "115200");
}
console_initcall(mityomapl138_console_init);
#endif
static void __init mityomapl138_map_io(void)
{
da850_init();
}
MACHINE_START(MITYOMAPL138, "MityDSP-L138/MityARM-1808")
.phys_io = IO_PHYS,
.io_pg_offst = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc,
.boot_params = (DA8XX_DDR_BASE + 0x100),
.map_io = mityomapl138_map_io,
.init_irq = cp_intc_init,
.timer = &davinci_timer,
.init_machine = mityomapl138_init,
MACHINE_END
arch/arm/mach-davinci/board-neuros-osd2.c
浏览文件 @ 7940a34b
......@@ -39,9 +39,7 @@
#include <mach/mmc.h>
#include <mach/usb.h>
#define NEUROS_OSD2_PHY_MASK 0x2
#define NEUROS_OSD2_MDIO_FREQUENCY 2200000 /* PHY bus frequency */
#define NEUROS_OSD2_PHY_ID "0:01"
#define LXT971_PHY_ID 0x001378e2
#define LXT971_PHY_MASK 0xfffffff0
......@@ -252,8 +250,7 @@ static __init void davinci_ntosd2_init(void)
davinci_serial_init(&uart_config);
dm644x_init_asp(&dm644x_ntosd2_snd_data);
soc_info->emac_pdata->phy_mask = NEUROS_OSD2_PHY_MASK;
soc_info->emac_pdata->mdio_max_freq = NEUROS_OSD2_MDIO_FREQUENCY;
soc_info->emac_pdata->phy_id = NEUROS_OSD2_PHY_ID;
davinci_setup_usb(1000, 8);
/*
......
arch/arm/mach-davinci/board-omapl138-hawk.c 0 → 100644
浏览文件 @ 7940a34b
/*
* Hawkboard.org based on TI's OMAP-L138 Platform
*
* Initial code: Syed Mohammed Khasim
*
* Copyright (C) 2009 Texas Instruments Incorporated - http://www.ti.com
*
* This file is licensed under the terms of the GNU General Public License
* version 2. This program is licensed "as is" without any warranty of
* any kind, whether express or implied.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/console.h>
#include <linux/gpio.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <mach/cp_intc.h>
#include <mach/da8xx.h>
static struct davinci_uart_config omapl138_hawk_uart_config __initdata = {
.enabled_uarts = 0x7,
};
static __init void omapl138_hawk_init(void)
{
int ret;
davinci_serial_init(&omapl138_hawk_uart_config);
ret = da8xx_register_watchdog();
if (ret)
pr_warning("omapl138_hawk_init: "
"watchdog registration failed: %d\n",
ret);
}
#ifdef CONFIG_SERIAL_8250_CONSOLE
static int __init omapl138_hawk_console_init(void)
{
if (!machine_is_omapl138_hawkboard())
return 0;
return add_preferred_console("ttyS", 2, "115200");
}
console_initcall(omapl138_hawk_console_init);
#endif
static void __init omapl138_hawk_map_io(void)
{
da850_init();
}
MACHINE_START(OMAPL138_HAWKBOARD, "AM18x/OMAP-L138 Hawkboard")
.phys_io = IO_PHYS,
.io_pg_offst = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc,
.boot_params = (DA8XX_DDR_BASE + 0x100),
.map_io = omapl138_hawk_map_io,
.init_irq = cp_intc_init,
.timer = &davinci_timer,
.init_machine = omapl138_hawk_init,
MACHINE_END
arch/arm/mach-davinci/board-sffsdr.c
浏览文件 @ 7940a34b
......@@ -42,9 +42,7 @@
#include <mach/mux.h>
#include <mach/usb.h>
#define SFFSDR_PHY_MASK (0x2)
#define SFFSDR_MDIO_FREQUENCY (2200000) /* PHY bus frequency */
#define SFFSDR_PHY_ID "0:01"
static struct mtd_partition davinci_sffsdr_nandflash_partition[] = {
/* U-Boot Environment: Block 0
* UBL: Block 1
......@@ -143,8 +141,7 @@ static __init void davinci_sffsdr_init(void)
ARRAY_SIZE(davinci_sffsdr_devices));
sffsdr_init_i2c();
davinci_serial_init(&uart_config);
soc_info->emac_pdata->phy_mask = SFFSDR_PHY_MASK;
soc_info->emac_pdata->mdio_max_freq = SFFSDR_MDIO_FREQUENCY;
soc_info->emac_pdata->phy_id = SFFSDR_PHY_ID;
davinci_setup_usb(0, 0); /* We support only peripheral mode. */
/* mux VLYNQ pins */
......
arch/arm/mach-davinci/board-tnetv107x-evm.c
浏览文件 @ 7940a34b
......@@ -23,6 +23,9 @@
#include <linux/ratelimit.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/input.h>
#include <linux/input/matrix_keypad.h>
#include <asm/mach/arch.h>
#include <asm/mach-types.h>
......@@ -141,10 +144,63 @@ static struct davinci_uart_config serial_config __initconst = {
.enabled_uarts = BIT(1),
};
static const uint32_t keymap[] = {
KEY(0, 0, KEY_NUMERIC_1),
KEY(0, 1, KEY_NUMERIC_2),
KEY(0, 2, KEY_NUMERIC_3),
KEY(0, 3, KEY_FN_F1),
KEY(0, 4, KEY_MENU),
KEY(1, 0, KEY_NUMERIC_4),
KEY(1, 1, KEY_NUMERIC_5),
KEY(1, 2, KEY_NUMERIC_6),
KEY(1, 3, KEY_UP),
KEY(1, 4, KEY_FN_F2),
KEY(2, 0, KEY_NUMERIC_7),
KEY(2, 1, KEY_NUMERIC_8),
KEY(2, 2, KEY_NUMERIC_9),
KEY(2, 3, KEY_LEFT),
KEY(2, 4, KEY_ENTER),
KEY(3, 0, KEY_NUMERIC_STAR),
KEY(3, 1, KEY_NUMERIC_0),
KEY(3, 2, KEY_NUMERIC_POUND),
KEY(3, 3, KEY_DOWN),
KEY(3, 4, KEY_RIGHT),
KEY(4, 0, KEY_FN_F3),
KEY(4, 1, KEY_FN_F4),
KEY(4, 2, KEY_MUTE),
KEY(4, 3, KEY_HOME),
KEY(4, 4, KEY_BACK),
KEY(5, 0, KEY_VOLUMEDOWN),
KEY(5, 1, KEY_VOLUMEUP),
KEY(5, 2, KEY_F1),
KEY(5, 3, KEY_F2),
KEY(5, 4, KEY_F3),
};
static const struct matrix_keymap_data keymap_data = {
.keymap = keymap,
.keymap_size = ARRAY_SIZE(keymap),
};
static struct matrix_keypad_platform_data keypad_config = {
.keymap_data = &keymap_data,
.num_row_gpios = 6,
.num_col_gpios = 5,
.debounce_ms = 0, /* minimum */
.active_low = 0, /* pull up realization */
.no_autorepeat = 0,
};
static struct tnetv107x_device_info evm_device_info __initconst = {
.serial_config = &serial_config,
.mmc_config[1] = &mmc_config, /* controller 1 */
.nand_config[0] = &nand_config, /* chip select 0 */
.keypad_config = &keypad_config,
};
static __init void tnetv107x_evm_board_init(void)
......
arch/arm/mach-davinci/clock.c
浏览文件 @ 7940a34b
......@@ -236,7 +236,7 @@ static int __init clk_disable_unused(void)
if (!davinci_psc_is_clk_active(ck->gpsc, ck->lpsc))
continue;
pr_info("Clocks: disable unused %s\n", ck->name);
pr_debug("Clocks: disable unused %s\n", ck->name);
davinci_psc_config(psc_domain(ck), ck->gpsc, ck->lpsc,
(ck->flags & PSC_SWRSTDISABLE) ?
......@@ -287,6 +287,79 @@ static unsigned long clk_sysclk_recalc(struct clk *clk)
return rate;
}
int davinci_set_sysclk_rate(struct clk *clk, unsigned long rate)
{
unsigned v;
struct pll_data *pll;
unsigned long input;
unsigned ratio = 0;
/* If this is the PLL base clock, wrong function to call */
if (clk->pll_data)
return -EINVAL;
/* There must be a parent... */
if (WARN_ON(!clk->parent))
return -EINVAL;
/* ... the parent must be a PLL... */
if (WARN_ON(!clk->parent->pll_data))
return -EINVAL;
/* ... and this clock must have a divider. */
if (WARN_ON(!clk->div_reg))
return -EINVAL;
pll = clk->parent->pll_data;
input = clk->parent->rate;
/* If pre-PLL, source clock is before the multiplier and divider(s) */
if (clk->flags & PRE_PLL)
input = pll->input_rate;
if (input > rate) {
/*
* Can afford to provide an output little higher than requested
* only if maximum rate supported by hardware on this sysclk
* is known.
*/
if (clk->maxrate) {
ratio = DIV_ROUND_CLOSEST(input, rate);
if (input / ratio > clk->maxrate)
ratio = 0;
}
if (ratio == 0)
ratio = DIV_ROUND_UP(input, rate);
ratio--;
}
if (ratio > PLLDIV_RATIO_MASK)
return -EINVAL;
do {
v = __raw_readl(pll->base + PLLSTAT);
} while (v & PLLSTAT_GOSTAT);
v = __raw_readl(pll->base + clk->div_reg);
v &= ~PLLDIV_RATIO_MASK;
v |= ratio | PLLDIV_EN;
__raw_writel(v, pll->base + clk->div_reg);
v = __raw_readl(pll->base + PLLCMD);
v |= PLLCMD_GOSET;
__raw_writel(v, pll->base + PLLCMD);
do {
v = __raw_readl(pll->base + PLLSTAT);
} while (v & PLLSTAT_GOSTAT);
return 0;
}
EXPORT_SYMBOL(davinci_set_sysclk_rate);
static unsigned long clk_leafclk_recalc(struct clk *clk)
{
if (WARN_ON(!clk->parent))
......
arch/arm/mach-davinci/clock.h
浏览文件 @ 7940a34b
......@@ -70,6 +70,9 @@
#include <linux/list.h>
#include <asm/clkdev.h>
#define PLLSTAT_GOSTAT BIT(0)
#define PLLCMD_GOSET BIT(0)
struct pll_data {
u32 phys_base;
void __iomem *base;
......@@ -86,6 +89,7 @@ struct clk {
struct module *owner;
const char *name;
unsigned long rate;
unsigned long maxrate; /* H/W supported max rate */
u8 usecount;
u8 lpsc;
u8 gpsc;
......@@ -118,6 +122,7 @@ struct clk {
int davinci_clk_init(struct clk_lookup *clocks);
int davinci_set_pllrate(struct pll_data *pll, unsigned int prediv,
unsigned int mult, unsigned int postdiv);
int davinci_set_sysclk_rate(struct clk *clk, unsigned long rate);
extern struct platform_device davinci_wdt_device;
extern void davinci_watchdog_reset(struct platform_device *);
......
arch/arm/mach-davinci/cpufreq.c
浏览文件 @ 7940a34b
......@@ -34,6 +34,8 @@
struct davinci_cpufreq {
struct device *dev;
struct clk *armclk;
struct clk *asyncclk;
unsigned long asyncrate;
};
static struct davinci_cpufreq cpufreq;
......@@ -104,15 +106,27 @@ static int davinci_target(struct cpufreq_policy *policy,
cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE);
/* if moving to higher frequency, up the voltage beforehand */
if (pdata->set_voltage && freqs.new > freqs.old)
pdata->set_voltage(idx);
if (pdata->set_voltage && freqs.new > freqs.old) {
ret = pdata->set_voltage(idx);
if (ret)
goto out;
}
ret = clk_set_rate(armclk, idx);
if (ret)
goto out;
if (cpufreq.asyncclk) {
ret = clk_set_rate(cpufreq.asyncclk, cpufreq.asyncrate);
if (ret)
goto out;
}
/* if moving to lower freq, lower the voltage after lowering freq */
if (pdata->set_voltage && freqs.new < freqs.old)
pdata->set_voltage(idx);
out:
cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE);
return ret;
......@@ -185,6 +199,7 @@ static struct cpufreq_driver davinci_driver = {
static int __init davinci_cpufreq_probe(struct platform_device *pdev)
{
struct davinci_cpufreq_config *pdata = pdev->dev.platform_data;
struct clk *asyncclk;
if (!pdata)
return -EINVAL;
......@@ -199,6 +214,12 @@ static int __init davinci_cpufreq_probe(struct platform_device *pdev)
return PTR_ERR(cpufreq.armclk);
}
asyncclk = clk_get(cpufreq.dev, "async");
if (!IS_ERR(asyncclk)) {
cpufreq.asyncclk = asyncclk;
cpufreq.asyncrate = clk_get_rate(asyncclk);
}
return cpufreq_register_driver(&davinci_driver);
}
......@@ -206,6 +227,9 @@ static int __exit davinci_cpufreq_remove(struct platform_device *pdev)
{
clk_put(cpufreq.armclk);
if (cpufreq.asyncclk)
clk_put(cpufreq.asyncclk);
return cpufreq_unregister_driver(&davinci_driver);
}
......
arch/arm/mach-davinci/da850.c
浏览文件 @ 7940a34b
......@@ -86,6 +86,8 @@ static struct clk pll0_sysclk3 = {
.parent = &pll0_clk,
.flags = CLK_PLL,
.div_reg = PLLDIV3,
.set_rate = davinci_set_sysclk_rate,
.maxrate = 100000000,
};
static struct clk pll0_sysclk4 = {
......@@ -323,12 +325,19 @@ static struct clk lcdc_clk = {
.gpsc = 1,
};
static struct clk mmcsd_clk = {
.name = "mmcsd",
static struct clk mmcsd0_clk = {
.name = "mmcsd0",
.parent = &pll0_sysclk2,
.lpsc = DA8XX_LPSC0_MMC_SD,
};
static struct clk mmcsd1_clk = {
.name = "mmcsd1",
.parent = &pll0_sysclk2,
.lpsc = DA850_LPSC1_MMC_SD1,
.gpsc = 1,
};
static struct clk aemif_clk = {
.name = "aemif",
.parent = &pll0_sysclk3,
......@@ -375,7 +384,8 @@ static struct clk_lookup da850_clks[] = {
CLK("davinci_emac.1", NULL, &emac_clk),
CLK("davinci-mcasp.0", NULL, &mcasp_clk),
CLK("da8xx_lcdc.0", NULL, &lcdc_clk),
CLK("davinci_mmc.0", NULL, &mmcsd_clk),
CLK("davinci_mmc.0", NULL, &mmcsd0_clk),
CLK("davinci_mmc.1", NULL, &mmcsd1_clk),
CLK(NULL, "aemif", &aemif_clk),
CLK(NULL, NULL, NULL),
};
......@@ -572,15 +582,9 @@ const short da850_cpgmac_pins[] __initdata = {
DA850_MII_TXD_2, DA850_MII_TXD_1, DA850_MII_TXD_0, DA850_MII_RXER,
DA850_MII_CRS, DA850_MII_RXCLK, DA850_MII_RXDV, DA850_MII_RXD_3,
DA850_MII_RXD_2, DA850_MII_RXD_1, DA850_MII_RXD_0, DA850_MDIO_CLK,
DA850_MDIO_D,
-1
};
const short da850_rmii_pins[] __initdata = {
DA850_RMII_TXD_0, DA850_RMII_TXD_1, DA850_RMII_TXEN,
DA850_RMII_CRS_DV, DA850_RMII_RXD_0, DA850_RMII_RXD_1,
DA850_RMII_RXER, DA850_RMII_MHZ_50_CLK, DA850_MDIO_CLK,
DA850_MDIO_D,
DA850_MDIO_D, DA850_RMII_TXD_0, DA850_RMII_TXD_1, DA850_RMII_TXEN,
DA850_RMII_CRS_DV, DA850_RMII_RXD_0, DA850_RMII_RXD_1, DA850_RMII_RXER,
DA850_RMII_MHZ_50_CLK,
-1
};
......@@ -607,27 +611,19 @@ const short da850_mmcsd0_pins[] __initdata = {
-1
};
const short da850_nand_pins[] __initdata = {
DA850_EMA_D_7, DA850_EMA_D_6, DA850_EMA_D_5, DA850_EMA_D_4,
DA850_EMA_D_3, DA850_EMA_D_2, DA850_EMA_D_1, DA850_EMA_D_0,
DA850_EMA_A_1, DA850_EMA_A_2, DA850_NEMA_CS_3, DA850_NEMA_CS_4,
DA850_NEMA_WE, DA850_NEMA_OE,
-1
};
const short da850_nor_pins[] __initdata = {
const short da850_emif25_pins[] __initdata = {
DA850_EMA_BA_1, DA850_EMA_CLK, DA850_EMA_WAIT_1, DA850_NEMA_CS_2,
DA850_NEMA_WE, DA850_NEMA_OE, DA850_EMA_D_0, DA850_EMA_D_1,
DA850_EMA_D_2, DA850_EMA_D_3, DA850_EMA_D_4, DA850_EMA_D_5,
DA850_EMA_D_6, DA850_EMA_D_7, DA850_EMA_D_8, DA850_EMA_D_9,
DA850_EMA_D_10, DA850_EMA_D_11, DA850_EMA_D_12, DA850_EMA_D_13,
DA850_EMA_D_14, DA850_EMA_D_15, DA850_EMA_A_0, DA850_EMA_A_1,
DA850_EMA_A_2, DA850_EMA_A_3, DA850_EMA_A_4, DA850_EMA_A_5,
DA850_EMA_A_6, DA850_EMA_A_7, DA850_EMA_A_8, DA850_EMA_A_9,
DA850_EMA_A_10, DA850_EMA_A_11, DA850_EMA_A_12, DA850_EMA_A_13,
DA850_EMA_A_14, DA850_EMA_A_15, DA850_EMA_A_16, DA850_EMA_A_17,
DA850_EMA_A_18, DA850_EMA_A_19, DA850_EMA_A_20, DA850_EMA_A_21,
DA850_EMA_A_22, DA850_EMA_A_23,
DA850_NEMA_CS_3, DA850_NEMA_CS_4, DA850_NEMA_WE, DA850_NEMA_OE,
DA850_EMA_D_0, DA850_EMA_D_1, DA850_EMA_D_2, DA850_EMA_D_3,
DA850_EMA_D_4, DA850_EMA_D_5, DA850_EMA_D_6, DA850_EMA_D_7,
DA850_EMA_D_8, DA850_EMA_D_9, DA850_EMA_D_10, DA850_EMA_D_11,
DA850_EMA_D_12, DA850_EMA_D_13, DA850_EMA_D_14, DA850_EMA_D_15,
DA850_EMA_A_0, DA850_EMA_A_1, DA850_EMA_A_2, DA850_EMA_A_3,
DA850_EMA_A_4, DA850_EMA_A_5, DA850_EMA_A_6, DA850_EMA_A_7,
DA850_EMA_A_8, DA850_EMA_A_9, DA850_EMA_A_10, DA850_EMA_A_11,
DA850_EMA_A_12, DA850_EMA_A_13, DA850_EMA_A_14, DA850_EMA_A_15,
DA850_EMA_A_16, DA850_EMA_A_17, DA850_EMA_A_18, DA850_EMA_A_19,
DA850_EMA_A_20, DA850_EMA_A_21, DA850_EMA_A_22, DA850_EMA_A_23,
-1
};
......@@ -851,7 +847,7 @@ static const struct da850_opp da850_opp_300 = {
.prediv = 1,
.mult = 25,
.postdiv = 2,
.cvdd_min = 1140000,
.cvdd_min = 1200000,
.cvdd_max = 1320000,
};
......@@ -860,7 +856,7 @@ static const struct da850_opp da850_opp_200 = {
.prediv = 1,
.mult = 25,
.postdiv = 3,
.cvdd_min = 1050000,
.cvdd_min = 1100000,
.cvdd_max = 1160000,
};
......@@ -869,7 +865,7 @@ static const struct da850_opp da850_opp_96 = {
.prediv = 1,
.mult = 20,
.postdiv = 5,
.cvdd_min = 950000,
.cvdd_min = 1000000,
.cvdd_max = 1050000,
};
......@@ -929,10 +925,16 @@ static struct platform_device da850_cpufreq_device = {
.dev = {
.platform_data = &cpufreq_info,
},
.id = -1,
};
int __init da850_register_cpufreq(void)
int __init da850_register_cpufreq(char *async_clk)
{
/* cpufreq driver can help keep an "async" clock constant */
if (async_clk)
clk_add_alias("async", da850_cpufreq_device.name,
async_clk, NULL);
return platform_device_register(&da850_cpufreq_device);
}
......@@ -983,7 +985,7 @@ static int da850_set_pll0rate(struct clk *clk, unsigned long index)
return 0;
}
#else
int __init da850_register_cpufreq(void)
int __init da850_register_cpufreq(char *async_clk)
{
return 0;
}
......
arch/arm/mach-davinci/devices-da8xx.c
浏览文件 @ 7940a34b
......@@ -24,6 +24,7 @@
#include "clock.h"
#define DA8XX_TPCC_BASE 0x01c00000
#define DA850_MMCSD1_BASE 0x01e1b000
#define DA850_TPCC1_BASE 0x01e30000
#define DA8XX_TPTC0_BASE 0x01c08000
#define DA8XX_TPTC1_BASE 0x01c08400
......@@ -41,7 +42,6 @@
#define DA8XX_EMAC_CTRL_REG_OFFSET 0x3000
#define DA8XX_EMAC_MOD_REG_OFFSET 0x2000
#define DA8XX_EMAC_RAM_OFFSET 0x0000
#define DA8XX_MDIO_REG_OFFSET 0x4000
#define DA8XX_EMAC_CTRL_RAM_SIZE SZ_8K
void __iomem *da8xx_syscfg0_base;
......@@ -351,7 +351,7 @@ int __init da8xx_register_watchdog(void)
static struct resource da8xx_emac_resources[] = {
{
.start = DA8XX_EMAC_CPPI_PORT_BASE,
.end = DA8XX_EMAC_CPPI_PORT_BASE + 0x5000 - 1,
.end = DA8XX_EMAC_CPPI_PORT_BASE + SZ_16K - 1,
.flags = IORESOURCE_MEM,
},
{
......@@ -380,7 +380,6 @@ struct emac_platform_data da8xx_emac_pdata = {
.ctrl_reg_offset = DA8XX_EMAC_CTRL_REG_OFFSET,
.ctrl_mod_reg_offset = DA8XX_EMAC_MOD_REG_OFFSET,
.ctrl_ram_offset = DA8XX_EMAC_RAM_OFFSET,
.mdio_reg_offset = DA8XX_MDIO_REG_OFFSET,
.ctrl_ram_size = DA8XX_EMAC_CTRL_RAM_SIZE,
.version = EMAC_VERSION_2,
};
......@@ -395,9 +394,34 @@ static struct platform_device da8xx_emac_device = {
.resource = da8xx_emac_resources,
};
static struct resource da8xx_mdio_resources[] = {
{
.start = DA8XX_EMAC_MDIO_BASE,
.end = DA8XX_EMAC_MDIO_BASE + SZ_4K - 1,
.flags = IORESOURCE_MEM,
},
};
static struct platform_device da8xx_mdio_device = {
.name = "davinci_mdio",
.id = 0,
.num_resources = ARRAY_SIZE(da8xx_mdio_resources),
.resource = da8xx_mdio_resources,
};
int __init da8xx_register_emac(void)
{
return platform_device_register(&da8xx_emac_device);
int ret;
ret = platform_device_register(&da8xx_mdio_device);
if (ret < 0)
return ret;
ret = platform_device_register(&da8xx_emac_device);
if (ret < 0)
return ret;
ret = clk_add_alias(NULL, dev_name(&da8xx_mdio_device.dev),
NULL, &da8xx_emac_device.dev);
return ret;
}
static struct resource da830_mcasp1_resources[] = {
......@@ -566,6 +590,44 @@ int __init da8xx_register_mmcsd0(struct davinci_mmc_config *config)
return platform_device_register(&da8xx_mmcsd0_device);
}
#ifdef CONFIG_ARCH_DAVINCI_DA850
static struct resource da850_mmcsd1_resources[] = {
{ /* registers */
.start = DA850_MMCSD1_BASE,
.end = DA850_MMCSD1_BASE + SZ_4K - 1,
.flags = IORESOURCE_MEM,
},
{ /* interrupt */
.start = IRQ_DA850_MMCSDINT0_1,
.end = IRQ_DA850_MMCSDINT0_1,
.flags = IORESOURCE_IRQ,
},
{ /* DMA RX */
.start = EDMA_CTLR_CHAN(1, 28),
.end = EDMA_CTLR_CHAN(1, 28),
.flags = IORESOURCE_DMA,
},
{ /* DMA TX */
.start = EDMA_CTLR_CHAN(1, 29),
.end = EDMA_CTLR_CHAN(1, 29),
.flags = IORESOURCE_DMA,
},
};
static struct platform_device da850_mmcsd1_device = {
.name = "davinci_mmc",
.id = 1,
.num_resources = ARRAY_SIZE(da850_mmcsd1_resources),
.resource = da850_mmcsd1_resources,
};
int __init da850_register_mmcsd1(struct davinci_mmc_config *config)
{
da850_mmcsd1_device.dev.platform_data = config;
return platform_device_register(&da850_mmcsd1_device);
}
#endif
static struct resource da8xx_rtc_resources[] = {
{
.start = DA8XX_RTC_BASE,
......
arch/arm/mach-davinci/devices-tnetv107x.c
浏览文件 @ 7940a34b
......@@ -31,8 +31,10 @@
#define TNETV107X_TPTC0_BASE 0x01c10000
#define TNETV107X_TPTC1_BASE 0x01c10400
#define TNETV107X_WDOG_BASE 0x08086700
#define TNETV107X_TSC_BASE 0x08088500
#define TNETV107X_SDIO0_BASE 0x08088700
#define TNETV107X_SDIO1_BASE 0x08088800
#define TNETV107X_KEYPAD_BASE 0x08088a00
#define TNETV107X_ASYNC_EMIF_CNTRL_BASE 0x08200000
#define TNETV107X_ASYNC_EMIF_DATA_CE0_BASE 0x30000000
#define TNETV107X_ASYNC_EMIF_DATA_CE1_BASE 0x40000000
......@@ -298,12 +300,55 @@ static int __init nand_init(int chipsel, struct davinci_nand_pdata *data)
return platform_device_register(pdev);
}
static struct resource keypad_resources[] = {
{
.start = TNETV107X_KEYPAD_BASE,
.end = TNETV107X_KEYPAD_BASE + 0xff,
.flags = IORESOURCE_MEM,
},
{
.start = IRQ_TNETV107X_KEYPAD,
.flags = IORESOURCE_IRQ,
.name = "press",
},
{
.start = IRQ_TNETV107X_KEYPAD_FREE,
.flags = IORESOURCE_IRQ,
.name = "release",
},
};
static struct platform_device keypad_device = {
.name = "tnetv107x-keypad",
.num_resources = ARRAY_SIZE(keypad_resources),
.resource = keypad_resources,
};
static struct resource tsc_resources[] = {
{
.start = TNETV107X_TSC_BASE,
.end = TNETV107X_TSC_BASE + 0xff,
.flags = IORESOURCE_MEM,
},
{
.start = IRQ_TNETV107X_TSC,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device tsc_device = {
.name = "tnetv107x-ts",
.num_resources = ARRAY_SIZE(tsc_resources),
.resource = tsc_resources,
};
void __init tnetv107x_devices_init(struct tnetv107x_device_info *info)
{
int i;
platform_device_register(&edma_device);
platform_device_register(&tnetv107x_wdt_device);
platform_device_register(&tsc_device);
if (info->serial_config)
davinci_serial_init(info->serial_config);
......@@ -317,4 +362,9 @@ void __init tnetv107x_devices_init(struct tnetv107x_device_info *info)
for (i = 0; i < 4; i++)
if (info->nand_config[i])
nand_init(i, info->nand_config[i]);
if (info->keypad_config) {
keypad_device.dev.platform_data = info->keypad_config;
platform_device_register(&keypad_device);
}
}
arch/arm/mach-davinci/devices.c
浏览文件 @ 7940a34b
......@@ -213,7 +213,7 @@ void __init davinci_setup_mmc(int module, struct davinci_mmc_config *config)
IO_ADDRESS(DAVINCI_SYSTEM_MODULE_BASE + 0x7c);
/* Configure pull down control */
__raw_writel((__raw_readl(pupdctl1) & ~0x400),
__raw_writel((__raw_readl(pupdctl1) & ~0xfc0),
pupdctl1);
mmcsd1_resources[0].start = DM365_MMCSD1_BASE;
......
arch/arm/mach-davinci/dm365.c
浏览文件 @ 7940a34b
......@@ -691,7 +691,6 @@ static struct emac_platform_data dm365_emac_pdata = {
.ctrl_reg_offset = DM365_EMAC_CNTRL_OFFSET,
.ctrl_mod_reg_offset = DM365_EMAC_CNTRL_MOD_OFFSET,
.ctrl_ram_offset = DM365_EMAC_CNTRL_RAM_OFFSET,
.mdio_reg_offset = DM365_EMAC_MDIO_OFFSET,
.ctrl_ram_size = DM365_EMAC_CNTRL_RAM_SIZE,
.version = EMAC_VERSION_2,
};
......@@ -699,7 +698,7 @@ static struct emac_platform_data dm365_emac_pdata = {
static struct resource dm365_emac_resources[] = {
{
.start = DM365_EMAC_BASE,
.end = DM365_EMAC_BASE + 0x47ff,
.end = DM365_EMAC_BASE + SZ_16K - 1,
.flags = IORESOURCE_MEM,
},
{
......@@ -734,6 +733,21 @@ static struct platform_device dm365_emac_device = {
.resource = dm365_emac_resources,
};
static struct resource dm365_mdio_resources[] = {
{
.start = DM365_EMAC_MDIO_BASE,
.end = DM365_EMAC_MDIO_BASE + SZ_4K - 1,
.flags = IORESOURCE_MEM,
},
};
static struct platform_device dm365_mdio_device = {
.name = "davinci_mdio",
.id = 0,
.num_resources = ARRAY_SIZE(dm365_mdio_resources),
.resource = dm365_mdio_resources,
};
static u8 dm365_default_priorities[DAVINCI_N_AINTC_IRQ] = {
[IRQ_VDINT0] = 2,
[IRQ_VDINT1] = 6,
......@@ -1219,7 +1233,12 @@ static int __init dm365_init_devices(void)
davinci_cfg_reg(DM365_INT_EDMA_CC);
platform_device_register(&dm365_edma_device);
platform_device_register(&dm365_mdio_device);
platform_device_register(&dm365_emac_device);
clk_add_alias(NULL, dev_name(&dm365_mdio_device.dev),
NULL, &dm365_emac_device.dev);
/* Add isif clock alias */
clk_add_alias("master", dm365_isif_dev.name, "vpss_master", NULL);
platform_device_register(&dm365_vpss_device);
......
arch/arm/mach-davinci/dm644x.c
浏览文件 @ 7940a34b
......@@ -322,7 +322,6 @@ static struct emac_platform_data dm644x_emac_pdata = {
.ctrl_reg_offset = DM644X_EMAC_CNTRL_OFFSET,
.ctrl_mod_reg_offset = DM644X_EMAC_CNTRL_MOD_OFFSET,
.ctrl_ram_offset = DM644X_EMAC_CNTRL_RAM_OFFSET,
.mdio_reg_offset = DM644X_EMAC_MDIO_OFFSET,
.ctrl_ram_size = DM644X_EMAC_CNTRL_RAM_SIZE,
.version = EMAC_VERSION_1,
};
......@@ -330,7 +329,7 @@ static struct emac_platform_data dm644x_emac_pdata = {
static struct resource dm644x_emac_resources[] = {
{
.start = DM644X_EMAC_BASE,
.end = DM644X_EMAC_BASE + 0x47ff,
.end = DM644X_EMAC_BASE + SZ_16K - 1,
.flags = IORESOURCE_MEM,
},
{
......@@ -350,6 +349,21 @@ static struct platform_device dm644x_emac_device = {
.resource = dm644x_emac_resources,
};
static struct resource dm644x_mdio_resources[] = {
{
.start = DM644X_EMAC_MDIO_BASE,
.end = DM644X_EMAC_MDIO_BASE + SZ_4K - 1,
.flags = IORESOURCE_MEM,
},
};
static struct platform_device dm644x_mdio_device = {
.name = "davinci_mdio",
.id = 0,
.num_resources = ARRAY_SIZE(dm644x_mdio_resources),
.resource = dm644x_mdio_resources,
};
/*
* Device specific mux setup
*
......@@ -776,7 +790,12 @@ static int __init dm644x_init_devices(void)
clk_add_alias("master", dm644x_ccdc_dev.name, "vpss_master", NULL);
clk_add_alias("slave", dm644x_ccdc_dev.name, "vpss_slave", NULL);
platform_device_register(&dm644x_edma_device);
platform_device_register(&dm644x_mdio_device);
platform_device_register(&dm644x_emac_device);
clk_add_alias(NULL, dev_name(&dm644x_mdio_device.dev),
NULL, &dm644x_emac_device.dev);
platform_device_register(&dm644x_vpss_device);
platform_device_register(&dm644x_ccdc_dev);
platform_device_register(&vpfe_capture_dev);
......
arch/arm/mach-davinci/dm646x.c
浏览文件 @ 7940a34b
......@@ -358,7 +358,6 @@ static struct emac_platform_data dm646x_emac_pdata = {
.ctrl_reg_offset = DM646X_EMAC_CNTRL_OFFSET,
.ctrl_mod_reg_offset = DM646X_EMAC_CNTRL_MOD_OFFSET,
.ctrl_ram_offset = DM646X_EMAC_CNTRL_RAM_OFFSET,
.mdio_reg_offset = DM646X_EMAC_MDIO_OFFSET,
.ctrl_ram_size = DM646X_EMAC_CNTRL_RAM_SIZE,
.version = EMAC_VERSION_2,
};
......@@ -366,7 +365,7 @@ static struct emac_platform_data dm646x_emac_pdata = {
static struct resource dm646x_emac_resources[] = {
{
.start = DM646X_EMAC_BASE,
.end = DM646X_EMAC_BASE + 0x47ff,
.end = DM646X_EMAC_BASE + SZ_16K - 1,
.flags = IORESOURCE_MEM,
},
{
......@@ -401,6 +400,21 @@ static struct platform_device dm646x_emac_device = {
.resource = dm646x_emac_resources,
};
static struct resource dm646x_mdio_resources[] = {
{
.start = DM646X_EMAC_MDIO_BASE,
.end = DM646X_EMAC_MDIO_BASE + SZ_4K - 1,
.flags = IORESOURCE_MEM,
},
};
static struct platform_device dm646x_mdio_device = {
.name = "davinci_mdio",
.id = 0,
.num_resources = ARRAY_SIZE(dm646x_mdio_resources),
.resource = dm646x_mdio_resources,
};
/*
* Device specific mux setup
*
......@@ -896,7 +910,11 @@ static int __init dm646x_init_devices(void)
if (!cpu_is_davinci_dm646x())
return 0;
platform_device_register(&dm646x_mdio_device);
platform_device_register(&dm646x_emac_device);
clk_add_alias(NULL, dev_name(&dm646x_mdio_device.dev),
NULL, &dm646x_emac_device.dev);
return 0;
}
postcore_initcall(dm646x_init_devices);
arch/arm/mach-davinci/dma.c
浏览文件 @ 7940a34b
......@@ -354,10 +354,12 @@ static int irq2ctlr(int irq)
static irqreturn_t dma_irq_handler(int irq, void *data)
{
int i;
unsigned ctlr;
int ctlr;
unsigned int cnt = 0;
ctlr = irq2ctlr(irq);
if (ctlr < 0)
return IRQ_NONE;
dev_dbg(data, "dma_irq_handler\n");
......@@ -408,10 +410,12 @@ static irqreturn_t dma_irq_handler(int irq, void *data)
static irqreturn_t dma_ccerr_handler(int irq, void *data)
{
int i;
unsigned ctlr;
int ctlr;
unsigned int cnt = 0;
ctlr = irq2ctlr(irq);
if (ctlr < 0)
return IRQ_NONE;
dev_dbg(data, "dma_ccerr_handler\n");
......
arch/arm/mach-davinci/include/mach/aemif.h 0 → 100644
浏览文件 @ 7940a34b
/*
* TI DaVinci AEMIF support
*
* Copyright 2010 (C) Texas Instruments, Inc. http://www.ti.com/
*
* This file is licensed under the terms of the GNU General Public License
* version 2. This program is licensed "as is" without any warranty of any
* kind, whether express or implied.
*/
#ifndef _MACH_DAVINCI_AEMIF_H
#define _MACH_DAVINCI_AEMIF_H
#define NRCSR_OFFSET 0x00
#define AWCCR_OFFSET 0x04
#define A1CR_OFFSET 0x10
#define ACR_ASIZE_MASK 0x3
#define ACR_EW_MASK BIT(30)
#define ACR_SS_MASK BIT(31)
/* All timings in nanoseconds */
struct davinci_aemif_timing {
u8 wsetup;
u8 wstrobe;
u8 whold;
u8 rsetup;
u8 rstrobe;
u8 rhold;
u8 ta;
};
int davinci_aemif_setup_timing(struct davinci_aemif_timing *t,
void __iomem *base, unsigned cs);
#endif
arch/arm/mach-davinci/include/mach/da8xx.h
浏览文件 @ 7940a34b
......@@ -76,9 +76,10 @@ int da8xx_register_usb11(struct da8xx_ohci_root_hub *pdata);
int da8xx_register_emac(void);
int da8xx_register_lcdc(struct da8xx_lcdc_platform_data *pdata);
int da8xx_register_mmcsd0(struct davinci_mmc_config *config);
int da850_register_mmcsd1(struct davinci_mmc_config *config);
void __init da8xx_register_mcasp(int id, struct snd_platform_data *pdata);
int da8xx_register_rtc(void);
int da850_register_cpufreq(void);
int da850_register_cpufreq(char *async_clk);
int da8xx_register_cpuidle(void);
void __iomem * __init da8xx_get_mem_ctlr(void);
int da850_register_pm(struct platform_device *pdev);
......@@ -121,11 +122,9 @@ extern const short da850_uart2_pins[];
extern const short da850_i2c0_pins[];
extern const short da850_i2c1_pins[];
extern const short da850_cpgmac_pins[];
extern const short da850_rmii_pins[];
extern const short da850_mcasp_pins[];
extern const short da850_lcdcntl_pins[];
extern const short da850_mmcsd0_pins[];
extern const short da850_nand_pins[];
extern const short da850_nor_pins[];
extern const short da850_emif25_pins[];
#endif /* __ASM_ARCH_DAVINCI_DA8XX_H */
arch/arm/mach-davinci/include/mach/dm365.h
浏览文件 @ 7940a34b
......@@ -21,10 +21,10 @@
#include <media/davinci/vpfe_capture.h>
#define DM365_EMAC_BASE (0x01D07000)
#define DM365_EMAC_MDIO_BASE (DM365_EMAC_BASE + 0x4000)
#define DM365_EMAC_CNTRL_OFFSET (0x0000)
#define DM365_EMAC_CNTRL_MOD_OFFSET (0x3000)
#define DM365_EMAC_CNTRL_RAM_OFFSET (0x1000)
#define DM365_EMAC_MDIO_OFFSET (0x4000)
#define DM365_EMAC_CNTRL_RAM_SIZE (0x2000)
/* Base of key scan register bank */
......
arch/arm/mach-davinci/include/mach/dm644x.h
浏览文件 @ 7940a34b
......@@ -28,10 +28,10 @@
#include <media/davinci/vpfe_capture.h>
#define DM644X_EMAC_BASE (0x01C80000)
#define DM644X_EMAC_MDIO_BASE (DM644X_EMAC_BASE + 0x4000)
#define DM644X_EMAC_CNTRL_OFFSET (0x0000)
#define DM644X_EMAC_CNTRL_MOD_OFFSET (0x1000)
#define DM644X_EMAC_CNTRL_RAM_OFFSET (0x2000)
#define DM644X_EMAC_MDIO_OFFSET (0x4000)
#define DM644X_EMAC_CNTRL_RAM_SIZE (0x2000)
#define DM644X_ASYNC_EMIF_CONTROL_BASE 0x01E00000
......
arch/arm/mach-davinci/include/mach/dm646x.h
浏览文件 @ 7940a34b
......@@ -19,10 +19,10 @@
#include <linux/davinci_emac.h>
#define DM646X_EMAC_BASE (0x01C80000)
#define DM646X_EMAC_MDIO_BASE (DM646X_EMAC_BASE + 0x4000)
#define DM646X_EMAC_CNTRL_OFFSET (0x0000)
#define DM646X_EMAC_CNTRL_MOD_OFFSET (0x1000)
#define DM646X_EMAC_CNTRL_RAM_OFFSET (0x2000)
#define DM646X_EMAC_MDIO_OFFSET (0x4000)
#define DM646X_EMAC_CNTRL_RAM_SIZE (0x2000)
#define DM646X_ASYNC_EMIF_CONTROL_BASE 0x20008000
......
arch/arm/mach-davinci/include/mach/nand.h
浏览文件 @ 7940a34b
......@@ -30,9 +30,6 @@
#include <linux/mtd/nand.h>
#define NRCSR_OFFSET 0x00
#define AWCCR_OFFSET 0x04
#define A1CR_OFFSET 0x10
#define NANDFCR_OFFSET 0x60
#define NANDFSR_OFFSET 0x64
#define NANDF1ECC_OFFSET 0x70
......@@ -83,6 +80,9 @@ struct davinci_nand_pdata { /* platform_data */
/* Main and mirror bbt descriptor overrides */
struct nand_bbt_descr *bbt_td;
struct nand_bbt_descr *bbt_md;
/* Access timings */
struct davinci_aemif_timing *timing;
};
#endif /* __ARCH_ARM_DAVINCI_NAND_H */
arch/arm/mach-davinci/include/mach/psc.h
浏览文件 @ 7940a34b
......@@ -172,6 +172,7 @@
#define DA8XX_LPSC1_UART2 13
#define DA8XX_LPSC1_LCDC 16
#define DA8XX_LPSC1_PWM 17
#define DA850_LPSC1_MMC_SD1 18
#define DA8XX_LPSC1_ECAP 20
#define DA830_LPSC1_EQEP 21
#define DA850_LPSC1_TPTC2 21
......
arch/arm/mach-davinci/include/mach/tnetv107x.h
浏览文件 @ 7940a34b
......@@ -33,6 +33,8 @@
#ifndef __ASSEMBLY__
#include <linux/serial_8250.h>
#include <linux/input/matrix_keypad.h>
#include <mach/mmc.h>
#include <mach/nand.h>
#include <mach/serial.h>
......@@ -41,6 +43,7 @@ struct tnetv107x_device_info {
struct davinci_uart_config *serial_config;
struct davinci_mmc_config *mmc_config[2]; /* 2 controllers */
struct davinci_nand_pdata *nand_config[4]; /* 4 chipsels */
struct matrix_keypad_platform_data *keypad_config;
};
extern struct platform_device tnetv107x_wdt_device;
......
arch/arm/mach-davinci/include/mach/uncompress.h
浏览文件 @ 7940a34b
......@@ -88,6 +88,8 @@ static inline void __arch_decomp_setup(unsigned long arch_id)
/* DA8xx boards */
DEBUG_LL_DA8XX(davinci_da830_evm, 2);
DEBUG_LL_DA8XX(davinci_da850_evm, 2);
DEBUG_LL_DA8XX(mityomapl138, 1);
DEBUG_LL_DA8XX(omapl138_hawkboard, 2);
/* TNETV107x boards */
DEBUG_LL_TNETV107X(tnetv107x, 1);
......
arch/arm/mach-davinci/tnetv107x.c
浏览文件 @ 7940a34b
......@@ -104,7 +104,7 @@ static u32 pll_ext_freq[] = {
};
/* PSC control registers */
static u32 psc_regs[] __initconst = { TNETV107X_PSC_BASE };
static u32 psc_regs[] = { TNETV107X_PSC_BASE };
/* Host map for interrupt controller */
static u32 intc_host_map[] = { 0x01010000, 0x01010101, -1 };
......@@ -581,7 +581,14 @@ static struct davinci_id ids[] = {
.part_no = 0xb8a1,
.manufacturer = 0x017,
.cpu_id = DAVINCI_CPU_ID_TNETV107X,
.name = "tnetv107x rev1.0",
.name = "tnetv107x rev 1.0",
},
{
.variant = 0x1,
.part_no = 0xb8a1,
.manufacturer = 0x017,
.cpu_id = DAVINCI_CPU_ID_TNETV107X,
.name = "tnetv107x rev 1.1/1.2",
},
};
......
arch/arm/mach-omap2/board-am3517evm.c
浏览文件 @ 7940a34b
......@@ -18,6 +18,7 @@
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/clk.h>
#include <linux/platform_device.h>
#include <linux/gpio.h>
#include <linux/i2c/pca953x.h>
......@@ -38,19 +39,37 @@
#include "mux.h"
#define AM35XX_EVM_PHY_MASK (0xF)
#define AM35XX_EVM_MDIO_FREQUENCY (1000000)
static struct mdio_platform_data am3517_evm_mdio_pdata = {
.bus_freq = AM35XX_EVM_MDIO_FREQUENCY,
};
static struct resource am3517_mdio_resources[] = {
{
.start = AM35XX_IPSS_EMAC_BASE + AM35XX_EMAC_MDIO_OFFSET,
.end = AM35XX_IPSS_EMAC_BASE + AM35XX_EMAC_MDIO_OFFSET +
SZ_4K - 1,
.flags = IORESOURCE_MEM,
},
};
static struct platform_device am3517_mdio_device = {
.name = "davinci_mdio",
.id = 0,
.num_resources = ARRAY_SIZE(am3517_mdio_resources),
.resource = am3517_mdio_resources,
.dev.platform_data = &am3517_evm_mdio_pdata,
};
static struct emac_platform_data am3517_evm_emac_pdata = {
.phy_mask = AM35XX_EVM_PHY_MASK,
.mdio_max_freq = AM35XX_EVM_MDIO_FREQUENCY,
.rmii_en = 1,
};
static struct resource am3517_emac_resources[] = {
{
.start = AM35XX_IPSS_EMAC_BASE,
.end = AM35XX_IPSS_EMAC_BASE + 0x3FFFF,
.end = AM35XX_IPSS_EMAC_BASE + 0x2FFFF,
.flags = IORESOURCE_MEM,
},
{
......@@ -113,7 +132,6 @@ void am3517_evm_ethernet_init(struct emac_platform_data *pdata)
pdata->ctrl_reg_offset = AM35XX_EMAC_CNTRL_OFFSET;
pdata->ctrl_mod_reg_offset = AM35XX_EMAC_CNTRL_MOD_OFFSET;
pdata->ctrl_ram_offset = AM35XX_EMAC_CNTRL_RAM_OFFSET;
pdata->mdio_reg_offset = AM35XX_EMAC_MDIO_OFFSET;
pdata->ctrl_ram_size = AM35XX_EMAC_CNTRL_RAM_SIZE;
pdata->version = EMAC_VERSION_2;
pdata->hw_ram_addr = AM35XX_EMAC_HW_RAM_ADDR;
......@@ -121,6 +139,9 @@ void am3517_evm_ethernet_init(struct emac_platform_data *pdata)
pdata->interrupt_disable = am3517_disable_ethernet_int;
am3517_emac_device.dev.platform_data = pdata;
platform_device_register(&am3517_emac_device);
platform_device_register(&am3517_mdio_device);
clk_add_alias(NULL, dev_name(&am3517_mdio_device.dev),
NULL, &am3517_emac_device.dev);
regval = omap_ctrl_readl(AM35XX_CONTROL_IP_SW_RESET);
regval = regval & (~(AM35XX_CPGMACSS_SW_RST));
......
drivers/input/keyboard/Kconfig
浏览文件 @ 7940a34b
......@@ -424,6 +424,15 @@ config KEYBOARD_OMAP
To compile this driver as a module, choose M here: the
module will be called omap-keypad.
config KEYBOARD_TNETV107X
tristate "TI TNETV107X keypad support"
depends on ARCH_DAVINCI_TNETV107X
help
Say Y here if you want to use the TNETV107X keypad.
To compile this driver as a module, choose M here: the
module will be called tnetv107x-keypad.
config KEYBOARD_TWL4030
tristate "TI TWL4030/TWL5030/TPS659x0 keypad support"
depends on TWL4030_CORE
......
drivers/input/keyboard/Makefile
浏览文件 @ 7940a34b
......@@ -38,6 +38,7 @@ obj-$(CONFIG_KEYBOARD_SH_KEYSC) += sh_keysc.o
obj-$(CONFIG_KEYBOARD_STMPE) += stmpe-keypad.o
obj-$(CONFIG_KEYBOARD_STOWAWAY) += stowaway.o
obj-$(CONFIG_KEYBOARD_SUNKBD) += sunkbd.o
obj-$(CONFIG_KEYBOARD_TNETV107X) += tnetv107x-keypad.o
obj-$(CONFIG_KEYBOARD_TWL4030) += twl4030_keypad.o
obj-$(CONFIG_KEYBOARD_XTKBD) += xtkbd.o
obj-$(CONFIG_KEYBOARD_W90P910) += w90p910_keypad.o
drivers/input/keyboard/tnetv107x-keypad.c 0 → 100644
浏览文件 @ 7940a34b
/*
* Texas Instruments TNETV107X Keypad Driver
*
* Copyright (C) 2010 Texas Instruments
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation version 2.
*
* This program is distributed "as is" WITHOUT ANY WARRANTY of any
* kind, whether express or implied; without even the implied warranty
* of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <linux/kernel.h>
#include <linux/errno.h>
#include <linux/input.h>
#include <linux/platform_device.h>
#include <linux/interrupt.h>
#include <linux/slab.h>
#include <linux/delay.h>
#include <linux/io.h>
#include <linux/clk.h>
#include <linux/input/matrix_keypad.h>
#define BITS(x) (BIT(x) - 1)
#define KEYPAD_ROWS 9
#define KEYPAD_COLS 9
#define DEBOUNCE_MIN 0x400ul
#define DEBOUNCE_MAX 0x3ffffffful
struct keypad_regs {
u32 rev;
u32 mode;
u32 mask;
u32 pol;
u32 dclock;
u32 rclock;
u32 stable_cnt;
u32 in_en;
u32 out;
u32 out_en;
u32 in;
u32 lock;
u32 pres[3];
};
#define keypad_read(kp, reg) __raw_readl(&(kp)->regs->reg)
#define keypad_write(kp, reg, val) __raw_writel(val, &(kp)->regs->reg)
struct keypad_data {
struct input_dev *input_dev;
struct resource *res;
struct keypad_regs __iomem *regs;
struct clk *clk;
struct device *dev;
spinlock_t lock;
u32 irq_press;
u32 irq_release;
int rows, cols, row_shift;
int debounce_ms, active_low;
u32 prev_keys[3];
unsigned short keycodes[];
};
static irqreturn_t keypad_irq(int irq, void *data)
{
struct keypad_data *kp = data;
int i, bit, val, row, col, code;
unsigned long flags;
u32 curr_keys[3];
u32 change;
spin_lock_irqsave(&kp->lock, flags);
memset(curr_keys, 0, sizeof(curr_keys));
if (irq == kp->irq_press)
for (i = 0; i < 3; i++)
curr_keys[i] = keypad_read(kp, pres[i]);
for (i = 0; i < 3; i++) {
change = curr_keys[i] ^ kp->prev_keys[i];
while (change) {
bit = fls(change) - 1;
change ^= BIT(bit);
val = curr_keys[i] & BIT(bit);
bit += i * 32;
row = bit / KEYPAD_COLS;
col = bit % KEYPAD_COLS;
code = MATRIX_SCAN_CODE(row, col, kp->row_shift);
input_event(kp->input_dev, EV_MSC, MSC_SCAN, code);
input_report_key(kp->input_dev, kp->keycodes[code],
val);
}
}
input_sync(kp->input_dev);
memcpy(kp->prev_keys, curr_keys, sizeof(curr_keys));
if (irq == kp->irq_press)
keypad_write(kp, lock, 0); /* Allow hardware updates */
spin_unlock_irqrestore(&kp->lock, flags);
return IRQ_HANDLED;
}
static int keypad_start(struct input_dev *dev)
{
struct keypad_data *kp = input_get_drvdata(dev);
unsigned long mask, debounce, clk_rate_khz;
unsigned long flags;
clk_enable(kp->clk);
clk_rate_khz = clk_get_rate(kp->clk) / 1000;
spin_lock_irqsave(&kp->lock, flags);
/* Initialize device registers */
keypad_write(kp, mode, 0);
mask = BITS(kp->rows) << KEYPAD_COLS;
mask |= BITS(kp->cols);
keypad_write(kp, mask, ~mask);
keypad_write(kp, pol, kp->active_low ? 0 : 0x3ffff);
keypad_write(kp, stable_cnt, 3);
debounce = kp->debounce_ms * clk_rate_khz;
debounce = clamp(debounce, DEBOUNCE_MIN, DEBOUNCE_MAX);
keypad_write(kp, dclock, debounce);
keypad_write(kp, rclock, 4 * debounce);
keypad_write(kp, in_en, 1);
spin_unlock_irqrestore(&kp->lock, flags);
return 0;
}
static void keypad_stop(struct input_dev *dev)
{
struct keypad_data *kp = input_get_drvdata(dev);
synchronize_irq(kp->irq_press);
synchronize_irq(kp->irq_release);
clk_disable(kp->clk);
}
static int __devinit keypad_probe(struct platform_device *pdev)
{
const struct matrix_keypad_platform_data *pdata;
const struct matrix_keymap_data *keymap_data;
struct device *dev = &pdev->dev;
struct keypad_data *kp;
int error = 0, sz, row_shift;
u32 rev = 0;
pdata = pdev->dev.platform_data;
if (!pdata) {
dev_err(dev, "cannot find device data\n");
return -EINVAL;
}
keymap_data = pdata->keymap_data;
if (!keymap_data) {
dev_err(dev, "cannot find keymap data\n");
return -EINVAL;
}
row_shift = get_count_order(pdata->num_col_gpios);
sz = offsetof(struct keypad_data, keycodes);
sz += (pdata->num_row_gpios << row_shift) * sizeof(kp->keycodes[0]);
kp = kzalloc(sz, GFP_KERNEL);
if (!kp) {
dev_err(dev, "cannot allocate device info\n");
return -ENOMEM;
}
kp->dev = dev;
kp->rows = pdata->num_row_gpios;
kp->cols = pdata->num_col_gpios;
kp->row_shift = row_shift;
platform_set_drvdata(pdev, kp);
spin_lock_init(&kp->lock);
kp->irq_press = platform_get_irq_byname(pdev, "press");
kp->irq_release = platform_get_irq_byname(pdev, "release");
if (kp->irq_press < 0 || kp->irq_release < 0) {
dev_err(dev, "cannot determine device interrupts\n");
error = -ENODEV;
goto error_res;
}
kp->res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!kp->res) {
dev_err(dev, "cannot determine register area\n");
error = -ENODEV;
goto error_res;
}
if (!request_mem_region(kp->res->start, resource_size(kp->res),
pdev->name)) {
dev_err(dev, "cannot claim register memory\n");
kp->res = NULL;
error = -EINVAL;
goto error_res;
}
kp->regs = ioremap(kp->res->start, resource_size(kp->res));
if (!kp->regs) {
dev_err(dev, "cannot map register memory\n");
error = -ENOMEM;
goto error_map;
}
kp->clk = clk_get(dev, NULL);
if (!kp->clk) {
dev_err(dev, "cannot claim device clock\n");
error = -EINVAL;
goto error_clk;
}
error = request_threaded_irq(kp->irq_press, NULL, keypad_irq, 0,
dev_name(dev), kp);
if (error < 0) {
dev_err(kp->dev, "Could not allocate keypad press key irq\n");
goto error_irq_press;
}
error = request_threaded_irq(kp->irq_release, NULL, keypad_irq, 0,
dev_name(dev), kp);
if (error < 0) {
dev_err(kp->dev, "Could not allocate keypad release key irq\n");
goto error_irq_release;
}
kp->input_dev = input_allocate_device();
if (!kp->input_dev) {
dev_err(dev, "cannot allocate input device\n");
error = -ENOMEM;
goto error_input;
}
input_set_drvdata(kp->input_dev, kp);
kp->input_dev->name = pdev->name;
kp->input_dev->dev.parent = &pdev->dev;
kp->input_dev->open = keypad_start;
kp->input_dev->close = keypad_stop;
kp->input_dev->evbit[0] = BIT_MASK(EV_KEY);
if (!pdata->no_autorepeat)
kp->input_dev->evbit[0] |= BIT_MASK(EV_REP);
clk_enable(kp->clk);
rev = keypad_read(kp, rev);
kp->input_dev->id.bustype = BUS_HOST;
kp->input_dev->id.product = ((rev >> 8) & 0x07);
kp->input_dev->id.version = ((rev >> 16) & 0xfff);
clk_disable(kp->clk);
kp->input_dev->keycode = kp->keycodes;
kp->input_dev->keycodesize = sizeof(kp->keycodes[0]);
kp->input_dev->keycodemax = kp->rows << kp->row_shift;
matrix_keypad_build_keymap(keymap_data, kp->row_shift, kp->keycodes,
kp->input_dev->keybit);
input_set_capability(kp->input_dev, EV_MSC, MSC_SCAN);
error = input_register_device(kp->input_dev);
if (error < 0) {
dev_err(dev, "Could not register input device\n");
goto error_reg;
}
return 0;
error_reg:
input_free_device(kp->input_dev);
error_input:
free_irq(kp->irq_release, kp);
error_irq_release:
free_irq(kp->irq_press, kp);
error_irq_press:
clk_put(kp->clk);
error_clk:
iounmap(kp->regs);
error_map:
release_mem_region(kp->res->start, resource_size(kp->res));
error_res:
platform_set_drvdata(pdev, NULL);
kfree(kp);
return error;
}
static int __devexit keypad_remove(struct platform_device *pdev)
{
struct keypad_data *kp = platform_get_drvdata(pdev);
free_irq(kp->irq_press, kp);
free_irq(kp->irq_release, kp);
input_unregister_device(kp->input_dev);
clk_put(kp->clk);
iounmap(kp->regs);
release_mem_region(kp->res->start, resource_size(kp->res));
platform_set_drvdata(pdev, NULL);
kfree(kp);
return 0;
}
static struct platform_driver keypad_driver = {
.probe = keypad_probe,
.remove = __devexit_p(keypad_remove),
.driver.name = "tnetv107x-keypad",
.driver.owner = THIS_MODULE,
};
static int __init keypad_init(void)
{
return platform_driver_register(&keypad_driver);
}
static void __exit keypad_exit(void)
{
platform_driver_unregister(&keypad_driver);
}
module_init(keypad_init);
module_exit(keypad_exit);
MODULE_AUTHOR("Cyril Chemparathy");
MODULE_DESCRIPTION("TNETV107X Keypad Driver");
MODULE_ALIAS("platform: tnetv107x-keypad");
MODULE_LICENSE("GPL");
drivers/input/touchscreen/Kconfig
浏览文件 @ 7940a34b
......@@ -328,6 +328,15 @@ config TOUCHSCREEN_MIGOR
To compile this driver as a module, choose M here: the
module will be called migor_ts.
config TOUCHSCREEN_TNETV107X
tristate "TI TNETV107X touchscreen support"
depends on ARCH_DAVINCI_TNETV107X
help
Say Y here if you want to use the TNETV107X touchscreen.
To compile this driver as a module, choose M here: the
module will be called tnetv107x-ts.
config TOUCHSCREEN_TOUCHRIGHT
tristate "Touchright serial touchscreen"
select SERIO
......
drivers/input/touchscreen/Makefile
浏览文件 @ 7940a34b
......@@ -37,6 +37,7 @@ obj-$(CONFIG_TOUCHSCREEN_PENMOUNT) += penmount.o
obj-$(CONFIG_TOUCHSCREEN_QT602240) += qt602240_ts.o
obj-$(CONFIG_TOUCHSCREEN_S3C2410) += s3c2410_ts.o
obj-$(CONFIG_TOUCHSCREEN_STMPE) += stmpe-ts.o
obj-$(CONFIG_TOUCHSCREEN_TNETV107X) += tnetv107x-ts.o
obj-$(CONFIG_TOUCHSCREEN_TOUCHIT213) += touchit213.o
obj-$(CONFIG_TOUCHSCREEN_TOUCHRIGHT) += touchright.o
obj-$(CONFIG_TOUCHSCREEN_TOUCHWIN) += touchwin.o
......
drivers/input/touchscreen/tnetv107x-ts.c 0 → 100644
浏览文件 @ 7940a34b
/*
* Texas Instruments TNETV107X Touchscreen Driver
*
* Copyright (C) 2010 Texas Instruments
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation version 2.
*
* This program is distributed "as is" WITHOUT ANY WARRANTY of any
* kind, whether express or implied; without even the implied warranty
* of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <linux/kernel.h>
#include <linux/errno.h>
#include <linux/input.h>
#include <linux/platform_device.h>
#include <linux/interrupt.h>
#include <linux/slab.h>
#include <linux/delay.h>
#include <linux/ctype.h>
#include <linux/io.h>
#include <linux/clk.h>
#include <mach/tnetv107x.h>
#define TSC_PENUP_POLL (HZ / 5)
#define IDLE_TIMEOUT 100 /* msec */
/*
* The first and last samples of a touch interval are usually garbage and need
* to be filtered out with these devices. The following definitions control
* the number of samples skipped.
*/
#define TSC_HEAD_SKIP 1
#define TSC_TAIL_SKIP 1
#define TSC_SKIP (TSC_HEAD_SKIP + TSC_TAIL_SKIP + 1)
#define TSC_SAMPLES (TSC_SKIP + 1)
/* Register Offsets */
struct tsc_regs {
u32 rev;
u32 tscm;
u32 bwcm;
u32 swc;
u32 adcchnl;
u32 adcdata;
u32 chval[4];
};
/* TSC Mode Configuration Register (tscm) bits */
#define WMODE BIT(0)
#define TSKIND BIT(1)
#define ZMEASURE_EN BIT(2)
#define IDLE BIT(3)
#define TSC_EN BIT(4)
#define STOP BIT(5)
#define ONE_SHOT BIT(6)
#define SINGLE BIT(7)
#define AVG BIT(8)
#define AVGNUM(x) (((x) & 0x03) << 9)
#define PVSTC(x) (((x) & 0x07) << 11)
#define PON BIT(14)
#define PONBG BIT(15)
#define AFERST BIT(16)
/* ADC DATA Capture Register bits */
#define DATA_VALID BIT(16)
/* Register Access Macros */
#define tsc_read(ts, reg) __raw_readl(&(ts)->regs->reg)
#define tsc_write(ts, reg, val) __raw_writel(val, &(ts)->regs->reg);
#define tsc_set_bits(ts, reg, val) \
tsc_write(ts, reg, tsc_read(ts, reg) | (val))
#define tsc_clr_bits(ts, reg, val) \
tsc_write(ts, reg, tsc_read(ts, reg) & ~(val))
struct sample {
int x, y, p;
};
struct tsc_data {
struct input_dev *input_dev;
struct resource *res;
struct tsc_regs __iomem *regs;
struct timer_list timer;
spinlock_t lock;
struct clk *clk;
struct device *dev;
int sample_count;
struct sample samples[TSC_SAMPLES];
int tsc_irq;
};
static int tsc_read_sample(struct tsc_data *ts, struct sample* sample)
{
int x, y, z1, z2, t, p = 0;
u32 val;
val = tsc_read(ts, chval[0]);
if (val & DATA_VALID)
x = val & 0xffff;
else
return -EINVAL;
y = tsc_read(ts, chval[1]) & 0xffff;
z1 = tsc_read(ts, chval[2]) & 0xffff;
z2 = tsc_read(ts, chval[3]) & 0xffff;
if (z1) {
t = ((600 * x) * (z2 - z1));
p = t / (u32) (z1 << 12);
if (p < 0)
p = 0;
}
sample->x = x;
sample->y = y;
sample->p = p;
return 0;
}
static void tsc_poll(unsigned long data)
{
struct tsc_data *ts = (struct tsc_data *)data;
unsigned long flags;
int i, val, x, y, p;
spin_lock_irqsave(&ts->lock, flags);
if (ts->sample_count >= TSC_SKIP) {
input_report_abs(ts->input_dev, ABS_PRESSURE, 0);
input_report_key(ts->input_dev, BTN_TOUCH, 0);
input_sync(ts->input_dev);
} else if (ts->sample_count > 0) {
/*
* A touch event lasted less than our skip count. Salvage and
* report anyway.
*/
for (i = 0, val = 0; i < ts->sample_count; i++)
val += ts->samples[i].x;
x = val / ts->sample_count;
for (i = 0, val = 0; i < ts->sample_count; i++)
val += ts->samples[i].y;
y = val / ts->sample_count;
for (i = 0, val = 0; i < ts->sample_count; i++)
val += ts->samples[i].p;
p = val / ts->sample_count;
input_report_abs(ts->input_dev, ABS_X, x);
input_report_abs(ts->input_dev, ABS_Y, y);
input_report_abs(ts->input_dev, ABS_PRESSURE, p);
input_report_key(ts->input_dev, BTN_TOUCH, 1);
input_sync(ts->input_dev);
}
ts->sample_count = 0;
spin_unlock_irqrestore(&ts->lock, flags);
}
static irqreturn_t tsc_irq(int irq, void *dev_id)
{
struct tsc_data *ts = (struct tsc_data *)dev_id;
struct sample *sample;
int index;
spin_lock(&ts->lock);
index = ts->sample_count % TSC_SAMPLES;
sample = &ts->samples[index];
if (tsc_read_sample(ts, sample) < 0)
goto out;
if (++ts->sample_count >= TSC_SKIP) {
index = (ts->sample_count - TSC_TAIL_SKIP - 1) % TSC_SAMPLES;
sample = &ts->samples[index];
input_report_abs(ts->input_dev, ABS_X, sample->x);
input_report_abs(ts->input_dev, ABS_Y, sample->y);
input_report_abs(ts->input_dev, ABS_PRESSURE, sample->p);
if (ts->sample_count == TSC_SKIP)
input_report_key(ts->input_dev, BTN_TOUCH, 1);
input_sync(ts->input_dev);
}
mod_timer(&ts->timer, jiffies + TSC_PENUP_POLL);
out:
spin_unlock(&ts->lock);
return IRQ_HANDLED;
}
static int tsc_start(struct input_dev *dev)
{
struct tsc_data *ts = input_get_drvdata(dev);
unsigned long timeout = jiffies + msecs_to_jiffies(IDLE_TIMEOUT);
u32 val;
clk_enable(ts->clk);
/* Go to idle mode, before any initialization */
while (time_after(timeout, jiffies)) {
if (tsc_read(ts, tscm) & IDLE)
break;
}
if (time_before(timeout, jiffies)) {
dev_warn(ts->dev, "timeout waiting for idle\n");
clk_disable(ts->clk);
return -EIO;
}
/* Configure TSC Control register*/
val = (PONBG | PON | PVSTC(4) | ONE_SHOT | ZMEASURE_EN);
tsc_write(ts, tscm, val);
/* Bring TSC out of reset: Clear AFE reset bit */
val &= ~(AFERST);
tsc_write(ts, tscm, val);
/* Configure all pins for hardware control*/
tsc_write(ts, bwcm, 0);
/* Finally enable the TSC */
tsc_set_bits(ts, tscm, TSC_EN);
return 0;
}
static void tsc_stop(struct input_dev *dev)
{
struct tsc_data *ts = input_get_drvdata(dev);
tsc_clr_bits(ts, tscm, TSC_EN);
synchronize_irq(ts->tsc_irq);
del_timer_sync(&ts->timer);
clk_disable(ts->clk);
}
static int __devinit tsc_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct tsc_data *ts;
int error = 0;
u32 rev = 0;
ts = kzalloc(sizeof(struct tsc_data), GFP_KERNEL);
if (!ts) {
dev_err(dev, "cannot allocate device info\n");
return -ENOMEM;
}
ts->dev = dev;
spin_lock_init(&ts->lock);
setup_timer(&ts->timer, tsc_poll, (unsigned long)ts);
platform_set_drvdata(pdev, ts);
ts->tsc_irq = platform_get_irq(pdev, 0);
if (ts->tsc_irq < 0) {
dev_err(dev, "cannot determine device interrupt\n");
error = -ENODEV;
goto error_res;
}
ts->res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!ts->res) {
dev_err(dev, "cannot determine register area\n");
error = -ENODEV;
goto error_res;
}
if (!request_mem_region(ts->res->start, resource_size(ts->res),
pdev->name)) {
dev_err(dev, "cannot claim register memory\n");
ts->res = NULL;
error = -EINVAL;
goto error_res;
}
ts->regs = ioremap(ts->res->start, resource_size(ts->res));
if (!ts->regs) {
dev_err(dev, "cannot map register memory\n");
error = -ENOMEM;
goto error_map;
}
ts->clk = clk_get(dev, NULL);
if (!ts->clk) {
dev_err(dev, "cannot claim device clock\n");
error = -EINVAL;
goto error_clk;
}
error = request_threaded_irq(ts->tsc_irq, NULL, tsc_irq, 0,
dev_name(dev), ts);
if (error < 0) {
dev_err(ts->dev, "Could not allocate ts irq\n");
goto error_irq;
}
ts->input_dev = input_allocate_device();
if (!ts->input_dev) {
dev_err(dev, "cannot allocate input device\n");
error = -ENOMEM;
goto error_input;
}
input_set_drvdata(ts->input_dev, ts);
ts->input_dev->name = pdev->name;
ts->input_dev->id.bustype = BUS_HOST;
ts->input_dev->dev.parent = &pdev->dev;
ts->input_dev->open = tsc_start;
ts->input_dev->close = tsc_stop;
clk_enable(ts->clk);
rev = tsc_read(ts, rev);
ts->input_dev->id.product = ((rev >> 8) & 0x07);
ts->input_dev->id.version = ((rev >> 16) & 0xfff);
clk_disable(ts->clk);
__set_bit(EV_KEY, ts->input_dev->evbit);
__set_bit(EV_ABS, ts->input_dev->evbit);
__set_bit(BTN_TOUCH, ts->input_dev->keybit);
input_set_abs_params(ts->input_dev, ABS_X, 0, 0xffff, 5, 0);
input_set_abs_params(ts->input_dev, ABS_Y, 0, 0xffff, 5, 0);
input_set_abs_params(ts->input_dev, ABS_PRESSURE, 0, 4095, 128, 0);
error = input_register_device(ts->input_dev);
if (error < 0) {
dev_err(dev, "failed input device registration\n");
goto error_reg;
}
return 0;
error_reg:
input_free_device(ts->input_dev);
error_input:
free_irq(ts->tsc_irq, ts);
error_irq:
clk_put(ts->clk);
error_clk:
iounmap(ts->regs);
error_map:
release_mem_region(ts->res->start, resource_size(ts->res));
error_res:
platform_set_drvdata(pdev, NULL);
kfree(ts);
return error;
}
static int __devexit tsc_remove(struct platform_device *pdev)
{
struct tsc_data *ts = platform_get_drvdata(pdev);
input_unregister_device(ts->input_dev);
free_irq(ts->tsc_irq, ts);
clk_put(ts->clk);
iounmap(ts->regs);
release_mem_region(ts->res->start, resource_size(ts->res));
platform_set_drvdata(pdev, NULL);
kfree(ts);
return 0;
}
static struct platform_driver tsc_driver = {
.probe = tsc_probe,
.remove = __devexit_p(tsc_remove),
.driver.name = "tnetv107x-ts",
.driver.owner = THIS_MODULE,
};
static int __init tsc_init(void)
{
return platform_driver_register(&tsc_driver);
}
static void __exit tsc_exit(void)
{
platform_driver_unregister(&tsc_driver);
}
module_init(tsc_init);
module_exit(tsc_exit);
MODULE_AUTHOR("Cyril Chemparathy");
MODULE_DESCRIPTION("TNETV107X Touchscreen Driver");
MODULE_ALIAS("platform: tnetv107x-ts");
MODULE_LICENSE("GPL");
drivers/mtd/nand/davinci_nand.c
浏览文件 @ 7940a34b
......@@ -35,6 +35,7 @@
#include <linux/slab.h>
#include <mach/nand.h>
#include <mach/aemif.h>
#include <asm/mach-types.h>
......@@ -74,6 +75,8 @@ struct davinci_nand_info {
uint32_t mask_cle;
uint32_t core_chipsel;
struct davinci_aemif_timing *timing;
};
static DEFINE_SPINLOCK(davinci_nand_lock);
......@@ -478,36 +481,6 @@ static int nand_davinci_dev_ready(struct mtd_info *mtd)
return davinci_nand_readl(info, NANDFSR_OFFSET) & BIT(0);
}
static void __init nand_dm6446evm_flash_init(struct davinci_nand_info *info)
{
uint32_t regval, a1cr;
/*
* NAND FLASH timings @ PLL1 == 459 MHz
* - AEMIF.CLK freq = PLL1/6 = 459/6 = 76.5 MHz
* - AEMIF.CLK period = 1/76.5 MHz = 13.1 ns
*/
regval = 0
| (0 << 31) /* selectStrobe */
| (0 << 30) /* extWait (never with NAND) */
| (1 << 26) /* writeSetup 10 ns */
| (3 << 20) /* writeStrobe 40 ns */
| (1 << 17) /* writeHold 10 ns */
| (0 << 13) /* readSetup 10 ns */
| (3 << 7) /* readStrobe 60 ns */
| (0 << 4) /* readHold 10 ns */
| (3 << 2) /* turnAround ?? ns */
| (0 << 0) /* asyncSize 8-bit bus */
;
a1cr = davinci_nand_readl(info, A1CR_OFFSET);
if (a1cr != regval) {
dev_dbg(info->dev, "Warning: NAND config: Set A1CR " \
"reg to 0x%08x, was 0x%08x, should be done by " \
"bootloader.\n", regval, a1cr);
davinci_nand_writel(info, A1CR_OFFSET, regval);
}
}
/*----------------------------------------------------------------------*/
/* An ECC layout for using 4-bit ECC with small-page flash, storing
......@@ -611,6 +584,7 @@ static int __init nand_davinci_probe(struct platform_device *pdev)
info->chip.options = pdata->options;
info->chip.bbt_td = pdata->bbt_td;
info->chip.bbt_md = pdata->bbt_md;
info->timing = pdata->timing;
info->ioaddr = (uint32_t __force) vaddr;
......@@ -688,15 +662,25 @@ static int __init nand_davinci_probe(struct platform_device *pdev)
goto err_clk_enable;
}
/* EMIF timings should normally be set by the boot loader,
* especially after boot-from-NAND. The *only* reason to
* have this special casing for the DM6446 EVM is to work
* with boot-from-NOR ... with CS0 manually re-jumpered
* (after startup) so it addresses the NAND flash, not NOR.
* Even for dev boards, that's unusually rude...
/*
* Setup Async configuration register in case we did not boot from
* NAND and so bootloader did not bother to set it up.
*/
if (machine_is_davinci_evm())
nand_dm6446evm_flash_init(info);
val = davinci_nand_readl(info, A1CR_OFFSET + info->core_chipsel * 4);
/* Extended Wait is not valid and Select Strobe mode is not used */
val &= ~(ACR_ASIZE_MASK | ACR_EW_MASK | ACR_SS_MASK);
if (info->chip.options & NAND_BUSWIDTH_16)
val |= 0x1;
davinci_nand_writel(info, A1CR_OFFSET + info->core_chipsel * 4, val);
ret = davinci_aemif_setup_timing(info->timing, info->base,
info->core_chipsel);
if (ret < 0) {
dev_dbg(&pdev->dev, "NAND timing values setup fail\n");
goto err_timing;
}
spin_lock_irq(&davinci_nand_lock);
......@@ -809,6 +793,7 @@ static int __init nand_davinci_probe(struct platform_device *pdev)
return 0;
err_scan:
err_timing:
clk_disable(info->clk);
err_clk_enable:
......
drivers/net/Kconfig
浏览文件 @ 7940a34b
......@@ -954,6 +954,8 @@ config NET_NETX
config TI_DAVINCI_EMAC
tristate "TI DaVinci EMAC Support"
depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 )
select TI_DAVINCI_MDIO
select TI_DAVINCI_CPDMA
select PHYLIB
help
This driver supports TI's DaVinci Ethernet .
......@@ -961,6 +963,25 @@ config TI_DAVINCI_EMAC
To compile this driver as a module, choose M here: the module
will be called davinci_emac_driver. This is recommended.
config TI_DAVINCI_MDIO
tristate "TI DaVinci MDIO Support"
depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 )
select PHYLIB
help
This driver supports TI's DaVinci MDIO module.
To compile this driver as a module, choose M here: the module
will be called davinci_mdio. This is recommended.
config TI_DAVINCI_CPDMA
tristate "TI DaVinci CPDMA Support"
depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 )
help
This driver supports TI's DaVinci CPDMA dma engine.
To compile this driver as a module, choose M here: the module
will be called davinci_cpdma. This is recommended.
config DM9000
tristate "DM9000 support"
depends on ARM || BLACKFIN || MIPS
......
drivers/net/Makefile
浏览文件 @ 7940a34b
......@@ -7,6 +7,8 @@ obj-$(CONFIG_MDIO) += mdio.o
obj-$(CONFIG_PHYLIB) += phy/
obj-$(CONFIG_TI_DAVINCI_EMAC) += davinci_emac.o
obj-$(CONFIG_TI_DAVINCI_MDIO) += davinci_mdio.o
obj-$(CONFIG_TI_DAVINCI_CPDMA) += davinci_cpdma.o
obj-$(CONFIG_E1000) += e1000/
obj-$(CONFIG_E1000E) += e1000e/
......
drivers/net/davinci_cpdma.c 0 → 100644
浏览文件 @ 7940a34b
此差异已折叠。
drivers/net/davinci_cpdma.h 0 → 100644
浏览文件 @ 7940a34b
/*
* Texas Instruments CPDMA Driver
*
* Copyright (C) 2010 Texas Instruments
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation version 2.
*
* This program is distributed "as is" WITHOUT ANY WARRANTY of any
* kind, whether express or implied; without even the implied warranty
* of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#ifndef __DAVINCI_CPDMA_H__
#define __DAVINCI_CPDMA_H__
#define CPDMA_MAX_CHANNELS BITS_PER_LONG
#define tx_chan_num(chan) (chan)
#define rx_chan_num(chan) ((chan) + CPDMA_MAX_CHANNELS)
#define is_rx_chan(chan) ((chan)->chan_num >= CPDMA_MAX_CHANNELS)
#define is_tx_chan(chan) (!is_rx_chan(chan))
#define __chan_linear(chan_num) ((chan_num) & (CPDMA_MAX_CHANNELS - 1))
#define chan_linear(chan) __chan_linear((chan)->chan_num)
struct cpdma_params {
struct device *dev;
void __iomem *dmaregs;
void __iomem *txhdp, *rxhdp, *txcp, *rxcp;
void __iomem *rxthresh, *rxfree;
int num_chan;
bool has_soft_reset;
int min_packet_size;
u32 desc_mem_phys;
int desc_mem_size;
int desc_align;
/*
* Some instances of embedded cpdma controllers have extra control and
* status registers. The following flag enables access to these
* "extended" registers.
*/
bool has_ext_regs;
};
struct cpdma_chan_stats {
u32 head_enqueue;
u32 tail_enqueue;
u32 pad_enqueue;
u32 misqueued;
u32 desc_alloc_fail;
u32 pad_alloc_fail;
u32 runt_receive_buff;
u32 runt_transmit_buff;
u32 empty_dequeue;
u32 busy_dequeue;
u32 good_dequeue;
u32 requeue;
u32 teardown_dequeue;
};
struct cpdma_ctlr;
struct cpdma_chan;
typedef void (*cpdma_handler_fn)(void *token, int len, int status);
struct cpdma_ctlr *cpdma_ctlr_create(struct cpdma_params *params);
int cpdma_ctlr_destroy(struct cpdma_ctlr *ctlr);
int cpdma_ctlr_start(struct cpdma_ctlr *ctlr);
int cpdma_ctlr_stop(struct cpdma_ctlr *ctlr);
int cpdma_ctlr_dump(struct cpdma_ctlr *ctlr);
struct cpdma_chan *cpdma_chan_create(struct cpdma_ctlr *ctlr, int chan_num,
cpdma_handler_fn handler);
int cpdma_chan_destroy(struct cpdma_chan *chan);
int cpdma_chan_start(struct cpdma_chan *chan);
int cpdma_chan_stop(struct cpdma_chan *chan);
int cpdma_chan_dump(struct cpdma_chan *chan);
int cpdma_chan_get_stats(struct cpdma_chan *chan,
struct cpdma_chan_stats *stats);
int cpdma_chan_submit(struct cpdma_chan *chan, void *token, void *data,
int len, gfp_t gfp_mask);
int cpdma_chan_process(struct cpdma_chan *chan, int quota);
int cpdma_ctlr_int_ctrl(struct cpdma_ctlr *ctlr, bool enable);
void cpdma_ctlr_eoi(struct cpdma_ctlr *ctlr);
int cpdma_chan_int_ctrl(struct cpdma_chan *chan, bool enable);
enum cpdma_control {
CPDMA_CMD_IDLE, /* write-only */
CPDMA_COPY_ERROR_FRAMES, /* read-write */
CPDMA_RX_OFF_LEN_UPDATE, /* read-write */
CPDMA_RX_OWNERSHIP_FLIP, /* read-write */
CPDMA_TX_PRIO_FIXED, /* read-write */
CPDMA_STAT_IDLE, /* read-only */
CPDMA_STAT_TX_ERR_CHAN, /* read-only */
CPDMA_STAT_TX_ERR_CODE, /* read-only */
CPDMA_STAT_RX_ERR_CHAN, /* read-only */
CPDMA_STAT_RX_ERR_CODE, /* read-only */
CPDMA_RX_BUFFER_OFFSET, /* read-write */
};
int cpdma_control_get(struct cpdma_ctlr *ctlr, int control);
int cpdma_control_set(struct cpdma_ctlr *ctlr, int control, int value);
#endif
drivers/net/davinci_emac.c
浏览文件 @ 7940a34b
此差异已折叠。
drivers/net/davinci_mdio.c 0 → 100644
浏览文件 @ 7940a34b
/*
* DaVinci MDIO Module driver
*
* Copyright (C) 2010 Texas Instruments.
*
* Shamelessly ripped out of davinci_emac.c, original copyrights follow:
*
* Copyright (C) 2009 Texas Instruments.
*
* ---------------------------------------------------------------------------
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
* ---------------------------------------------------------------------------
*/
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/sched.h>
#include <linux/slab.h>
#include <linux/phy.h>
#include <linux/clk.h>
#include <linux/err.h>
#include <linux/io.h>
#include <linux/davinci_emac.h>
/*
* This timeout definition is a worst-case ultra defensive measure against
* unexpected controller lock ups. Ideally, we should never ever hit this
* scenario in practice.
*/
#define MDIO_TIMEOUT 100 /* msecs */
#define PHY_REG_MASK 0x1f
#define PHY_ID_MASK 0x1f
#define DEF_OUT_FREQ 2200000 /* 2.2 MHz */
struct davinci_mdio_regs {
u32 version;
u32 control;
#define CONTROL_IDLE BIT(31)
#define CONTROL_ENABLE BIT(30)
#define CONTROL_MAX_DIV (0xff)
u32 alive;
u32 link;
u32 linkintraw;
u32 linkintmasked;
u32 __reserved_0[2];
u32 userintraw;
u32 userintmasked;
u32 userintmaskset;
u32 userintmaskclr;
u32 __reserved_1[20];
struct {
u32 access;
#define USERACCESS_GO BIT(31)
#define USERACCESS_WRITE BIT(30)
#define USERACCESS_ACK BIT(29)
#define USERACCESS_READ (0)
#define USERACCESS_DATA (0xffff)
u32 physel;
} user[0];
};
struct mdio_platform_data default_pdata = {
.bus_freq = DEF_OUT_FREQ,
};
struct davinci_mdio_data {
struct mdio_platform_data pdata;
struct davinci_mdio_regs __iomem *regs;
spinlock_t lock;
struct clk *clk;
struct device *dev;
struct mii_bus *bus;
bool suspended;
unsigned long access_time; /* jiffies */
};
static void __davinci_mdio_reset(struct davinci_mdio_data *data)
{
u32 mdio_in, div, mdio_out_khz, access_time;
mdio_in = clk_get_rate(data->clk);
div = (mdio_in / data->pdata.bus_freq) - 1;
if (div > CONTROL_MAX_DIV)
div = CONTROL_MAX_DIV;
/* set enable and clock divider */
__raw_writel(div | CONTROL_ENABLE, &data->regs->control);
/*
* One mdio transaction consists of:
* 32 bits of preamble
* 32 bits of transferred data
* 24 bits of bus yield (not needed unless shared?)
*/
mdio_out_khz = mdio_in / (1000 * (div + 1));
access_time = (88 * 1000) / mdio_out_khz;
/*
* In the worst case, we could be kicking off a user-access immediately
* after the mdio bus scan state-machine triggered its own read. If
* so, our request could get deferred by one access cycle. We
* defensively allow for 4 access cycles.
*/
data->access_time = usecs_to_jiffies(access_time * 4);
if (!data->access_time)
data->access_time = 1;
}
static int davinci_mdio_reset(struct mii_bus *bus)
{
struct davinci_mdio_data *data = bus->priv;
u32 phy_mask, ver;
__davinci_mdio_reset(data);
/* wait for scan logic to settle */
msleep(PHY_MAX_ADDR * data->access_time);
/* dump hardware version info */
ver = __raw_readl(&data->regs->version);
dev_info(data->dev, "davinci mdio revision %d.%d\n",
(ver >> 8) & 0xff, ver & 0xff);
/* get phy mask from the alive register */
phy_mask = __raw_readl(&data->regs->alive);
if (phy_mask) {
/* restrict mdio bus to live phys only */
dev_info(data->dev, "detected phy mask %x\n", ~phy_mask);
phy_mask = ~phy_mask;
} else {
/* desperately scan all phys */
dev_warn(data->dev, "no live phy, scanning all\n");
phy_mask = 0;
}
data->bus->phy_mask = phy_mask;
return 0;
}
/* wait until hardware is ready for another user access */
static inline int wait_for_user_access(struct davinci_mdio_data *data)
{
struct davinci_mdio_regs __iomem *regs = data->regs;
unsigned long timeout = jiffies + msecs_to_jiffies(MDIO_TIMEOUT);
u32 reg;
while (time_after(timeout, jiffies)) {
reg = __raw_readl(&regs->user[0].access);
if ((reg & USERACCESS_GO) == 0)
return 0;
reg = __raw_readl(&regs->control);
if ((reg & CONTROL_IDLE) == 0)
continue;
/*
* An emac soft_reset may have clobbered the mdio controller's
* state machine. We need to reset and retry the current
* operation
*/
dev_warn(data->dev, "resetting idled controller\n");
__davinci_mdio_reset(data);
return -EAGAIN;
}
dev_err(data->dev, "timed out waiting for user access\n");
return -ETIMEDOUT;
}
/* wait until hardware state machine is idle */
static inline int wait_for_idle(struct davinci_mdio_data *data)
{
struct davinci_mdio_regs __iomem *regs = data->regs;
unsigned long timeout = jiffies + msecs_to_jiffies(MDIO_TIMEOUT);
while (time_after(timeout, jiffies)) {
if (__raw_readl(&regs->control) & CONTROL_IDLE)
return 0;
}
dev_err(data->dev, "timed out waiting for idle\n");
return -ETIMEDOUT;
}
static int davinci_mdio_read(struct mii_bus *bus, int phy_id, int phy_reg)
{
struct davinci_mdio_data *data = bus->priv;
u32 reg;
int ret;
if (phy_reg & ~PHY_REG_MASK || phy_id & ~PHY_ID_MASK)
return -EINVAL;
spin_lock(&data->lock);
if (data->suspended) {
spin_unlock(&data->lock);
return -ENODEV;
}
reg = (USERACCESS_GO | USERACCESS_READ | (phy_reg << 21) |
(phy_id << 16));
while (1) {
ret = wait_for_user_access(data);
if (ret == -EAGAIN)
continue;
if (ret < 0)
break;
__raw_writel(reg, &data->regs->user[0].access);
ret = wait_for_user_access(data);
if (ret == -EAGAIN)
continue;
if (ret < 0)
break;
reg = __raw_readl(&data->regs->user[0].access);
ret = (reg & USERACCESS_ACK) ? (reg & USERACCESS_DATA) : -EIO;
break;
}
spin_unlock(&data->lock);
return ret;
}
static int davinci_mdio_write(struct mii_bus *bus, int phy_id,
int phy_reg, u16 phy_data)
{
struct davinci_mdio_data *data = bus->priv;
u32 reg;
int ret;
if (phy_reg & ~PHY_REG_MASK || phy_id & ~PHY_ID_MASK)
return -EINVAL;
spin_lock(&data->lock);
if (data->suspended) {
spin_unlock(&data->lock);
return -ENODEV;
}
reg = (USERACCESS_GO | USERACCESS_WRITE | (phy_reg << 21) |
(phy_id << 16) | (phy_data & USERACCESS_DATA));
while (1) {
ret = wait_for_user_access(data);
if (ret == -EAGAIN)
continue;
if (ret < 0)
break;
__raw_writel(reg, &data->regs->user[0].access);
ret = wait_for_user_access(data);
if (ret == -EAGAIN)
continue;
break;
}
spin_unlock(&data->lock);
return 0;
}
static int __devinit davinci_mdio_probe(struct platform_device *pdev)
{
struct mdio_platform_data *pdata = pdev->dev.platform_data;
struct device *dev = &pdev->dev;
struct davinci_mdio_data *data;
struct resource *res;
struct phy_device *phy;
int ret, addr;
data = kzalloc(sizeof(*data), GFP_KERNEL);
if (!data) {
dev_err(dev, "failed to alloc device data\n");
return -ENOMEM;
}
data->pdata = pdata ? (*pdata) : default_pdata;
data->bus = mdiobus_alloc();
if (!data->bus) {
dev_err(dev, "failed to alloc mii bus\n");
ret = -ENOMEM;
goto bail_out;
}
data->bus->name = dev_name(dev);
data->bus->read = davinci_mdio_read,
data->bus->write = davinci_mdio_write,
data->bus->reset = davinci_mdio_reset,
data->bus->parent = dev;
data->bus->priv = data;
snprintf(data->bus->id, MII_BUS_ID_SIZE, "%x", pdev->id);
data->clk = clk_get(dev, NULL);
if (IS_ERR(data->clk)) {
data->clk = NULL;
dev_err(dev, "failed to get device clock\n");
ret = PTR_ERR(data->clk);
goto bail_out;
}
clk_enable(data->clk);
dev_set_drvdata(dev, data);
data->dev = dev;
spin_lock_init(&data->lock);
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!res) {
dev_err(dev, "could not find register map resource\n");
ret = -ENOENT;
goto bail_out;
}
res = devm_request_mem_region(dev, res->start, resource_size(res),
dev_name(dev));
if (!res) {
dev_err(dev, "could not allocate register map resource\n");
ret = -ENXIO;
goto bail_out;
}
data->regs = devm_ioremap_nocache(dev, res->start, resource_size(res));
if (!data->regs) {
dev_err(dev, "could not map mdio registers\n");
ret = -ENOMEM;
goto bail_out;
}
/* register the mii bus */
ret = mdiobus_register(data->bus);
if (ret)
goto bail_out;
/* scan and dump the bus */
for (addr = 0; addr < PHY_MAX_ADDR; addr++) {
phy = data->bus->phy_map[addr];
if (phy) {
dev_info(dev, "phy[%d]: device %s, driver %s\n",
phy->addr, dev_name(&phy->dev),
phy->drv ? phy->drv->name : "unknown");
}
}
return 0;
bail_out:
if (data->bus)
mdiobus_free(data->bus);
if (data->clk) {
clk_disable(data->clk);
clk_put(data->clk);
}
kfree(data);
return ret;
}
static int __devexit davinci_mdio_remove(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct davinci_mdio_data *data = dev_get_drvdata(dev);
if (data->bus)
mdiobus_free(data->bus);
if (data->clk) {
clk_disable(data->clk);
clk_put(data->clk);
}
dev_set_drvdata(dev, NULL);
kfree(data);
return 0;
}
static int davinci_mdio_suspend(struct device *dev)
{
struct davinci_mdio_data *data = dev_get_drvdata(dev);
u32 ctrl;
spin_lock(&data->lock);
/* shutdown the scan state machine */
ctrl = __raw_readl(&data->regs->control);
ctrl &= ~CONTROL_ENABLE;
__raw_writel(ctrl, &data->regs->control);
wait_for_idle(data);
if (data->clk)
clk_disable(data->clk);
data->suspended = true;
spin_unlock(&data->lock);
return 0;
}
static int davinci_mdio_resume(struct device *dev)
{
struct davinci_mdio_data *data = dev_get_drvdata(dev);
u32 ctrl;
spin_lock(&data->lock);
if (data->clk)
clk_enable(data->clk);
/* restart the scan state machine */
ctrl = __raw_readl(&data->regs->control);
ctrl |= CONTROL_ENABLE;
__raw_writel(ctrl, &data->regs->control);
data->suspended = false;
spin_unlock(&data->lock);
return 0;
}
static const struct dev_pm_ops davinci_mdio_pm_ops = {
.suspend = davinci_mdio_suspend,
.resume = davinci_mdio_resume,
};
static struct platform_driver davinci_mdio_driver = {
.driver = {
.name = "davinci_mdio",
.owner = THIS_MODULE,
.pm = &davinci_mdio_pm_ops,
},
.probe = davinci_mdio_probe,
.remove = __devexit_p(davinci_mdio_remove),
};
static int __init davinci_mdio_init(void)
{
return platform_driver_register(&davinci_mdio_driver);
}
device_initcall(davinci_mdio_init);
static void __exit davinci_mdio_exit(void)
{
platform_driver_unregister(&davinci_mdio_driver);
}
module_exit(davinci_mdio_exit);
MODULE_LICENSE("GPL");
MODULE_DESCRIPTION("DaVinci MDIO driver");
include/linux/davinci_emac.h
浏览文件 @ 7940a34b
......@@ -14,16 +14,26 @@
#include <linux/if_ether.h>
#include <linux/memory.h>
struct mdio_platform_data {
unsigned long bus_freq;
};
struct emac_platform_data {
char mac_addr[ETH_ALEN];
u32 ctrl_reg_offset;
u32 ctrl_mod_reg_offset;
u32 ctrl_ram_offset;
u32 hw_ram_addr;
u32 mdio_reg_offset;
u32 ctrl_ram_size;
u32 phy_mask;
u32 mdio_max_freq;
/*
* phy_id can be one of the following:
* - NULL : use the first phy on the bus,
* - "" : force to 100/full, no mdio control
* - "<bus>:<addr>" : use the specified bus and phy
*/
const char *phy_id;
u8 rmii_en;
u8 version;
void (*interrupt_enable) (void);
......
Markdown is supported
0% 或 .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑！
想要评论请 注册 或