Merge tag 'extcon-next-for-5.4' of...

Merge tag 'extcon-next-for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-next

Chanwoo writes:

Update extcon for 5.4

Detailed description for this pull request:
1. Clean up the and fix the minor issue of extcon provider driver
- extcon-arizona/max77843 replace the helper function
  with more correct helper function without operation changes.
- extcon-fsa9480 supports the FSA880 variant by adding the compatible name.
- extcon-arizona updates the dt-binding file for the readability.
- extcon-gpio initializes the interrupt flags according to active-low state.
- Clean up extcon-sm5502/axp288/adc-jack

* tag 'extcon-next-for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon:
  extcon: adc-jack: Remove dev_err() usage after platform_get_irq()
  extcon: axp288: Use for_each_set_bit() in axp288_extcon_log_rsi()
  extcon: axp288: Add missed error check
  extcon: sm5502: Add IRQ_ONESHOT
  extcon: gpio: Request reasonable interrupts
  extcon: arizona: Update binding example to use available defines
  extcon: fsa9480: Support the FSA880 variant
  extcon: extcon-max77843: convert to i2c_new_dummy_device
  extcon: arizona: Switch to use device_property_count_u32()

Documentation/devicetree/bindings/extcon/extcon-arizona.txt

@@ -72,5 +72,5 @@ codec: wm8280@0 {
 		1 2 1 /* MICDET2 MICBIAS2 GPIO=high */
 	>;
 
-	wlf,gpsw = <0>;
+	wlf,gpsw = <ARIZONA_GPSW_OPEN>;
 };

Documentation/devicetree/bindings/extcon/extcon-fsa9480.txt

@@ -5,7 +5,9 @@ controlled using I2C and enables USB data, stereo and mono audio, video,
 microphone, and UART data to use a common connector port.
 
 Required properties:
- - compatible : Must be "fcs,fsa9480"
+ - compatible : Must be one of
+   "fcs,fsa9480"
+   "fcs,fsa880"
  - reg : Specifies i2c slave address. Must be 0x25.
  - interrupts : Should contain one entry specifying interrupt signal of
    interrupt parent to which interrupt pin of the chip is connected.

drivers/extcon/extcon-adc-jack.c

@@ -140,10 +140,8 @@ static int adc_jack_probe(struct platform_device *pdev)
 		return err;
 
 	data->irq = platform_get_irq(pdev, 0);
-	if (data->irq < 0) {
-		dev_err(&pdev->dev, "platform_get_irq failed\n");
+	if (data->irq < 0)
 		return -ENODEV;
-	}
 
 	err = request_any_context_irq(data->irq, adc_jack_irq_thread,
 			pdata->irq_flags, pdata->name, data);

drivers/extcon/extcon-arizona.c

@@ -1253,7 +1253,7 @@ static int arizona_extcon_get_micd_configs(struct device *dev,
 	int i, j;
 	u32 *vals;
 
-	nconfs = device_property_read_u32_array(arizona->dev, prop, NULL, 0);
+	nconfs = device_property_count_u32(arizona->dev, prop);
 	if (nconfs <= 0)
 		return 0;
 

drivers/extcon/extcon-axp288.c

@@ -121,7 +121,6 @@ static const char * const axp288_pwr_up_down_info[] = {
 	"Last shutdown caused by PMIC UVLO threshold",
 	"Last shutdown caused by SOC initiated cold off",
 	"Last shutdown caused by user pressing the power button",
-	NULL,
 };
 
 /*
@@ -130,18 +129,21 @@ static const char * const axp288_pwr_up_down_info[] = {
  */
 static void axp288_extcon_log_rsi(struct axp288_extcon_info *info)
 {
-	const char * const *rsi;
 	unsigned int val, i, clear_mask = 0;
+	unsigned long bits;
 	int ret;
 
 	ret = regmap_read(info->regmap, AXP288_PS_BOOT_REASON_REG, &val);
-	for (i = 0, rsi = axp288_pwr_up_down_info; *rsi; rsi++, i++) {
-		if (val & BIT(i)) {
-			dev_dbg(info->dev, "%s\n", *rsi);
-			clear_mask |= BIT(i);
-		}
+	if (ret < 0) {
+		dev_err(info->dev, "failed to read reset source indicator\n");
+		return;
 	}
 
+	bits = val & GENMASK(ARRAY_SIZE(axp288_pwr_up_down_info) - 1, 0);
+	for_each_set_bit(i, &bits, ARRAY_SIZE(axp288_pwr_up_down_info))
+		dev_dbg(info->dev, "%s\n", axp288_pwr_up_down_info[i]);
+	clear_mask = bits;
+
 	/* Clear the register value for next reboot (write 1 to clear bit) */
 	regmap_write(info->regmap, AXP288_PS_BOOT_REASON_REG, clear_mask);
 }

drivers/extcon/extcon-fsa9480.c

@@ -363,6 +363,7 @@ MODULE_DEVICE_TABLE(i2c, fsa9480_id);
 
 static const struct of_device_id fsa9480_of_match[] = {
 	{ .compatible = "fcs,fsa9480", },
+	{ .compatible = "fcs,fsa880", },
 	{ },
 };
 MODULE_DEVICE_TABLE(of, fsa9480_of_match);

drivers/extcon/extcon-gpio.c

@@ -22,26 +22,22 @@
 /**
  * struct gpio_extcon_data - A simple GPIO-controlled extcon device state container.
  * @edev:		Extcon device.
- * @irq:		Interrupt line for the external connector.
  * @work:		Work fired by the interrupt.
  * @debounce_jiffies:	Number of jiffies to wait for the GPIO to stabilize, from the debounce
  *			value.
  * @gpiod:		GPIO descriptor for this external connector.
  * @extcon_id:		The unique id of specific external connector.
  * @debounce:		Debounce time for GPIO IRQ in ms.
- * @irq_flags:		IRQ Flags (e.g., IRQF_TRIGGER_LOW).
  * @check_on_resume:	Boolean describing whether to check the state of gpio
  *			while resuming from sleep.
  */
 struct gpio_extcon_data {
 	struct extcon_dev *edev;
-	int irq;
 	struct delayed_work work;
 	unsigned long debounce_jiffies;
 	struct gpio_desc *gpiod;
 	unsigned int extcon_id;
 	unsigned long debounce;
-	unsigned long irq_flags;
 	bool check_on_resume;
 };
 
@@ -69,6 +65,8 @@ static int gpio_extcon_probe(struct platform_device *pdev)
 {
 	struct gpio_extcon_data *data;
 	struct device *dev = &pdev->dev;
+	unsigned long irq_flags;
+	int irq;
 	int ret;
 
 	data = devm_kzalloc(dev, sizeof(struct gpio_extcon_data), GFP_KERNEL);
@@ -82,15 +80,26 @@ static int gpio_extcon_probe(struct platform_device *pdev)
 	 * developed to get the extcon id from device-tree or others.
 	 * On later, it have to be solved.
 	 */
-	if (!data->irq_flags || data->extcon_id > EXTCON_NONE)
+	if (data->extcon_id > EXTCON_NONE)
 		return -EINVAL;
 
 	data->gpiod = devm_gpiod_get(dev, "extcon", GPIOD_IN);
 	if (IS_ERR(data->gpiod))
 		return PTR_ERR(data->gpiod);
-	data->irq = gpiod_to_irq(data->gpiod);
-	if (data->irq <= 0)
-		return data->irq;
+	irq = gpiod_to_irq(data->gpiod);
+	if (irq <= 0)
+		return irq;
+
+	/*
+	 * It is unlikely that this is an acknowledged interrupt that goes
+	 * away after handling, what we are looking for are falling edges
+	 * if the signal is active low, and rising edges if the signal is
+	 * active high.
+	 */
+	if (gpiod_is_active_low(data->gpiod))
+		irq_flags = IRQF_TRIGGER_FALLING;
+	else
+		irq_flags = IRQF_TRIGGER_RISING;
 
 	/* Allocate the memory of extcon devie and register extcon device */
 	data->edev = devm_extcon_dev_allocate(dev, &data->extcon_id);
@@ -109,8 +118,8 @@ static int gpio_extcon_probe(struct platform_device *pdev)
 	 * Request the interrupt of gpio to detect whether external connector
 	 * is attached or detached.
 	 */
-	ret = devm_request_any_context_irq(dev, data->irq,
-					gpio_irq_handler, data->irq_flags,
+	ret = devm_request_any_context_irq(dev, irq,
+					gpio_irq_handler, irq_flags,
 					pdev->name, data);
 	if (ret < 0)
 		return ret;

drivers/extcon/extcon-max77843.c

@@ -774,12 +774,12 @@ static int max77843_init_muic_regmap(struct max77693_dev *max77843)
 {
 	int ret;
 
-	max77843->i2c_muic = i2c_new_dummy(max77843->i2c->adapter,
+	max77843->i2c_muic = i2c_new_dummy_device(max77843->i2c->adapter,
 			I2C_ADDR_MUIC);
-	if (!max77843->i2c_muic) {
+	if (IS_ERR(max77843->i2c_muic)) {
 		dev_err(&max77843->i2c->dev,
 				"Cannot allocate I2C device for MUIC\n");
-		return -ENOMEM;
+		return PTR_ERR(max77843->i2c_muic);
 	}
 
 	i2c_set_clientdata(max77843->i2c_muic, max77843);

drivers/extcon/extcon-sm5502.c

@@ -597,7 +597,7 @@ static int sm5022_muic_i2c_probe(struct i2c_client *i2c,
 
 		ret = devm_request_threaded_irq(info->dev, virq, NULL,
 						sm5502_muic_irq_handler,
-						IRQF_NO_SUSPEND,
+						IRQF_NO_SUSPEND | IRQF_ONESHOT,
 						muic_irq->name, info);
 		if (ret) {
 			dev_err(info->dev,