提交 76fbf96f 编写于 作者: E Ed Lin 提交者: James Bottomley

[SCSI] stex: change wait loop code

The original wait loop may be much longer than intended time.
Use more accurate timer_after for it. Also adjust wait value to
avoid unnecessary long waiting.
Signed-off-by: NEd Lin <ed.lin@promise.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>
上级 94e9108b
......@@ -76,9 +76,10 @@ enum {
MU_STATE_STARTED = 4,
MU_STATE_RESETTING = 5,
MU_MAX_DELAY_TIME = 240000,
MU_MAX_DELAY = 120,
MU_HANDSHAKE_SIGNATURE = 0x55aaaa55,
MU_HANDSHAKE_SIGNATURE_HALF = 0x5a5a0000,
MU_HARD_RESET_WAIT = 30000,
HMU_PARTNER_TYPE = 2,
/* firmware returned values */
......@@ -910,23 +911,22 @@ static int stex_handshake(struct st_hba *hba)
struct handshake_frame *h;
dma_addr_t status_phys;
u32 data;
int i;
unsigned long before;
if (readl(base + OMR0) != MU_HANDSHAKE_SIGNATURE) {
writel(MU_INBOUND_DOORBELL_HANDSHAKE, base + IDBL);
readl(base + IDBL);
for (i = 0; readl(base + OMR0) != MU_HANDSHAKE_SIGNATURE
&& i < MU_MAX_DELAY_TIME; i++) {
before = jiffies;
while (readl(base + OMR0) != MU_HANDSHAKE_SIGNATURE) {
if (time_after(jiffies, before + MU_MAX_DELAY * HZ)) {
printk(KERN_ERR DRV_NAME
"(%s): no handshake signature\n",
pci_name(hba->pdev));
return -1;
}
rmb();
msleep(1);
}
if (i == MU_MAX_DELAY_TIME) {
printk(KERN_ERR DRV_NAME
"(%s): no handshake signature\n",
pci_name(hba->pdev));
return -1;
}
}
udelay(10);
......@@ -965,19 +965,18 @@ static int stex_handshake(struct st_hba *hba)
readl(base + IDBL); /* flush */
udelay(10);
for (i = 0; readl(base + OMR0) != MU_HANDSHAKE_SIGNATURE
&& i < MU_MAX_DELAY_TIME; i++) {
before = jiffies;
while (readl(base + OMR0) != MU_HANDSHAKE_SIGNATURE) {
if (time_after(jiffies, before + MU_MAX_DELAY * HZ)) {
printk(KERN_ERR DRV_NAME
"(%s): no signature after handshake frame\n",
pci_name(hba->pdev));
return -1;
}
rmb();
msleep(1);
}
if (i == MU_MAX_DELAY_TIME) {
printk(KERN_ERR DRV_NAME
"(%s): no signature after handshake frame\n",
pci_name(hba->pdev));
return -1;
}
writel(0, base + IMR0);
readl(base + IMR0);
writel(0, base + OMR0);
......@@ -1059,7 +1058,7 @@ static void stex_hard_reset(struct st_hba *hba)
pci_bctl &= ~PCI_BRIDGE_CTL_BUS_RESET;
pci_write_config_byte(bus->self, PCI_BRIDGE_CONTROL, pci_bctl);
for (i = 0; i < MU_MAX_DELAY_TIME; i++) {
for (i = 0; i < MU_HARD_RESET_WAIT; i++) {
pci_read_config_word(hba->pdev, PCI_COMMAND, &pci_cmd);
if (pci_cmd != 0xffff && (pci_cmd & PCI_COMMAND_MASTER))
break;
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册