ath10k: remove repeated words in comments

Found by latest checkpatch.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1603802288-21158-1-git-send-email-kvalo@codeaurora.org

drivers/net/wireless/ath/ath10k/core.c

@@ -2636,7 +2636,7 @@ int ath10k_core_start(struct ath10k *ar, enum ath10k_firmware_mode mode,
 		if (status)
 			goto err;
 
-		/* Some of of qca988x solutions are having global reset issue
+		/* Some of qca988x solutions are having global reset issue
 		 * during target initialization. Bypassing PLL setting before
 		 * downloading firmware and letting the SoC run on REF_CLK is
 		 * fixing the problem. Corresponding firmware change is also

drivers/net/wireless/ath/ath10k/debug.c

@@ -1764,7 +1764,7 @@ static ssize_t ath10k_write_simulate_radar(struct file *file,
 	struct ath10k *ar = file->private_data;
 	struct ath10k_vif *arvif;
 
-	/* Just check for for the first vif alone, as all the vifs will be
+	/* Just check for the first vif alone, as all the vifs will be
 	 * sharing the same channel and if the channel is disabled, all the
 	 * vifs will share the same 'is_started' state.
 	 */

drivers/net/wireless/ath/ath10k/mac.c

@@ -5457,7 +5457,7 @@ static int ath10k_add_interface(struct ieee80211_hw *hw,
 	/* Some firmware revisions don't wait for beacon tx completion before
 	 * sending another SWBA event. This could lead to hardware using old
 	 * (freed) beacon data in some cases, e.g. tx credit starvation
-	 * combined with missed TBTT. This is very very rare.
+	 * combined with missed TBTT. This is very rare.
 	 *
 	 * On non-IOMMU-enabled hosts this could be a possible security issue
 	 * because hw could beacon some random data on the air.  On

drivers/net/wireless/ath/ath10k/rx_desc.h

@@ -68,7 +68,7 @@ struct rx_attention {
  *		first_msdu is set.
  *
  * peer_idx_invalid
- *		Indicates no matching entries within the the max search
+ *		Indicates no matching entries within the max search
  *		count.  Only set when first_msdu is set.
  *
  * peer_idx_timeout

drivers/net/wireless/ath/ath10k/sdio.c

@@ -1248,7 +1248,7 @@ static int ath10k_sdio_bmi_exchange_msg(struct ath10k *ar,
 	 *        Wait for first 4 bytes to be in FIFO
 	 *        If CONSERVATIVE_BMI_READ is enabled, also wait for
 	 *        a BMI command credit, which indicates that the ENTIRE
-	 *        response is available in the the FIFO
+	 *        response is available in the FIFO
 	 *
 	 *  CASE 3: length > 128
 	 *        Wait for the first 4 bytes to be in FIFO

drivers/net/wireless/ath/ath10k/wmi.h

@@ -3832,7 +3832,7 @@ enum wmi_pdev_param {
 	WMI_PDEV_PARAM_BEACON_TX_MODE,
 	/*
 	 * Resource manager off chan mode .
-	 * 0: turn off off chan mode. 1: turn on offchan mode
+	 * 0: turn off offchan mode. 1: turn on offchan mode
 	 */
 	WMI_PDEV_PARAM_RESMGR_OFFCHAN_MODE,
 	/*
@@ -3936,7 +3936,7 @@ enum wmi_10x_pdev_param {
 	WMI_10X_PDEV_PARAM_BEACON_TX_MODE,
 	/*
 	 * Resource manager off chan mode .
-	 * 0: turn off off chan mode. 1: turn on offchan mode
+	 * 0: turn off offchan mode. 1: turn on offchan mode
 	 */
 	WMI_10X_PDEV_PARAM_RESMGR_OFFCHAN_MODE,
 	/*