Merge tag 'imx-fixes-5.11-2' into imx/dt

i.MX fixes for 5.11, round 2:

- Fix pcf2127 reset for imx7d-flex-concentrator board.
- Fix i.MX6 suspend with Thumb-2 kernel.
- Fix ethernet-phy address issue on imx6qdl-sr-som board.
- Fix GPIO3 `gpio-ranges` on i.MX8MP.
- Select SOC_BUS for IMX_SCU driver to fix build issue.

arch/arm/boot/dts/imx6q-tbs2910.dts

@@ -16,6 +16,13 @@
 		stdout-path = &uart1;
 	};
 
+	aliases {
+		mmc0 = &usdhc2;
+		mmc1 = &usdhc3;
+		mmc2 = &usdhc4;
+		/delete-property/ mmc3;
+	};
+
 	memory@10000000 {
 		device_type = "memory";
 		reg = <0x10000000 0x80000000>;

arch/arm/boot/dts/imx6qdl-gw52xx.dtsi

@@ -418,7 +418,7 @@
 
 			/* VDD_AUD_1P8: Audio codec */
 			reg_aud_1p8v: ldo3 {
-				regulator-name = "vdd1p8";
+				regulator-name = "vdd1p8a";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-boot-on;

arch/arm/boot/dts/imx6qdl-kontron-samx6i.dtsi

@@ -137,7 +137,7 @@
 
 	lcd_backlight: lcd-backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm4 0 5000000>;
+		pwms = <&pwm4 0 5000000 0>;
 		pwm-names = "LCD_BKLT_PWM";
 
 		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
@@ -167,7 +167,7 @@
 		i2c-gpio,delay-us = <2>; /* ~100 kHz */
 		#address-cells = <1>;
 		#size-cells = <0>;
-		status = "disabld";
+		status = "disabled";
 	};
 
 	i2c_cam: i2c-gpio-cam {
@@ -179,7 +179,7 @@
 		i2c-gpio,delay-us = <2>; /* ~100 kHz */
 		#address-cells = <1>;
 		#size-cells = <0>;
-		status = "disabld";
+		status = "disabled";
 	};
 };
 

arch/arm/boot/dts/imx6qdl-sr-som.dtsi

@@ -53,7 +53,6 @@
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_microsom_enet_ar8035>;
-	phy-handle = <&phy>;
 	phy-mode = "rgmii-id";
 	phy-reset-duration = <2>;
 	phy-reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
@@ -63,10 +62,19 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		phy: ethernet-phy@0 {
+		/*
+		 * The PHY can appear at either address 0 or 4 due to the
+		 * configuration (LED) pin not being pulled sufficiently.
+		 */
+		ethernet-phy@0 {
 			reg = <0>;
 			qca,clk-out-frequency = <125000000>;
 		};
+
+		ethernet-phy@4 {
+			reg = <4>;
+			qca,clk-out-frequency = <125000000>;
+		};
 	};
 };
 

arch/arm/boot/dts/imx7d-flex-concentrator.dts

@@ -115,6 +115,7 @@
 		compatible = "nxp,pcf2127";
 		reg = <0>;
 		spi-max-frequency = <2000000>;
+		reset-source;
 	};
 };
 

arch/arm/mach-imx/suspend-imx6.S

@@ -67,6 +67,7 @@
 #define MX6Q_CCM_CCR	0x0
 
 	.align 3
+	.arm
 
 	.macro  sync_l2_cache
 

arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi

@@ -101,7 +101,7 @@
 	reboot {
 		compatible ="syscon-reboot";
 		regmap = <&rst>;
-		offset = <0xb0>;
+		offset = <0>;
 		mask = <0x02>;
 	};
 

arch/arm64/boot/dts/freescale/imx8mn.dtsi

@@ -253,7 +253,7 @@
 			#size-cells = <1>;
 			ranges;
 
-			spba: bus@30000000 {
+			spba: spba-bus@30000000 {
 				compatible = "fsl,spba-bus", "simple-bus";
 				#address-cells = <1>;
 				#size-cells = <1>;

arch/arm64/boot/dts/freescale/imx8mp.dtsi

@@ -266,7 +266,7 @@
 				#gpio-cells = <2>;
 				interrupt-controller;
 				#interrupt-cells = <2>;
-				gpio-ranges = <&iomuxc 0 56 26>, <&iomuxc 0 144 4>;
+				gpio-ranges = <&iomuxc 0 56 26>, <&iomuxc 26 144 4>;
 			};
 
 			gpio4: gpio@30230000 {

drivers/firmware/imx/Kconfig

@@ -13,6 +13,7 @@ config IMX_DSP
 config IMX_SCU
 	bool "IMX SCU Protocol driver"
 	depends on IMX_MBOX
+	select SOC_BUS
 	help
 	  The System Controller Firmware (SCFW) is a low-level system function
 	  which runs on a dedicated Cortex-M core to provide power, clock, and

drivers/soc/imx/Kconfig

@@ -13,7 +13,7 @@ config SOC_IMX8M
 	depends on ARCH_MXC || COMPILE_TEST
 	default ARCH_MXC && ARM64
 	select SOC_BUS
-	select ARM_GIC_V3 if ARCH_MXC
+	select ARM_GIC_V3 if ARCH_MXC && ARCH_MULTI_V7
 	help
 	  If you say yes here you get support for the NXP i.MX8M family
 	  support, it will provide the SoC info like SoC family,